RuggedCom RUGGEDSWITCH RS900G Hardware Installation Manual

Copyright © 2013 RuggedCom Inc. All Rights Reserved Dissemination or reproduction of this document, or evaluation and communication of its contents, is not authorized except where expressly permitted. Violations are liable for damages. All rights are reserved, particularly for the purposes of patent application or trademark registration. This document contains proprietary information, which is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without the prior written consent of RuggedCom I ...

Table of Contents FCC Statement And Cautions ................................................................................................... 6 1. Product Overview ................................................................................................................... 7 1.1. RS900G Front Panel ................................................................................................... 9 1.2. RS900G Bottom Panel ................................................................................................ 9 2. Installation ..................... ...

List of Figures 1.1. RS900G Front Panel .......................................................................................................... 9 1.2. RS900G Bottom Panel ....................................................................................................... 9 2.1. DIN Rail Mounting ............................................................................................................ 10 2.2. Power Supply Inputs ......................................................................................................... 11 2.3. DC Power Supply ...

List of Tables 1.1. RS900G Front Panel LED Definitions ................................................................................ 9 2.1. RS232 Female DCE Pinout .............................................................................................. 14 2.2. RJ45 Ethernet Pin Assignment ......................................................................................... 15 3.1. Operating Environment ..................................................................................................... 16 3.2. RS900G Power Supply Specifications ....... ...

RuggedCom® RuggedSwitch™ 6 RS900G Installation Guide Rev 107 FCC Statement And Cautions Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio com ...

RuggedCom® RuggedSwitch™ 7 RS900G Installation Guide Rev 107 1. Product Overview The RuggedSwitch™ RS900G is an industrially hardened, fully managed Ethernet switch providing dual fiber optical Gigabit Ethernet ports and eight Fast Ethernet copper ports. Designed to operate reliably in harsh industrial environments, the RS900G provides a high level of immunity to electromagnetic interference and heavy electrical surges typical of environments found in electric utility substations, factory floors or in curb side traffic control cabinets. An operating temperature range of -40°C to +85°C coupled with hazardous location certifica ...

RuggedCom® RuggedSwitch™ 8 RS900G Installation Guide Rev 107 Simple Plug and Play Operation • Automatic learning of up to 8192 MAC addresses • Auto-negotiation on all 10/100BaseTX ports • Auto-MDI/MDIX (crossover) on all 10/100BaseTX ports • LED indicators for link, activity and speed ROS™ Advanced Network Management • Enhanced Rapid Spanning Tree (eRSTPTM) • Quality of Service (802.1p) for real-time traffic • Port rate limiting: 128kbps to 8Mbps • VLAN (802.1q) with double tagging • IGMP Snooping for multicast filtering • Port configuration, status, statistics, mirroring, security • Loss of link managemen ...

RuggedCom® RuggedSwitch™ 9 RS900G Installation Guide Rev 107 1.1. RS900G Front Panel Figure 1.1. RS900G Front Panel LED Activity Description Solid Link Established LINK LED (Yellow) Blinking Tx/Rx Activity Power LED Solid Power On Alarm LED Solid Alarm condition exists Table 1.1. RS900G Front Panel LED Definitions 1.2. RS900G Bottom Panel Figure 1.2. RS900G Bottom Panel ...

2. Installation 2.1. DIN Rail Mounting An optional DIN rail mounting bracket is available for the RS900G. Figure 2.1. DIN Rail Mounting ...

2.2. Power Supply Wiring and Grounding 2.2.1. HI Power Supply Wiring and Grounding Figure 2.2. Power Supply Inputs The RS900G HI power supply inputs are connected as follows: 1. +/L should be connected to AC (Hot) 2. -/N should be connected to AC (Neutral) 3. Surge Ground is connected to the Chassis Ground via a braided cable or other appropriate grounding wire. Surge Ground is used as the ground conductor for all surge and transient suppression circuitry internal to the RS900G unit. 4. Chassis Ground should be connected to the AC Ground terminal 1. Equipment must be insta ...

2.2.2. DC Power Supply Wiring and Grounding Figure 2.3. DC Power Supply Wiring and Grounding The RS900G low voltage DC power supply features reverse polarity protection and dual independent inputs. This feature allows the connection of two DC sources with the same nominal voltage to provide redundant power supply inputs. The DC source must be connected to the DC inputs according to the polarity markings on the unit. 1. Equipment must be installed according to the applicable country wiring codes. 2. Surge Ground should be connected to Chassis Ground via a braided cable or o ...

2.3. HIPOT (Dielectric Strength) Testing Units which are to be “HIPOT” tested in the field must have the braided ground cable disconnected (see Figure 2.4, “HIPOT (Dielectric Strength) Testing”) during the HIPOT test. This is required in order to prevent the transient/surge suppression circuitry, which is connected to Surge Ground, from being activated during the HIPOT test. Figure 2.4. HIPOT (Dielectric Strength) Testing 2.4. Failsafe Output Wiring and Specifications The “Failsafe” output relay is provided to signal critical error conditions that may occur on ...

Figure 2.6. RS232 Female Connector Pin Signal 1 No Connection 2 Transmit Data 3 Receive Data 4 No Connection 5 Ground 6 No Connection 7 No Connection 8 No Connection 9 No Connection Table 2.1. RS232 Female DCE Pinout This port is not intended to be a permanent connection and the cable shall be less than 2m (6.5 ft) in length. ...

2.6. RJ45 Ports: Signal Description The RS900G has several 10/100BaseTX ports that allow connection to standard CAT-5 UTP cable with RJ45 male connectors. The RJ45 receptacles are directly connected to the chassis ground on the unit and can accept shielded CAT-5 cables. If shielded cables are used, care must be taken to ensure the shielded cables do not form a ground loop via the shield wire and the RJ45 receptacles at either end. Figure 2.7. RJ45 Port Connector RJ45 Pin 10/100Base-Tx 10/100/1000Base-Tx 1 RX+ A+ 2 RX- A- 3 TX+ B+ 4 NC C+ 5 NC C- 6 TX- B- 7 NC D+ 8 NC D- Ta ...

3. Specifications 3.1. Operating Environment Parameter Range Comments Ambient Operating Temperature -40 to 85°C Ambient Temperature as measured from a 30cm radius surrounding the center of the RS900G enclosure. Ambient Relative Humidity 5% to 95% Non-condensing Ambient Storage Temperature -40 to 85°C Operating Altitude 0 to 15240m (0 to 50000 ft) Over temperature range of -40 to 85°C Table 3.1. Operating Environment 3.2. Power Supply Specifications Power Supply Type Minimum Input Maximum Input Fuse Rating Isolation Maximum Power Consumption 12 – 24 VDC 10 VDC 36 VDC ...

3.5. Fiber Optic Port Specifications For maximum flexibility, RuggedCom Inc. offers a number of different transceiver choices for Gigabit fiber optic communications. The following table details fiber optic specifications based on the order code/transceiver selected at time of ordering. Order Code Mode / Connector Tx λ (nm) Cable Type 1. a Tx Pwr (dBm) (Min/Max) b Rx Sensitivity (dBm) b Rx Saturation (dBm) b Typical Distance (km) c 2LCMM MM / LC 850 50µ/125 -9.5 / -4 -20 0 0.5 2LC10 SM / LC 1310 9µ/125 -9.5 / -3 -22 -3 10 2LC25 SM / LC 1310 9µ/125 -5 / 0 -22 -3 25 2SC ...

3.6. Physical Dimensions Figure 3.1. RS900G Physical Dimensions Parameter Value Comments Dimensions 7.4 × 2.6 × 5.0 inches (187.96 × 66.04 × 127.0 mm) (Length × Width × Depth Weight 2.7 lbs (1.2 kg) Enclosure 20 AWG Galvanized Steel Table 3.6. Physical Specifications ...

3.7. Type Test Specifications 3.7.1. IEC 61850-3 Type Tests Test Description Test Levels Severity Levels Enclosure Contact +/- 8kV 4 IEC 61000-4-2 ESD Enclosure Air +/- 15kV 4 IEC 61000-4-3 Radiated RFI Enclosure ports 20 V/m x Signal ports +/- 4kV @ 2.5kHz x D.C. Power ports +/- 4kV 4 A.C. Power ports +/- 4kV 4 IEC 61000-4-4 Burst (Fast Transient) Earth ground ports +/- 4kV 4 Signal ports +/- 4kV line-to-earth, +/- 2kV line-to-line 4 D.C. Power ports +/- 2kV line-to-earth, +/- 1kV line-to-line 3 IEC 61000-4-5 Surge A.C. Power ports +/- 4kV line-to-earth, +/- 2kV line-to ...

3.7.2. IEEE 1613 Type Tests IEEE Test IEEE 1613 Clause Description Test Levels Enclosure Contact +/- 8kV C37.90.3 9 ESD Enclosure Air +/- 15kV C37.90.2 8 Radiated RFI Enclosure ports 35 V/m Signal ports +/- 4kV @ 2.5kHz D.C. Power ports +/- 4kV A.C. Power ports +/- 4kV C37.90.1 7 Fast Transient Earth ground ports +/- 4kV Signal ports 2.5kV common mode @ 1MHz D.C. Power ports 2.5kV common & differential mode @ 1MHz C37.90.1 7 Oscillatory A.C. Power ports 2.5kV common & differential mode @ 1MHz Signal ports 5 kV (Failsafe Relay) D.C. Power ports 5 kV C37.90 6 H.V. Impulse ...