Sharp R-3A88 Service Manual

Text of Sharp R-3A88 Service Manual

In interests of user-safety the oven should be restored to its original

condition and only parts identical to those specified should be used. MODEL R-3A88 S3614R3A88PX/ MICROWAVE OVEN TABLE OF CONTENTS Page CAUTION, MICROWAVE RADIATION................................................................................................................. 1 WARNING ..........................................................

FUNCTION OF IMPORTANT

COMPONENTS OPERATING SEQUENCE APPEARANCE VIEW MICROWAVE MEASUREMENT WIRING DIAGRAM PARTS LIST TOUCH CONTROL PANEL ASSEMBLY COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE MICROWAVE OVEN R-3A88 GENERAL IMPORTANT INFORMATION This Manual has been prepared to provide Sharp Corp. Service engineers with Operation

Single phase, 3 wire earthed

Power Consumption 1.35 kW Power Output 850 watts nominal of RF microwave energy (IEC 705) Operating fequency 2450 MHz Case Dimensions Width 520 mm Height 305 mm Depth 389mm Cooking Cavity Dimensions Width 348 mm Height 197 mm Depth 368 mm Turntable diameter 325mm Control Complement Touch Control System Clock ( 1:00 - 12:59) Timer (0 - 99 min

TOUCH CONTROL PANEL

a HELP PAD Touch to select child lock, language or demonstration modes. Touch to get cooking information. b REHEAT PAD Touch to reheat 3 popular menus. c RICE COOK PAD Touch to cook rice, congee or porridge. d STEAM MENU PAD Touch to cook steam menus. e. INTERNATIONAL MENUE OADS Touch to cook 3 international menus. f SLOW COOK PAD Touch to cook slowly and longer time. g EASY DEFROST PAD Touch to defrost meat by

Closing the door activates all door interlock switches (1st.

latch switch and 2nd. interlock relay control switch). IMPORTANT When the oven door is closed, the monitor switch contacts (COM-NC) must be open. When the microwave oven is plugged in a wall outlet, rated voltage is supplied to the point A3+A5 in the control unit. Figure O-1 on page 25 1. The display shows SHARP , MICRO- , WAVE and OVEN . 2

Sharp R-3A88 FUNCTION OF IMPORTANT COMPONENTS

DOOR OPEN MECHANISM The door is opened by pushing the open button on the control panel, refer to the Figure D-1. When the open button is pushed, the open button pushes up the switch lever, and then the switch lever pushes up the latch head. The latch heads are moved upward and re- leased from latch hook. Now the door will open. LATCH HEADS LATCH HOOK 2ND. INTERLOCK RELAY CONTROL SWITCH MONITOR SWITCH SWITCH LEVER 1

WARNING TO SERVICE PERSONNEL

Microwave ovens contain circuitry capable of producing very high voltage and current, contact with any part of the high voltage circuit will result in electrocution. High voltage capacitor, Power transformer, Magnetron, High voltage rectifier assembly, High voltage harness. REMEMBER TO CHECK 3D 1) Disconnect the supply. 2) Door opened, and wedged open. 3) Discharge high voltage capacitor. WARNING: AGAINST T

Sharp R-3A88 H.V. RECTIFIER ASSEMBLY

HIGH VOLTAGE CAPACITOR 1ST. LATCH SWITCH 2ND. INTERLOCK RELAY CONTROL SWITCH MONITOR SWITCH MONITOR RESISTOR THERMAL CUT-OUT 95˚C THERMAL CUT-OUT 145˚C FAN MOTOR TURNTABLE MOTOR FUSE M8A TOUCH CONTROL PANEL KEY UNIT RELAY (RY-1, RY-2) FOIL PATTERN ON P.W.B. POWER SUPPLY CORD SHORTED WIRE HARNESS OPENED WIRE HARNESS OVEN LAMP OR SOCKET WALL OUTLET MISADJUSTMENT SWITCH HOME FUSE OR BREAKER BLOCKE

CARRY OUT 3D CHECK.

Isolate the magnetron from high voltage circuit by removing all leads connected to filament terminal. To test for an open circuit filament use an ohmmeter to make a continuity test between the magnetron filament terminals, the meter should show a reading of less than 1 ohm. To test for short filament to anode condition, connect ohmmeter between one of the filament terminals and the case of the m

6. Measure the final water temperature. (Example: The final temperature T2 = 21°C)

7. Calculate the microwave power output P in watts from above formula. Initial temperature .................................................................................................. T1 = 11°C Temperature after (49 + 2) = 51 sec. ..................................................................... T2 = 21°

Sharp R-3A88 TEST PROCEDURES (CONT'D)

PROCEDURE LETTER COMPONENT TEST B C HIGH VOLTAGE RECTIFIER CARRY OUT 4R CHECKS. NOTE: FOR MEASUREMENT OF THE RESISTANCE OF THE RECTIFIER, THE BATTERIES OF THE MEASURING INSTRUMENT MUST HAVE A VOLTAGE AT LEAST 6 VOLTS, BECAUSE OTHERWISE AN INFINITE RESISTANCE MIGHT BE SHOWN IN BOTH DIRECTIONS. D HIGH VOLTAGE CAPACITOR TEST CARRY OUT 3D CHECKS. A. Isolate the high voltage capacitor from the circuit. B. Continuity check must
TEST PROCEDURES (CONT'D) CARRY OUT 3D CHECKS. Disconnect the leads from the monitor resist. Using an ohmmeter and set on a low range. Check between the terminals of the monitor resistor. The resistance of monitor resistor is approx. 0.8 ohms. If incorrect readings are obtained, replace the monitor resistor. CARRY OUT 4R CHECKS. G MONITOR RESISTOR TEST CARRY OUT 3D CHECKS. Disconnect the leads from the motor. Usin
TEST PROCEDURES (CONT'D) PROCEDURE LETTER COMPONENT TEST 2-2 In connection with indicators a) At a certain digit, all or some segments do not light up. b) At a certain digit, brightness is low. c) Only one indicator does not light. d) The corresponding segments of all digits do not light up; or they continue to light up. e) Wrong figure appears. f) A certain group of indicators do not light up. g) The figure of all digits flicker. 2-3 Other pos
TEST PROCEDURES (CONT'D) PROCEDURE LETTER COMPONENT TEST RELAY SYMBOL OPERATIONAL VOLTAGE CONNECTED COMPONENTS RY1 APPROX. 25.0V D.C. Oven lamp / Turntable motor / Cooling fan motor RY2 APPROX. 25.0V D.C. Power transformer CARRY OUT 4R CHECKS. N PROCEDURES TO BE TAKEN WHEN THE FOIL PATTERN ON THE PRINTED WIRING BOARD (PWB) IS OPEN To protect the electronic circuits, this model is provided with a fine foil pattern added to the primary on the PWB,

TOUCH CONTROL PANEL ASSEMBLY

OUTLINE OF TOUCH CONTROL PANEL The touch control section consists of the following units as shown in the touch control panel circuit. (1) Key Unit (2) Control Unit The principal functions of these units and the signals com- municated among them are explained below. Key Unit The key unit is composed of a matrix, signals generated in the LSI are sent to the key unit through R10, R11, R12, R13, R20, R21 and R22. When a k

Sharp R-3A88 DESCRIPTION OF LSI

LSI(IZA683DR) The I/O signal of the LSI(IZA683DR) are detailed in the following table. Pin No. Signal I/O Description 1 Vdisp IN Anode (segment) of Fluorescent Display light-up voltage: -34V Vp voltage of power source circuit input. 2 R00 IN Signal coming from touch key. When either one of G12 line keys on key matrix is touched, a corresponding signal out of R10 - R13, R20, R21 and R22 will be input into R00. When no key is tou

Signal to sound buzzer.

A: key touch sound (0.12 sec.). B: Completion sound (2.4 sec.). 26-27 D4-D5 OUT Segment data signal. Refer to the touch control panel circuit for the relationship between signals and indicators. Normally, one pulse is output in every synchronized signal period, and input to the anode of the fluorescent display. 28 D6 OUT Segment data signal. Signal similar to P41. Key strobe signa

Sharp Microwave Oven Owners Instructions: