Sharp R-9H58 Service Manual

Text of Sharp R-9H58 Service Manual

Sharp R-9H58 TABLE OF CONTENTS

Page CAUTION, MICROWAVE RADIATION ............................................................................................................. 1 WARNING ...........................................................................................................................................................1 PRODUCT SPECIFICATIONS.....................................................................................................

GENERAL IMPORTANT INFORMATION

This Manual has been prepared to provide Sharp Corp. Service engineers with Operation and Service Information. It is recommended that service engineers carefully study the entire text of this manual, so they will be qualified to render satisfactory customer service. CAUTION MICROWAVE RADIATION DO NOT BECOME EXPOSED TO RADIATION FROM THE MICROWAVE GENERATOR OR OTHER PARTS

230 - 240 Volts

50 Hertz Single phase, 3 wire earthed Power Consumption 1500 W (Microwave) 1600 W (Convection) Power Output 850 watts (IEC-705-1988 ) Operating frequency of 2450MHz Convection heater 1500 W Case Dimensions Width 627mm Height 378mm Depth 483mm Cooking Cavity Dimensions Width 410mm Height 245mm Depth 410mm Control Complement Touch Control System Clock ( 1:00 - 12:59) Timer

Sharp R-9H58 1. Ventilation opening

2. Oven lamp 3. Door hinges 4. Door safety latches 5. See through door 6. Door seal and sealing surfaces 7. Door open button 8. Touch control panel 9. Digital readout 10. Wave guide cover 11. Coupling 12. Access cover for oven lamp replacement 13. Menu label 14. Rating label 15. low rack 16. High rack TOUCH CONTROL PANEL 15 16 3 4 4 11 7 9 8 5 2 13 1 12 10 6 14 HELP MULTI COOK REHEAT SENSOR SENSOR INSTANT ACT

The following is a description of component functions

during oven operation. Relay and Components Connection RELAY CONNECTED COMPONENT RY1 Oven lamp/ Turntable motor RY2 Power transformer RY3 Convection heater RY4 Damper motor RY5 Convection motor RY6 Fan motor OFF CONDITION Closing the door activates all door interlock switches: upper latch switch, lower latch switch and stop switch. (In this condition, the monitor switch contacts are closed.) Wh

unit de-energizing the relay (RY4) and opening the

circuit to the damper motor. 3. The coil of heater relay (RY3) is energized by the CPU unit and the main supply voltage is added to the convection heater. 4. When the oven temperature reaches the selected preheat temperature, the following operations occur: 4-1. The heater relay (RY3) is de-energized by the CPU unit temperature circuit and thermistor, opening the circuit to the convection heater.

Sharp R-9H58 2. Heat potatoes. Moisture and humidity is emitted rapidly.

You can smell the aroma as it cooks. ; MICROWAVE AH SENSOR 3. Sensor detects moisture and humidity and calculates cooking time and variable power. AH SENSOR COOKING SEQUENCE 1. In case the AH sensor cooking condition is started, the coil of shut-off relays (RY1+RY6) are energized, the oven lamp and cooling fan motor are turned on, but the power transformer is not turned on. NOTE

UPPER AND LOWER LATCH SWITCHES

Those latch switches are mounted in the latch hooks as shown in figure. They are activated by the latch heads on the door. When the door is opened, the switches interrupt the circuit to all components except CPU unit and relay unit and oven lamp. A cook cycle cannot take place until the door is firmly closed thereby activating both interlock switches. LATCH HOOK STOP SWITCH MONITOR SWITCH SWITCH LEVER OPEN LEVER LATC

Sharp R-9H58 2. The fuse also blows when upper latch switch and

lower latch switch remain closed with the oven door open and when the monitor switch closes. 3. The fuse M8A also blows when asymmetric rectifier, H.V. rectifier, H.V. wire harness, H.V. capacitor, magnetron or secondary winding of power transformer is shorted. ASYMMETRIC RECTIFIER The asymmetric rectifier is a solid state device that prevents current flow ins both directions. And it prevents the

It is then exhausted at the top of the oven cavity into a

condensation compartment. Convection Cooking: Damper is in the closed position, so that no hot air will be allowed to leak out the oven cavity. Damper Operation 1. When power supply cord is plugged in: 1-1. When power supply cord is plugged in, a signal is sensed in the control unit, and operates shut-off relay (RY4). 1-2. Contacts of shut-off relay (RY4) close, the damper motor is energize

WARNING TO SERVICE PERSONNEL

Microwave ovens contain circuitry capable of producing very high voltage and current, contact with any part of the high voltage circuit will result in electrocution. High voltage capacitor, Power transformer, Magnetron, High voltage rectifier assembly, High voltage harness. REMEMBER TO CHECK 4R 1) Reconnect all leads removed from components during testing. 2) Replace the outer case (cabinet). 3) Reconnect

Home fuse blows when

power supply cord is plugged into wall outlet. Fuse M8A blows when power cord is plugged into wall out- let. Display does not show any- thing when power cord is first plugged into wall outlet. Display does not operate properly when STOP/ CLEAR pad is touched. (The time of day should appear on the display with beep sound during normal condition.) Oven lamp does not light with door opened. Oven lamp does not light at all Oven l

NEVER TOUCH ANY PART IN THE CIRCUIT WITH YOUR HAND OR AN INSULATED TOOL

WHILE THE OVEN IS IN OPERATION. CARRY OUT 3D CHECK. Isolate the magnetron from high voltage circuit by removing all leads connected to filament terminal. To test for an open circuit filament use an ohmmeter to make a continuity test between the magnetron filament terminals, the meter should show a reading of les

Initial temperature............................................................................................. T1 = 11°C

Temperature after (49 + 2) = 51 sec................................................................. T2 = 21°C Temperature difference Cold-Warm ............................................................... ∆T1 = 10°C Measured output power The equation is “P = 85 x �

rectifier, high voltage wire or filament winding of the power transformer is shorted.

CARRY OUT 4R CHECKS. NOTE: FOR MEASUREMENT OF THE RESISTANCE OF THE RECTIFIER, THE BATTERIES OF THE MEASURING INSTRUMENT MUST HAVE A VOLTAGE AT LEAST 6 VOLTS, BECAUSE OTHERWISE AN INFINITE RESISTANCE MIGHT BE SHOWN IN BOTH DIRECTIONS. CARRY OUT 3D CHECKS. A. Isolate the high voltage capacitor from the circuit. B. C

CARRY OUT 3D CHECKS.

Disconnect connector-E from the CPU unit. Measure the resistance of the thermistor with an ohmmeter. Connect the ohmmeter leads to Pin No’s E-3 and E-4 of the thermistor harness. Room Temp. .................. 20˚C - 30˚C Resistance ..................... Approx. 350kΩ - 155kΩ If the meter does not indicate above resistance, replace the thermistor. CARRY OUT 4R CHECKS. I T

If incorrect readings are obtained, replace the motor.

CARRY OUT 4R CHECKS. CARRY OUT 3D CHECKS. Disconnect the leads from the monitor resist. Using an ohmmeter and set on a low range. Check between the terminals of the monitor resistor. The resistance of monitor resistor is approx. 0.8 ohms. If incorrect readings are obtained, replace the monitor resistor. CARRY OUT 4R CHECKS. The touch control p

Sharp Microwave Oven Owners Instructions: