Panasonic KX-TS85EXW Operating Instructions Manual

Model No. KX-TS85EXW Pulse-or-tone dialling capability Operating Instructions PLEASE READ BEFORE USE AND SAVE. ...

Thank you for purchasing your new Panasonic integrated telephone. Accessories (Included) Handset (p. 6) one Wall Mounting Adaptor (p. 29) one Handset Cord (p. 6) one Telephone Line Cord (p. 6) one For your future reference Serial No. Date of purchase (found on the bottom of the unit) Name and address of dealer ...

4 Display ................................................................................................. 5 Settings ................................................................................................ 6 Connecting the Handset/Telephone Line Cord ................................. 6 Connecting a Communication Device ......... ...

4 5 2 1 4 7 3 6 9 GHI JKL TUV MNO DEF R ABC PQRS WXYZ 8 0 Headset Jack (p. 27) Ringer Indicator (p. 13) Display (p. 5) One-Touch Auto Dial Buttons (p. 14) Lower Button (p. 15, 17) Recall Button (p. 21) R Program Button (p. 8, 14, 18) Mute Button (p. 21) Auto Button (p. 18) Redial/Pause Button (p. 12, 20) Speakerphone Button and Indicator (p. 12, 13, 28) , Volume Buttons (p. 12, 28) MIC (Micr ...

(Example: 15 minutes, 30 seconds) The unit is in the programming mode (p. 8, 14, 18). was pressed while dialling or storing phone numbers for the Speed Dialler (p. 18, 20). was pressed (p. 15, 17). The ringer is set to OFF (p. 9). was pressed during a conversation (p. 21). The dial lock mode is set. To cancel the mode, see page 23, 24. was pressed while storing phone numbers. was ...

Connecting the Handset/Telephone Line Cord After connecting the handset and telephone line cord, lift the handset to confirm the dial tone. LINE DATA Handset Cord Telephone Line Cord Handset To Single-Line Telephone Jack ...

(making calls, storing phone numbers in memory etc.), or the communication device may not operate properly. Connecting a Communication Device If you connect a communication device (computer, modem, fax, answering machine, etc.) to the telephone line, you can connect it through this unit using the DATA jack (—Data Port). After connecting the handset and telephone lin ...

You can select the dialling mode by programming. If you have touch tone service, set to TONE. If rotary or pulse service is used, set to PULSE. Your phone comes from the factory set to TONE. 1 Lift the handset. 2 Press . • “ ” is displayed. 3 Press (3). 4 To select PULSE, press (0). OR To select TONE, press (1). 5 Press . • A beep sounds on the handset. 6 Replace the handset. • To cancel during programming, ...

When set to OFF, the unit will not ring. Your phone comes from the factory set to ON. 1 Lift the handset. 2 Press . • “ ” is displayed. 3 Press (9). 4 To turn OFF, press (0). OR To turn ON, press (1). 5 Press . • A beep sounds on the handset. • When set to OFF, “ ” is displayed. 6 Replace the handset. In the stand-by mode, the display is blank. When the ringer is set to OFF, “ ” will be displayed wh ...

You can select the ringer volume by programming. Set to HIGH, MEDIUM or LOW. Your phone comes from the factory set to HIGH. 1 Lift the handset. 2 Press . • “ ” is displayed. 3 Press (6). 4 To select LOW, press (1). To select MEDIUM, press (2). OR To select HIGH, press (3). • Each time you press a button, the selected volume will ring. 5 Press . • A beep sounds on the handset. 6 Replace the handset. • To c ...

You can select one of 5 ringer tones. Your phone comes from the factory set to type 2. 1 Lift the handset. 2 Press . • “ ” is displayed. 3 Press (7). 4 Press a dialling button (0) to (4). • Each time you press a button, the selected tone will ring. 5 Press . • A beep sounds on the handset. 6 Replace the handset. • To cancel during programming, replace the handset. Start again from step 1. • I ...

2 Dial a phone number. • The dialled number is displayed. • After a few seconds, the display will show the length of the call. • If you misdial, hang up and start again from step 1. 3 When the other party answers, talk into the MIC (microphone). 4 To hang up, press . • The indicator light goes out. To adjust the handset volume (5 levels) or speaker volume (9 l ...

• For best speakerphone performance, talk alternately with the other party in a quiet room. • If the other party complains that your voice is hard to hear, press to decrease the speaker volume. • You can switch to the handset by lifting it up. To switch back to the speakerphone, press . and Indicator Ringer Indicator MIC • When the ringer volume is set to OFF (p. 9), the uni ...

(8 numbers in UPPER memory locations, 8 numbers in LOWER memory locations). Storing Phone Numbers in Memory It is recommended that you program an emergency number in the top left one-touch auto dial button. To prevent possible errors, do not press any one-touch auto dial buttons before storing . 1 Lift the handset. 2 Press . • “ ” is displayed. 3 Press one of ...

2 Press . • “ ” is displayed. 3 Press to select a lower memory location. • “ ” is displayed. 4 Press one of the one-touch auto dial buttons. • “ ” is displayed. 5 Enter a phone number up to 21 digits. • The entered number is displayed. 6 Press . • A beep sounds on the handset. 7 Replace the handset. • To store other numbers, repeat steps 1 through 7. To store in a LOWER memory location • I ...

1. Lift the handset. 2. Press . 3. If the phone number is in an UPPER memory location, press the one-touch auto dial button for the phone number to be erased. OR If the phone number is in a LOWER memory location, press , then press the one-touch auto dial button for the phone number to be erased. 4. Press and replace the handset. To store confidential numbers (Secret button feature) Confidential numbers stored ...

the stored numbers. Dialling a Stored Number From an UPPER memory location: 1 Lift the handset or press . 2 Press the desired one-touch auto dial button. • The stored number is displayed and dialled. OR From a LOWER memory location: 1 Lift the handset or press . 2 Press . 3 Press the desired one-touch auto dial button. • The stored ...

You can store up to 10 phone numbers in memory. The dialling buttons ((0) to (9)) function as memory stations. To prevent possible errors, do not press any memory stations before storing. 1 Lift the handset. 2 Press . • “ ” is displayed. 3 Press . • “ ” is displayed. 4 Press a memory station number ((0) to (9)). 5 Enter a phone number up to 21 digits. • The entered number is displayed. 6 Press ...

1. Lift the handset. 2. Press . 3. Press . 4. Press the memory station number ((0) to (9)) for the phone number to be erased. 5. Press and replace the handset. To store confidential numbers (Secret button feature) Confidential numbers stored in a memory station using this feature will not be displayed when dialling. The button functions as a secret button when storing. Press before and after the number(s) to b ...

1 Lift the handset or press . 2 Press . 3 Press the desired memory station number ((0) to (9)). • The stored number is displayed and dialled. How to Use the Pause Button (For Analogue PBX Line/Long Distance Service Users) We recommend you press if a pause is required for dialling with a PBX or to access a long distance service. Ex: Line access number (9) (PBX) (9) ➡ ➡ Phone number • Pressing once creates ...