Sharp R-210D Service Manual

Text of Sharp R-210D Service Manual

In interests of user-safety the oven should be restored to its original

condition and only parts identical to those specified should be used. MODEL R-210D S5001R210DPJ/ MICROWAVE OVEN TABLE OF CONTENTS CAUTION, MICROWAVE RADIATION................................................................................................................. 1 WARNING ..................................................................................................

GENERAL IMPORTANT INFORMATION

This Manual has been prepared to provide Sharp Corp. Service engineers with Operation and Service Information. It is recommended that service engineers carefully study the entire text of this manual, so they will be qualified to render satisfactory customer service. CAUTION MICROWAVE RADIATION DO NOT BECOME EXPOSED TO RADIATION FROM THE MICROWAVE GENE

THIS APPLIANCE MUST BE EARTHED

IMPORTANT THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: GREEN-AND-YELLOW : EARTH BLUE : NEUTRAL BROWN : LIVE ITEM DESCRIPTION Power Requirements 230 - 240 Volts 50 Hertz Single phase, 3 wire earthed Power Consumption 1.16 kW Power Output 800 watts nominal of RF microwave energy (IEC Test Procedure) Operating frequency 2450 MHz Case Dimensions Width 460 m

8. Control panel

9. Waveguide cover 10. Power supply cord 11. Turntable 12. Roller stay 1. Ventilation openings 2. Oven lamp 3. Door hinges 4. Door safety latches 5. See through door 6. Door seals sealing surfaces MED MED LOW DEFROST LOW MED HIGH HIGH 0 1 2 3 456 7 8 9 10 11 12 13 14 15 20 25 30 1.0 0.5 DEFROST(kg) DINNER PLATE REHEAT 1 SERVE (400g) SOUP DEFROST FRESH VEGETABLES MED 7-8min. REHEAT 1 c

Closing the door activates all door interlock switches

(1st. latch switch, 2nd. latch switch and stop switch). IMPORTANT When the oven door is closed, the monitor switch contacts (COM-NC) must be open. When the microwave oven is plugged in a wall outlet, rated voltage is supplied to the noise filter and the control unit. Figure O-1 on page 25 MICROWAVE COOKING CONDITION HIGH COOKING Select the power level HIGH by p

Sharp R-210D FUNCTION OF IMPORTANT COMPONENTS

Figure D-1. Door Open Mechanism 1ST. LATCH SWITCH, 2ND. LATCH SWITCH AND STOP SWITCH 1. When the oven door is closed, the contacts (COM-NO) must be closed. 2. When the oven door is opened, the contacts (COM- NO) must be opened. MONITOR SWITCH 1. When the oven door is closed, the contacts (COM-NC) must be opened. 2. When the oven door is opened, the contacts (COM- NC) must be closed. 3. If the oven door is opened a

WARNING TO SERVICE PERSONNEL

Microwave ovens contain circuitry capable of producing very high voltage and current, contact with any part of the high voltage circuit will result in electrocution. High voltage capacitor, Power transformer, Magnetron, High voltage rectifier assembly, High voltage harness. REMEMBER TO CHECK 3D 1) Disconnect the supply. 2) Door opened, and wedged open. 3) Discharge the high voltage capacitor. WARNING: AGAIN

Sharp R-210D H.V. RECTIFIER ASSEMBLY

HIGH VOLTAGE WIRE HIGH VOLTAGE CAPACITOR 1ST. LATCH SWITCH 2ND. LATCH SWITCH STOP SWITCH MONITOR SWITCH MONITOR RESISTOR THERMAL CUT-OUT 125˚C (OVEN) THERMAL CUT-OUT 95˚C (MG) FAN MOTOR TURNTABLE MOTOR FUSE M8A CONTROL PANEL RELAY (RY-1, RY-2) FOIL PATERN ON P.W.B. POWER SUPPLY CORD SHORTED WIRE HARNESS OPENED WIRE HARNESS OVEN LAMP OR SOCKET WALL OUTLET MISADJUSTMENT SWITCH HOME FUSE OR BREAKE

CARRY OUT 3D CHECKS.

Isolate the magnetron from the high voltage circuit by removing all leads connected to the filament terminal. To test for an open circuit filament use an ohmmeter to make a continuity test between the magnetron filament terminals, the meter should show a reading of less than 1 ohm. To test for a short circuit filament to anode condition, connect ohmmeter between one of the filament terminals and the case of the magnetron (grou

Heat up for 54 sec.

B POWER TRANSFORMER TEST CARRY OUT 3D CHECKS. Disconnect the leads to the primary winding of the power transformer. Disconnect the filament and secondary winding connections from the rest of the HV circuitry. Using an ohmmeter, set on a low range, it is possible to check the continuity of all three windings. The following readings should be obtained: WARNING: High voltages and large currents are p

Sharp R-210D HIGH VOLTAGE CAPACITOR TEST

CARRY OUT 3D CHECKS. A. Isolate the high voltage capacitor from the circuit. B. Continuity check must be carried out with measuring instrument which is set to the highest resistance range. C. A normal capacitor shows continuity for a short time (kick) and then a resistance of about 10MΩ after it has been charged. D. A short-circuited capacitor shows continuity all the

to resistricted ventilation, cooling fan failure or a fault condition within the magnetron or HV circuit.

An open circuit temperature fuse (OVEN) indicates that the food in the oven cavity may catch fire, this may be due to overheating produced by improper setting of the cooking time or failure of the control panel. H MOTOR WINDING TEST CARRY OUT 3D CHECKS. Disconnect the leads from the motor. Using

CONTROL PANEL ASSEMBLY TEST

The control panel consists of circuits including semiconductors such as LSI, ICs, etc. Therefore, unlike conventional microwave ovens, proper maintenance can not be performed with only a voltmeter and ohmmeter. In this service manual, troubleshooting by replacement is described according to the symptoms indicated. 1. Control Panel The following symptoms indicate a defec

PROCEDURES TO BE TAKEN WHEN THE FOIL PATTERN ON THE PRINTED WIRING

BOARD(PWB) IS OPEN To protect the electronic circuits, this model is provided with a fine foil pattern added to the input circuit on the PWB, this foil pattern acts as a fuse. If the foil pattern is open, follow the troubleshooting guide given below for repair. Problem: POWER ON, indicator does not light up. CARRY OUT 3D CHECKS. ST

CONTROL PANEL ASSEMBLY

OUTLINE OF CONTROL PANEL 5) Buzzer Circuit The buzzer is responsive to signals from the LSI to emit audible sounds (tact switch touch sound and comple- tion sound). 6) Door Sensing Switch (Stop Switch) A switch to "tell" the LSI if the door is open or closed. 7) Relay Circuit To drive the magnetron, fan motor, turntable motor and light the oven lamp. 8) Encoder The encoder generates the pulse signal, and the pulse signal is

Sharp R-210D DESCRIPTION OF LSI

LSI(IXA023DR) The I/O signal of the LSI(IXA023DR) are detailed in the following table. Pin No. Signal I/O Description 1 D3 OUT Segment data signal. Signal is input to the cathodes of the light-emitting diodes (LD8, LD16 and LD24). 2 D4 OUT Signal to sound buzzer. A: Tact switch touch sound. B: Completion sound. 3 D5 OUT Oven lamp, turntable motor and fan motor driving signal(Square Waveform : 50Hz). To turn on and off shut-off

Signal to synchronize LSI with commercial power source frequency.

This is basic timing for all real time process- ing of LSI. 18-19 AIN0-AIN1 IN Terminal to change functions according to the model. Signal in accordance with the model in operation is applied to set up its function. 20 AIN2 IN Input signal which communicates the door open/close information to LSI. Door closed; "H" level signal. Door opened;

1. Precautions for Handling Electronic Components

This unit uses CMOS LSI in the integral part of the circuits. When handling these parts, the following pre- cautions should be strictly followed. CMOS LSI have extremely high impedance at its input and output terminals. For this reason, it is easily influenced by the surrounding high voltage power source, static electric- ity charge in clothes, etc., and sometimes it is not fully protected by the

COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE

WARNING: Avoid possible exposure to microwave energy. Please follow the instructions below before operating the oven. 1. Disconnect oven from power supply. 2. Visually check the door and cavity face plate for dam- age (dents, cracks, signs of arcing etc.). Carry out any remedial work that is necessary before operating the oven. Do not operate the oven if any of the following conditions exist; 1. Door

Sharp Microwave Oven Owners Instructions: