Panasonic WV-CL920A Series Operating Instructions Manual

WV-CL924 CL924 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. Model No. WV-CL920A WV-CL924A Color CCTV Cameras Operating Instructions ...

DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The serial number of this product may be found on the top of the unit. You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft. Model No. Serial No. The lightning flash with arrowhead sym- bol, within an equilateral triangle, is intended to alert the user to the pres- ence of uninsulated "dangerous volt- age" within the product's enclosur ...

...

(1) Auto Light Control (ALC)/Electronic Light Control (ELC) (2) Back Light Compensation (Auto: Factory pre- set, Manual: Manual photometric measuring area set) (3) Various External Sync Functions, including Gen-Lock (4) Auto/Manual White Balance Function (5) Electronic Shutter Function 2. Signal-to-noise ratio of 50 dB 3. Minimum illumination of 0.3 lux (0.03 footcandle) with F1.4 lenses (Color mode) 4. Minimum illumination of 0.02 lux (0.002 footcandle) with F1.4 lenses (Black and White mode) 5. 570 lines of horizontal resolution (Black and White mode) 480 lines of horizontal resolution (Color mode) zontal ...

To prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Ask a qualified service person for servicing. 2. Handle the camera with care. Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handling or storage. 3. Do not expose the camera to rain or moisture, or try to operate it in wet areas. Turn the power off immediately and ask a qualified service person for servicing. Moisture can damage the camera and also create the danger of electric shock. 4. Do not use strong or abrasive detergents when cleaning the camera bo ...

WV-CL920 VIDEO OUT GEN-LOCK 120V AC 60Hz VIDEO OUT GEN-LOCK AC 24V IN DC 12V IN GND 2 1 r e !3 !2 !1 !2 !1 q w !0 i y t u o !4 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS Slide the panel to the left until it locks. ...

This connector is used to connect the auto iris lens with a 4-pin male connector supplied as a standard accessory (Part No. YFE4191J100). w Flange-back Adjusting Ring (FB) This ring is used to adjust the back focal length or picture focus. Rotate this ring upward or downward for a CS-mount lens. In case of using a C-mount lens, adjust it with the C-mount adapter. e Focus Fixing Screw (LOCK) r Camera Mounting Screw Hole This hole is used to mount the camera onto a mounting bracket. t Down Button ( ) This button is used to move the cursor downward. It is also used to select items in the CAM SET UP menu. y Right Button ( ) T ...

This socket is used to connect the power cord (supplied as a standard accessory). !4 AC/DC Compatible Input Terminal (DC 12V IN/AC 24V IN) This terminal is for connecting the 12 V DC or 24 V AC power supply cord. Cautions: 1. Connect to 12 V DC (10.5 V-16 V) or 24 V AC (19.5 V-28 V) class 2 power supply only. Make sure to connect the grounding lead to the GND terminal when the power is supplied from a 24 V AC power source. 2. To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for the Input Terminal. ...

1. Plug the AC power cord (supplied as standard accessory) into the AC Inlet Socket. 2. Connect the AC power cord to a 120 V AC 60 Hz outlet. Notes: • Connect the power cord firmly. • The power cord should be long enough for pan- ning and tilting. If the cable is too short, the power cord plug may be pulled off the camera when the camera pans or tilts. B. WV-CL924 (12 V DC/24 V AC) The WV-CL924 has an AC/DC compatible input termi- nal. The 12 V DC or 24 ...

Connect the power cable to the AC/DC compatible input terminal on the rear panel of the camera. Copper wire #24 #22 #20 #18 size (AWG) (0.22 mm2) (0.33 mm2) (0.52 mm2) (0.83 mm2) Length (m) 95 150 255 425 of Cable (Approx.) (ft) 314 495 842 1 403 Recommended wire gauge sizes for 24 V AC line. AC 24V IN DC 12V IN 1 2 GND 24 V AC, 60 Hz (19.5 V - 28 V) Caution: To prevent fire or electric shock hazard,use a UL listed cable (VW-1, style 1007). Video Cable 1. It is recommended to use a monitor whose resolu- tion is at least equal to that of the camera. 2. The maximum extensible coaxial cable length between the camera and the ...

Install the lens connector (YFE4191J100) when using a video drive ALC lens. The installation should be made by qualified service personnel or system installers. (1) Cut the iris control cable at the edge of the lens connector to remove the existing lens connector and then remove the outer cable cover as shown in the diagram below. The pin assignment of the lens connector is as fol- lows: Pin 1: Power source; +9 V DC, 50 mA Max. Pin 2: Not used Pin 3: Video signal; 1.3 V [p-p]/40 kΩ Pin 4: Shield, ground Pin 3 Pin 4 Pin 2 Rib Pin 1 (2) Solder the lens cable to the pins of the supplied connector. ...

The lens mount should be a CS-mount (1”-32UN). In case of a C-mount, it should be a C-mount adapter and the lens weight should be less than 450 g (0.99 lbs). If the lens is heavier, both the lens and camera should be secured by using the supporter. The protrusion at the rear of the lens should be as shown below: CS-mount: Less than 4 mm (5/32”) Screw Flange-back Adjusting Ring w q Mounting the Lens Caution: Before you mount the lens, loosen the fixing screw on the side of the camera, and rotate this ring upward until it stops. If the ring is not at the end, the inner glass or CCD image sensor may be dam- aged. 1. ...

service personnel or system installers. 1. Loosen the screw on the side of the camera. 2. Turn the flange-back adjusting ring to the desired position. Note: Adjusting a focus in the visible rays may be soft-focused with the near-infrared light. 3. Tighten the screws on the side of the camera. Caution: Tightening the screw by force will cause damage to the screw or deviation of focus. FOCUS OR FLANGE-BACK ADJUSTMENT ...

Remove the mount adapter from the bottom of the camera by removing the two fixing screws. Attach the mount adapter to the top as shown in the dia- gram, then mount the camera on the mounting bracket. Make sure that the two original fixing screws are used when mounting the mount adapter as longer length screws may damage inner components. INSTALLATION OF CAMERA ...

This camera utilizes a user setup menu that is displayed on-screen. The setup menu contains various items that form a tree type structure. SETUP Camera ID ON/OFF Light Control ALC ELC Shutter Speed CAM SETUP AGC ON(DNR-H)/ ON(DNR-L)/OFF SYNC INT/LL Camera ID Editing Camera ID Display Position PRESET OFF PRESET OFF PRESET ON (Back Light Compensation) PRESET ON (Back Light Compensation) VBS Automatic Selection VS Automatic Selection LL Manual Selection Manual Mask Area Selection Manual Level Selection Manual Mask Area Selection Manual Level Selection H.Phase SC.Phase Manual Adjustment H.Phase Manual Adjustment V.Phase Manual ...

Motion Detector Special Menu Display Mode CHROMA GAIN UP SIDE DOWN AP GAIN PEDESTAL HUE BW BURST (BW) ON OFF Camera Resetting Manual Mask Area Selection Detection Level Adjustment Lens Drive Signal Selection AUTO1 AUTO2 ON OFF Manual Mask Area Selection DC VIDEO ...

CAM SET UP menu or any other menu is opened, the menu is automatically closed and the mode returns to the normal camera picture. ** CAM SET UP ** CAMERA ID OFF ALC/ELC ALC SHUTTER OFF AGC ON (DNR-H) SENS UP OFF SYNC INT WHITE BAL ATW1 MOTION DET OFF LENS DRIVE DC END SET UP DISABLE ↵ ↵ ↵ Blinking The CAM SET UP menu appears on the monitor as shown above. Check the current settings on the menu. Refer to the sections below for a detailed description of menu items. If you decide not to make any changes after checking the current settings, mov ...

): Moves the cursor upwards. Use this button to select an item or adjust the parameters. Down Button ( ): Moves the cursor downwards. Use this button to select an item or adjust the parameters. Right Button ( ): Moves the cursor to the right. Use this button to select or adjust the parameters of the selected item. The parameter changes each time this button is pressed. 2. SETUP OPERATION This camera utilizes a user setup menu (CAM SET UP) that is displayed on the monitor. To set items on the CAM SET UP menu, use the follow- ing buttons on the side panel. Left Button ( ): Moves t ...

Important Notice: When SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you cannot change the currently active settings. This is to prevent acciden- tal changing of the settings. To edit the CAM SET UP menu (change settings), press and or and to move the cursor to SET UP DISABLE in the bottom line. Press . SET UP DISABLE changes to SET UP ENABLE. Move the cursor to END, then to the item(s) you want to change. Important Notice: When the cursor is moved to END and the CAM SET UP menu closed after changing the parame- ters, the new values are saved in the EEPROM (Electric Erasable and Programmable Read ...

Setting You can use the camera identification (CAMERA ID) to assign a name to the camera. The camera ID consists of up to 16 alphanumeric characters. The camera ID display can be switched on or off on the monitor screen. To edit the CAMERA ID 1. Move the cursor to the CAMERA ID parameter. 2. Press . The CAMERA ID menu appears. The cursor on the letter “0” is highlighted. 3. Move the cursor to the character you want to edit by pressing / / / . 4. After selecting the character, press . The selected character appears in the editing area. (The pointer in the editing area moves to the right automatically at this ...