Ryobi MS181 Operator's Manual

Text of Ryobi MS181 Operator's Manual

8-1/4 in. (209.6 mm) Cordless

Compound Miter Saw Model MS181 THANK YOU FOR BUYING A RYOBI CORDLESS COMPOUND MITER SAW. Your new saw has been engineered and manufactured to Ryobi's high standards for dependability, ease of operation, and operator safety. Properly cared for, it will give you

Table of Contents and Introduction .................................................................................................................. 2

■ Product Specifications...................................................................................................................................... 2 ■ Rules For Safe Operation .........................................................................................................

READ ALL INSTRUCTIONS

■ KNOW YOUR POWER TOOL. Read the operator's manual carefully. Learn the saw's applications and limitations as well as the specific potential hazards related to this tool. ■ GUARD AGAINST ELECTRICAL SHOCK BY PREVENTING BODY CONTACT WITH GROUNDED SURFACES. For example; pipes, radiators, ranges, refrigerator enclosures. ■ KEEP GUARDS IN PLACE and in good working order. ■ REMOVE ADJUSTING KEYS AND WRENCHES. Get in the habi

Ryobi MS181 NEVER LEAVE TOOL RUNNING UNAT-

TENDED. REMOVE BATTERY PACK. Do not leave tool, move workpiece or make adjustments until it comes to a complete stop. ■ FIRMLY CLAMP OR BOLT your miter saw to a workbench or table at approximately hip height. ■ USE ONLY CORRECT BLADES. Do not use blades with incorrect size holes. Never use blade washers or blade bolts that are defective or incorrect. The maximum blade capacity of your saw is 8-1/4 in. (209.6 mm

RULES FOR SAFE OPERATION

■ REPLACEMENT PARTS. All repairs, whether electrical or mechanical, should be made at your nearest authorized service center. ■ When servicing use only identical Ryobi replace- ment parts. Use of any other parts may create a hazard or cause product damage. ■ NEVER USE IN AN EXPLOSIVE ATMO- SPHERE. Normal sparking of the motor could ignite fumes. ■ NEVER leave the miter saw unattended while connected to a power sourc

IMPORTANT SAFETY INSTRUCTIONS FOR

CHARGER ■ SAVE THESE INSTRUCTIONS. This manual contains important safety and operating instructions for charger part number 1423701. ■ Before using charger, read all instructions and cautionary markings in this manual, on charger, and product using charger. ■ To reduce risk of injury, charge only nickel- cadmium type rechargeable batteries. Other types of batteries may burst causing personal injury and damage.

Frequency (cycles per second)

min Minutes Time Alternating Current Type or a characteristic of current --- Direct Current Type or a characteristic of current n0 No Load Speed Rotational speed, at no load .../min Revolutions or Reciprocation Per Minute Revolutions, strokes, surface speed, orbits etc. per minute Safety Alert Symbol Indicates danger, warning or caution. I

The shaft on which a blade or cutting tool is mounted.

Bevel Cut A cutting operation made with the blade at any angle other than 90° to the miter table. Crosscut A cutting or shaping operation made across the grain of the workpiece. Compound Miter Cut A compound miter cut is a cut made using a miter angle and a bevel angle at the same time. Freehand Performing a cut without using a fence, miter gage, fixture, work clamp, or other proper devic

Ryobi MS181 Your Compound Miter Saw has been shipped

completely assembled except for the battery pack, dust bag or dust guide. WARNING: If any parts are missing, do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. ■ Remove all loose parts from the carton. Separate and check with the list of loose parts. See Figure 1. ■ Remove the packing materials from around your saw. ■ Careful

Ryobi MS181 Carbide Tipped Saw Blade - 8-1/4 in. (209.6 mm)

■ Dust Bag ■ Dust Guide ■ Blade Wrench LOOSE PARTS LIST WARNING: The use of attachments or accessories not listed can or could be hazardous and cause serious personal injury. WORK CLAMP ■ Work clamp ■ 5 mm Hex Key ■ 6 mm Hex Key ■ Operator's Manual (Not Shown) The following items are included with your Compound Miter Saw: Fig. 2 SAW BLADE DUST GUIDE BLADE WRENCH 5 mm

LED FUNCTION OF CHARGER

See Figure 3. LED WILL BE LIGHTED TO INDICATE STATUS OF CHARGER AND BATTERY PACK: ■ Red LED lighted = Fast Charging Mode ■ Green LED lighted = Fully Charged Battery Pack ■ Yellow and Green LED Lighted = Control Charge or possible faulty battery. CHARGING BATTERY PACK The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it prior to use. N

KNOW YOUR COMPOUND MITER SAW

See Figure 5. Before attempting to use your saw, familiarize yourself with all operating features and safety requirements. WARNING: Do not allow familiarity with your saw to make you careless. Remember that a careless fraction

See Figure 6.

For convenience when carrying or transporting your miter saw from one place to another, a carrying handle has been provided on top of the saw arm as shown in figure 6. To transport saw, remove battery pack, then lower the saw arm and lock it in the down position. Lock saw arm by depressing the lock pin. Fig. 6 LOCK PIN SAW ARM LOCKED IN DOWN

DETENT STOPS ON MITER TABLE

Detent stops have been provided at 0°, 22-1/2°, 30°, and 45°. The 22-1/2°, 30° and 45° detent stops have been provided on both the left and right side of the miter table. BEVEL LOCK KNOB The bevel lock knob securely locks your compound miter saw at desired bevel angles. Positive stop adjustment screws have been provided on each side of the saw arm. These positive stop adjustment screws are for mak

See Figure 14.

■ Remove battery pack from saw. WARNING: Failure to remove battery pack from your saw could result in accidental starting causing possible serious personal injury. To install work clamp, place the shaft of the clamp in either hole in front of the miter table base. Rotate the knob on the clamp to move it in or out as needed. 4 5 3 0 3 0 1515 15 30 45 22.5 31.62 22.5 22.5 31.62 31.62 4 3 0 22.5 31.62 R O T A T I O N 4 3 0

TO INSTALL BLADE

See Figures 15, 16, 17 and 18. DANGER: A 8-1/4 in. (209.6 mm) blade is the maximum blade capacity of your saw. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guards, while thicker blades will prevent the blade bolt from securing the blade on the spindle. Either of these situations will result in a

Ryobi MS181 Depress the spindle lock button and rotate the

blade bolt until the spindle locks. See Figure 18. ■ Using the blade wrench provided, loosen and remove the blade bolt. Note: The blade bolt has left hand threads. Turn blade bolt clockwise to loosen. ■ Remove outer blade washer. Do not remove inner blade washer. ■ Wipe a drop of oil onto inner blade washer and outer blade washer where they contact the blade. WARNING: If inner bla

Note: Many of the illustrations in this manual show

only portions of your compound miter saw. This is intentional so that we can clearly show points being made in the illustrations. Never operate your saw without all guards securely in place and in good operating condition. SQUARING THE MITER TABLE TO THE FENCE See Figures 19 – 22. ■ Remove battery pack from saw. WARNING: Failure to remove battery pack

SQUARING THE SAW BLADE TO THE FENCE

See Figures 23 – 26. ■ Remove battery pack from saw. WARNING: Failure to remove battery pack from your saw could result in accidental starting causing possible serious personal injury. ■ Pull the saw arm all the way down and engage the lock pin to hold the saw arm in transport position. ■ Lift the miter

Using the 6 mm hex key provided, loosen the

socket head screws that secure the mounting bracket to the miter table. See Figure 26. SQUARING THE BLADE TO THE MITER TABLE See Figures 27 – 31. ■ Remove battery pack from saw. WARN

Ryobi Saw Owners Instructions: