Sharp R-4A10 Service Manual

Text of Sharp R-4A10 Service Manual

In the interests of user-safety the set should be restored to its original

condition and only parts identical to those specified should be used. (RDlGlOlU) TABLE OF CONTENTS Page FOREWORD ....................................................................................................................................................... 1

3 _ _

=--k-Pug *: 3 *x- 1.: 7-e _ _, .:ss . . ^ . - . .- ---...--w.z-~_ -.‘.~ .-.-. ~ II --.--be-_ Photo R-4A20 Photo RQA30

This Manual has been prepared to provide Sharp Corp.

Service Personnel with complete Operation and Service information for the SHARP MICROWAVE ovens, R4A10/R4AZ0/R4A30. It is recommended that service personnel carefully study the entire text of this manual so they will be qualified to render satisfactory customer service. Check interlock switches and door seal carefully. Special at- tention should be given to av

The Sharp Microwave

Oven uses microwave energy to produce heat in the food to be cooked. Unlike con- ventional ovens microwave energy will cook foods without applying external heat. Microwaves, which are short electromagnetic waves of RF (radio frequency) energy, pass through materials such as glass, paper, china and most plastics. Materi- als such as metal and aluminum foil tend to reflect microwaves an

1. Ventilation openings

7. Door latches 2. Oven lamp 8. Door button open 3. Oven door with see through window 9. Touch Control Panel 4. Removable turntable 10. Digital readout 5. Roller Stay 11. Waveguide cover 6. Hinges 12. Access cover for oven lamp replacement Touch Control Panel AUTO COOK MENUS AUTO COOK Touch to select Auto Cook mode. EASY REHEAT PAD Touch to select Easy Reheat mode. L EASY REHEAT MENUS EASY DEFROST PAD Touch to defrost m

is a description of component functions

during oven operation. (RD71101 U) OFF CONDITION Closing the door activates both door latch switches: upper latch switch and lower latch switch. (in this condition, the monitor switch contacts are opened.) The stop switch is activated by the latch head. When oven is plugged in, 240 volts A.C. is supplied to the control unit. But no components in the o

1 DOOR CLOSED

2 CLOCK APPEARS ON DISPLAY Fuss MS.3A SWITCH TURNTABLE MOTOR l-L=& --- Jr--+ I T -e.- I a-- T I M v RECTIFIER L------A MAGNETRON . SCHEMATIC I I CONTROL HIGH 4 START PAD TOUCHED NOTE: CONDITION OF OVEf 1 DOOR CLOSED 2 COOKING TIME PROGRAMMED 3 VARIABLE COOKING I I s-a I - 1 k&i~ 1 UNIT CONTROL i ‘a2 45- 83 e-v h- , M V RECTIFIER Lam-’ MAGNETRON N I Figure. 0- 1, Oven Schemat

The switch is activated by the upper latch head on the

door while the door is closed. When the door is opened, the switch interrupts the circuit (except oven lamp). LOWER LATCH SWITCH The switch is activated by the lower latch head on the door. When the door is opened, the switch interrupts the circuit to transformer. A cook cycle cannot take place until the door is firmly closed and the

When troubleshooting the microwave oven, it is helpful to

follow the Sequence of Operation in performing the checks. Many of the possible causes of trouble will require that a specific test be performed. These tests are given a procedure letter which will be found in the “Test Procedures section.” IMPORTANT: If the oven becomes inoperative because of a blown fuse in the monitor-upper latch switch circuit, c

Sharp R-4A10 Oven lamp does not light at ail.

I Burned out bulb. I Replace oven lamp. 1 I Open wiring to oven lamp socket. I Check and repair wiring. -1 Cook indicator appears in display but turntaMe motor does not operate. Defective relay RY-1 on control unit. Turntable motor defective. Open or loose wiring between control unit and mo

TEST PROCEDURE OR

CORRECTION EASY DEFROST condition touching INSTANT COOK/START Pad, “ERROR” appears. Programmed incorrectly EASY DEFROST will only operate on a specificweight. Range for each food category. See steps for Easy Defrost is Operation Manual. Defective control unit. Procedure I - 9

THE HIGH VOLTAGE

CAPACITOR BEFORE TOUCHING ANY OVEN COMPO- NENTS OR WIRING. To test for an open filament, isolate the magnetron from the high voltage circuit. A continuity check across the magnetron filament leads should indicate less than 1 “ohm. To test for a shorted magnetron, connect the ohmmeter leads between the magnetron filament leads and chassis g

4. Room temperature should be around 20 “C.

5. Power supply voltage should be specification voltage. B POWER TRANSFORMER TEST DISCHARGE THE HIGH VOLTAGE CAPACITAOR BEFORE TOUCHING ANY OVEN COMPO- NENTS OR WIRING. Disconnect the primary input terminals and measure the resistance of the transformer with an ohmmeter. Check for continuity of the coils with an ohmmeter. On the R x 1

check across the temp. fuse terminals should indicate a closed circuit uniess the

temperature of the temp. fuse reaches approximately 145 “C. An open magnetron temp. fuse indicates overheating of the magnetron assembly. If the temp. fuse indicates a open circuit, replace the temp. fuse and check for restricted air flow to the mag

The touch control panel consists of circuits including

semiconductors such as LSI, ICs, etc. Therefore, unlike conventional microwave ovens, proper maintenance cannot be performed with only a voltmeter and ohmmeter. in this service manual, the touch control panel assembly is di- vided into two units Control Unit and Key Unit and troubleshooting by unit

Sharp R-4A10 The touch control section consists of the following

units as shown in the touch control panel circuit. (1) Key Unit (2) Control Unit The principal functions of these units and the signals communicated among them are explained below. (RD911 A3U) Key Unit The key unit is composed of a matrix, signals generated in the LSI are sent to the kev unit through SO-S6. When a key pad is touched,

Sharp R-4A10 The I/O signal of the LSI(IZAf74DR)

is detailed in the following table. (RD93101 U) PIN NO. 1 1 1 SIGNAL j T I I/O 1 OUT Sianal to sound buzzer. A: Key touch sound (0.1 sec.). B: Completion sound (2.0 sec.). (RD93LAl U) PIN NO. / 2 1 SIGNAL j VDD Power source voltage: -12V. VDD voltage of power source circuit input. I I/O i IN (RD93GAl U) PIN NO. 1 3 i SIGNAL t VREF I l/O ! IN Reference voltaqe input terminal.

Sharp Microwave Oven Owners Instructions: