Snapper 7600004 Operation & User’s Manual

ASSEMBLY INSTRUCTIONS OPERATOR'S MANUAL PARTS LIST Models covered: Includes Clamshell, Blower and Weight Kits 48” Kit P/N 7600003 52” Kit P/N 7600004 61” Kit P/N 7600005 Manual No. 7011299 (I.R. 03/11/05) Z-VAC Clamshell Grass Catcher Kit for NZM Mid Mount Riders ...

your new Z-Vac Grass Catcher Kit will provide years of dependable service. Please read and follow this instruction man- ual carefully in order to get the most out of your new equipment. As you carefully unpack your unit, you will find the following items: 1 Blower Kit (48” P/N 3071107, 52” P/N 307110 ...

TRAINING -- Read, understand, and follow all instructions in the man- ual and on the unit before starting. If the operator(s) or mechanic(s) can not read English it is the owner's responsi- bility to explain this material to them. -- Become familiar with the safe operation of the equipment, operator controls, and safety signs. -- All operators and mechanics should be trained. The owner is responsible fo ...

CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the unit and its activity. Never assume that children will remain where you last saw them. -- Keep children out of the mowing area and under the watchful care of another responsible adult. -- Do not allow children or others to ride on the machine, attachment, or towed equipment (even ...

STEP 1: Remove pin, rod and spring securing dis- charge deflector to mower deck, and remove deflector. Set rod and pin aside for future assem- bly step. Store deflector for future use. IMPOR- TANT: Never operate mower without discharge deflector or grass catcher securely in place. STEP 2: Remove two bolts securing right deck pul- ley guard to mower deck and remove guard. Set bolts aside for future assembly step. Store guard for future u ...

er mount, and secure with T-handle pin, making sure pin goes through both upper and lower holes in blower mount. Then align base of pin bracket parallel with rear of deck, and, using bracket as a template, drill two 7/16” holes through deck. Insert two 3/8-16 x 1” hex bolts up through deck and bracket, securing with hex flange lock nuts. Tighten securely. IMPORTANT: Use gloves when ...

and belt guard support clip on front part of blower mount. Secure with two 5/16 nylon wing nuts. Tighten nuts securely. !! Warning: Weight kit must be installed prior to installing clamshell kit. Failure to do so may result in longitudal tipping of unit. STEP 10: Lay weight mount channel, with installed weights, across front end of machine as shown. Secure to machine with two clamp plates, one under each cas ...

arm onto the hook on each side of the rear cover. Then secure the other end of the arm onto the inside of each side of the handle weldment with one 3/8-16 x 2” hex bolt and nyloc nut. Tighten snugly. NOTE: Make sure bend of arm is up. Push handle down to lock cover. 3 unit assembly STEP 13: Hook bottom of clamshell mount onto pins in bottom of bumper mount plate, then raise clamshell assembly up against bu ...

discharge hose, and install hose between blower and clamshell. NOTE: Install hose so that clamp with nut is on the clamshell side, and the clamp with the black quick-release knob is on the blower side. Tighten both clamps securely. unit assembly 3 9 CLAMP WITH NUT CLAMP WITH BLACK KNOB unit operation & maintenance 4 INTRODUCTION Follow operation and maintenance instructions in the Operator’s Manual ...

10 IF THE GRASS CATCHER BECOMES CLOGGED (Continued From Previous Page) 2. Empty catcher more often. 3. Clean screen on rear cover assembly. 4. Ground speed too fast – cut at slower speed. 5. Removing too much grass – raise cutting height, cut partial width, and cut lawn more frequently. 6. Grass is too wet from rain or dew – allow grass to dry. 7. Blades are dull or worn – inspect blades and replace as necessary. Use ...

11 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both. For one (1) year from purchase date for the original purchaser's c ...

Item Part No. Qty Description 1 3046782 1 WELDMENT, Blower Belt Guard 2 91121 1 NUT, 1/2-13 Hex Nyloc 3 90183 1 WASHER, 1/2" Flat SAE 4 3021097 1 PULLEY, A Groove Idler, Steel 5 44995 1 IDLER STUD (3/8-24 thread) 6 91804 2 FLAT WASHER, 9/16 Type Narrow 7 14409 2 FLANGE BEARING, 9/16" I.D. (powdered metal) 8 10776 1 RETAINING RING, 1/2" 9 3046824 1 BELT RETAINER, Idler 10 91527 1 SCREW, 5/16-18 x 1- ...

Item Part No. Qty Description 1 3036323 1 BELT, A Section, 91.125" effective length (used on 48” & 52” Models) 1 3022844 1 BELT, A Section, 92.0" effective length (used on 61” Models) 2 3037161 1 WELDMENT, Belt Cover, Deck (used on 48” & 52” Models) 2 33867 1 WELDMENT, Belt Cover, Deck (used on 61” Models) 3 ----- -- NOT USED 4 91537 2 WING LOCKNUT 5/16-18 5 3037162 1 BELT GUARD, 48" D ...

Item Part No. Qty Description 1 72979 1 COVER, Rear, Clamshell Bagger -- 73509 1 SCREEN, Clamshell (Not Shown) -- 73525 8 RIVET, 5/32 (Not Shown) 2 58600 1 WELDMENT, Rear Cover Brace 3 73179 1 HINGE, Rear Cover 4 91265 5 SCREW, #10-24 x 1-1/2” Hex Washer Machine 5 36422 18 WASHER, .190 ID x .75 OD Flat 6 91079 18 NUT, 10-24 Hex Flange Lock 7 73145 13 BOLT, #10-24 x 1-1/2” Oval Head 8 91304 2 SCREW, 3/8-16 x 1" Hex ...

Item Part No. Qty Description 1 50551 2 STANDOFF, Bumper Mount (weldment) 2 1723436 1 WELDMENT, Bumper Mount Plate 3 91318 4 SCREW, 5/16-18 x 3/4" Hex Head Cap, GR5 4 91601 4 NUT, 5/16-18 Hex Flange Lock, GR5 5 1717085 1 ROD, Hitch 6 15067 1 HAIR PIN, 3/32 x 1-1/2" Cotter unit breakdown & parts list 6 19 ...