Rockford Fosgate 100X2 Owner's Manual

amplifiers. At Rockford Fosgate we are committed to musical reproduction at its best, and we are pleased you chose our product. Through years of engineer- ing expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve. For maximum performance we recommend yo ...

Specifications ................................................................................... 1 Punch Accessory Pack .................................................................... 3 Introduction ...................................................................................... 4 Notes on Internal Circuitry........................................................... 4 Controls and Features..................................... ...

Dynamic Power Rating (IHF-202 Standard) - Measured at 14.4 Volts1 Mono into a 4Ω Load 160 Watts 260 Watts 420 Watts 500 Watts Per channel into a 2Ω Load 75 Watts 130 Watts 200 Watts 240 Watts Per channel into a 4Ω Load 40 Watts 80 Watts 110 Watts 150 Watts Continuous Power Rating (IASCA Standard) - Measured at 11.6 Battery Volts RMS continuous power per channel, both channels dr ...

PUNCH 100DSM PUNCH 200DSM Dimensions 9-5/8" (24.4cm) W 9-5/8" (24.4cm) W 9-5/8" (24.4cm) W 9-5/8" (24.4cm) W 9-5/8" (24.4cm) L 10-5/8" (27.0cm) L 11-5/8" (29.5cm) L 12-5/8" (32.0cm) L 2-5/8" ( 6.6cm) H 2-5/8" ( 6.6cm) H 2-5/8" ( 6.6cm) H 2-5/8" ( 6.6cm) H Bandwidth 15Hz to 100kHz ±3dB Damping Factor @ 4Ω At output connector - Over 200 Frequency Response 20Hz to 20kHz ±1.0dB / 10Hz to 100kHz ±3dB Slew Factor Ov ...

3 17' (518.16cm) Red Power Wire Punch Owner's Manual Punch Verification Certificate Power Fuse Holder with Fuse for Punch 40, 60, and 100 Power Fuse Holder with fuse for Punch 200 Hex Head and Mounting Screws Remote Turn-on Wire Connector Plug Power Ring Terminals 12' (365.76cm) Blue Remote Turn-on Wire 1.5' (45.72cm) Black Grounding Wire ...

lation, and operation of the Punch 2-channel Amplifiers. We suggest you save this manual for future reference. We strongly recommend you have your Authorized Rock- ford Fosgate Dealer and Service Center install the new Punch amplifier. If you do choose to install the amplifier yourself, please be sure to read the entire manual before beginning. The Rockford Punch 40DSM, 60DSM, 100DSM ...

problem of power device reliability. In particular, load fault conditions can easily destroy an amplifier that is not carefully designed. Rockford Fosgate has answered this problem with the development of Real Time Power Pro- tection (RTPP). The RTPP circuits protect the Punch amplifiers by multi- plying output device voltage and current values to obtain approximate instantaneous device power. This ...

the Punch amplifiers. Top View of Amplifier and End Caps 6 CONTROLS AND FEATURES Punch Housing The cast aluminum heatsink of the Punch is designed for high performance cooling. The raised design of the hous- ing allows cables and wires to run underneath the unit. This provides for greater wiring flexibility and protects the cables from damage caused by excessive heat and bend- ing. Interchangeable ...

turn-on wire to the source unit’s “Accessory” or “Auto Antenna” lead, either of which will go to +12 volts when the source unit is turned on. The LED illuminates red when the unit is turned on. These connectors are used to supply power and ground to the amplifier and accept 12 AWG - 8 AWG wires.* 7 REM Connector LED Power Indicator B+/GND Power Connector Front View of Power Side B+/GND Connecto ...

8 These gold plated terminal blocks connect the Right and Left channel outputs to the speakers and accept wire sizes from 8 gauge through 18 gauge. Gold plated con- nectors are immune to corrosion that can cause signal deterioration. These controls adjust the amount of treble and bass response desired. To increase the amount of response, turn the dials clockwise; to decrease, turn the dials coun- terclockwise. These co ...

ations for installing your new Punch amplifier. Checking your battery and current sound system, as well as pre- planning your system layout and best wiring routes will save installation time. When deciding how to lay out your new system, be sure that each component will be easily accessible for making adjustments. Before beginning any installation, be sure to follow these s ...

or chassis, of the vehicle. The following is a list of tools you will need for installing the Punch amplifier: Allen Wrenches (7/64" & 3/32") Wire Strippers Battery Post Wrench Electric Hand Drill with assorted bits Voltmeter Wire Crimpers (i.e., Perfect Interface RT-KT1) Tools Needed BATTERY AND CHARGING Punch amplifiers will naturally put an extra load on your battery and charging system. We recomme ...

is a minimum of 1” (2.5cm) of air gap above the amplifer's heatsink. Vertical mounting is still the best, and under dash mount- ing is satisfactory as well. Caution! Be sure to avoid running the power wires near the input cabling antenna, power leads, sensi- tive equipment or harnesses. The power wires carry substantial c ...

is supplied with the fuse holder. 5. Repeat the above steps to connect the remainder of the red power wire to the other side of the fuse holder and route to the amplifier mounting location. Wiring the Power Connectors 1. Strip back approximately 3/8" (.95cm) of wire. 2. Insert the bared wire into the connector and crimp in place as shown in the following diagram. The gold B+ terminal must be connected ...

to the chassis of the vehicle with 12 gauge, or heavier, stranded wire. To prevent ground loops, we recommend you refrain from extending the ground wire beyond 18" (45.72cm) in any installation. The ends of the Power and Ground wires that are connected to the amplifier should be stripped back 5/8” (1.59cm). The Punch amplifiers are turned on by supplying positive (+) 12 volts to the REM terminal. U ...

configurations. This configuration enables you to: • Run a single woofer in a stereo system • Run two bridged amplifiers as a high power stereo system • Run one amplifier with a bridged mono woofer and another as a high-frequency stereo amp, etc. For more information refer to the wiring diagrams begin- ning on page 17. Caution! Punch amplifiers are not recommended for impedance loads below 2Ω stereo ...

increases as the number of components in the filter increases. This means that a complex filter with a number of parts will stop the unwanted frequencies faster than a simple filter. The amount of reduction is measured in dB per octave. The most common filters used in speaker crossovers, as stated above, are 6 dB per octave which uses one component per filter. Placing this filter in series with ...

6 dB/Octave High Pass 16 Freq. Hertz Speaker Impedance 80 4.1mH 1000µF 8.2mH 500µF 16mH 250µF 100 3.1mH 800µF 6.2mH 400µF 12mH 200µF 130 2.4mH 600µF 4.7mH 300µF 10mH 150µF 200 1.6mH 400µF 3.3mH 200µF 6.8mH 100µF 260 1.2mH 300µF 2.4mH 150µF 4.7mH 75µF 400 .8mH 200µF 1.6mH 100µF 3.3mH 50µF 600 .5mH 136µF 1.0mH 68µF 2.0mH 33µF 800 .41mH 100µF .82mH 50µF 1.6mH 26µF 1000 .31mH 78µF .62mH 39µF 1.2mH 20µF 1200 .25mH ...

17 SOURCE UNIT L +OUT– TREBLE GAIN IN IN GAIN BASS +OUT– R B+ GND + – 8 OHM 8 OHM – + BRIDGED WOOFERS ...