Sharp R-480J Service Manual

Text of Sharp R-480J Service Manual

TABLE OF CONTENTS

Page CAUTION, MICROWAVE RADIATION............................................................................................................. 1 WARNING..........................................................................................................................................................1 PRODUCT SPECIFICATIONS ........................................................................................................

Sharp R-480J GENERAL IMPORTANT INFORMATION

This Manual has been prepared to provide Sharp Corp. Service engineers with Operation and Service Information. It is recommended that service engineers carefully study the entire text of this manual, so they will be qualified to render satisfactory customer service. CAUTION MICROWAVE RADIATION DO NOT BECOME EXPOSED TO RADIATION FROM THE MICROWAVE GENERATOR OR OTHER PARTS CONDUCTING

Sharp R-480J 230 - 240 Volts

50 Hertz Single phase, 3 wire earthed Power Consumption 1.65 kW Power Output 1200 watts nominal of RF microwave energy (IEC Test Procedure) Operating frequency 2450 MHz Case Dimensions Width 550 mm Height 315 mm Depth 446 mm Turntable diameter 360mm Control Complement Touch Control System Clock ( 1:00 - 12:59) Timer (0 - 99 minutes 99 seconds) Microwave Power for Variable

1. Ventilation openings

2. Oven lamp 3. Door hinges 4. Door safety latches 5. See through door 6. Door seals and sealing surfaces 7. Coupling 8. Door open button 9. Touch control panel 10.Digital readout 11.Waveguide cover 12.Power supply cord 13.Rating label 14.Menu label 15.Turntable 16.Roller stay 10 3 4 2 7 13 5 6 14 4 11 8 16 9 12 15 1 TOUCH CONTROL PANEL NOTE: Some one-touch cooking features such as "Instant Cook" are disable

because the relay (RY1) stays closed. Shown in the

display is the remaining time. 6. MONITOR SWITCH CIRCUIT The monitor switch is mechanically controlled by oven door, and monitors the operation of the 1st. latch switch and 2nd. interlock relay. 6-1 When the oven door is opened during or after the cycle of a cooking program, the 1st. latch switch and 2nd. interlock relay control switch must open their contacts first. After that

2. Heat potatoes. Moisture and humidity is emitted rapidly.

You can smell the aroma as it cooks. 3. Sensor detects moisture and humidity and calculates cooking time and variable power. Cooking Sequence. 1. Touch each SENSOR COOK or SENSOR INSTANT REHEAT function pad to operating the sensor cooking. Refer to the operation manual for the proper procedure. NOTE: The oven should not be operated on SENSOR COOK or SENSOR INSTANT REHEAT immediately afte

Figure D-1. Door Open Mechanism

1ST. LATCH SWITCH AND 2ND. INTERLOCK RE- LAY CONTROL SWITCH 1. When the oven door is closed, the contacts (COM-NO) must be closed. 2. When the oven door is opened, the contacts (COM- NO) must be opened. MONITOR SWITCH 1. When the oven door is closed, the contacts (COM-NC) must be opened. 2. When the oven door is opened, the contacts (COM- NC) must be closed. 3. If the oven door is opened and the contacts (COM-NO) of

Sharp R-480J Microwave ovens contain circuitry capable of pro-

ducing very high voltage and current, contact with any part of the high voltage circuit will result in electrocution. High voltage capacitor, Power trans- former, Magnetron, High voltage rectifier assem- bly, High voltage fuse, High voltage harness. REMEMBER TO CHECK 3D 1) Disconnect the supply. 2) Door opened, and wedged open. 3) Discharge high voltage capacitor. WARNING: AGAINST THE C

CK = Check / RE = Replace

Home fuse blows when power supply cord is plugged into wall outlet. FUSE F10A blows when power supply cord is plugged into wall outlet. Display does not show anything when power supply cord is plugged into wall outlet. Display does not operate properly when STOP/CLEAR pad is touched. Oven lamp does not light at door opened. (Display appears.) Oven does not start when the START pad is touched. (Display appears) Oven lamp

NEVER TOUCH ANY PART IN THE CIRCUIT WITH YOUR HAND OR AN INSULATED TOOL

WHILE THE OVEN IS IN OPERATION. CARRY OUT 3D CHECK. Isolate the magnetron from high voltage circuit by removing all leads connected to filament terminal. To test for an open circuit filament use an ohmmeter to make a continuity test between the magnetron filament terminals, the meter should show a reading of less

HIGH VOLTAGE CAPACITOR TEST

TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST Room temperature .................. To = 21˚C Initial temperature ................. T1 = 11°C Temperature after (35 + 3) = 38 sec. ................................................................ T2 = 21°C Temperature difference Cold-Warm (∆T = T2 - T1) ......................................... ∆T = 10°C Measured output power The equation is “P = 120 x ∆T�

B. Continuity check must be carried out with measuring instrument which is set to the highest resistance

range. C. A normal capacitor shows continuity for a short time (kick) and then a resistance of about 10MΩ after it has been charged. D. A short-circuited capacitor shows continuity all the time. E. An open capacitor constantly shows a resistance about 10 MΩ because of its internal 10MΩ resi

TOUCH CONTROL PANEL ASSEMBLY TEST

TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST H MOTOR WINDING TEST CARRY OUT 3D CHECKS. Disconnect the leads from the motor. Using an ohmmeter, check the resistance between the two terminals as described in the table below. Table: Resistance of Motor Motors Resistance Fan motor Approximately 250 Ω Turntable motor Approximately 14.5 kΩ If incorrect readings are obtained, replace the motor. CARRY OUT 4R CH

b) At a certain digit, brightness is low.

c) Only one indicator does not light. d) The corresponding segments of all digits do not light up; or they continue to light up. e) Wrong figure appears. f) A certain group of indicators do not light up. g) The figure of all digits flicker. 2-3 Other possible troubles caused by defective control unit. a) Buzzer does not sound or continues to sound. b) Clock

Checking the initial sensor cooking condition

WARNING : The oven should be fully assembled before following procedure. (1) The oven should be plugged in at least two minutes before sensor cooking. (2) Room temperature should not exceed 35˚C. (3) The unit should not be installed in any area where heat and steam are generated. The unit should not be installed, for example, next to a conventional surf

TESTING METHOD FOR AH SENSOR AND/OR CONTROL UNIT

To determine if the sensor is defective, the simplest method is to replace it with a new replacement sensor. (1) Disconnect the power supply cord, and then remove outer case. (2) Open the door and block it open. (3) Discharge high voltage capacitor. (4) Remove the AH sensor. (5) Install the new AH sensor. (6) Reconnect all leads removed from component

TOUCH CONTROL PANEL ASSEMBLY

OUTLINE OF TOUCH CONTROL PANEL The touch control section consists of the following units. (1) Key Unit (2) Control Unit (The Control Unit consists of Power Unit and LSI Unit). The principal functions of these units and the signals communicated among them are explained below. Key Unit The key unit is composed of a matrix, signals generated in the LSI are sent to the key unit through P00-P07. When a key pad is touched,

The I/O signal of the LSI is detailed in the following table.

Pin No. Signal I/O Description 1 COM5 OUT Common data signal : COM11. Connected to LCD signal COM11. 2 COM4 OUT Common data signal : COM12. Connected to LCD signal COM12. 3 COM3 OUT Common data signal : COM13. Connected to LCD signal COM13. 4 COM2 OUT Common data signal : COM14. Connected to LCD signal COM14. 5 COM1 OUT Common data signal : COM15. Connected to LCD signal COM15. 6 C

Key strobe signal.

Signal applied to touch-key section. A pulse signal is input to AIN7, P14, P15, P16 and P17 terminal while one of G3 line keys on key matrix is touched. 38 P04 OUT Key strobe signal. Signal applied to touch-key section. A pulse signal is input to AIN7, P14, P15, P16, P17 and AIN6 terminal while one of G4 line keys on key matrix is touched. 39 P03 OUT Key strobe signal. Signal applied to touch-key section. A pulse sig

Sharp Microwave Oven Owners Instructions: