Shure UP4 Operation & User’s Manual

Wireless System User Guide 27C8681 (Rev. 3) 2002, Shure Incorporated Printed in U.S.A. Patents 6, 296, 565; Des. 433, 642 ...

QUICK SETUP GUIDE FOR THE SHURE UP WIRELESS SYSTEM 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UP4 RECEIVER SETUP 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TRANSMITTER SETUP 1 . . . . . . . . . . . . ...

QUICK SETUP GUIDE FOR THE SHURE UP WIRELESS SYSTEM UP4 Receiver Setup and Camera Mounting To audio input To power supply (If not using interior battery power) FIGURE 1 ATTACHING THE MOUNTING BOX, INSTALLING THE UP4 RECEIVER 1. Open the battery compartment on the UP4 receiver and insert a fresh 9 volt battery if battery power is to ...

UC1 UC2 UP4 UP WIRELESS SYSTEM COMPONENTS FIGURE 2 U2 U1 SYSTEM DESCRIPTION The Shure UP Wireless System is a portable, frequency-agile, diversity wireless system operating in the UHF band. The UP4 receiver is easily mounted to a Sony
video camera or any video camera with an Anton-Bauer
battery pack. The UP4 is compatible with b ...

UP4 RECEIVER CONTROLS AND INDICATORS FIGURE 3 1 2 3 4 5 6 7 8 9 10 11 UP4 RECEIVER FEATURES 1. Group Setting Control. Rotate this switch clockwise to advance the Group setting, or rotate it counterclockwise to decrease the setting. Use the supplied screwdriver to make adjustments. 2. Channel Setting Control. Rotate this switch cloc ...

1 2 3 4 6 7 8 9 10 11 12 5 1 2 3 4 FIGURE 4 UC1 TRANSMITTER FEATURES AND CONTROLS 1. Antenna. A flexible 1/4 wave whip antenna is permanently attached to the top of the UC1 Body-Pack transmitter. 2. Power/Battery Fuel Gauge. When the Power switch is in the ON position, one of the three LEDs will glow, indicating that the transmitter ...

ON OFF 1 FIGURE 6 10 11 12 13 2 3 4 5 1 9 8 7 6 U1 TRANSMITTER CONTROLS & INDICATORS 1. Antenna. A 1/4 wave antenna is permanently attached to the top of the U1 body-pack transmitter. The antenna can be replaced in the field by a qualified technician. 2. Programmable Display. This display provides information on group and channel se ...

CHECKING BATTERIES UP4 Receiver 1. Turn the receiver power ON/OFF switch to the ON position. 2. Observe the PWR LED on front panel (See figure 8). If it is glowing red, the battery power is low and the battery should be changed immediately. FIGURE 8 PWR LED (Red Indicates Low Receiver Battery) UC1 and UC2 Transmitter 1. Turn the tra ...

INSTALLING BATTERIES UP4 Receiver Á FIGURE 11 1. Locate the battery door on the bottom of the unit. Release the battery door by sliding the door in the direction of the arrow until the pins on either side of the door are visible. Flip open the battery door once it is released. 2. Insert a fresh 9 volt battery, with terminals facing ...

CHANGING GROUP AND CHANNEL SETTINGS IMPORTANT: Transmitter GROUP and CHANNEL settings must match receiver GROUP and CHANNEL settings. Changing the UP4 Receiver Group/Channel Setting FIGURE 14 GROUP CHANNEL 1. To advance the receiver Group or Channel setting, rotate the appropriate switch clockwise, using the supplied screwdriver. Ro ...