Sharp R-419CK Supplemental Service Manual

Text of Sharp R-419CK Supplemental Service Manual

Sharp R-419CK In the interest of user-safety the oven should be restored to its original

condition and only parts identical to those specified should be used. WARNING TO SERVICE PERSONNEL: Microwave ovens con- tain circuitry capable of producing very high voltage and current, contact with following parts may result in a severe, possibly fatal, electrical shock. (High Voltage Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Recti- fier Assembly,

PRECAUTIONS TO BE OBSERVED BEFORE AND

DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY (a) Do not operate or allow the oven to be operated with the door open. (b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary: (1) interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and other damage),

WARNING TO SERVICE PERSONNEL

Microwave ovens contain circuitry capable of pro- ducing very high voltage and current, contact with following parts may result in a severe, possibly fatal, electrical shock. (Example) High Voltage Capacitor, High Voltage Power Trans- former, Magnetron, High Voltage Rectifier Assem- bly, High Voltage Harness etc.. Read the Service Manual carefully and follow all instructions. Before Servicing 1. Disconnect the power

MICROWAVE MEASUREMENT PROCEDURE

A. Requirements: 1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven should not exceed 1mW/cm2 at any point 5cm or more from the external surface of the oven, measured prior to acquisition by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2 at any point 5cm or more from the external surface of the oven. 2) Safety interlock

SHARP ELECTRONICS CORPORATION

SHARP PLAZA, MAHWAH, NEW JERSEY 07430-2135 SERVICE MANUAL MICROWAVE OVEN R-419CK FOREWORD This Manual has been prepared to provide Sharp Electronics Corp. Service Personnel with Operation and Service Information for the SHARP MICROWAVE OVEN, R-419CK. It is recommended that service personnel carefully study the entire text of this manual so that they will be qualified to render satisfactory customer service. Check the

120 Volts / 13.3 Amperes/1550Watts

60 Hertz Single phase, 3 wire grounded Power Output 1100 watts (IEC-705 TEST PROCEDURE) Operating frequency of 2450MHz Case Dimensions Width 21-11/16" Height 12-3/8" Depth 17-3/8" Cooking Cavity Dimensions Width 15" 1.4 Cubic Feet Height 9-7/16" Depth 16-3/4" Tray Size 14-1/8" Diameter Control Complement Touch Control System Clock ( 1:00 - 12:59 ) Timer (0 - 99

a qualified electrician and have it replaced with a properly grounded

three-pronged wall receptacle or have a grounding adapter properly grounded and polarized. If the extension cord must be used, it should be a 3-wire, 15 amp. or higher rated cord. Do not drape over a countertop or table where it can be pulled on by children or tripped over accidentally. CAUTION: DO NOT UNDER ANY CIRCUMSTANCES CUT OR RE- MOVE THE ROUND GROUNDING PRONG FROM THIS

SENSOR COOKING CONDITION

Using the SENSOR function, food is cooked without figuring time, power level or quantity. When the oven senses enough steam from the food, it relays the information to its microprocessor which will calculate the remaining cooking time and power level needed for best results. When the food is cooked, water vapor is developed. The sensor "senses" the vapour and its resistance increase gradually. When the resistance rea

Figure O-2 Oven Schematic - Cooking Condition

Figure O-1 Oven Schematic - Off Condition SCHEMATIC NOTE: CONDITION OF OVEN 1. Door Closed 2. CLOCK APPEARS ON DISPLAY 120V AC 60 Hz OVEN LAMP TURN- TABLE MOTOR FAN MOTOR MONITOR SWITCH H.V. RECTIFIER MAGNETRON SECONDARY INTERLOCK SWITCH TTM OL FM CAVITY TEMP. FUSE A1 A2 COM. COM. COM. N.O. N.C. N.O. DOOR SENSING SWITCH (RY-1) (RY-2) CONTROL UNIT PRIMARY INTERLOCK RELAY B1 B2 GRN POWER TRANSFORMER MO

Sharp R-419CK 6. Re-install the outer case (cabinet).

7. Reconnect the power supply cord after the outer case is installed. 8. Run the oven and check all functions. TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST Key Unit 5 4 3 2 1 0 9 8 7 6 START BEVERAGE POPCORN Power Level MINUTE PLUS Fresh Rolls/ muffins Frozen entrees CUSTOM HELP Ground Meat (SENSOR COOK) Stop Clear Fresh vegetables G 8 G 9 G10 G11 G12 G13 G1

Checking the initial sensor cooking condition

Warning: The oven should be fully assembled before following procedure. 1) The oven should be plugged in at least two minutes before sensor cooking. 2) Room temperature should not exceed 95OF(35OC). 3) The unit should not be installed in any area where heat and steam are generated. The unit should not be installed for example, next to conventional surfa

CHECKING CONTROL UNIT

(1) Disconnect the power supply cord, and then remove outer case. (2) Open the door and block it open. (3) Discharge high voltage capacitor. (4) Disconnect the sensor connector that is mounted to control panel. (5) Then connect the dummy resistor circuit (see fig.) to the sensor connector of control panel. (6) Disconnect the leads to the primary of power transformer. (7) Ensure that these leads remain isolated from other c

Figure S-1. Pictorial Diagram

HIGH VOLTAGE CAPACITOR HIGH VOLTAGE WIRE A H.V. RECTIFIER POWER SUPPLY CORD 120V 60Hz HIGH VOLTAGE COMPONENTS OVEN LAMP AND SOCKET MAGNETRON COM. MONITOR SWITCH COM. N.O. COM. COM. N.O. N.O. N.C. DOOR SENSING SWITCH SECONDARY INTERLOCK SWITCH TURNTABLE MOTOR NOTE: Hot (ORG) wire must be connected to the terminal with blue mark on the oven light socket. POWER TR

Note: The parts marked “∆” may cause undue microwave exposure.

The parts marked “*” are used in voltage more than 250V. "§" MARK: PARTS DELIVERY SECTION. ELECTRIC PARTS 1- 1 RC-QZB018MRE0 M High voltage capacitor 1 AQ 1- 2 FH-DZB013MRY0 M High voltage rectifier assembly 1 AK 1- 3 QSOCLB006MRE0 M Oven lamp socket 1 AE 1- 4 RLMPTA068WRE0 M Oven lamp 1 AE 1- 5 RMOTEA346WRE0 M Fan

Oven cavity (Not a replaceable part)

1 -- 4- 9 PCOVPB073MRP0 M Waveguide cover 1 AC 4-10 PPACGB014MRF0 M Turntable motor packing 1 AA 4-11 PDUC-B101MRP0 M AH sensor duct 1 AF 4-12 PCUSGB033MRP0 M Cushion 1 AA 4-13 PCUSGB028MRP0 M Cushion 1 AA DOOR PARTS 5 -1 FCOV-B154MRK0 M Door frame assembly [R-420CK]

Sharp R-419CK OVEN AND CABINET PARTS

2-3 4-7 6-7 1-5 4-6 4-8 4-9 6-5 6-4 2-1 7-6 1-12 4-10 7-2 7-2 7-5 4-3 1-13 7-3 7-6 1-9 7-8 7-8 4-2 7-5 1-11 1-3 1-4 7-4 1-8 1-8 4-4 7-1 4-1 1-1 1-2 2-2 2-2 2-2 2-2 7-5 7-5 4-12 7-5 6-6 1-7 1-6 4-5 1-14 7-7 7-7 7-9 7-9 7-10 4-13

Sharp Microwave Oven Owners Instructions: