Ramsey Electronics PR20 Specification Sheet

Text of Ramsey Electronics PR20 Specification Sheet

16 db Gain, 1 db Noise Figure

• Runs on 9 to 15 VDC • Hi-Q tuned input to reduce overload • Small size to fit in any rig • The most popular preamp kit in the USA! • Easy 15 minute assembly Perk up your reception on 220 MHz with this easy-to-build and install kit. Works well with any radio - especially effective in repeaters. Rugged design using a microwave transistor outperforms units costing triple the

INTRODUCTION TO THE PR20 LOW NOISE PREAMPLIFIER

A “preamplifier” gives an initial boost, measured in decibels, to the level of a signal before it is further processed by tuned circuits, filters, amplifiers, mixers, detectors, or other circuit stages. Preamps may be designed for either RF or audio use and may be either tuned or broadbanded. The Ramsey Low Noise PR10, 20, and 40 Preamplifiers for 144, 220, and 440 MHz, respectively, differ from

L1 and C2 form a tuned input filter for the preamp to reject out-of-band signals. The 3 db

bandwidth of this filter is 6MHz. L1 is adjustable for peak performance. The 2SC2498 transistor is a bipolar silicon NPN low noise UHF/VHF amplifier in a TO-92 case suitable for service up to 5 GHz, with maximum device dissipation of 600 milliwatts. Q1 has a very low noise figure, determined by the bias established by R1 and R2. The actua

PARTS SUPPLIED WITH PR20 KIT

CAPACITORS ‰ 2 2 or 2.2pF disc capacitor (C1,2) ‰ 1 10pF disc capacitor (C3) ‰ 1 100pF disc capacitor [marked 100 or 101] (C4) ‰ 1 .01uF disc capacitor [may be marked .01, 103, or 10nF] (C5) RESISTORS ‰ 1 470 ohm [yellow-violet-brown] (R1) ‰ 1 100K ohm [brown-black-yellow] (R2) OTHER COMPONENTS ‰ 1 PRX printed circuit board ‰ 1 shielded adjustable coil (L1) [marked 359-7787] ‰ 1 2SC2498 or 2570 microw

PR20 PRE-AMP ASSEMBLY PROCEDURE

Soldering nine parts to a PC board is not a big job, but good performance of the PR20 requires attention to keeping all leads as short and neat as possible. The order of parts installation is not critical for this and other small kits, so the purpose of the following suggested order of assembly is just to make it as easy as possible for you to get the parts placed correctly on the first try. For your convenience, th

‰ 3. Install C4, 100pF (marked 100 or 101).

‰ 4. Install C5, .01uF (marked .01 or 103 or 10nF). Disc capacitor C5 is the bypass capacitor for the DC voltage supply points on the PC board. ‰ 5. Install Q1, 2SC2498. Press Q1 into its respective location on the PC board, which should be quite obvious by the placement of the previous parts. Orient the flat side as shown on the PC board illustration. Press the transistor in place firm

two mechanical points after making sure that L1 is pressed firmly against the

component side of the PC board. PROGRESS SUMMARY: The wiring of your Ramsey PR series preamp PC board is now complete. It will take you less than a minute to completely recheck every single soldering connection as well as for the appropriate part installations. Correct parts placement checked.

TESTING AND ADJUSTMENT

With your preamp installed between antenna and receiver, the only adjustment needed is the obvious one: peaking L1 for maximum signal strength. This may require more patience than most of us would think, because the adjustment should be made on a weak signal transmitting long enough to permit the adjustment. Since this is a low noise preamp, don’t look for an imaginary increase in noise level or waste time trying to make a

PR20 ON-OFF SWITCHING SUGGESTION

Depending on your particular application and intended frequency, you may wish to use a DPDT power switch with one pole controlling voltage and the other pole connecting the input and output of the PR20 when the DC supply voltage is in the “OFF” position. This setup is very practical when you want to switch the preamp in and out of a receiver antenna line. ALL RF connections to the switch should be as short as

A 220 MHz “ACTIVE ANTENNA”

For situations where a simple indoor receiving antenna is needed, the PR20 preamp will add considerably improved performance to a whip antenna adjusted to 1/4 or 5/8 wave. And, for a very well engineered true active antenna for both HF and VHF at a break-through low price, take a look at our new model AA7 Active Antenna kit which features an on-board battery supply, adjustable gain control, heavy-duty whip, HF-VHF

The 2SC2498 transistor is a bipolar silicon NPN low noise UHF/VHF amplifier in a TO-92

case, suitable for service up to 5GHz, with maximum device dissipation of 600 milliwatts. Other maximum ratings: Collector -to-Base Voltage: 25 V Collector-to-Emitter Voltage: 12 V Base-to-Emitter Voltage: 3 V Maximum Collector Current: 70 mA Standard replacements: ECG10 or SK9139. You may, of course, order replacement 2SC

Ramsey Electronics PR20 The only possible causes for malfunction of the PR20 are faulty or incorrectly installed

parts. Re-check your work. Transistor replacement information is provided. Poor performance such as oscillation can be caused by bad parts-mounting (excessive lead length of resistors or capacitors). Erratic operation will be traced to poor input, output, or voltage connections, or a faulty solder connection. CONCLUSION Please make sure

Ramsey Electronics PR20 THE RAMSEY PR2: THE ULTIMATE BROADBAND PREAMPLIFIER

After you find out how practical a well-built PR20 can be for 220MHz operating, you will be quite impressed with the “all bands” higher gain (also with very low noise) plus the convenient AC power supply, BNC I/O connectors and LED ON-OFF indicator of the Ramsey PR2, available factory-wired. The PR2 uses advanced microwave MMIC for signal- to-noise figures that are typically 27db (over 4 “

The Ramsey Kit Warranty

Please read carefully BEFORE calling or writing in about your kit. Most problems can be solved without contacting the factory. All Ramsey kits will work if assembled properly. The very fact that your kit includes this new manual is your assurance that a team of knowledgeable people have field-tested several "copies" of this kit straight from the Ramsey Inventory. If you need help, please read through your manual carefully;

Ramsey Electronics PR20 Published by Ramsey Electronics, Inc.

Copyright 1994 All rights reserved. Ramsey Electronics, Inc. 590 Fishers Station Drive Victor, NY 14564 Phone (585) 924-4560 Fax (585) 924-4555 www.ramseykits.com Call or write for our full line catalog! PARTIAL LIST OF AVAILABLE KITS RAMSEY TRANSMITTER KITS • FM10A, FM25B Stereo Transmitters • AM1, AM25 AM Transmitters • TV6 Television Transmitter • FM100B Profes

Ramsey Electronics Amplifier Owners Instructions: