Sharp KB-6024MS Service Manual

Text of Sharp KB-6024MS Service Manual

In the interest of user-safety the unit should be restored to its original condition and only parts identical to those specified should

be used. WARNING TO SERVICE PERSONNEL: This service manual is intended for use by persons having electrical and mechanical training and a level of knowledge of these subjects generally considered acceptable in the appliance repair trade. Sharp Electronics Corporation cannot be responsible,

PRECAUTIONS TO BE OBSERVED BEFORE AND DUR-

ING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY (a) Do not operate or allow the oven to be operated with the door open. (b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary: (1) interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arci

WARNING TO SERVICE PERSONNEL

Microwave Oven units contain circuitry capable of producing very high voltage and current, contact with following parts may result in a severe, possibly fatal, electrical shock. (Example) High Voltage Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness, Heating Elements, etc.. Read the Service Manual carefully and follow all instruc

Sharp KB-6024MS MICROWAVE MEASUREMENT PROCEDURE

A. Requirements: 1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven should not exceed 1mW/cm2 at any point 5cm or more from the external surface of the oven, measured prior to acquisition by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2 at any point 5cm or more from the external surface of the o

SHARP ELECTRONICS CORPORATION

SHARP PLAZA, MAHWAH, NEW JERSEY 07430-2135 SERVICE MANUAL MICROWAVE DRAWERS KB-6024MS / KB-6024MK / KB-6024MW KB-6025MS / KB-6025MK / KB-6025MW FOREWORD This Manual has been prepared to provide Sharp Electronics Corp. Service Personnel and Service Information for the MICROWAVE DRAWERS, KB-6024MS, KB-6024MK, KB-6024MW and KB-6025MS, KB-6025MK, KB-6025MW. It is recommended that service personnel c

14.5 Amperes, 1000 watts

60 Hz Single phase, 3 wire grounded Power Output 1000 watts (IEC TEST PROCEDURE) Operating frequency of 2450MHz Cooking Cavity Dimensions KB6024 Width 17-11/32 KB6025 Width 17-11/32 Height 5-7/8" Height 5-7/8" 1.0 Cubic Feet Depth 17-1/8" Depth 17-1/8" Outside Dimensions KB6024 Width 23-7/8"

This oven is equipped with a three prong grounding plug. It must be plugged into a wall receptacle that is properly installed

and grounded in accordance with the National Electrical Code and local codes and ordinances. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. WARNING: Improper use

DESCRIPTION OF OPERATING SEQUENCE

The following is a description of component functions dur- ing oven operation. OFF CONDITION Closing the drawer activates the door sensing switch and secondary interlock switch. (In this condition, the monitor switch contacts are opened.) When oven is plugged in, 120 volts A.C. is supplied to the control unit. (Page 10). 1. The display will show flashing "Enjoy Your Drawer Touch C

Sharp KB-6024MS SENSOR COOKING CONDITION

Using the SENSOR function, food is cooked without figur- ing time, power level or quantity. When the oven senses enough steam from the food, it relays the information to its microprocessor which will calculate the remaining cooking time and power level needed for best results. When the food is cooked, water vapor is developed. the sensor "senses" the vapor and its resistance increase gradually.

NOISE SUPRESSION COIL

RESISTOR 470 k? 1/2W LINE CROSS CAPACITOR 1.0 ? F 275V LINE BYPASS CAPACITOR 0.0033 ? F 250V FUSE 20A FAN MOTOR OVEN LAMP MONITOR SWITCH PRIMARY INTERLOCK RELAY H.V. RECTIFIER MAGNETRON POWER TRANSFORMER CAPACITOR 1.00 ? F AC 2300V STIRRER MOTOR CONTR OL UNIT MICROWAVE DRAWER S WITCHING R E GULATOR OVEN THERMAL CUT-OUT MG THERMAL CUT-OUT SECONDARY INTELOCK SWITCH MICROWAVE DRAWER DOOR O

unlike conventional microwave ovens, proper maintenance cannot be performed with only a voltmeter

and ohmmeter. In this service manual, the touch control panel assembly is divided into three units, Control Unit, Keyboard Unit and Power Unit, and troubleshooting by unit replacement is described according to the symptoms indicated. Before testing, 1) Disconnect the power supply

4) Reconnect all leads removed from components during testing.

5) Re-install the covers. 6) Reconnect the power supply cord after the covers are installed. 7) Run the oven and check all functions. TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST B KEY UNIT TEST 1. Disconnect the power supply cord, and then remove outer case. 1. Disconnect the power supply cord, and then remove

Sharp KB-6024MS WARNING : The oven should be fully assembled before following procedure.

(1) Place one cup of water in the center of the tray in the oven cavity. (2) Close the drawer, touch the Defrost pad. Then select Steaks/Chops by touching the number pad 2. And touch the number pad 5. (Now, weight 0.5lb is set.) And then touch the start pad. (3) The oven is in Defrost cooking condition. (4) The oven will operate as follows WEIGHT 1
WARNING : The oven should be fully assembled before following procedure. (1) The oven should be plugged in at least two minutes before sensor cooking. (2) Room temperature should not exceed 95 οF (35 οC). (3) The unit should not be installed in any area where heat and steam are generated. The unit should not be installed, for example, next to a conventional surface unit. Refer to the “INSTALLATION INSTRUCTIONS” of

9-2. Place the container on the center of tray in the oven cavity.

9-3. Close the drawer. 9-4. Touch the TIMER/CLOCK pad once, the POWER LEVEL pad twice and the START pad once. And touch the number pads 1 once and the number pad 4 once. 9-5. The control panel is in automatic Sensor operation. 9-6. The oven turns off automatically, and the time for detecting moisture will be di

2. Open the drawer and keep it open.

3. To discharge high voltage capacitor, wait for 60 seconds. 4. To test for an open filament, isolate the magnetron from the high voltage circuit. A continuity check across the magnetron filament leads should indicate less than 1 ohm. 5. To test for a shorted magnetron, connect the ohmmeter leads between the magnetron filament leads and chassis ground. This test should indicate an in

Sharp KB-6024MS SECONDARY INTERLOCK SWITCH TEST

STOP SWITCH 1. Disconnect the power supply cord. 2. Open the drawer and keep it open. 3. To discharge high voltage capacitor, wait for 60 seconds. 4. Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal of the switch. The meter should indicate an open circuit with the drawer open and a closed circuit with the drawer closed. If improper operati

POWER TRANSFORMER TEST

1. Disconnect the power supply cord. 2. Open the drawer and block it open. 3. Discharge high voltage capacitor. 4. Disconnect the primary input terminals and measure the resistance of the transformer with an ohmmeter. Check for continuity of the coils with an ohmmeter. On the R x 1 scale, the resistance of the primary coil should be less than 1 ohm

TOUCH CONTROL PANEL ASSEMBLY

OUTLINE OF TOUCH CONTROL PANEL The touch control section consists of the following units. (1) Key unit (2) Control Unit (3) Power unit The principal functions of these units and the signals com- municated among them are explained below. Key unit The key unit is composed of a matrix, signals generated in the LSI are sent to the key unit from P10 - P17. When a key pad is touched, a signal is compl

1 - 3

AN5- AN3 IN Terminal to change cooking input according to the Model. By using A/D converter contained in the LSI, DC voltage in accordance with the Model in operation is applied to set up its cooking constant. 4 AN2 IN Input signal which inform the drawer door is in the middle position between the opened position and the closed position, to LSI from the door position switch rear. 5 AN1 IN Terminal not used. 6 AN0 IN T

Sharp Microwave Oven Owners Instructions: