Sony CDX-M800 Service Manual

Model Name Using Similar Mechanism CDX-L410X/L490X CD Drive Mechanism Type MG-393XC-121//K Optical Pick-up Name KSS-721A SERVICE MANUAL US Model Canadian Model AEP Model UK Model E Model CDX-M800 • The tuner and CD sections have no adjustments. AUDIO POWER SPECIFICATIONS (US MODEL) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 23.2 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5% total harmonic distortion. CD player section Signal-to-noise ratio 90 dB Frequency response 10 – 20,000 Hz Wow and flutter Below measurable limit Tuner section FM Tuning range 87.5 – 107.9 MHz (US, Canadian model) 87.5 – 108.0 MHz (AEP, UK, E model) Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Usable sensitivity 9 dBf Selectivity 75 dB at 400 kHz Signal-to-noise ratio 67 dB (stereo), 69 dB (mono) Harmonic distortion at 1 kHz 0.5% (stereo), 0.3% (mono) Separation 35 dB at 1 kHz Frequency response 30 – 15,000 Hz AM (US, Canadian model) Tuning range 530 – 1,710 kHz Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity 30 µV SPECIFICATIONS MW/LW (AEP, UK, E model) Tuning range MW: 531 – 1,602 kHz LW: 153 – 279 kHz Aerial terminal External aerial connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity MW: 30 µV LW: 40 µV Power amplifier section Outputs Speaker outputs (sure seal connectors) Speaker impedance 4 – 8 ohms Maximum power output 52 W × 4 (at 4 ohms) General Outputs Audio outputs (front/rear) Subwoofer output (mono) Power antenna relay control terminal (US, Canadian model) Power aerial relay control terminal (AEP, UK, E model) Power amplifier control terminal FM/AM COMPACT DISC PLAYER US, Canadian Model FM/MW/LW COMPACT DISC PLAYER AEP, UK, E Model – Continued on next page – Sony Corporation e Vehicle Company Published by Sony Engineering Corporation 9-874-299-01 2003A0400-1 © 2003. 01

semi-fixed resistor SERVICE NOTES Inputs Telephone ATT control terminal Illumination control terminal (US, Canadian model) BUS control input terminal BUS audio input or AUX IN terminal Antenna input terminal (US, Canadian model) Aerial input terminal (AEP, UK, E model) Tone controls US, Canadian model: Bass ±10 dB at 62 Hz Treble ±10 dB at 16 kHz AEP, UK, E model: Bass ±8 dB at 100 Hz Treble ±8 dB at 10 kHz Loudness +8 dB at 100 Hz +2 dB at 10 kHz Power requirements 12 V DC car battery (negative ground) Dimensions Approx. 178 × 50 × 186 mm (7 1/8 × 2 × 7 3/8 in.) (w/h/d) Mounting dimensions Approx. 182 × 53 × 163 mm (7 1/4 × 2 1/8 × 6 1/2 in.) (w/h/d) Mass Approx. 1.5 kg (2 lb. 10 oz.) Supplied accessories Parts for installation and connections (1 set) Card remote commander RM-X110 (US, Canadian model) RM-X111 (AEP, UK, E model) Note This unit cannot be connected to a digital preamplifier or an equalizer. Design and specifications are subject to change without notice. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick- up block. Therefore, when checking the laser diode emission, ob- serve from more than 30 cm away from the objective lens. Notes on Chip Component Replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be dam- aged by heat. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. If the optical pick-up block is defective, please replace the whole optical pick-up block. Never turn the semi-fixed resistor located at the side of optical pick-up block. US, Canadian model: CDX-M800 SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

• You can play CD-Rs (recordable CDs)/CD-RWs (rewritable CDs) designed for audio use on this unit. Look for these marks to distinguish CD-Rs/CD-RWs for audio use. These marks denote that a disc is not for audio use. • Some CD-Rs/CD-RWs (depending on the equipment used for its recording or the condition of the disc) may not play on this unit. • You cannot play a CD-R/a CD-RW that is not finalized∗. ∗A process necessary for a recorded CD-R/CD-RW disc to be played on the audio CD player. stand NOTE FOR THE OPENING OF THE FRONT PANEL In this set, the front panel is lowered to below the bottom face when it is opened. When servicing the set, place it on a stand having a height of about 2 cm. AEP, UK, E model: This label is located on the bottom of the chassis. This label is located on the drive unit’s internal chassis. When replacing the chassis (T) of mechanism deck which have the “CAUTION LABEL” attached, please be sure to put a new CAUTION LABEL (3-223-913-11) to the chassis (T). CDX-M800 TEST DISCS This set can playback CD-R and CD-ROM discs. The following test discs should be used to check the capability: CD-R test disc TCD-R082LMT (Part No. J-2502-063-1) CD-RW test disc TCD-W082L (Part No. J-2502-063-2)

When repairing or servicing this set, connect the jig (extension cable) as shown below. • Connect the MAIN board (CNP301) and the SERVO board (CN1) with the extension cable (Part No. J-2502-062-1). CDX-M800 MAIN BOARD CNP301 SERVO BOARD CN1

1. GENERAL Location of Controls................................................................ 6 Connection example (US, Canadian Model) ........................... 6 Connections (US, Canadian Model)........................................ 7 2. DISASSEMBLY 2-1. Front Panel Assy ................................................................. 8 2-2. CD Mechanism Block, Front Panel Assy............................ 9 2-3. Sub Panel (CD) Sub Assy ................................................... 9 2-4. Motor Block Assy, Cam (R) Assy ..................................... 10 2-5. Main Board ....................................................................... 10 2-6. Heat Sink ........................................................................... 11 2-7. Chassis (T) Sub Assy ........................................................ 11 2-8. Lever Section, In Self SW Board ...................................... 12 2-9. Servo Board ....................................................................... 12 2-10. Shaft Roller Assy, Load SW Board ................................... 13 2-11. Floating Block Assy .......................................................... 13 2-12. Optical Pick-up Block ....................................................... 14 3. PHASE ALIGNMENT 3-1. Arm (A-L) Assy, Arm (B-L) Assy ..................................... 15 3-2. Cam (L) ............................................................................. 15 3-3. Motor Block ...................................................................... 16 3-4. Alignment between Arm (A-L) Assy and Arm (B-L) Assy .......................................................... 16 3-5. Arm (A-R) Assy, Arm (B-R) Assy .................................... 17 3-6. Cam (R) ............................................................................. 17 CDX-M800 4. DIAGRAMS 4-1. IC Pin Descriptions ........................................................... 18 4-2. Block Diagram –CD Section–........................................... 21 4-3. Block Diagram –Tuner Section– ....................................... 22 4-4. Block Diagram –Display Section– .................................... 23 4-5. Circuit Boards Location .................................................... 24 4-6. Schematic Diagram –CD Mechanism Section– ................ 25 4-7. Printed Wiring Boards –CD Mechanism Section–............ 26 4-8. Printed Wiring Boards –Main Section– ............................ 28 4-9. Schematic Diagram –Main Section (1/2)– ........................ 30 4-10. Schematic Diagram –Main Section (2/2)– ........................ 31 4-11. Printed Wiring Board –Sub Section– ................................ 32 4-12. Schematic Diagram –Sub Section– ................................... 33 4-13. Printed Wiring Board –Display Section– .......................... 34 4-14. Schematic Diagram –Display Section–............................. 35 4-15. IC Block Diagrams............................................................ 36 5. EXPLODED VIEWS 5-1. Chassis Section ................................................................. 39 5-2. Cam Section ...................................................................... 40 5-3. Main Board Section .......................................................... 41 5-4. Front Panel Section ........................................................... 42 5-5. CD Mechanism Section (1) ............................................... 43 5-6. CD Mechanism Section (2) ............................................... 44 5-7. CD Mechanism Section (3) ............................................... 45 6. ELECTRICAL PARTS LIST......................................... 46

Refer to the pages listed for details. a SCRL (scroll) button 10 b DSPL (display mode change) button 10, 12 c Number buttons (1) REP 11 (2) SHUF 11 To store stations/receive stored stations. d EQ7 button 18 e MENU button To display the menus. f SOURCE (Power on/Radio/CD/MD*1/ AUX*2) button To select the source. g SEEK () button k MENU button m LIST/CAT*2 button o CLOSE (front panel close) button 9 p SOURCE button q MODE button r VOL (–/+) button s DSO button t EQ7 button u SOUND button v DISC (+/–) buttons w ENTER button x Z (eject) button 9 Main display side Operation side CDX-M800 continue to next page t Connection example (2) Notes (2-A) • Be sure to connect the ground cord before connecting the amplifier. • If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated. Tip (2-B- ) For connecting two or more CD/MD changers, the source selector XA-C30 (optional) is necessary. Exemple de raccordement (2) Remarques (2-A) • Raccordez d’abord le fil de masse avant de raccorder l’amplificateur. • Si vous raccordez un amplificateur de puissance en option et que vous n’utilisez pas l’amplificateur intégré, le bip sonore est désactivé. Conseil (2-B- ) Dans le cas du raccordement de deux changeurs de CD/MD ou plus, le sélecteur de source XA-C30 (en option) est requis. Ejemplo de conexiones (2) Notas (2-A) • Asegúrese de conectar primero el cable de puesta a masa antes de realizar la conexión al amplificador. • Si conecta un amplificador de potencia opcional y no utiliza el incorporado, los pitidos se desactivarán. Consejo (2-B- ) Cuando desee conectar dos o más cambiadores de CD/MD, necesitará un selector de fuente XA-C30 (opcional). BUS CONTROL IN BUS AUDIO IN Source selector* Sélecteur de source* Selector de fuente* XA-C30 * not supplied non fourni no suministrado 2 A B AUDIO OUT FRONT AUDIO OUT REAR BUS AUDIO IN BUS CONTROL IN SUB OUT (MONO)

L R BUS AUDIO IN AUDIO OUT REAR FRONT AUX IN Schéma de raccordement (3) 1 À un point métallique de la voiture Branchez d‘abord le fil de masse noir et, ensuite, les fils d‘entrée d‘alimentation jaune et rouge. 2 Vers le fil de commande de l‘antenne électrique ou le fil d‘alimentation de l‘amplificateur d‘antenne Remarques • Il n'est pas nécessaire de raccorder ce fil s'il n'y a pas d'antenne électrique ni d'amplificateur d'antenne, ou avec une antenne télescopique manuelle. • Si votre voiture est équipée d'une antenne FM/AM intégrée dans la vitre arrière/latérale, voir “Remarques sur les fils de commande et d'alimentation”. 3 Au niveau du AMP REMOTE IN de l’amplificateur de puissance en option Ce raccordement s’applique uniquement aux amplificateurs. Le branchement de tout autre système risque d’endommager l’appareil. 4 Vers le cordon de liaison d’un téléphone de voiture 5 Vers le connecteur du signal d’éclairage de la voiture Raccordez d‘abord le fil de masse noir à un point métallique de la voiture. 6 À la borne +12 V qui est alimentée quand la clé de contact est sur la position accessoires Remarques • S'il n'y a pas de position accessoires, raccordez la borne d'alimentation (batterie) +12 V qui est alimentée en permanence. Raccordez d‘abord le fil de masse noir à un point métallique de la voiture. • Si votre voiture est équipée d'une antenne FM/AM intégrée dans la vitre arrière/latérale, voir “Remarques sur les fils de commande et d'alimentation”. 7 À la borne +12 V qui est alimentée en permanence Raccordez d‘abord le fil de masse noir à un point métallique de la voiture. Remarques sur les fils de commande et d'alimentation • Le fil de commande de l’antenne électrique (bleu) fournit une alimentation de + 12 V CC lorsque vous mettez la radio sous tension. • Lorsque votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, raccordez la sortie de commande de l’antenne (bleu) ou l’entrée d’alimentation des accessoires (rouge) à la borne de l’amplificateur d’antenne existant. Pour plus de détails, consultez votre détaillant. • Une antenne électrique sans boitier de relais ne peut pas être utilisée avec cet appareil. Raccordement pour la conservation de la mémoire Lorsque le fil d’entrée d’alimentation jaune est raccordé, le circuit de la mémoire est alimenté en permanence même si la clé de contact est sur la position d’arrêt. Remarques sur le raccordement des haut-parleurs • Avant de raccorder les haut-parleurs, mettez l’appareil hors tension. • Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms avec une capacité électrique adéquate pour éviter de les endommager. • Ne raccordez pas les bornes du système de haut-parleur au châssis de la voiture et ne raccordez pas les bornes du haut-parleur droit à celles du haut-parleur gauche. • Ne raccordez pas le câble de masse de cet appareil à la borne négative (–) de l’enceinte. • N’essayez pas de raccorder les haut-parleurs en parallèle. • Raccordez uniquement des haut-parleurs passifs. Le raccordement de haut-parleurs actifs (avec amplificateurs intégrés) aux bornes des haut-parleurs peut endommager l’appareil. • Pour éviter tout dysfonctionnement, n’utilisez pas les fils des haut- parleurs intégrés installés dans votre voiture si l’appareil partage un fil négatif commun (–) pour les haut-parleurs droit et gauche. • Ne raccordez pas entre eux les cordons des haut-parleurs de l’appareil. Remarque sur le raccordement Si les enceintes et l’amplificateur ne sont pas raccordés correctement, le message “Failure” s’affiche. Dans ce cas, assurez- vous que les enceintes et l’amplificateur sont bien raccordés. 3 BUS AUDIO IN /AUX IN*5 Source selector (not supplied) Sélecteur de source (non fourni) Selector de fuente (no suministrado) XA-C30 2 6 7 4 AMP REM ANT REM 4 Max. supply current 0.3 A Courant max. fourni 0,3 A Corriente máx. de alimentación de 0,3 A Fuse (10 A) Fusible (10 A) Fusible (10 A) Red Rouge Rojo Yellow Jaune Amarillo Black Noir Negro Blue Bleu Azul Blue/white striped Rayé bleu/blanc Con rayas azules y blancas White Blanc Blanco Green Vert Verde Purple Mauve Morado White/black striped Rayé blanc/noir Con raya blanca/negra Gray/black striped Rayé gris/noir Con raya gris/negra Green/black striped Rayé vert/noir Con raya verde/negra Purple/black striped Rayé mauve/noir Con raya violeta/negra BUS CONTROL IN AUDIO OUT FRONT Gray Gris Gris AUDIO OUT REAR Supplied with the CD/MD changer Fourni avec le changeur de CD/MD Suministrado con el cambiador de CD/MD 3 Left Gauche Izquierdo Right Droit Derecho Left Gauche Izquierdo Right Droit Derecho Light blue Bleu ciel Azul celeste Max. supply current 0.1 A Courant d’alimentation max. 0,1 A Corriente máx. de alimentación de 0,1 A ATT 1 SUB OUT (MONO) *1 Diagrama de conexión (3) 1 A una superficie metálica del automóvil Conecte primero el cable de puesta a masa negro, y después los cables amarillo y rojo de entrada de alimentación. 2 Al cable de control de la antena motorizada o al cable de fuente de alimentación del amplificador de antena Notas • Si no se dispone de antena motorizada ni de amplificador de antena, o se utiliza una antena telescópica accionada manualmente, no será necesario conectar este cable. • Si el automóvil incorpora una antena de FM/AM en el cristal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”. 3 Para conectar a AMP REMOTE IN del amplificador de potencia opcional Esta conexión es sólo para amplificadores. La conexión de cualquier otro sistema puede dañar la unidad. 4 Al cable de interfaz de un teléfono para automóvil 5 A una señal de iluminación del automóvil Asegúrese de conectar primero el cable de tierra negro a una superficie metálica del automóvil. 6 Al terminal de alimentación de +12 V que recibe energía en la posición de accesorio del interruptor de la llave de encendido Notas • Si no hay posición de accesorio, conéctelo al terminal de alimentación (batería) de +12 V que recibe energía sin interrupción. Asegúrese de conectar primero el cable de tierra negro a una superficie metálica del automóvil. • Si el automóvil incorpora una antena de FM/AM en el cristal trasero/lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”. 7 Al terminal de alimentación de +12 V que recibe energía sin interrupción Asegúrese de conectar primero el cable de tierra negro a una superficie metálica del automóvil. Notas sobre los cables de control y de fuente de alimentación • El conductor de control de la antena motorizada (azul) suministrará + cc 12 V cuando conecte la alimentación del sintonizador. • Si el automóvil dispone de una antena de FM/AM incorporada en el cristal trasero o lateral, conecte el cable de control de antena motorizada (azul) o el cable de entrada de alimentación auxiliar (rojo) al terminal de alimentación del amplificador de antena existente. Para obtener información detallada, consulte a su proveedor. • Con esta unidad no es posible utilizar una antena motorizada sin caja de relé. Conexión para protección de la memoria Si conecta el conductor de entrada amarillo, el circuito de la memoria recibirá siempre alimentación, aunque ponga la llave de encendido en la posición OFF. Notas sobre la conexión de los altavoces • Antes de conectar los altavoces, desconecte la alimentación de la unidad. • Utilice altavoces con una impedancia de 4 a 8 Ω con la capacidad de potencia adecuada para evitar que se dañen. • No conecte los terminales de altavoz al chasis del automóvil, ni conecte los terminales del altavoz derecho con los del izquierdo. • No conecte el cable de puesta a masa de esta unidad al terminal negativo (–) del altavoz. • No intente conectar los altavoces en paralelo. • Conecte solamente altavoces pasivos. Si conecta altavoces activos (con amplificadores incorporados) a los terminales de altavoz, puede dañar la unidad. • Para evitar fallos de funcionamiento, no utilice los cables de altavoz incorporados instalados en el automóvil si su unidad comparte un cable negativo común (–) para los altavoces derecho e izquierdo. • No conecte los cables de altavoz de la unidad entre sí. Nota sobre la conexión Si el altavoz y el amplificador no están conectados correctamente, aparecerá “Failure” en la pantalla. Si es así, compruebe la conexión de ambos dispositivos. Orange/white striped Rayé orange/blanc Con rayas naranjas y blancas 5 ILLUMINATION *4 *1 *1 RCA pin cord (not supplied) Cordon à broche RCA (non fourni) Cable con terminales RCA (no suministrado) *2 Supplied with XA-C30 Fourni avec le XA-C30 Suministrado con el XA-C30 *3 Auxiliary optional equipment such as portable DVD player (not supplied) Appareil auxiliaire en option, par exemple un lecteur de DVD (non fourni) Equipo opcional auxiliar como un reproductor de DVD portátil (no suministrado) *4 Supplied with the auxiliary equipment Fourni avec l’appareil auxiliaire Suministrado con el equipo auxiliar *5 Be sure to match the color-coded code for audio to the appropriate jacks from the unit. If you connect an optional CD/ MD unit, you cannot use AUX IN terminal. Veillez à faire correspondre le code couleur audio aux fiches de l’appareil. Si vous raccordez un appareil CD ou MD en option, vous ne pouvez pas utiliser la borne AUX IN. Asegúrese de hacer coincidir el código codificado con colores para audio con las tomas apropiadas de la unidad. Si conecta una unidad de CD/MD opcional, no podrá utilizar el terminal AUX IN. *2 from car antenna à partir de l’antenne de la voiture desde la antena del automóvil *3 Connection diagram (3) 1 To a metal surface of the car First connect the black ground lead, then connect the yellow and red power input leads. 2 To the power antenna control lead or power supply lead of antenna booster amplifier Notes • It is not necessary to connect this lead if there is no power antenna or antenna booster, or with a manually-operated telescopic antenna. • When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.” 3 To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. 4 To the interface cable of a car telephone 5 To a car’s illumination signal Be sure to connect the black ground lead to a metal surface of the car. 6 To the +12 V power terminal which is energized in the accessory position of the ignition key switch Notes • If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to connect the black ground lead to a metal surface of the car. • When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.” 7 To the +12 V power terminal which is energized at all times Be sure to connect the black ground lead to a metal surface of the car. Notes on the control and power supply leads • The power antenna control lead (blue) supplies +12 V DC when you turn on the tuner. • When your car has built-in FM/AM antenna in the rear/ side glass, connect the power antenna control lead (blue) or the accessory power input lead (red) to the power terminal of the existing antenna booster. For details, consult your dealer. • A power antenna without relay box cannot be used with this unit. Memory hold connection When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition key is turned off. Notes on speaker connection • Before connecting the speakers, turn the unit off. • Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. • Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. • Do not connect the ground lead of this unit to the negative (–) terminal of the speaker. • Do not attempt to connect the speakers in parallel. • Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. • To avoid a malfunction, do not use the built-in speaker wires installed in your car if the unit shares a common negative (–) lead for the right and left speakers. • Do not connect the unit’s speaker cords to each other. Note on connection If speaker and amplifier are not connected correctly, “Failure” appears in the display. In this case, make sure the speaker and amplifier are connected correctly.

Note : Follow the disassembly procedure in the numerical order given. 2-1. FRONT PANEL ASSY 2-1. FRONT PANEL ASSY (Page 8) 2-2. CD MECHANISM BLOCK, FRONT PANEL ASSY (Page 9) 2-7. CHASSIS (T) SUB ASSY (Page 11) 2-8. LEVER SECTION, IN SELF SW BOARD (Page 12) 2-10. SHAFT ROLLER ASSY, LOAD SW BOARD (Page 13) 2-11. FLOATING BLOCK ASSY (Page 13) 2-12. OPTICAL PICK-UP BLOCK (Page 14) SET 2-9. SERVO BOARD (Page 12) 2-5. MAIN BOARD (Page 10) 2-6. HEAT SINK (Page 11) 2-3. SUB PANEL (CD) SUB ASSY (Page 9) 2-4. MOTOR BLOCK ASSY, CAM (R) ASSY (Page 10) 1 screw (panel) flexible board 3 4 front panel assy (Take care not to pull the flexible board excessively) 2 screw (panel)

2-3. SUB PANEL (CD) SUB ASSY 2 PTT 2.6x4 4 CNP301 1 PTT 2.6x6 3 PTT 2.6x4 5 CD mechanism block 7 bracket (CD) 6 PTT 2.6x6 8 tension spring (flexible) flexible board 9 slider (flexible) slider (flexible) 0 cover (flexible) qa CNP909 Note: When installing the flexible board, make the board slack as illustrated. qs front panel assy 4 sub panel (CD) sub assy 2 claws 1 CNP805 3 claws

Note : Install the motor block assy and cam (R) assy in this roder. For phase alignment between cams (L) and (R), see page 15 and 17. 2-5. MAIN BOARD 1 PTT 2.6x6 4 PTT 2.6x6 5 motor block assy 2 cam (R) assy 3 CNP902 A Note: Install the cam (R) assy with the cam fully rotated in the direction of the arrow A. 4 PTT 2.6x6 ground point 3 PTT 2.6x6 ground point 1 PTT 2.6x6 5 MAIN board 2 PTT 2.6x6

2-7. CHASSIS (T) SUB ASSY 5 heat sink 2 PTT 2.6x6 4 PTT 2.6x6 3 PTT 2.6x12 1 PTT 2.6x6 4 chassis (T) sub assy 3 P 2x3 2 P 2x3 1 Unsolder the lead wires. black red white

2-9. SERVO BOARD 4 claws 2 IN SELF SW board 7 lever (L) 3 tension spring (LR) 6 lever (R) 5 guide (disc) 1 special screw 6 special screws 1 CN3 2 Removal the solders. 4 P 2x3 5 loading motor assy 8 SERVO board 7 special screw 9 FLEXIBLE board optical pick-up block 3 Unsolder the lead wires. black yellow

2-11. FLOATING BLOCK ASSY Fig. 1 1 tension spring (RA) 2 arm (roller) 3 retaining ring (RA) 4 shaft retainer (roller) 5 shaft roller assy 6 special screw 7 LOAD SW board retaining ring (RA) arm arm washer washer shaft retainer (roller) shaft retainer (roller) 1 tension spring (KF1) 7 compression spring (FL) 6 floating block assy 8 compression spring (FL) 4 Fit lever (D) in the direction of the arrow. 2 damper (T) 3 damper (T) 5 Turn loading ring in the direction of the arrow.

1 P 2x3 4 screw 5 plate spring (feed) 6 shaft (feed) assy 2 sled motor assy 3 optical pick-up block

arm (B-L) assy C A B 3 type-E stop ring 1.5 hole (large) line SECTION 3 PHASE ALIGNMENT 3-1. ARM (A-L) ASSY, ARM (B-L) ASSY 3-2. CAM (L) 1 Move the arm (B-L) assy in the direction of the arrow A and the arm (A-L) assy in the direction of the arrow B fully (full open state). 2 Align the hole (large) on the cam (L) with part C and install the cam. 4 Turn the cam (L) clockwise and counterclockwise to verify that both the arms are operated. 4 type-E stop ring 1.5 2 type-E stop ring 1.5 1 arm (B-L) assy 3 arm (A-L) assy bracket (L) assy

3-4. ALIGNMENT BETWEEN ARM (A-L) ASSY AND ARM (B-L) ASSY 1 Turn the cam (L) and position the cam so that part A does not touch the SW board SW900. 1 Input 9V DC to the motor terminal until the cam (L) stops rotating. Take care to avoid overload of the motor. 2 Verify that the arm (A-L) assy and arm (B-L) assy are positioned as shown below (full open). 3 PTT 2.6x6 4 PTT 2.6x6 5 PTT 2.6x6 2 motor block SWITCH board SW900 cam (L) A motor GND arm (B-L) assy arm (A-L) assy DC 9V +B

3-5. ARM (A-R) ASSY, ARM (B-R) ASSY 1 Move the arm (B-R) assy in the direction of the arrow A and the arm (A-R) assy in the direction of the arrow B fully (full open state). 2 Align the hole (large) on the cam (R) with part C and install the cam. 4 Turn the cam (R) clockwise and counterclockwise to verify that both the arms are operated. bracket (R) assy 3 arm (A-R) assy 4 type-E stop ring 1.5 2 type-E stop ring 1.5 1 arm (B-R) assy 3 type-E stop ring 1.5 5 oil damper 6 screw (P 2x4) cam (R) B A C arm (B-R) assy hole (large) line arm (A-R) assy

• IC303 M30626FHPGP-052 (US, Canadian model) (SYSTEM CONTROL) (MAIN Board (2/2)) • IC303 M30626FHPGP-053 (AEP, UK, E model) (SYSTEM CONTROL) (MAIN Board (2/2)) Pin No. Pin Name I/O Pin Description 1 SIRCS I Remote control data input 2 FP CTRL O Front panel open/close speed control signal 3 CD SO/TSO O CD servo serial data output 4 CD SI/TSI I CD servo serial data input 5 CD CKO/TCKO O CD servo serial clock output 6 BYTE I L fixed terminal 7 CNVSS I Flash write-in signal input 8 XIN I Sub clock signal input (32kHz) 9 XOUT O Sub clock signal output (32kHz) 10 RESET I CPU reset signal input 11 OSC OUT O Main clock signal output (6MHz) 12 VSS — Ground 13 OSC IN I Main clock signal input (6MHz) 14 VCC1 — Power supply pin (+5V) 15 NMI I Non maskable interrupt signal input 16 CD PACK I CD text pack synchronized signal input 17 DAVN I RDS data acquisition detect signal 18 BU IN I Back-up power detect signal 19 NS MASK O Not used. (Open) 20 BEEP O Beep signal output 21 FLW IN I OSC frequency shift signal for DC/DC conv. 22 NCO O Not used. (Open) 23 SA CLK O Spectrum analyzer clock signal output 24 TEL ATT I telephone mute detect signal input 25 ATT O Mute signal output 26 VOL ATT O Electronic volume mute signal output 27 I2C CKO O Tuner/E-volume BUS clock output 28 I2C SIO O Tuner/E-volume BUS data output 29 UNI SO O SONY BUS data output 30 UNI SI I SONY BUS data input 31 UNI CKO O SONY BUS clock output 32 TUNER ATT O Tuner attenuate signal output 33 EESIO I/O EEPROM data input/output 34 EECKO O EEPROM clock output 35 NCO O Not used. (Open) 36 ADSO1 O Not used. (Open) 37 ADSO2 O Not used. (Open) 38 NCO O Not used. (Open) 39 HOLD I Flash write-in signal input 40 AMP DIAG I Amplifier diagnosis signal input 41 AMP STB O Amplifier strobe signal output 42 AMP ON O Not used. (Open) 43 TUNER ON O Not used. (Open) 44 WRI/WR I Flash write-in signal input 45 CD LIMIT I CD limit detect signal input 46 CD D SW I CD disc SW detect signal input 47 CD PH1 I CD PH1 detect signal input 48 CD INSW/PH2 I CD IN SW/PH2 detect signal input 49 PH3 I CD PH3 detect signal input 50 DST SEL1 I Destination select signal input SECTION 4 DIAGRAMS

52 CD LM LO O CD loading motor control signal output 53 CD LM EJ O CD eject motor control signal output 54 CD RST O CD servo reset signal output 55 CD AO O CD servo command/parameter discri. output 56 CD STB O CD servo data strobe signal output 57 CD TSTB O CD servo text strobe signal output 58 CD RFOK I CD servo RFOK signal input 59 CD XTALEN O CD servo crystal OSC control signal output 60 VCC2 — Power supply pin (+5V) 61 RESET OUT O Display CPU reset signal output 62 VSS — Ground 63 TEST IN I Test mode setting detect signal input 64 BUS ON O BUS ON control signal output 65 SYS RST O System reset signal output 66 BUS/AUX O BUS/AUX select control signal output 67 LINK OFF O Link OFF control signal output 68 ACC IN I Accessory key ON detect signal input 69 ILL IN I Ilumination line detect signal input 70 RC IN1 I Rotary commander signal input 1 71 NCO O Not used. (Open) 72 CD SELF SW I CD self SW detect signal input 73 TU ATT IN I Tuner mute control signal input 74 CLOSE SW I Front panel close detect signal input 75 OPEN SW I Front panel open detect signal input 76 I-DET I Front panel current detect signal input 77 MOT– O Front panel open/close control signal output 78 MOT+ O Front panel open/close control signal output 79 ROMC EN I ROM correction enable signal input 80 QUALITY I Tuner noise detect signal input 81 MPTH I Tuner multi-path signal input 82 VSM I S-meter signal input 83 SA IN I SA data input 84 KEY IN1 I Key signal input 1 85 KEY IN0 I Key signal input 0 86 RC IN0 I Rotary commander signal input 0 87 KEY ACK2 I Key acknowledge detect signal input 2 88 KEY ACK0 I Key acknowledge detect signal input 0 89 KEY ACK1 I Key acknowledge detect signal input 1 90 OPEN KEY I Open key detect signal input 91 RAM BU I RAM reset detect signal input 92 FLD ON O FL driver power supply ON/OFF signal output 93 FL ON O FL power supply ON/OFF signal 94 AVSS — Ground 95 DISP CE O Display CPU chip enable output 96 VREF — A/D converter reference voltage (+5V) 97 AVCC — Power supply pin (+5V) 98 DISP SI/RX I Display CPU BUS data input 99 DISP SO/TX O Display CPU BUS data output 100 DISP CKO O Display CPU BUS clock output

Pin No. Pin Name I/O Pin Description 1 SYS RST I Main chip enable input 2 NC I Not used. (Open) 3 FL DATA3 O FL serial data output 4 NC O Not used. (Open) 5 FL CLK IN I FL serial clock input 6 BYTE I L fixed terminal 7 CNVSS I Flash write-in signal input 8 NC O Not used. (Open) 9 NC O Not used. (Open) 10 RESET I CPU reset signal input 11 XOUT O Main clock signal output (30MHz) 12 VSS — Ground 13 XIN I Main clock signal input (30MHz) 14 VCC — Power supply pin (+5V) 15 NMI I Non maskable interrupt signal input 16 NC O Not used. (Open) 17 NC O Connecting to pin 20. 18 NC O Not used. (Open) 19 NC O Not used. (Open) 20 NC O Connecting to pin 17. 21 LAT O FL data LAT output 22 BK O FL BK output 23 GCP2 O FL GCP2 outpit 24 NC O Not used. (Open) 25 GCP1 O FL GCP1 output 26 NC O Not used. (Open) 27 GCP4 O FL GCP4 output 28 GCP3 O FL GCP3 output 29 SYS SO O Main BUS data output 30 SYS SI I CPU BUS data input 31 SYS CLK O Main BUS clock input 32 NC O Not used. (Open) 33 FL DAT1 O FL serial data output 34 NC O Not used. (Open) 35 FL CLK O FL serial clock output 36 LCD CE O LCD driver chip enble output 37 LCD INH O LCD driver inhibit output 38 NC O Not used. (Open) 39 HOLD I Flash write-in signal input 40 – 43 NC O Not used. (Open) 44 WRI/WR I Flash write-in signal input 45 – 59 NC O Not used. (Open) 60 VCC O Power supply pin (+5V) 61 NC O Not used. (Open) 62 VSS O Ground 63 – 93 NC O Not used. (Open) 94 AVSS — Ground 95 NC O Not used. (Open) 96 VREF — Power supply pin (+5V) 97 AVCC — Power supply pin (+5V) 98 RXD1 — Not used. (Open) 99 FL DATA2 O FL serial data output 100 FL CLK IN I FL serial clock input

CD RFOK CD D SW CD IN SW CD SELF SW CD LIMIT CD LM LO CD LM EJ R-CH TUNER SECTION A 23 24 M M M LOUT ROUT PACK TSTB TSI TSCK SI RFOK SO SCK STB AO XTALEN RST A C B D E F PD LD B D A C E F PD A+5V LD APC FCS- FCS+ TRK+ TRK- SL- SL+ SP+ SP- LD- LD+ FOCUS COIL TRACKING COIL FD TD SD MD LOAD EJECT SYSTEM CONTROL IC303 (1/3) RF AMP,DIGITAL SERVO DIGITAL SIGNAL PROCESSOR FOCUS/TRACKING COIL DRIVE, SLED/SPINDLE/LOADING MOTOR DRIVE FD TD SD MD • Signal path :CD • R-ch is omitted due to same as L-ch. IC1 IC2 4-2. BLOCK DIAGRAM — CD SECTION — (Page 22)

27 I2C CKO 17 DAVN 73 TU ATT IN 82 VSM MUTE SCL SDA AM AML 32 AC OUT L 31 AC IN L 8 MUTE CONDITION 6 S-METER 17 SDA 33 EESIO 16 SCL 34 EECKO RDS DECODER IC502 FM DET OSCD OSCI 4 5 X501 4.3MHz 9 SDA SCL 80 QUALITY 10 DAVN 8 4 PDL 42 MDL ELECTRONIC VOLUME IC401 25 LF 24 OUT LR 17 OUT SW 14 SA CLK 16 SA OUT 66 BUS/AUX 43 SA IN 25 ATT 20 BEEP 41 AMP STB AMPDIAG 9 XOUT 40 8 XIN 11 OSCOUT 13 OSCIN A Q408 23 SA CLK Q171 Q181 Q470 12 5 3 11 2 4 16 22 25 34 30 37 33 31 9 7 29 27 6 20 35 POWER AMP/POWER SUPPLY IC201 SW1 +10V AU+8V +5V DR+6V A+5V AU+5V D+5V SW2 VP2 VP1 VP SDA SCL STB DIAG DISP;B AU8V U-COM MECHA SERVO CNP101 FL+ FL– RL+ RL– AMP REM ANT REM ATT BATT ILL ACC TEST FR+ 5 6 4 10 2 9 1 12 3 11 FR– RR+ RR– 19 17 18 13 16 14 7 15 X301 32.768kHz X302 6MHz R-CH BATT ILLUMI CHECK Q907 AU +8V +5V REG Q501 TU+5V PJ401 –3 –4 R L AUDIO OUT REAR CN401 (SUB OUT(MONO)) R-CH –5 –6 R L AUDIO OUT FRONT R-CH –1 –2 R L BUS AUDIO IN R-CH 32 FL RL F901 • Signal path : FM : AM/MW : CD EEPROM • R-ch is omitted due to same as L-ch. 24 TEL ATT 69 ILL IN 68 ACC IN 63 TEST IN Q103 ACC DET Q102 MUTE DRIVE Q401,402 AEP,UK,E MODEL CD SECTION 4-3. BLOCK DIAGRAM — TUNER SECTION — (Page 21)

LED CONTROL Q907,908 LCD2 8 9 11 10 4 2 1 3 5 4 6 8 7 BUS INTERFACE IC301 BATT CNP102 (BUS CONTROL IN) 6 13 2 RESET 12 1 BUS ON DATA CLK 3 BATT CHECK X301 30MHz 11 13 XOUT FL ON BATT FL DAT1 FL CLK XIN 23 GCP2 25 GCP1 27 GCP4 28 5 4 2 1 11 GCP3 FL+ 31 SYS CLK 30 SYS SI 29 SYS SO 1 SYS CE INH 7 CNVSS +5V DISP CKO 117 35 33 LCD CE LCD INH 37 36 93 SUB SYSTEM CONTROL IC2 1 2 DISP SO/TX 99 DISP SI/RX 98 DISP CE 95 18 BU IN 65 SYSRST 64 BUS ON 31 UNI SO UNI CKO 29 UNI SI 30 100 CNVSS 7 SIRCS 1 RESET 10 RAM BU 91 FP CTRL 2 MOT- 77 MOT+ 78 I-DET 76 OPEN SW 75 CLOSE SW 74 OPEN KEY 90 SYSTEM CONTROL IC303 (3/3) IC302 RESET MT+B MT+B BATT 1 2 3 MOTOR+B REG IC306 IR RECEIVE IC62 IR RECEIVE IC503 7 7 1 1 KEY IN0 85 KEY IN1 84 RC IN1 70 RC IN0 86 KEY ACK2 87 KEY ACK0 88 KEY ACK1 89 SW501 RESET DIMMER CONTROL Q905 FL POWER CONTROL Q801,802 BATT BATT LED CONTROL Q903,904 DC-DC CONVERTER IC800 KEY IN MATRIX FL 900 T800 FLVDD FL- BATT DET Q101 S932 (RESET) CF 118 CLK 119 DATA DIMMER 120 106 104 105 1 I 103 7 3 I-DET IC308 MOTOR DRIVE IC307 11 6 14 3 12 16 VREF CONTROL Q306,307 I-DET Q305 LED CONTROL Q503,504 SW900 (OPEN/CLOSE) S931 (OPEN) D512 (DISC IN) CNJ101 (REMOTE IN) AEP,UK,E MODEL LED SW1 LED SW2 GCP FL CONTROL IC301 LCD DRIVER IC1 SEG1 I SEG95 COM1 I COM8 21 LAT 22 BK 99 FL DAT2 3 FL DAT3 M601 (OPEN/CLOSE9 D70 D513

SWITCH board LOAD SW board DISPLAY board SERVO board SL SW board MAIN board SUB board 4-5. CIRCUIT BOARDS LOCATION • Waveforms — Servo Board — (MODE: CD PLAY) 1 2Vp-p 2 3.2msec IC1 ts (PACK) 3 IC1 uj (RFO) 4 Approx. 100mVp-p IC1 oa (FEO) 0V 5 Approx. 100mVp-p IC1 od (TEO) 16.9344MHz IC1 wd (XTAL) 5Vp-p 1.2Vp-p 0V • Waveforms — Main Board — (MODE: FM) 1 3.2Vp-p 2 32.768kHz IC303 9 (XOUT) 3 6MHz IC303 qa (OSCOUT) 4.3MHz IC502 4 (OSCD) 1.8Vp-p 3.6Vp-p 1 30MHz IC2 qa (XOUT) 1.5Vp-p • Waveform — Display Board — (MODE: FM) Note: The components identi- fied by mark 0 or dotted line with mark 0 are criti- cal for safety. Replace only with part number specified. Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) for schematic diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • % : indicates tolerance. • f : internal component. • C : panel designation. • A : B+ Line. • Power voltage is dc 14.4V and fed with regulated dc power supply from ACC and BATT cords. • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal produc- tion tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal produc- tion tolerances. • Circled numbers refer to waveforms. • Signal path. F : FM f : AM/MW/LW J : CD • Abbreviation CND : Canadian model for printed wiring boards: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. • x : parts mounted on the conductor side. • a : Through hole. • : Pattern from the side which enables seeing. (The other layer’s patterns are not indicated.) Caution: Pattern face side: Parts on the pattern face side seen from the (Side B) pattern face are indicated. Parts face side: Parts on the parts face side seen from the (Side A) parts face are indicated. • Abbreviation CND : Canadian model

4-6. SCHEMATIC DIAGRAM — CD MECHANISM SECTION — • Refer to page 36 for IC Block Diagram. Note: • Voltage is dc with respect to ground under no-signal conditions. no mark : CD PLAY (Page 31)

1 A B C D E F G H I J 2 3 4 5 6 7 8 9 10 11 12 13 14 CN2

27 27 CDX-M800 1 A B C D E F G H I J 2 3 4 5 6 7 8 9 10 11 12 13 14 SW3 SW2 SW4 SW5 TP8 C45 C4 C26 C37 TP6 TP1 TP2 TP4 TP5 TP87 TP86 TP57 TP77 TP11 TP79 TP83 TP70 TP9 TP27 TP12 TP78 TP10 TP81 TP84 TP54 TP25 TP24 TP37 TP39 TP36 TP38 TP40 TP45 TP22 TP88 TP41 TP46 TP21 TP17 TP20 TP42 TP19 TP28 TP90 C41 TP29 C44 TP73 TP32 TP48 TP71 TP51 TP49 TP52 TP55 TP75 TP53 TP56 TP43 TP58 TP61 TP74 TP68 TP80 TP7 TP62 TP91 TP63 C40 TP66 TP64 TP69 TP72 TP50 TP26 TP3 TP59 TP76 TP18 TP89 TP30 R8 R9 R5 R7 R12 R14 R15 R10 R17 R18 R19 R20 R22 FB1 TP92 C3 C5 C6 C8 C9 C10 C11 C13 C14 C16 C18 C19 C24 C25 C29 C34 C36 C38 C35 C21 C22 C30 C23 C1 C27 R21 TP47 C15 C20 TP35 TP23 C17 TP82 TP44 Q1 R26 TP34 R3 TP16 TP85 IC1 IC2 C43 R30 R29 X1 TP60 CN3 CN1 (Page 29)

(Page 34) (D101) E-10 (D102) E-10 (D103) E-10 (D104) E-10 (D105) E-10 (D106) C-9 (D109) D-9 (D110) B-8 (D111) D-8 (D112) B-8 (D113) D-7 (D114) D-8 (D115) C-8 (D116) D-8 (D117) C-8 (D118) F-9 (D119) F-9 (D120) E-8 (D121) E-8 (D122) B-2 D302 H-9 D303 H-10 D305 I-9 (D401) E-5 (D501) E-2 (D802) I-3 (D803) I-3 (D804) H-2 (D805) H-2 (D806) H-3 D808 J-7 D810 J-7 D819 J-6 (D820) I-4 D825 J-7 D826 J-5 D827 J-7 D828 J-7 D829 J-7 D831 J-6 Ref. No. Location • Semiconductor Location Ref. No. Location ( ): SIDE B (D832) I-8 (D843) I-4 D904 G-7 (D905) F-10 (D907) I-8 D909 D-8 (IC201) B-6 IC301 F-9 (IC302) H-8 IC303 H-8 IC306 H-10 IC307 I-10 (IC308) I-10 IC401 F-3 IC502 F-2 IC800 H-5 (Q101) E-10 (Q102) E-9 (Q103) F-9 Q171 C-4 Q181 C-3 Q271 C-4 Q281 C-3 (Q301) H-8 Q305 I-9 (Q306) H-9 (Q307) G-10 (Q401) F-5 (Q402) E-5 (Q408) E-2 Q470 D-3 (Q501) E-1 (Q801) I-4 (Q802) H-4 Q907 D-8 (Q914) F-11 (Q915) F-10 (Q916) E-10

29 29 CDX-M800 (Page 32) (Page 27) 1 A B C D E F G H I J 2 3 4 5 6 7 8 9 10 11 12 13 14 BATT AEP,UK model US,CND,E model SW900 SW900 D843 Q102 C215 D103 D102 D101 R367 R306 R812 R444 R361 R316 R443 R301 R374 R909 R440 FB101 R304 R307 R201 D105 R332 R950 R312 R310 R845 R308 R303 R328 R305 R311 R309 D104 R356 R323 R357 IC302 R202 R111 R109 Q103 D106 Q914 R104 R110 R105 R908 R103 C402 C307 R107 R102 D110 D114 C316 C202 Q501 C419 D806 R809 D820 C523 D803 D119 D120 Q801 R317 R803 C807 R800 FB301 R805 R520 D805 R808 D121 C313 R339 C334 Q307 C321 Q306 R370 R371 R334 R340 R376 C338 R336 R341 C337 IC308 C304 D111 D401 D113 R801 FB303 Q101 R302 R333 Q402 FB302 D115 D112 C302 R337 C928 R106 R101 R401 R108 L303 R446 D117 R439 R504 Q401 R804 R365 R806 D501 R521 D118 C317 D832 R313 R949 Q408 R424 C420 C501 D802 C522 C442 R505 R866 C506 C505 R502 C315 FB501 R501 R911 R322 C104 R442 Q301 C105 R375 R441 D905 Q916 R343 R366 FB102 R445 C201 D907 R410 R912 R811 Q802 C199 D122 R408 R807 R327 D804 R833 Q915 R402 R503 D116 CNJ101 PJ401 IC201 CNP101 F901 CNP102 CNP301 L101 CNP805 C341 CN401 C103 C312 L301 JW7 JW14 JW2 JW5 JW11 C305 C303 JW13 C223 C309 C214 C212 C311 C226 C306 C308 JW1 C204 D109 JW10 JW16 TUX501 JW9 C221 C401 C301 C434 C435 C433 C418 X501 C425 C102 C502 C203 C432 C503 JW12 TH100 C524 C803 JW6 CN503 X301 C283 C183 C823 JW17 C273 JW4 JW15 C173 C422 C930 JW8 L401 JW18 CNP902 C101 C901 CN904 CN903 C443 JW3 CN601 L302

(detuned) condition. no mark : FM ( ) : AM/MW/LW < > : CD PLAY (Page 31) • Refer to page 24 for Waveform. 4-9. SCHEMATIC DIAGRAM — MAIN SECTION (1/2) — • Refer to page 36 for IC Block Diagrams. IC B/D IC B/D IC B/D D109 D401 D106 D501 D122 R201 R202 R111 R109 R104 R110 R420 R105 R103 R421 D120 D121 Q402 R106 Q401 R422 R407 R419 R424 R501 R285 R275 R243 R175 R418 R143 R185 R408 D909 R242 R142 Q271 Q281 Q171 Q181 L101 R206 R205 R204 R112 R929 R184 R203 R174 R274 R284 R922 R425 C903 C103 R921 R920 C203 C202 C201 C219 C218 C226 C223 C221 C215 C212 R401 C402 C401 C423 C424 C426 C427 C430 C429 C428 C431 C418 C183 C173 C283 C273 C278 C178 C288 C242 C188 C142 C442 C501 C433 C435 C434 R415 C425 R416 R417 R414 C422 C432 C420 C419 C443 C199 Q501 C502 R504 R505 C206 C207 D110 D111 D112 D113 D114 D115 D116 D117 D118 C104 D119 C105 Q103 C102 CN401 CN503 CNP101 F901 R478 C523 C522 R520 C521 C520 R518 IC502 C528 C527 C526 C525 R521 C524 C506 C503 C505 TUX501 PJ401 R445 R446 R442 R441 R443 R439 R444 R440 R272 R282 R172 R182 Q102 IC401 Q408 Q470 R519 X501 R433 R435 R431 R429 L401 IC201 R410 R503 FB501 C204 Q907 R107 R108 C417 C416 C421 R502 R402 C214

C802 C810 CNP102 CNP805 D101 D102 D103 D104 D105 D302 D303 D305 D804 D805 D806 IC306 IC307 IC308 Q306 Q307 Q916 R334 R336 R337 R339 R370 R949 R950 TH100 R364 R350 R328 R356 R357 R102 R809 D820 R800 R805 R324 R808 R320 R318 IC301 R801 R101 R351 R365 R806 D832 R338 C803 R319 R326 Q802 D808 D810 D819 R327 CN601 R367 R301 L303 R376 R375 R374 D826 D829 D827 D828 Q914 D843 R378 R910 R845 D904 D907 R833 IC302 L301 R303 FB102 FB101 C310 C334 C342 C336 C337 C339 C312 C313 R911 C304 C302 C301 C307 C308 C315C316 C320 C319 C901 C928 C807 C809 R804 C317 X301 X302 R335 L800 R807 D803 D802 D825 R915 D831 R811 R866 C823 R812 CNJ101 R346 R323 R322 R372 R316 R373 R325 FB303 C303 R371 R341 R340 C321 C338 C341 C335 R368 R369 CNP902 M601 SW900 CNP301 R313 R908 C309 R909 R901 R306 L302 D901 R311 R906 R361 R912 R902 R312 R903 CNP909 JR300 R366 R343 JR302 JR301 Q301 Q101 R907 R305 R317 R304 R310 R377 R307 FB301 FB302 R302 C318 C322 C323 IC800 T800 Q915 D905 R332 C306 R309 R308 IC303 C311 C101 Q305 R803 C930 C305 R333 Q801 • Refer to page 24 for Waveform. 4-10. SCHEMATIC DIAGRAM — MAIN SECTION (2/2) — • Refer to page 36 for IC Block Diagrams. (Page 35) (Page 33) (Page 25) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM (Page 30) ( ) : AM/MW/LW < > : CD PLAY ∗ : Impossible to measure

(Page 29) Ref. No. Location D506 B-10 D507 B-6 D511 C-8 D512 C-8 D513 E-13 D514 C-10 IC503 B-13 Q503 C-9 Q504 B-10 • Semiconductor Location

Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM (Page 31) IC B/D D506 D507 D511 D512 D513 D514 IC503 Q503 Q504 R531 R532 R533 R536 CN502 R534 C536 C540 C533 C539 C538 R509 R538 C537 FB503 SW501 CN501 C535

(Page 28) 1 A B C D E F G H 2 3 4 5 6 7 8 9 10 11 12 13 14 C962 S909 R954 R981 C907 C904 C960 C908 R984 IC2 C909 C910 FL924 LED909 C961 C983 IC301 R945 R939 R929 R928 FB907 Q904 Q903 FB908 FB909 FB911 FB912 FB913 C901 R956 R906 FL919 FB917 FB904 R994 R964 R967 C964 R968 D908 R944 D902 FB901 R985 C911 R940 FB906 R941 FB925 FB903 FB926 FB905 C914 R947 FB902 R982 D901 R965 R971 FB971 S931 FB914 R969 C905 IC62 C903 R991 FB915 C902 R992 R916 FB916 C913 X301 FL910 FL918 FB923 FB922 FB920 FB921 FB60 R987 R951 R986 S932 C970 LED931 R970 C963 C912 C973 R988 IC1 FL900 R990 LED956 R936 R980 R979 LCD2 R978 R952 R946 Q905 LED911 R955 R959 R957 LED957 R962 R942 R961 R960 R958 R914 R925 R915 R917 R918 R919 R920 R921 R922 R913 R923 R907 R908 R909 R912 R911 R910 R950 LED955 S903 Q908 R901 R902 Q907 LED958 R953 S906 S911 S915 S919 S920 S916 S912 S908 S913 S917 S921 S922 S918 S914 S905 S902 S901 LED902 LED903 LED905 LED906 CNP908 LED908 S904 LED901 LED913 LED915 LED916 LED917 LED919 LED920 LED921 S907 R935 LED922 LED912 D70 Ref. No. Location D70 F-2 D901 B-1 D902 B-4 D908 B-10 IC1 C-8 IC2 B-6 IC62 C-2 IC301 C-7 • Semiconductor Location Ref. No. Location Ref. No. Location Ref. No. Location LED901 F-2 LED902 H-2 LED903 H-1 LED905 F-3 LED906 F-4 LED908 H-4 LED909 A-13 LED911 H-14 LED912 H-12 LED913 H-12 LED915 F-12 LED916 F-12 LED917 F-11 LED919 H-5 LED920 H-9 LED921 H-11 LED922 F-13 LED931 A-2 LED955 F-9 LED956 F-6 LED957 G-4 LED958 G-13 Q903 C-11 Q904 C-10 Q905 F-4 Q907 H-2 Q908 H-2

4-14. SCHEMATIC DIAGRAM — DISPLAY SECTION — • Refer to page 37 for IC Block Diagrams. Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM (Page 31)

4-15. IC BLOCK DIAGRAMS 76 75 AGCI AGCO 74 RFI 73 C3T 72 ASY 71 EFM 70 AVDD 69 7E DAC3 68 7D DAC2 67 7C DAC1 66 7F DAC0 65 MD 64 SD 63 TD 62 FD 60 ATEST 59 TEST1 58 TEST0 57 DGND 56 TSTB 55 TSCK 54 TSI 53 TSO 52 PACK 51 DVDD 61 AGND 1 DGND 2 RFOK 3 RST 4 A0 5 STB 6 SCK 7 SO 8 SI 9 XTALEN 10 DVDD 11 DAVDD 12 ROUT 13 DAGND REGC 16 LOUT 17 DAVDD 18 R+ 19 R– 20 L+ 21 L– 22 XVDD 23 XTAL 24 XTAL 25 XGND 15 14 DAGND 77 RFO 78 EQ2 79 EQ1 80 RF- 81 AGND 82 A 83 C 84 B 85 D 86 F 87 E 88 AVDD 89 REFOUT 90 FE- 91 FEO 92 TE- 93 TEO 94 TE2 95 AGND TEC 96 PD 97 98 LD PN 99 100 AVDD 50 C2D3 49 C2D2 48 C2D1 47 C1D2 46 C1D1 45 DGND 44 PLCK 43 MIRR/WFCK 42 RFCK 41 LOCK 40 DVDD 39 TSOI 38 C16M 37 DGND 36 TX 35 HOLD/WDCK 34 LRCK 33 LRCKIN 32 SCKO 31 SCKIN 30 DOUT 29 28 DIN FLAG 27 EMPH 26 DVDD EFM COMPARATOR EFM EFM DEFECT FOK A3T MIRR FEO TEO TEOFS FEOFS RF AMP BLOCK SWITCH MICROCOMPUTER INTERFACE SCF OSC FOCUS REGISTER TRACKING REGISTER OCTUPLED OVERSAMPLING DIGITAL FILTER NOISE SHAVER OUTPUT BUFFER NOISE SHAVER OUTPUT BUFFER DE-EMPHASIS CIRCUIT D/A INTERFACE CIRCUIT OUTPUT PROCESSOR DIGITAL AUDIO INTERFACE DIGITAL PLL TIMING GENERATOR EFM DEMODULATOR ERROR CORRECTION PROCESSOR MICROCOMPUTER INTERFACE CD-TEXT DECODER SUB-CODE PROCESSOR 16K SRAM D/A AUTO GAIN CONTROLLER FD/TD/SD/MD CONTROLLER ADDER SVDRAM MULTIPLIER SVCRAM SVROM ROM DECODER CLV PROCESSOR DEFECT COMPARATOR RFENV MIRENV A/D CONVERTER MEMORY PROCESSOR COMPARATOR IC502 SAA6588T (MAIN Board (1/2)) IC301 BA8270F (MAIN Board (2/2)) 1 FWD + – + – + – 2 REV LOADING PRE FWD REV 3 LDCONT 6 IN2 7 PREVCC 8 POWVCC VOL– VOL+ IN1 4 PS + – LEVEL SHIFT + – + – LEVEL SHIFT LEVEL SHIFT + – POWER SAVE CH1-4 MUTE X3 9 10 11 VO2– 12 VO2+ 13 VO1– 14 VO1+ 5 BIAS OPIN4+ OPIN4– OPIN3– OPOUT3 MUTE POWVCC GND OPIN3+ OPOUT4 VO3– VO3+ VO4– VO4+ 7.5k 7.5k 16k 16k 7.5k 7.5k 16k 16k 10k 10k 10k 10k 10k 10k 10k 10k 10k 10k 10k 10k + – + – + – LEVEL SHIFT + – + – + – 10k 10k 10k 10k + – 28 27 26 23 22 21 25 20 19 18 17 16 15 24 POWVCC34 (CH3,CH4) PREVCC (PRE.LOADING) POWVCC12 (CH1.CH2) IC2 BA5810FP-E2 (SERVO Board) SCOUT MRO MPTH TCON OSCO OSCI VSSD VDDD DAVN SDA VREF MPX VSSA VDDA AFIN MAD PSWN SCL 2 1 6 15 11 13 16 14 12 INTERFACE REGISTER SIGNAL QUALITY DECODER CLOCKED COMPARATOR POWER SUPPLY & RESET TEST CONTROL OSCILLATOR & CLOCK PAUSE DETECTOR MULTI PATH DETECTOR 57kHz 8th ORDER BAND-PASS FILTER RDS/RDBS DECODER RDS/RDBS DEMODULATOR IIC BUS SLAVE TRANSCEIVER 17 18 CIN 19 LVIN 20 8 7 DATA CLOCK DATA CLOCK 4 4 5 9 10 3 4 5 1 2 3 4 5 6 7 8 9 10 14 13 12 11 BUS ON SWITCH RESET SWITCH BATTERY SWITCH BUSON RST BATT CLK VREF GND VCC RST BUSON CLK-IN B/U-C DATA IN DATA OUT DATA I/O IC307 BA6288FS (MAIN Board (2/2)) IC800 LM2577SX-ADJ (MAIN Board (2/2)) CONTROL LOGIC TSD 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 GND NC OUT1 M BATT VCC CLOSE NC NC RNF NC OUT2 NC VREF OPEN NC NC DRIVER DRIVER POWER SAVE 1 2 3 4 5 SOFT START ERROR AMP 1.25V REF. LOGIC 52kHz OSCILLATION CURRENT LIMIT, THERMAL LIMIT,AND UNDERVOLTAGE SHUTDOWN DRIVER STAGE 2.5V REGULATOR ∑ COMPARATOR CURRENT SENSE VOLTAGE CURRENT SENSE REGISTOR CORRECTIVE RAMP VOLTAGE AMP ERROUT ERRIN GND SWITCH VDD

MUTE MUTE ENABLE LOGIC STANDBY MUTE BATTERY DETECTION CHIP DETECT DIAGNOSTIC PROTECTION DIAGNOSTIC SWITCH REGULATOR SWITCH REFERENCE VOLTAGE LOADDUMP PROTECTION TEMPERATURE PROTECTION BACK-UP SWITCH REGULATOR 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 TAB FL- FL+ RL- RL+ IN_RL SGND IN_RR RR+ RR- FR+ FR- DIAG SW2 SW1 SERVO MECHA VP U-COM SDA SCL VP2 PGND3 SVR IN_FL IN_FR ACGND PGND2 VP1 STB PGND1 RST CRES AU8V GND DISP+B CBU FL RL RR VP FR I2C BUS 16 1 2 3 4 5 6 7 8 15 14 13 11 10 12 9 VIN LIN GND VSTAB VCC NC NC VPO NC GND A VIN VAGC INS VCO NC GND INPUT SLAGE 320kHz AGC 320kHz /500kHz PULSE COUNTER PULSE FORMER NOISE SUPPRESSION BANDGAP REFERENCE IC503 RRX9000-0601 (SUB Board) IC62 RRX9000-0601 (DISPLAY Board)

IC301 TC74VHC32FT(EL) (DISPLAY Board)

mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. SECTION 5 EXPLODED VIEWS Ref. No. Part No. Description Remark 5-1. CHASSIS SECTION Ref. No. Part No. Description Remark NOTE: • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • -XX and -X mean standardized parts, so they may have some difference from the original one. • Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE) ... (RED) Parts Color Cabinet’s Color • Accessories are given in the last of this parts list. • Abbreviation CND: Canadian model R R 1 X-3382-819-1 PANEL (CD) SUB ASSY, SUB (US,CND) 1 X-3382-825-1 PANEL (CD) SUB ASSY, SUB (AEP,UK,E) 2 1-783-268-11 CABLE, FLAT (FFC) 11P 3 1-687-950-11 SUB BOARD 4 3-232-857-01 SHEET (SUB PANEL), ELECTROSTATIC 5 3-248-826-01 COVER (FLEXIBLE) 6 3-230-516-01 SPRING (FLEXIBLE), TENSION 7 3-045-756-01 SCREW (PANEL) 8 1-776-207-72 CORD (WITH CONNECTOR) (POWER) (US,CND,E) 8 1-776-527-71 CORD (WITH CONNECTOR) (ISO) (POWER) (AEP,UK) 9 3-223-913-11 LABEL (OP CAUTION) (AEP,UK,E) 10 3-248-858-01 BRACKET (CD) #1 7-685-790-09 SCREW +PTT 2.6X4 (S) #2 7-685-792-09 SCREW +PTT 2.6X6 (S) 1 3 8 9 10 5 6 2 4 7 7 A A #2 #1 #2 MG-393XC-121//K not supplied not supplied #1 #1

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 51 3-230-495-01 CAM (L) 52 X-3380-549-1 ARM (B-R) ASSY 53 X-3380-544-2 BRACKET (L) ASSY 54 X-3380-548-1 ARM (B-L) ASSY 55 X-3382-822-1 ARM (A-L) ASSY 56 3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT 57 3-045-714-01 GEAR (B) 58 3-342-940-01 WASHER (M) 59 3-045-713-01 GEAR (A) 60 A-3326-298-A SWITCH BOARD, COMPLETE * 61 X-3378-711-4 BRACKET (MOTOR) ASSY 62 3-230-494-01 GEAR (C) 63 3-230-496-01 CAM (R) 64 X-3380-545-2 BRACKET (R) ASSY 65 3-030-909-11 DAMPER, OIL 66 X-3382-823-1 ARM (A-R) ASSY M601 X-3378-769-1 MOTOR ASSY (OPEN/CLOSE) #2 7-685-792-09 SCREW +PTT 2.6X6 (S) #4 7-627-553-28 SCREW, PRECISION +P 2X2.5 #5 7-624-102-04 STOP RING 1.5, TYPE -E #7 7-621-772-18 SCREW +P 2X4 63 64 65 66 52 #2 #7 #2 #5 #5 #5 53 51 54 55 58 59 60 57 56 62 58 61 #2 #2 #2 #2 #4 #5 #5 #5 M601

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 101 3-230-493-01 GEAR (DRIVE SHAFT) 102 3-230-444-01 GUIDE (DRIVE SHAFT) 103 3-040-692-01 RING, CE TYPE RETAINING 104 3-045-721-01 SHAFT, DRIVE 105 3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT 106 A-3274-749-A MAIN BOARD, COMPLETE (US,CND) 106 A-3274-769-A MAIN BOARD, COMPLETE (AEP,UK,E) 107 1-777-246-41 CORD (WITH CONNECTOR) (ANTENNA) 108 1-790-375-22 CORD (WITH CONNECTOR) (SUB OUT (MONO)) F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A TUX501 A-3220-887-A TUNER UNIT (TUX-030) #2 7-685-792-09 SCREW +PTT 2.6X6 (S) #3 7-685-795-09 SCREW +PTT 2.6X12 (S) not supplied F901 TUX501 not supplied not supplied #2 #2 #2 #2 #2 #2 #2 #3 #2 #2 not supplied 101 101 102 102 104 103 103 105 105 106 107 108

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 151 X-3382-818-1 PANEL (KEY) ASSY, FRONT (US,CND) 151 X-3382-824-1 PANEL (KEY) ASSY, FRONT (AEP,UK,E) 152 3-238-816-01 BUTTON (EJECT) 153 3-238-820-01 BUTTON (ENTER) (US,CND) 153 3-238-820-11 BUTTON (ENTER) (AEP,UK,E) 154 3-238-814-01 HOLDER (REFLECTION), BUTTON 155 X-3381-650-1 BUTTON (SEEK/AMS) ASSY 156 3-238-821-01 BUTTON (DISC) 157 3-238-819-01 BUTTON (SOUND) 158 3-238-817-01 BUTTON (DSO) 159 3-238-818-01 BUTTON (MODE) (US,CND) 159 3-238-818-11 BUTTON (MODE) (AEP,UK,E) 160 X-3381-649-1 BUTTON (VOL) ASSY 161 3-238-815-01 BUTTON (CLOSE) 162 3-239-338-01 BUTTON (SOURCE) 163 3-248-825-01 PLATE (FL), GUIDE 164 3-248-791-01 BUTTON (OPEN) 165 3-248-789-01 BUTTON (RESET-DSPL) 166 2-626-869-01 SCREW (M2X3), SERRATION (US,CND) 167 1-687-952-11 FLEXIBLE BOARD 168 X-3381-646-1 BRACKET (PANEL) ASSY 169 A-3274-753-A DISPLAY BOARD, COMPLETE (US,CND) 169 A-3274-766-A DISPLAY BOARD, COMPLETE (AEP,UK,E) 170 3-238-827-01 PLATE (LCD KEY), LIGHT GUIDE 171 3-238-826-01 SHEET (KEY), DIFFUSION 172 1-694-925-11 CONDUCTIVE BOARD, CONNECTION 173 1-694-926-11 CONDUCTIVE BOARD, CONNECTION 174 X-3383-210-1 PANEL (MAIN) ASSY, FRONT FL900 1-518-879-11 INDICATOR TUBE, FLUORESCENT LCD2 1-804-636-21 DISPLAY PANEL, LIQUID CRYSTAL #6 7-685-104-19 SCREW +P 2X6 TYPE2 NON-SLIT 151 152 153 154 155 156 157 158 159 154 160 162 161 163 164 164 174 165 166 FL900 LCD2 not supplied not supplied #6 #6 167 168 169 170 171 172 173

(MG-393XC-121//K) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 201 1-683-283-11 IN SELF SW BOARD 202 3-040-039-03 CHASSIS (T) 203 3-040-038-01 SPRING (LR), TENSION 204 3-040-050-01 LEVER (L) 205 3-040-022-01 RETAINER (ROLLER), SHAFT 206 3-040-044-01 ROLLER (S) 207 3-040-067-01 LEVER (R) 208 A-3301-980-A SHAFT ROLLER ASSY 209 3-040-037-01 GUIDE (DISC) 210 3-040-040-03 ARM (ROLLER) 211 A-3283-233-A SERVO BOARD, COMPLETE 212 3-221-779-02 BRACKET (MOTOR) 213 3-040-034-01 SPRING (RA), TENSION 214 3-040-042-01 WASHER 215 3-043-880-01 RING (RA), RETAINING 216 3-044-206-11 SCREW, SPECIAL 217 1-683-284-11 FLEXIBLE BOARD 218 1-685-337-11 LOAD SW BOARD M903 A-3315-039-A MOTOR SUB ASSY, LO (LOADING) #8 7-627-553-37 SCREW, PRECISION +P 2X3 TYPE3 #9 7-628-253-00 SCREW, SPECIAL #10 7-627-553-17 SCREW, PRECISION +P 2X2 TYPE3 202 204 203 209 201 207 205 205 208 214 214 215 216 206 213 211 210 212 217 218 #8 #8 #9 #9 #9 #8 #10 M903 C C

(MG-393XC-121//K) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 251 3-040-025-02 ARM, CHUCKING 252 3-040-031-01 DAMPER (T) 253 3-040-056-01 LEVER (D) 254 3-040-024-01 RETAINER (DISC) 255 3-040-054-01 WHEEL (LW), WORM 256 3-040-026-01 SPRING (CH), TENSION 257 3-040-032-01 SPRING (FL), COMPRESSION 258 3-040-033-01 SPRING (KF1), TENSION 259 A-3307-422-A CHASSIS (M) COMPLETE ASSY 260 3-040-059-01 SPRING (TR), TENSION 261 3-040-057-01 LEVER (LOCK) 262 3-040-058-01 GEAR (MDL) 263 3-040-052-01 WHEEL (U), WORM 264 3-040-051-02 LEVER (TR) 254 251 256 257 258 260 262 261 259 252 252 252 253 263 257 D D 264 255 not supplied

(MG-393XC-121//K) The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. 301 X-3378-480-1 CHASSIS (OP) ASSY (including M901) 302 3-040-029-01 SPRING (SL), TORSION 303 3-040-045-01 BASE (DRIVING) 304 3-040-194-01 GEAR (MIDWAY) 305 A-3301-983-A SHAFT (FEED) ASSY 306 3-040-030-01 SPRING (FEED), PLATE 307 1-823-641-11 CABLE, FLEXIBLE FLAT (6 CORE) 308 1-683-282-11 SL SW BOARD 309 3-909-607-01 SCREW 0310 8-820-165-06 OPTICAL PICK-UP KSS-721A/C-RP M902 A-3301-985-A MOTOR ASSY, SLED (SLED) #8 7-627-553-37 SCREW, PRECISION +P 2X3 TYPE3 #11 7-627-850-28 SCREW, PRECISION +P 1.4X3 M902 M901 #8 #11 306 309 309 310 305 308 304 303 302 307 301

NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable • Abbreviation CND: Canadian model • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. • CAPACITORS uF : µF • COILS uH : µH Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. When indicating parts by reference number, please include the board. DISPLAY A-3274-753-A DISPLAY BOARD, COMPLETE (US,CND) A-3274-766-A DISPLAY BOARD, COMPLETE (AEP,UK,E) ************************ 1-694-925-11 CONDUCTIVE BOARD, CONNECTION 1-694-926-11 CONDUCTIVE BOARD, CONNECTION 3-238-826-01 SHEET (KEY), DIFFUSION 3-238-827-01 PLATE (LCD KEY), LIGHT GUIDE 3-248-825-01 PLATE (FL), GUIDE < CAPACITOR > C901 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C902 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C903 1-162-959-11 CERAMIC CHIP 330PF 5% 50V C904 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V C905 1-124-778-00 ELECT 22uF 20% 6.3V C907 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C908 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V C909 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V C910 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V C911 1-115-412-11 CERAMIC CHIP 680PF 5% 25V C912 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C913 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C914 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C960 1-162-908-11 CERAMIC CHIP 3PF 0.25PF 50V C961 1-162-907-11 CERAMIC CHIP 2PF 0.25PF 50V C962 1-164-156-11 CERAMIC CHIP 0.1uF 25V C963 1-165-319-11 CERAMIC CHIP 0.1uF 50V C964 1-126-601-11 ELECT 2.2uF 20% 50V C970 1-164-156-11 CERAMIC CHIP 0.1uF 25V C973 1-165-319-11 CERAMIC CHIP 0.1uF 50V C983 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V < CONNECTOR > CNP908 1-774-678-21 CONNECTOR, FPC (ZIF) 24P < DIODE > D70 8-719-083-14 DIODE RRX9000-0501 D901 8-719-978-33 DIODE DTZ-TT11-6.8B D902 8-719-069-54 DIODE UDZS-TE-17-5.1B D908 8-719-056-85 DIODE UDZ-TE-17-8.2B < FERRITE BEAD > FB60 1-500-329-21 INDUCTOR, FERRITE BEAD FB901 1-216-864-11 METAL CHIP 0 5% 1/10W FB902 1-216-864-11 METAL CHIP 0 5% 1/10W FB903 1-216-864-11 METAL CHIP 0 5% 1/10W FB904 1-216-864-11 METAL CHIP 0 5% 1/10W FB905 1-500-329-21 INDUCTOR, FERRITE BEAD FB906 1-500-329-21 INDUCTOR, FERRITE BEAD FB907 1-216-864-11 METAL CHIP 0 5% 1/10W FB908 1-216-864-11 METAL CHIP 0 5% 1/10W FB909 1-216-864-11 METAL CHIP 0 5% 1/10W FB911 1-216-864-11 METAL CHIP 0 5% 1/10W FB912 1-500-329-21 INDUCTOR, FERRITE BEAD FB913 1-500-329-21 INDUCTOR, FERRITE BEAD FB914 1-500-329-21 INDUCTOR, FERRITE BEAD FB915 1-500-329-21 INDUCTOR, FERRITE BEAD FB916 1-500-329-21 INDUCTOR, FERRITE BEAD FB917 1-500-329-21 INDUCTOR, FERRITE BEAD FB920 1-500-329-21 INDUCTOR, FERRITE BEAD FB921 1-500-329-21 INDUCTOR, FERRITE BEAD FB922 1-500-329-21 INDUCTOR, FERRITE BEAD FB923 1-500-329-21 INDUCTOR, FERRITE BEAD FB925 1-500-329-21 INDUCTOR, FERRITE BEAD FB926 1-500-329-21 INDUCTOR, FERRITE BEAD FB971 1-500-329-21 INDUCTOR, FERRITE BEAD < FLUORESCENT INDICATOR > FL900 1-518-879-11 INDICATOR TUBE, FLUORESCENT < JUMPER RESISTOR > FL910 1-216-864-11 METAL CHIP 0 5% 1/10W FL918 1-216-864-11 METAL CHIP 0 5% 1/10W FL919 1-216-864-11 METAL CHIP 0 5% 1/10W FL924 1-216-864-11 METAL CHIP 0 5% 1/10W < IC > IC1 6-701-630-01 IC LC75848T-E IC2 6-802-887-01 IC M30833FJGP-066 IC62 8-759-830-18 IC RRX9000-0601#1 IC301 8-759-523-94 IC TC74VHC32FT(EL) < LIQUID CRYSTAL DISPLAY > LCD2 1-804-636-21 DISPLAY PANEL, LIQUID CRYSTAL < DIODE > LED901 8-719-053-09 LED SML-310VT-T86 (OFF) LED902 8-719-053-09 LED SML-310VT-T86 (SOURCE)

LED905 8-719-053-09 LED SML-310VT-T86 (SCRL) LED906 8-719-053-09 LED SML-310VT-T86 (DSPL) LED908 8-719-053-09 LED SML-310VT-T86 (MODE) LED909 8-719-080-04 LED CL-190UB-X-T (IMAGE) LED911 8-719-053-09 LED SML-310VT-T86 (Z) LED912 8-719-053-09 LED SML-310VT-T86 (DISC –) LED913 8-719-053-09 LED SML-310VT-T86 (ENTER) LED915 8-719-053-09 LED SML-310VT-T86 (LIST) LED916 8-719-053-09 LED SML-310VT-T86 (DISC +) LED917 8-719-053-09 LED SML-310VT-T86 (MENU) LED919 8-719-053-09 LED SML-310VT-T86 (DSO) LED920 8-719-053-09 LED SML-310VT-T86 (EQ7) LED921 8-719-053-09 LED SML-310VT-T86 (SOUND) LED922 8-719-053-09 LED SML-310VT-T86 (TA) (AEP,UK,E) LED931 8-719-080-04 LED CL-190UB-X-T (OPEN) LED955 8-719-076-58 LED NSSW440-BRS (LCD BACK LIGHT) LED956 8-719-076-58 LED NSSW440-BRS (LCD BACK LIGHT) LED957 8-719-079-10 LED CL-220UB-X-TS (VOL) LED958 8-719-079-10 LED CL-220UB-X-TS (SEEK/AMS) < TRANSISTOR > Q903 8-729-106-60 TRANSISTOR 2SB1115A Q904 8-729-900-53 TRANSISTOR DTC114EK Q905 8-729-904-66 TRANSISTOR DTD113EK-T-146 Q907 8-729-216-22 TRANSISTOR 2SA1162-G Q908 8-729-900-53 TRANSISTOR DTC114EK < RESISTOR > R901 1-216-833-11 METAL CHIP 10K 5% 1/10W R902 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R906 1-218-855-11 RES-CHIP 2.2K 2% 1/16W R907 1-218-855-11 RES-CHIP 2.2K 2% 1/16W R908 1-218-851-11 RES-CHIP 1.5K 2% 1/16W R909 1-218-851-11 RES-CHIP 1.5K 2% 1/16W R910 1-218-847-11 RES-CHIP 1K 2% 1/16W R911 1-219-286-11 RES-CHIP 680 2% 1/16W R912 1-219-286-11 RES-CHIP 680 2% 1/16W R913 1-219-286-11 RES-CHIP 680 2% 1/16W R914 1-218-867-11 RES-CHIP 6.8K 2% 1/16W R915 1-218-863-11 RES-CHIP 4.7K 2% 1/16W R916 1-218-859-11 RES-CHIP 3.3K 2% 1/16W R917 1-218-855-11 RES-CHIP 2.2K 2% 1/16W R918 1-218-851-11 RES-CHIP 1.5K 2% 1/16W R919 1-218-851-11 RES-CHIP 1.5K 2% 1/16W R920 1-218-847-11 RES-CHIP 1K 2% 1/16W R921 1-219-286-11 RES-CHIP 680 2% 1/16W R922 1-219-286-11 RES-CHIP 680 2% 1/16W R923 1-219-286-11 RES-CHIP 680 2% 1/16W R925 1-218-871-11 RES-CHIP 10K 2% 1/16W (AEP,UK,E) R928 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R929 1-216-833-11 METAL CHIP 10K 5% 1/10W R935 1-216-033-00 METAL CHIP 220 5% 1/10W R936 1-216-033-00 METAL CHIP 220 5% 1/10W R939 1-216-845-11 METAL CHIP 100K 5% 1/10W R940 1-216-845-11 METAL CHIP 100K 5% 1/10W R941 1-216-845-11 METAL CHIP 100K 5% 1/10W R942 1-216-845-11 METAL CHIP 100K 5% 1/10W R944 1-216-845-11 METAL CHIP 100K 5% 1/10W R945 1-216-048-11 METAL CHIP 910 5% 1/10W R946 1-216-035-11 METAL CHIP 270 5% 1/10W R947 1-216-845-11 METAL CHIP 100K 5% 1/10W R950 1-216-033-00 METAL CHIP 220 5% 1/10W R951 1-216-040-11 METAL CHIP 430 5% 1/10W R952 1-216-035-11 METAL CHIP 270 5% 1/10W R953 1-216-040-11 METAL CHIP 430 5% 1/10W R954 1-216-048-11 METAL CHIP 910 5% 1/10W R955 1-216-040-11 METAL CHIP 430 5% 1/10W R956 1-216-040-11 METAL CHIP 430 5% 1/10W R957 1-216-040-11 METAL CHIP 430 5% 1/10W R958 1-216-040-11 METAL CHIP 430 5% 1/10W R959 1-216-040-11 METAL CHIP 430 5% 1/10W R960 1-216-040-11 METAL CHIP 430 5% 1/10W R961 1-216-040-11 METAL CHIP 430 5% 1/10W R962 1-216-040-11 METAL CHIP 430 5% 1/10W R964 1-218-288-11 METAL CHIP 300 5% 1/10W R967 1-216-805-11 METAL CHIP 47 5% 1/10W R968 1-216-850-11 METAL CHIP 270K 5% 1/10W R969 1-216-846-11 METAL CHIP 120K 5% 1/10W R970 1-216-818-11 METAL CHIP 560 5% 1/10W R971 1-216-009-11 METAL CHIP 22 5% 1/10W R978 1-216-809-11 METAL CHIP 100 5% 1/10W R979 1-216-809-11 METAL CHIP 100 5% 1/10W R980 1-216-809-11 METAL CHIP 100 5% 1/10W R981 1-216-821-11 METAL CHIP 1K 5% 1/10W R982 1-216-841-11 METAL CHIP 47K 5% 1/10W R984 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R985 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R986 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R987 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R988 1-216-035-11 METAL CHIP 270 5% 1/10W R990 1-216-025-11 RES-CHIP 100 5% 1/10W (US,CND) R991 1-218-855-11 RES-CHIP 2.2K 2% 1/16W R992 1-218-855-11 RES-CHIP 2.2K 2% 1/16W R994 1-216-864-11 METAL CHIP 0 5% 1/10W < SWITCH > S901 1-771-884-31 SWITCH, TACTILE (WITH LED) (OFF) S902 1-771-884-31 SWITCH, TACTILE (WITH LED) (SOURCE) S903 1-771-884-31 SWITCH, TACTILE (WITH LED) (CLOSE) S904 1-771-884-31 SWITCH, TACTILE (WITH LED) (VOL –) S905 1-771-884-31 SWITCH, TACTILE (WITH LED) (SCRL) S906 1-771-884-31 SWITCH, TACTILE (WITH LED) (DSPL) S907 1-771-884-31 SWITCH, TACTILE (WITH LED) (VOL +) S908 1-771-884-31 SWITCH, TACTILE (WITH LED) (MODE) S909 1-771-884-31 SWITCH, TACTILE (WITH LED) (IMAGE) S911 1-771-884-31 SWITCH, TACTILE (WITH LED) (Z) S912 1-771-884-31 SWITCH, TACTILE (WITH LED) (DISC –) S913 1-771-884-31 SWITCH, TACTILE (WITH LED) (ENTER) S914 1-771-884-31 SWITCH, TACTILE (WITH LED) (SEEK/AMS > M) S915 1-771-884-31 SWITCH, TACTILE (WITH LED) (LIST) S916 1-771-884-31 SWITCH, TACTILE (WITH LED) (DISC +) S917 1-771-884-31 SWITCH, TACTILE (WITH LED) (MENU)

(SEEK/AMS . m) S919 1-771-884-31 SWITCH, TACTILE (WITH LED) (DSO) S920 1-771-884-31 SWITCH, TACTILE (WITH LED) (EQ7) S921 1-771-884-31 SWITCH, TACTILE (WITH LED) (SOUND) S922 1-771-884-21 SWITCH, TACTILE (WITH LED) (TA) (AEP,UK,E) S931 1-771-884-31 SWITCH, TACTILE (WITH LED) (OPEN) S932 1-771-884-31 SWITCH, TACTILE (WITH LED) (RESET) < VIBRATOR > X301 1-795-818-21 VIBRATOR, CRYSTAL (30MHz) ************************************************************* 1-683-283-11 IN SELF SW BOARD **************** ************************************************************* 1-685-337-11 LOAD SW BOARD *************** ************************************************************* A-3274-749-A MAIN BOARD, COMPLETE (US,CND) A-3274-769-A MAIN BOARD, COMPLETE (AEP,UK,E) ********************* 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT 7-685-792-09 SCREW +PTT 2.6X6 (S) 7-685-795-09 SCREW +PTT 2.6X12 (S) < CAPACITOR > C101 1-126-940-11 ELECT 330uF 20% 16V C102 1-104-942-11 ELECT 1uF 20% 50V C103 1-135-473-21 ELECT 3300uF 20% 16V C104 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C105 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C142 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C173 1-128-428-11 ELECT 10uF 20% 35V C178 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C183 1-128-428-11 ELECT 10uF 20% 35V C188 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C199 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C201 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V C202 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C203 1-124-257-00 ELECT 2.2uF 20% 50V C204 1-124-234-00 ELECT 22uF 20% 16V C206 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V C207 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V C212 1-104-396-11 ELECT 10uF 20% 16V C214 1-104-396-11 ELECT 10uF 20% 16V C215 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V C218 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V C219 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V C221 1-104-396-11 ELECT 10uF 20% 16V C223 1-104-396-11 ELECT 10uF 20% 16V C226 1-104-396-11 ELECT 10uF 20% 16V C242 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C273 1-128-428-11 ELECT 10uF 20% 35V C278 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C283 1-128-428-11 ELECT 10uF 20% 35V C288 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C301 1-128-057-11 ELECT 330uF 20% 6.3V C302 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C303 1-124-584-00 ELECT 100uF 20% 10V C304 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C305 1-124-234-00 ELECT 22uF 20% 16V C306 1-124-234-00 ELECT 22uF 20% 16V C307 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C308 1-104-942-11 ELECT 1uF 20% 50V C309 1-104-942-11 ELECT 1uF 20% 50V C310 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C311 1-128-647-11 DOUBLE LAYERS 1F 5.5V C312 1-124-584-00 ELECT 100uF 20% 10V C313 1-164-156-11 CERAMIC CHIP 0.1uF 25V C315 1-162-918-11 CERAMIC CHIP 18PF 5% 50V C316 1-162-918-11 CERAMIC CHIP 18PF 5% 50V C317 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C318 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V C319 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C320 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C321 1-164-156-11 CERAMIC CHIP 0.1uF 25V C322 1-164-160-11 CERAMIC CHIP 20PF 5% 50V C323 1-162-917-11 CERAMIC CHIP 15PF 5% 50V C334 1-164-156-11 CERAMIC CHIP 0.1uF 25V C335 1-164-156-11 CERAMIC CHIP 0.1uF 25V C336 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C337 1-164-156-11 CERAMIC CHIP 0.1uF 25V C338 1-164-156-11 CERAMIC CHIP 0.1uF 25V C339 1-164-156-11 CERAMIC CHIP 0.1uF 25V C341 1-124-589-11 ELECT 47uF 20% 16V C342 1-164-156-11 CERAMIC CHIP 0.1uF 25V C401 1-124-589-11 ELECT 47uF 20% 16V C402 1-125-889-11 CERAMIC CHIP 2.2uF 10% 10V C416 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C417 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C418 1-104-396-11 ELECT 10uF 20% 16V C419 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V C420 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V C421 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C422 1-124-584-00 ELECT 100uF 20% 10V C423 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C424 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V C425 1-136-154-00 FILM 0.012uF 5% 50V C426 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C427 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C428 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C429 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C430 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V C431 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C432 1-136-154-00 FILM 0.012uF 5% 50V C433 1-104-942-11 ELECT 1uF 20% 50V C434 1-104-942-11 ELECT 1uF 20% 50V C435 1-104-942-11 ELECT 1uF 20% 50V C442 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C443 1-128-428-11 ELECT 10uF 20% 35V C501 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C502 1-104-396-11 ELECT 10uF 20% 16V C503 1-124-259-11 ELECT 4.7uF 20% 16V (AEP,UK,E) IN SELF SW LOAD SW DISPLAY

* CN401 1-506-985-11 PIN, CONNECTOR (PC BOARD) 3P * CN503 1-506-984-11 PIN, CONNECTOR (PC BOARD) 2P * CN601 1-506-985-11 PIN, CONNECTOR (PC BOARD) 3P CNP101 1-774-701-21 PIN, CONNECTOR 16P CNP102 1-580-907-31 PLUG, CONNECTOR (BUS CONTROL IN) CNP301 1-815-260-11 CONNECTOR, BOARD TO BOARD 30P CNP805 1-563-614-31 CONNECTOR, FLEXIBLE 11P * CNP902 1-568-954-11 PIN, CONNECTOR 5P CNP909 1-774-677-21 CONNECTOR, FPC (ZIF) 24P < JACK > CNJ101 1-764-270-11 JACK, STEREO MINIATURE (DIA.3.5) (REMOTE IN) (AEP,UK,E) < DIODE > D101 8-719-083-66 DIODE UDZS-TE-17-18B D102 8-719-083-66 DIODE UDZS-TE-17-18B D103 8-719-420-51 DIODE MA729 D104 8-719-069-56 DIODE UDZS-TE-17-6.2B D105 8-719-083-66 DIODE UDZS-TE-17-18B D106 8-719-978-33 DIODE DTZ-TT11-6.8B D109 8-719-049-38 DIODE 1N5404TU D110 6-500-508-01 DIODE RR263M-400FTR D111 6-500-508-01 DIODE RR263M-400FTR D112 6-500-508-01 DIODE RR263M-400FTR D113 6-500-508-01 DIODE RR263M-400FTR D114 6-500-508-01 DIODE RR263M-400FTR D115 6-500-508-01 DIODE RR263M-400FTR D116 6-500-508-01 DIODE RR263M-400FTR D117 6-500-508-01 DIODE RR263M-400FTR D118 8-719-053-18 DIODE 1SR154-400TE-25 D119 8-719-053-18 DIODE 1SR154-400TE-25 D120 8-719-053-18 DIODE 1SR154-400TE-25 D121 8-719-053-18 DIODE 1SR154-400TE-25 D122 8-719-978-33 DIODE DTZ-TT11-6.8B D302 8-719-914-43 DIODE DAN202K D303 8-719-914-44 DIODE DAP202K D305 8-719-988-61 DIODE 1SS355TE-17 D401 8-719-404-50 DIODE MA111-TX D501 8-719-069-55 DIODE UDZS-TE-17-5.6B D802 8-719-053-18 DIODE 1SR154-400TE-25 D803 8-719-053-18 DIODE 1SR154-400TE-25 D804 8-719-055-30 DIODE D1FS4A-TA D805 8-719-055-30 DIODE D1FS4A-TA D806 8-719-055-33 DIODE D1FL40 D808 8-719-978-33 DIODE DTZ-TT11-6.8B D810 8-719-978-33 DIODE DTZ-TT11-6.8B D819 8-719-978-33 DIODE DTZ-TT11-6.8B D820 8-719-978-33 DIODE DTZ-TT11-6.8B D825 8-719-978-33 DIODE DTZ-TT11-6.8B D826 8-719-978-33 DIODE DTZ-TT11-6.8B D827 8-719-978-33 DIODE DTZ-TT11-6.8B D828 8-719-978-33 DIODE DTZ-TT11-6.8B D829 8-719-978-33 DIODE DTZ-TT11-6.8B D831 8-719-978-33 DIODE DTZ-TT11-6.8B D832 8-719-988-61 DIODE 1SS355TE-17 D843 8-719-978-33 DIODE DTZ-TT11-6.8B D904 8-719-988-61 DIODE 1SS355TE-17 D905 8-719-069-54 DIODE UDZS-TE-17-5.1B D907 8-719-988-61 DIODE 1SS355TE-17 D909 8-719-988-61 DIODE 1SS355TE-17 < FERRITE BEAD > FB101 1-414-813-11 FERRITE, EMI (SMD) (AEP,UK,E) FB102 1-414-813-11 FERRITE, EMI (SMD) (AEP,UK,E) FB301 1-216-295-11 SHORT CHIP 0 FB302 1-216-295-11 SHORT CHIP 0 FB303 1-414-813-11 FERRITE, EMI (SMD) FB501 1-414-813-11 FERRITE, EMI (SMD) (AEP,UK,E) < IC > IC201 6-703-375-01 IC TDA8588J/N1 IC301 8-759-449-89 IC BA8270F-E2 IC302 8-759-658-25 IC PST3432UL IC303 6-802-884-01 IC M30626FHPGP-052 (US,CND) IC303 6-802-885-01 IC M30626FHPGP-053 (AEP,UK,E) IC306 8-759-668-14 IC PQ09DZ1U IC307 8-759-580-33 IC BA6288FS-E2 IC308 8-759-701-01 IC NJM2904M IC401 6-703-303-01 IC TDA7416 IC502 6-703-809-01 IC SAA6588T/V2-518 (AEP,UK,E) IC800 8-759-598-63 IC LM2577SX-ADJ

JR300 1-216-864-11 METAL CHIP 0 5% 1/10W JR301 1-216-864-11 METAL CHIP 0 5% 1/10W (AEP,UK,E) JR302 1-216-864-11 METAL CHIP 0 5% 1/10W (US,CND) < COIL > L101 1-419-476-31 COIL, CHOKE 250uH L302 1-414-185-51 INDUCTOR 22uH (US,CND) L303 1-412-006-31 INDUCTOR 10uH L800 1-424-911-11 COIL, POWER 100uH < JACK > PJ401 1-774-700-11 JACK, PIN 6P (BUS AUDIO IN/AUX-IN, AUDIO OUT REAR/FRONT) < TRANSISTOR > Q101 8-729-900-53 TRANSISTOR DTC114EK Q102 8-729-901-81 TRANSISTOR 2SC2412K-T-146-R Q103 8-729-901-81 TRANSISTOR 2SC2412K-T-146-R Q171 8-729-920-21 TRANSISTOR DTC314TK-T-146 Q181 8-729-920-21 TRANSISTOR DTC314TK-T-146 Q271 8-729-920-21 TRANSISTOR DTC314TK-T-146 Q281 8-729-920-21 TRANSISTOR DTC314TK-T-146 Q301 8-729-901-81 TRANSISTOR 2SC2412K-T-146-R Q305 8-729-901-00 TRANSISTOR DTC124EK Q306 8-729-216-22 TRANSISTOR 2SA1162-G Q307 8-729-901-81 TRANSISTOR 2SC2412K-T-146-R Q401 8-729-900-53 TRANSISTOR DTC114EK Q402 8-729-027-23 TRANSISTOR DTA114EKA-T146 Q408 8-729-053-84 FET SSM3KO9FU(T5LSONY1) Q470 8-729-920-21 TRANSISTOR DTC314TK-T-146 Q501 8-729-106-68 TRANSISTOR 2SD1615A-GP Q801 8-729-054-36 FET UPA1716G-E2 Q802 1-801-806-11 TRANSISTOR DTC144EKA Q907 8-729-901-81 TRANSISTOR 2SC2412K-T-146-R Q914 8-729-027-31 TRANSISTOR DTA124EKA-T146 Q915 8-729-015-11 TRANSISTOR 2SD1802FAST-TL Q916 8-729-901-00 TRANSISTOR DTC124EK < RESISTOR > R101 1-216-835-11 METAL CHIP 15K 5% 1/10W R102 1-216-821-11 METAL CHIP 1K 5% 1/10W R103 1-216-821-11 METAL CHIP 1K 5% 1/10W R104 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R105 1-216-841-11 METAL CHIP 47K 5% 1/10W R106 1-216-841-11 METAL CHIP 47K 5% 1/10W R107 1-216-073-00 RES-CHIP 10K 5% 1/10W R108 1-216-073-00 RES-CHIP 10K 5% 1/10W R109 1-216-833-11 METAL CHIP 10K 5% 1/10W R110 1-216-833-11 METAL CHIP 10K 5% 1/10W R111 1-216-841-11 METAL CHIP 47K 5% 1/10W R112 1-216-821-11 METAL CHIP 1K 5% 1/10W R142 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R143 1-216-833-11 METAL CHIP 10K 5% 1/10W R172 1-216-864-11 METAL CHIP 0 5% 1/10W R174 1-216-809-11 METAL CHIP 100 5% 1/10W R175 1-216-841-11 METAL CHIP 47K 5% 1/10W R182 1-216-864-11 METAL CHIP 0 5% 1/10W R184 1-216-809-11 METAL CHIP 100 5% 1/10W R185 1-216-841-11 METAL CHIP 47K 5% 1/10W R201 1-216-841-11 METAL CHIP 47K 5% 1/10W R202 1-216-809-11 METAL CHIP 100 5% 1/10W R203 1-216-821-11 METAL CHIP 1K 5% 1/10W R204 1-216-821-11 METAL CHIP 1K 5% 1/10W R205 1-216-821-11 METAL CHIP 1K 5% 1/10W R206 1-216-821-11 METAL CHIP 1K 5% 1/10W R242 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R243 1-216-833-11 METAL CHIP 10K 5% 1/10W R272 1-216-864-11 METAL CHIP 0 5% 1/10W R274 1-216-809-11 METAL CHIP 100 5% 1/10W R275 1-216-841-11 METAL CHIP 47K 5% 1/10W R282 1-216-864-11 METAL CHIP 0 5% 1/10W R284 1-216-809-11 METAL CHIP 100 5% 1/10W R285 1-216-841-11 METAL CHIP 47K 5% 1/10W R301 1-216-864-11 METAL CHIP 0 5% 1/10W R302 1-216-864-11 METAL CHIP 0 5% 1/10W R303 1-216-864-11 METAL CHIP 0 5% 1/10W R304 1-216-809-11 METAL CHIP 100 5% 1/10W R305 1-216-809-11 METAL CHIP 100 5% 1/10W R306 1-216-809-11 METAL CHIP 100 5% 1/10W R307 1-216-809-11 METAL CHIP 100 5% 1/10W R308 1-216-809-11 METAL CHIP 100 5% 1/10W R309 1-216-809-11 METAL CHIP 100 5% 1/10W R310 1-216-809-11 METAL CHIP 100 5% 1/10W R311 1-216-809-11 METAL CHIP 100 5% 1/10W R312 1-216-845-11 METAL CHIP 100K 5% 1/10W R313 1-216-845-11 METAL CHIP 100K 5% 1/10W R316 1-216-845-11 METAL CHIP 100K 5% 1/10W R317 1-216-809-11 METAL CHIP 100 5% 1/10W R318 1-216-864-11 METAL CHIP 0 5% 1/10W R319 1-216-821-11 METAL CHIP 1K 5% 1/10W R320 1-216-809-11 METAL CHIP 100 5% 1/10W R322 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R323 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R324 1-216-845-11 METAL CHIP 100K 5% 1/10W R325 1-216-845-11 METAL CHIP 100K 5% 1/10W R326 1-216-853-11 METAL CHIP 470K 5% 1/10W R327 1-216-845-11 METAL CHIP 100K 5% 1/10W R328 1-216-845-11 METAL CHIP 100K 5% 1/10W R332 1-218-871-11 METAL CHIP 10K 0.5% 1/10W (AEP,UK,E) R333 1-216-809-11 METAL CHIP 100 5% 1/10W (AEP,UK,E) R334 1-216-097-11 RES-CHIP 100K 5% 1/10W R335 1-216-837-11 METAL CHIP 22K 5% 1/10W R336 1-216-836-11 METAL CHIP 18K 5% 1/10W R337 1-216-073-00 RES-CHIP 10K 5% 1/10W R338 1-216-837-11 METAL CHIP 22K 5% 1/10W R339 1-216-085-11 RES-CHIP 33K 5% 1/10W R340 1-216-298-00 METAL CHIP 2.2 5% 1/10W R341 1-216-298-00 METAL CHIP 2.2 5% 1/10W R343 1-216-809-11 METAL CHIP 100 5% 1/10W R346 1-216-833-11 METAL CHIP 10K 5% 1/10W

T800 1-439-812-11 TRANSFORMER, DC-DC CONVERTER < THERMISTOR (POSITIVE) > TH100 1-801-792-21 THERMISTOR, POSITIVE < TUNER > TUX501 A-3220-887-A TUNER UNIT (TUX-030) < VIBRATOR > X301 1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz) X302 1-767-419-21 VIBRATOR, CRYSTAL (6MHz) X501 1-579-900-21 VIBRATOR, CRYSTAL (4.3MHz) (AEP,UK,E) *************************************************************

********************** 1-683-284-11 FLEXIBLE BOARD < CAPACITOR > C1 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C3 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C4 1-104-609-11 ELECT CHIP 100uF 20% 4V C5 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C6 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C8 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C9 1-162-924-11 CERAMIC CHIP 56PF 5% 50V C10 1-162-924-11 CERAMIC CHIP 56PF 5% 50V C11 1-162-909-11 CERAMIC CHIP 4PF 0.25PF 50V C13 1-162-916-11 CERAMIC CHIP 12PF 5% 50V C14 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C15 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C16 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C17 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C18 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C19 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C20 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C21 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C22 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C23 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C24 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C25 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C26 1-126-391-11 ELECT CHIP 47uF 20% 6.3V C27 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C29 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C30 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C34 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C35 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C36 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C37 1-126-393-11 ELECT CHIP 33uF 20% 10V C38 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C40 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C41 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C43 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V C44 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C45 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V < CONNECTOR > CN1 1-815-352-11 CONNECTOR, BOARD TO BOARD 30P CN3 1-816-275-21 CONNECTOR, FFC/FPC 6P < JUMPER RESISTOR > FB1 1-216-864-11 METAL CHIP 0 5% 1/10W < IC > IC1 8-759-699-98 IC uPD63711GC-8EU IC2 8-759-658-87 IC BA5810FP-E2 < TRANSISTOR > Q1 8-729-904-87 TRANSISTOR 2SB1197K-R < RESISTOR > R3 1-216-797-11 METAL CHIP 10 5% 1/10W R5 1-218-344-11 METAL CHIP 7.5K 5% 1/10W R7 1-216-839-11 METAL CHIP 33K 5% 1/10W R8 1-216-833-11 METAL CHIP 10K 5% 1/10W R9 1-216-840-11 METAL CHIP 39K 5% 1/10W R10 1-216-835-11 METAL CHIP 15K 5% 1/10W R12 1-216-837-11 METAL CHIP 22K 5% 1/10W R14 1-216-841-11 METAL CHIP 47K 5% 1/10W R15 1-216-841-11 METAL CHIP 47K 5% 1/10W R17 1-216-809-11 METAL CHIP 100 5% 1/10W R18 1-216-809-11 METAL CHIP 100 5% 1/10W R19 1-216-809-11 METAL CHIP 100 5% 1/10W R20 1-216-809-11 METAL CHIP 100 5% 1/10W R21 1-216-821-11 METAL CHIP 1K 5% 1/10W R22 1-216-821-11 METAL CHIP 1K 5% 1/10W R26 1-216-797-11 METAL CHIP 10 5% 1/10W R29 1-216-833-11 METAL CHIP 10K 5% 1/10W R30 1-216-833-11 METAL CHIP 10K 5% 1/10W < VIBRATOR > X1 1-795-520-11 VIBRATOR, CERAMIC (16.9344MHz) ************************************************************* 1-683-282-11 SL SW BOARD ************ ************************************************************* 1-687-950-11 SUB BOARD ********** 1-783-268-11 CABLE, FLAT (FFC) 11P (CN501) < CAPACITOR > C533 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C535 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C536 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C537 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V C538 1-162-959-11 CERAMIC CHIP 330PF 5% 50V C539 1-164-156-11 CERAMIC CHIP 0.1uF 25V C540 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V < DIODE > D506 8-719-069-54 DIODE UDZS-TE-17-5.1B D507 8-719-978-33 DIODE DTZ-TT11-6.8B D511 8-719-083-66 DIODE UDZS-TE-17-18B D512 8-719-079-10 LED CL-220UB-X-TS (DISC IN) D513 8-719-083-14 DIODE RRX9000-0501 D514 8-719-988-61 DIODE 1SS355TE-17 < FERRITE BEAD > FB503 1-500-329-21 INDUCTOR, FERRITE BEAD < IC > IC503 8-759-830-18 IC RRX9000-0601#1 SERVO SL SW SUB

JR552 1-216-864-11 METAL CHIP 0 5% 1/10W < TRANSISTOR > Q503 8-729-216-22 TRANSISTOR 2SA1162-G Q504 8-729-900-53 TRANSISTOR DTC114EK < RESISTOR > R509 1-216-846-11 METAL CHIP 120K 5% 1/10W R531 1-216-833-11 METAL CHIP 10K 5% 1/10W R532 1-216-845-11 METAL CHIP 100K 5% 1/10W R533 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R534 1-216-035-00 METAL CHIP 270 5% 1/10W R536 1-216-288-11 METAL CHIP 300 5% 1/10W R538 1-216-850-11 METAL CHIP 270K 5% 1/10W < SWITCH > SW501 1-692-135-21 SWITCH, KEYBOARD (RESET) ************************************************************* A-3326-298-A SWITCH BOARD, COMPLETE (including SW900) *********************** ************************************************************* MISCELLANEOUS *************** 8 1-776-207-72 CORD (WITH CONNECTOR) (POWER) (US,CND,E) 8 1-776-527-71 CORD (WITH CONNECTOR) (ISO) (POWER) (AEP,UK) 107 1-777-246-41 CORD (WITH CONNECTOR) (ANTENNA) 108 1-790-375-22 CORD (WITH CONNECTOR) (SUB OUT (MONO)) 167 1-687-952-11 FLEXIBLE BOARD 301 X-3378-480-1 CHASSIS (OP) ASSY (including M901) 307 1-823-641-11 CABLE, FLEXIBLE FLAT (6 CORE) 0310 8-820-165-06 OPTICAL PICK-UP KSS-721A/C-RP F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A M601 X-3378-769-1 MOTOR ASSY (OPEN/CLOSE) M902 A-3301-985-A MOTOR ASSY, SLED (SLED) M903 A-3315-039-A MOTOR SUB ASSY, LO (LOADING) ************************************************************* ACCESSORIES ************ 1-476-546-12 REMOTE COMMANDER (RM-X111) (AEP,UK,E) 1-476-546-22 REMOTE COMMANDER (RM-X110) (US,CND) 3-230-549-01 LID, BATTERY CASE (for RM-X110/X111) 3-251-123-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH, SPANISH) (US,CND) 3-251-123-21 MANUAL, INSTRUCTION (ENGLISH,GERMAN, FRENCH,ITALIAN,DUTCH) (AEP,UK) 3-251-123-31 MANUAL, INSTRUCTION (ENGLISH, TRADITIONAL CHINESE) (E) 3-251-125-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH, FRENCH,SPANISH) (US,CND) 3-251-125-21 MANUAL, INSTRUCTION, INSTALL (ENGLISH, GERMAN,FRENCH,ITALIAN,DUTCH) (AEP,UK) 3-251-125-31 MANUAL, INSTRUCTION, INSTALL (ENGLISH, TRADITIONAL CHINESE) (E) ************************************************************* PARTS FOR INSTALLATION AND CONNECTIONS *************************************** 351 X-3382-647-1 FRAME ASSY, FITTING 352 X-3366-405-1 SCREW ASSY (EXP), FITTING (AEP,UK,E) 353 X-3382-821-1 COLLAR ASSY 354 3-934-325-01 SCREW (+K 5X8 TP) (US,CND,E) 355 1-465-459-21 ADAPTOR, ANTENNA (AEP,UK) 356 1-776-207-72 CORD (WITH CONNECTOR) (POWER) (US,CND,E) 357 1-776-527-71 CORD (WITH CONNECTOR) (ISO) (POWER) (AEP,UK) 358 3-246-011-01 KEY (FRAME) The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. SUB SWITCH 351 352 353 354 355 356 357 358 × 2 × 4

Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 1.0 2003. 01 New