Sharp R-200BK Service Manual

Text of Sharp R-200BK Service Manual

In the interest of user-safety the oven should be restored to its original

condition and only parts identical to those specified should be used. WARNING TO SERVICE PERSONNEL: Microwave ovens con- tain circuitry capable of producing very high voltage and current, contact with following parts may result in a severe, possibly fatal, electrical shock. (High Voltage Capacitor, High Voltage Power Transformer, Magnetron, High Voltag

PRECAUTIONS TO BE OBSERVED BEFORE AND

DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY (a) Do not operate or allow the oven to be operated with the door open. (b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary: (1) interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and other

WARNING TO SERVICE PERSONNEL

Microwave ovens contain circuitry capable of pro- ducing very high voltage and current, contact with following parts may result in a severe, possibly fatal, electrical shock. (Example) High Voltage Capacitor, High Voltage Power Trans- former, Magnetron, High Voltage Rectifier Assem- bly, High Voltage Harness etc.. Read the Service Manual carefully and follow all instructions. Before Servicing 1. Disconnect t

MICROWAVE MEASUREMENT PROCEDURE

A. Requirements: 1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven should not exceed 1mW/cm2 at any point 5cm or more from the external surface of the oven, measured prior to acquisition by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2 at any point 5cm or more from the external surface of the oven. 2) Safety i

SHARP ELECTRONICS CORPORATION

SHARP PLAZA, MAHWAH, NEW JERSEY 07430-2135 SERVICE MANUAL MICROWAVE OVEN R-200BK/ R-200BW FOREWORD This Manual has been prepared to provide Sharp Electronics Corp. Service Personnel with Operation and Service Information for the SHARP MICROWAVE OVEN, R-200BK, R-200BW. It is recommended that service personnel carefully study the entire text of this manual so that they will be qualified to render satisfactory

This oven is equipped with a three prong grounding plug. It must be plugged into a wall receptacle that is properly installed

and grounded in accordance with the National Electrical Code and local codes and ordinances. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an

1. Oven door with see-through window

2. Safety door latches. 3. Door hinges 4. Door seals and sealing surfaces 5. Turntable motor shaft 6. Removable turntable support 7. Removable turntable 8. Ventilation openings. (Rear) 9. Oven lamp. 10. Wave guide cover. 11. Power supply cord CONTROL PANEL 8 10 11 9 1 2 5 7 3 4 6 BAKED POTATO COOK 1 medium 4 5min. FRESH VEGETABLES COOK 2 cups 6 8min. DINNE

NOTE: CONDITION OF OVEN

1. LIGHT UP DIAL OFF. 2. DOOR CLOSED. OPERATION DESCRIPTION OF OPERATING SEQUENCE The following is a description of component functions during oven operation. OFF CONDITION Closing the door activates door sensing switch and second- ary interlock switch. (In this condition, the monitor switch contacts are opened.) When oven is plugged in, 120 volts A.C. is supplied to the control unit. (Figure O-1). COOKIN
NOTE: CONDITION OF OVEN 1. DOOR CLOSED. 2. LIGHT UP DIAL ON. Figure O-2. Oven Schematic-Cooking Condition DESCRIPTION AND FUNCTION OF COMPONENTS DOOR OPEN MECHANISM The door is opened by pulling the door, refer to the Figure D-1. Latch Heads Latch Hook Door Door Sensing Switch Monitor Switch Secondary Interlock Switch Figure D-1. Door Open Mechanism DOOR SENSING AND SECONDARY INTERLOCK SWITCHES The secondary interlock switch is

Sharp R-200BK The turntable motor rotates the turntable located on the

bottom of the oven cavity, so that the food on the turntable is cooked evenly. The turntable may turn in either direction. COOLING FAN MOTOR The cooling fan motor drives a blade which draws external cool air. This cool air is directed through the air vanes surrounding the magnetron and cools the magnetron. This air is channelled through the oven cavity to remove stea

CK = Check / RE = Replace

RE CK A B C D E F F G H RE RE CK I/J CK CK CK K SHORT IN POWER CORD SHORT OR OPEN WIRING MAGNETRON POWER TRANSFORMER H.V. RECTIFIER ASSEMBLY HIGH VOLTAGE CAPACITOR MAGNETRON THERMAL CUT-OUT PRIMARY INTERLOCK SYSTEM SECONDARY INTERLOCK SWITCH MONITOR SWITCH C/T FUSE OVEN LAMP OR SOCKET COOLING FAN MOTOR TURNTABLE MOTOR CONTROL UNIT OR RELAY WRONG OPERATION LOW VOLTAGE DIRTY OVEN CAVITY FOIL PATTERN ON PWB. Home f

Sharp R-200BK POWER TRANSFORMER TEST

1. Disconnect the power supply cord, and then remove outer case. 2. Open the door and block it open. 3. Discharge high voltage capacitor. 4. Disconnect the primary input terminals and measure the resistance of the transformer with an ohmmeter. Check for continuity of the coils with an ohmmeter. On the R x 1 scale, the resistance of the primary coil should be less than 1 ohm and the resistance of the high voltage

SECONDARY INTERLOCK SWITCH TEST

1. Disconnect the power supply cord, and then remove outer case. 2. Open the door and block it open. 3. Discharge high voltage capacitor. 4. Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal of the switch. The meter should indicate an open circuit with the door open and a closed circuit with the door closed. If improper operation is indicated, replace the se

1. Disconnect the power supply cord, and then remove outer case.

2. Open the door and block it open. 3. Discharge high voltage capacitor. 4. Before performing this test, make sure that the secondary interlock switch and the primary interlock relay are operating properly, according to the above Switch Test Procedure. Disconnect the wire lead from the monitor switch (COM) terminal. Check the monitor switch operation by using the ohmmeter a

If the C/T fuse is blown by improper switch operation, the C/T fuse and monitor switch must be

replaced with "C/T fuse and monitor switch assembly" part number FFS-BA020WRK0, even if the monitor switch operates normally. The C/T fuse and monitor switch assembly is comprised of a 13 ampere fuse and switch. A continuity check across the C/T fuse terminals should indicate a closed circuit un

1. Disconnect the power supply cord and then remove outer case.

2. Open the door and block it open. 3. Discharge high voltage capacitor. 4. Disconnect the leads to the primary of the power transformer. 5. Ensure that these leads remain isolated from other components and oven chassis by using insulation tape. 6. After that procedure, re-connect the power supply cord. 7. Remove the outer case and check voltage between Pin No. 5 of the 3 pi

Sharp R-200BK 6) Reconnect all leads removed from components during testing.

7) Re-install the outer case (cabinet). 8) Reconnect the power supply cord after the outer case is installed. 9) Run the oven and check all function. 2. Follow the troubleshooting guide given below, if indicator does not light up after above check and repairs are finished. 1) Disconnect the power supply cord and then remove oute

Sharp Microwave Oven Owners Instructions: