QSC PLX 1804 Operation & User’s Manual

Text of QSC PLX 1804 Operation & User’s Manual

QSC PLX 1804 PLX Series Professional Audio Amplifiers

User Manual 4-ohm minimum impedance models with Speakon® output terminals: PLX 1104 PLX 1804 2-ohm minimum impedance models with Speakon and binding post terminals: PLX 1802 PLX 2502 PLX 3102 PLX 3602 *TD-000214-00* TD-000214-00 Rev.E

Important Safety Precautions & Explanation of Symbols

1- Read these instructions. 2- Keep these instructions. 3- Heed all warnings. 4- Follow all instructions. 5- WARNING: To prevent fire or electric shock, do not expose this equipment to rain or moisture. Do not use this apparatus near water. 6- Clean only with a dry cloth. 7- Do not block any ventilation openings. 8- Do not install near any heat sources such as radiators, heat registers, stoves, or

Thank you for purchasing this QSC power amplifier. Please read the following directions to obtain the best results. This manual covers all

models of the PLX series. Illustrations show the PLX 1804 to be representative of the PLX 1104 and 1804 models, while the PLX 3602 illus- tration is representative of the PLX 1802, PLX 2502, PLX 3102, and PLX 3602 models. The PLX 1104 and PLX 1804 models feature: •4-ohm minimum impedance •Speakon

Use four screws and washers to mount the amplifier to the

equipment rack rails. To use the amplifier outside a rack, attach the self-adhesive rubber feet to the bottom. For portable, mobile, or other applications where the rack assembly may be moved, we strongly recommend support- ing the rear of the amplifier. A rear rack ear kit is available from QSC’s Technical Services Group. The cast front panel includes finger grips at each end,

Air flows from the rack, into the back of the amplifier, and out the

front. This keeps the rack cool. The fan automatically runs faster when the amp is working hard. Do not block the front or rear air vents! AC Mains Connection Connect AC power to the IEC socket on the back of the amplifier. NOTE: Turn off the AC power switch before connecting AC power. Connect the AC mains plug to a suitable AC mains outlet. The correct AC line voltage is sho

Input Configuration Switch (PLX 1802/2502/3102/3602 models only)

Select the input configuration by sliding the switch to the position which corresponds with the desired input configuration. •Bridge- upper position •Stereo- middle position •Parallel- lower position Stereo Mode: Each channel remains independent, and each may be used for a different signal. Parallel Mode: This setting connects both inputs together. One input signal feeds both chan-

Each channel has a balanced XLR (female) and 1/4-inch TRS input. The XLR and TRS

connectors for each channel are wired in parallel and can be used for “daisy chain- ing” an input signal to additional amplifiers. The input impedance is 20k ohm balanced or 10k ohm unbalanced. Both XLR and TRS inputs are connected with standard cables and can be changed quickly. Pinouts are marked on the rear panel. Do not attempt to connect more than one inpu

QSC PLX 1804 The PLX 1104 and PLX 1804 models are equipped with Speakon output

connectors for each channel. PLX 1802, PLX 2502, PLX 3102, and PLX 3602 models are equipped with Speakon and binding post output connectors. Wiring connections are shown on the back of the chassis. Carefully note the markings and maintain consistent loudspeaker polarity for optimum system performance. Speakon Output Connectors If making Speakon cables, be sure to connect the lou

The LED indicators can be used to monitor system operation and identify common problems.

POWER (PWR): BLUE Normal indication: •AC switch ON: LED will illuminate; on some models, LED will illuminate dimly during startup sequence. If no indication: •Check AC power cord and AC outlet. •Confirm that AC switch is in ON position. CLIP: RED Normal indication: •Illuminates whenever the amplifier is driven beyond full power. The resulti

Turn the GAIN controls clockwise to increase gain and

counter clockwise to decrease gain. The GAIN controls are marked in dB of attenuation. There are 21 detents for repeatable adjustments. The upper 14 steps are about 1 dB each, and settings should normally be made within this range. The range below - 14 dB should not be used for normal program levels, as the input headroom could be exceeded, but can be used for testing at reduced leve

Both amplifier platforms are fully protected against adverse conditions, but their behavior and user adjustments are different.

PLX 1802/2502/3102/3602 models: •Clip Limiting may be switched on the rear panel to prevent severe overdrive. This protects speakers and somewhat reduces the load on the amplifier. •Internal current limits protect the output transistors against overloading. Peak limiting may occur at full output if usi

Specifications PLX 1104, PLX 1804

PLX 1104 PLX 1804 OUTPUT POWER (Watts)(1) 20 - 20k Hz, 0.05% THD, 8 ohms/Ch. 310 550 1k Hz, 0.1% THD (EIA), 8 ohms/Ch. 325 600 20 - 20k Hz, 0.05% THD, 4 ohms/Ch. 500 800 1k Hz, 0.1% THD (EIA), 4 ohms/Ch. 550 900 DISTORTION, SMPTE-IM 0.02% 0.02% FREQUENCY RESPONSE 20 - 20k Hz, ±0.5 dB, all models SIGNAL to NOISE, unweighted, 20 - 20k Hz -108 dB -106 dB VOLTAGE GAIN 32.5 dB 34.9 dB INPUT SENSITIVITY, Vrms for rated po

Specifications PLX 1802, PLX 2502, PLX 3102, PLX 3602

PLX 1802 PLX 2502 PLX 3102 PLX 3602 OUTPUT POWER (Watts)(1) 20 - 20k Hz, 0.05% THD, 8 ohms/Ch. 320 425 550 725 1k Hz, 0.1% THD (EIA), 8 ohms/Ch. 330 450 600 775 20 - 20k Hz, 0.05% THD, 4 ohms/Ch. 525 675 900 1100 1k Hz, 0.1% THD (EIA), 4 ohms/Ch. 575 750 1000 1250 1k Hz, 0.1% THD (EIA), 2 ohms/Ch. 900 1250 1550 1800 Bridge Mono, 20 - 20k Hz, 0.1% THD, 8 ohms 1100 1400 1900 2500 Bridge Mono, 1k Hz,

Appendix A: Speakon Wiring Reference

Amplifier connection To loudspeaker Two-wire, single-channel connection Four-wire, two-channel connection Bridge mode connection NOTE! Ensure proper polarity when connecting bridge mode output!

QSC PLX 1804 Precauciones importantes de seguridad y explicación de los símbolos

1- Lea estas instrucciones. 2- Conserve estas instrucciones. 3- Observe todas las advertencias. 4- Siga todas las instrucciones. 5- ADVERTENCIA: Para prevenir incendios o descargas eléctricas, no exponga este equipo a la lluvia ni a la humedad. No use este aparato cerca del agua. 6- Límpielo sólo con un paño seco. 7- No obstruya ninguna abertura de ventilación. 8- No lo instal

Muchas gracias por la compra de este amplificador de potencia QSC. Por favor lea las siguientes instrucciones para obtener los mejores

resultados. Este manual cubre todos los modelos de la serie PLX. Las ilustraciones muestran al modelo PLX 1804 como representativo de los modelos PLX 1104 y 1804, mientras que la ilustración del modelo PLX 3602 es representativo de los modelos PLX 1802, PLX 2502, PLX 3102 y PLX 3602. Los modelos PLX 11

Montaje en bastidor

Use cuatro tornillos y arandelas para montar el amplificador en los rieles del bastidor del equipo. Para usar el amplificador sin bastidor, instale las patas de caucho autoadhesivas en la parte inferior. Para aplicaciones portátiles, móviles u otras aplicaciones donde puede moverse el conjunto del bastidor, recomendamos enfáticamente sujetar la parte posterior del amplificador. Se dispone de un juego de orejas de montaje poster

QSC Amplifier Owners Instructions: