Panasonic WV-SC384 Operating Instructions Manual

please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual. Operating Instructions Network Camera Model No. WV-SW395, WV-SC385 WV-SC384 WV-SW395E, WV-SC385E WV-SC384E WV-SC385/WV-SC384 WV-SW395 LOCK WV-SC385 OPEN WV-SW395

About notations........................................................ 4 Trademarks and registered trademarks................... 4 Abbreviations........................................................... 5 Viewer software........................................................ 5 Monitor images on a PC............................................... 6 Monitor images from a single camera...................... 6 About the "Live" page.............................................. 8 Monitor images from multiple cameras.................. 13 Monitor images on a cellular phone........................... 14 Record images on the SD memory card manually..... 16 Action at an alarm occurrence................................... 17 Alarm type.............................................................. 17 Action at an alarm occurrence............................... 17 Transmit images onto an FTP server.......................... 18 Transmit an alarm image at an alarm occurrence (Alarm image transmission).................................... 18 Transmit images at a designated interval or period (FTP periodic image transmission)......................... 18 Save images on the SD memory card when images fail to transmit using the FTP periodic image transmission function............................................. 19 Display the log list...................................................... 20 About the log list window....................................... 20 Playback of images on the SD memory card............. 22 About the playback page.................................... 22 Download the images......................................... 24 (When "H.264" is selected for "Recording format" of the SD memory card)...................................... 24 About the network security........................................ 25 Equipped security functions................................... 25 Display the setup menu from a PC............................ 26 How to display the setup menu............................. 26 How to operate the setup menu............................ 27 About the setup menu window.............................. 28 Configure the basic settings of the camera [Basic].... 30 Configure the basic settings [Basic]....................... 30 Configure the settings relating to the SD memory card [SD memory card].......................................... 33 Access copy images saved on the SD memory card onto the PC [SD memory card images].................. 38 Configure the settings relating to the logs [Log].... 43 How the logs and images are saved depending on the settings for "Alarm"....................................... 44 How the logs and images are saved depending on the settings for "Manual/Schedule".................... 45 How the logs and images are saved depending on the settings for "FTP error"................................. 46 Configure the settings relating to images and audio [Image/Audio]............................................................. 47 Configure the settings relating to the aspect ratio [JPEG/H.264].......................................................... 47 Configure the settings relating to JPEG images [JPEG/H.264] (or [JPEG/MPEG-4])......................... 47 Configure the settings relating to H.264 images [JPEG/H.264].......................................................... 49 Configure the settings relating to MPEG-4 images [JPEG/MPEG-4]..................................................... 53 Configure the settings relating to the camera operations [Cam. Function].................................... 56 Configure the settings relating to images and the preset positions [Image/Position]........................... 58 Configure the settings relating to image quality ("Image adjust" setup menu) SW395 SC385 .59 Configure the settings relating to image quality ("Image adjust" setup menu) SC384 ............... 63 Set mask areas.................................................... 66 Configure the settings relating to the preset positions ("Preset position" setup menu)............ 67 Register the preset positions.............................. 68 Configure the settings relating to the auto pan function ("Auto pan" setup menu)....................... 70 Configure the settings relating to the privacy zone ("Privacy zone" setup menu)............................... 71 Configure the settings relating to audio [Audio]..... 72 Configure the multi-screen settings [Multi-screen].... 74 Configure the alarm settings [Alarm].......................... 75 Configure the settings relating to the alarm action [Alarm].................................................................... 75 Configure the settings relating to the camera action on alarm occurrence [Alarm].................................. 76 Configure the settings relating to the alarm image [Alarm].................................................................... 77 Configure the settings relating to H.264 recording [Alarm].................................................................... 78 Configure the settings relating to the alarm output terminal [Alarm]...................................................... 79 Change the AUX name [Alarm]............................... 80 Configure the VMD settings [VMD area]................. 80 Set the VMD areas [VMD area]............................ 82 Configuration of the settings relating to the mail notification [Notification]......................................... 83 Configure the settings relating to Panasonic alarm protocol [Notification]............................................. 84 Configure the setting relating to the image recognition [Advanced func.]........................................................ 85 Configure the settings relating to the XML notification [XML notification].................................................... 85 Configuration of the destination settings of the face detection [XML notification]................................... 85

[User mng.]................................................................. 87 Configure the settings relating to the user authentication [User auth.]..................................... 87 Configure the settings relating to the host authentication [Host auth.]..................................... 88 Configure the settings relating to the priority stream [System]................................................................. 89 Configure the settings of the servers [Server]............ 90 Configure the settings relating to the mail server [Mail]....................................................................... 90 Configure the settings relating to the FTP server [FTP]....................................................................... 91 Configure the settings relating to the NTP server [NTP]....................................................................... 92 Configuring the network settings [Network]............... 93 Configure the network settings [Network].............. 93 Configure the HTTPS settings................................ 99 Generation of the CRT key (SSL encryption key).... 100 Generation of the self-signed certificate (security certificate).......................................................... 101 Generation of CSR (Certificate Signing Request)... 103 Installation of the server certificate................... 104 Configuration of the connection protocol......... 105 Access the camera using the HTTPS protocol.... 106 Install the self-signed certificate (security certificate).......................................................... 106 Configure the settings relating to DDNS [DDNS].111 Configuration of the DDNS service (Example of the "Viewnetcam" service)...................................... 112 When using the "Viewnetcam" service............. 113 Procedure to register information for the "Viewnetcam" service....................................... 114 Checking the information registered for the "Viewnetcam" service....................................... 114 When using "Dynamic DNS Update"................ 115 When using "Dynamic DNS Update(DHCP)".... 115 Configure the settings relating to SNMP [SNMP].116 Configure the settings relating to the FTP periodic image transmission [FTP img. trans.]................... 116 Configure the schedule settings of the FTP periodic image transmission [FTP img. trans.]................... 118 How to set the schedules.................................. 118 How to delete the set schedule........................ 119 Configure the settings relating to the schedules [Schedule]................................................................. 120 Maintenance of the camera [Maintenance].............. 121 Check the system log [System log]...................... 121 Upgrade the firmware [Upgrade].......................... 122 Check the status [Status]..................................... 124 Reset the settings/Reboot the camera [Default reset] 125 Viewing Help............................................................. 126 Displaying the Help screen................................... 126 About the displayed system log............................... 127 Troubleshooting........................................................ 130 Directory structure of drive B................................... 141

There are 2 sets of operating instructions for the WV-SC384, WV-SC385, WV-SW395 (NTSC model), WV-SC384E, WV-SC385E, WV-SW395E (PAL model) as follows. • Installation Guide: Explains how to install and connect devices. When you use the WV-SC385/WV-SC385E or WV-SC384/WV-SC384E, refer to WV-SC385/ WV-SC385E/ WV-SC384/ WV-SC384E Installation Guide. When you use the WV-SW395 or WV-SW395E, refer to WV-SW395/WV-SW395E Installation Guide. • Operating Instructions (PDF): Explains how to perform the settings and how to operate this camera. This Operating Instructions covers the models: WV-SW395, WV-SC385, WV-SC384, WV-SW395E, WV-SC385E, WV-SC384E. Adobe® Reader® is required to read these operating instructions (PDF) on the provided CD-ROM. When the Adobe® Reader® is not installed on the PC, download the latest Adobe® Reader® from the Adobe web site and install it. The model number is abbreviated in some descriptions in this manual. The screens used in these operating instructions show the case of WV-SC385 (NTSC model). About notations The following notations are used when describing the functions limited for specified models. The functions without the notations are supported by all models. SW395 : The functions with this notation are available when using the model WV-SW395. SC385 : The functions with this notation are available when using the model WV-SC385. SC384 : The functions with this notation are available when using the model WV-SC384. Trademarks and registered trademarks • Microsoft, Windows, Windows Vista, Windows Media, Internet Explorer, Active X and DirectX are either regis- tered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. • Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation. • Adobe, the Adobe logo, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. • QuickTime is a trademark of Apple Inc., registered in the U.S. and other countries. • SDHC Logo is a trademark of SD-3C, LLC. • All other trademarks identified herein are the property of their respective owners.

Microsoft® Windows® 7 Professional (64-bit) and Microsoft® Windows® 7 Professional (32-bit) are described as Windows 7. Microsoft® Windows Vista® Business SP1 (32-bit) is described as Windows Vista. Microsoft® Windows® XP Professional SP3 is described as Windows XP. Windows® Internet Explorer® 8.0, Windows® Internet Explorer® 7.0 and Microsoft® Internet Explorer® 6.0 are described as Internet Explorer. SDHC/SD memory card is described as SD card or SD memory card. Universal Plug and Play is described as UPnPTM or UPnP. Viewer software It is necessary to install the viewer software "Network Camera View 4S" to display images on a PC. This software can be installed directly from the camera or by double clicking "nwcv4Ssetup.exe" on the CD-ROM provided, and then following the on-screen instructions. Important: • The default setting of "Automatic installation of Viewer software" is "On". Follow the instructions on page 139 when the message is displayed on the information bar of the browser. • When the "Live" page is displayed for the first time, the install wiz- ard of the ActiveX control required to display images from the cam- era will be displayed. Follow the instructions of the wizard. • When the install wizard is displayed again even after completing the installation of the ActiveX, restart the PC. • The viewer software used on each PC should be licensed individu- ally. The number of installations of the viewer software from the camera can be checked on the [Upgrade] tab of the "Maintenance" page (☞ page 122). Refer to your dealer for the software licensing.

The following are descriptions of how to monitor images from the camera on a PC. Monitor images from a single camera Important: • When the HTTP port number is changed from "80", enter "http://IP address of the camera + : (colon) + port number" in the address box of the browser. (Example: http://192.168.0.11:8080) • When the PC is in a local network, configure the proxy server setting of the web browser (under "Internet Options…" under "Tools" of the menu bar) to bypass the proxy server for the local address. Note: • Refer to "Access the camera using the HTTPS pro- tocol" (☞ page 106) for further information about the case in which "HTTPS" is selected for "HTTPS" - "Connection" on the [Network] tab of the "Network" page. Step 3 Press the [Enter] key on the keyboard. → The "Live" page will be displayed. Refer to page 8 for further information about the "Live" page. When "On" is selected for "User auth.", the authentica- tion window will be displayed before displaying live images for the user name and password entries. The default user name and password are as follows. User name: admin Password: 12345 Step 1 Start up the web browser. Step 2 Enter the IP address designated using the Panasonic IP setup software in the address box of the browser. Example when entering an IPv4 address: http://URL registered using IPv4 address http://192.168.0.10/ Example when entering an IPv6 address: http://URL registered using IPv6 address http://[2001:db8::10]/

password periodically. • When displaying multiple H.264 (or MPEG-4) images on a PC, images may not be displayed depending on the performance of the PC. Note: • When "H.264" is selected for "Video encoding format", H.264 video will be displayed. When "MPEG-4" is selected, MPEG-4 images will be displayed. • The maximum number of concurrent access user is 14 including users who is receiving H.264 (or MPEG-4) images and users who are receiving JPEG images. Depending on the set values for "Bandwidth control (bit rate)" and "Max bit rate (per client) *", the maximum concurrent access number may be less than 14 users. When 14 users are concurrently accessing, the access limit message will be displayed for users who subse- quently attempt to access. When "Multicast" is selected for "Transmission type" of "H.264" (or "MPEG-4"), only the first user who accessed to monitor H.264 (or MPEG-4) images will be included in the maximum number. The second and subsequent users who are monitoring H.264 (or MPEG-4) images will not be included in the maxi- mum number. • When "On" is selected for "H.264 transmission" (or "MPEG-4 transmission") (☞ pages 49 and 53), H.264 (or MPEG-4) images will be displayed. When "Off" is selected, a JPEG image will be displayed. It is possible to dis- play a JPEG image even when "On" is selected for "H.264 transmission" (or "MPEG-4 transmission"). In this case, the refresh interval of JPEG images will be limited to 15 fps SW395 SC385 and 5 fps SC384 . • The refresh interval may become longer depending on a network environment, PC performance, photographic subject, access traffic, etc. When "On" is selected for "H.264 transmission" (or "MPEG-4 transmission"): SW395 SC385 10 fps (1280x960,1280x720,800x600) 15 fps (Other image capture sizes) SC384 5 fps When "Off" is selected for "H.264 transmission" (or "MPEG-4 transmission"): 30 fps

q [Setup] button (*1) Displays the setup menu. The button will turn green and the setup menu will be displayed. w [Live] button Display the "Live" page. The button will turn green and the "Live" page will be displayed. e [Multi-screen] buttons Images from multiple cameras can be displayed on a multi-screen by registering cameras on the setup menu. (☞ Page 13) r [Compression] buttons [H.264]/[MPEG-4] button: The letters "H.264" (or "MPEG-4") on the button will turn green and an H.264 (or MPEG-4) image will be displayed. When "On" is selected for "H.264 transmission" (or "MPEG-4 transmission") of "H.264(1)", "H.264(2)" (or "MPEG-4(1)", "MPEG-4(2)"), the [H.264] (or [MPEG-4]) button will be displayed. (☞ Pages 49 and 53) [JPEG] button: The letters "JPEG" on the button will turn green and JPEG image will be dis- played. t [Stream] buttons These buttons will be displayed only when an H.264 (or MPEG-4) image is displayed. [1] button: The letter "1" will turn green and images in the main area will be displayed in accordance with the setting of "H.264(1)" (or "MPEG-4(1)"). (☞ Pages 49 and 53) [2] button: The letter "2" will turn green and images in the main area will be displayed in accordance with the setting of "H.264(2)" (or "MPEG-4(2)"). (☞ Pages 49 and 53) y [Image capture size] buttons These buttons will be displayed only when a JPEG image is displayed. [VGA] button: The letters "VGA" will turn green and images in the main area will be displayed in VGA size. [QVGA] button: The letters "QVGA" will turn green and images in the main area will be displayed in QVGA size. [1280x960] button: The letters "1280x960" will turn green and images in the main area will be dis- played in 1 280 x 960 (pixels). q w e r t y u i o !0 !1 !2 !3 !4 !7 !8 !9 @0 @1 @2 @3 @4 !5 !6

"800x600" will turn green and images in the main area will be displayed in 800 x 600 (pixels). [640x360] button: The letters "640x360" will turn green and images in the main area will be dis- played in 640 x 360 (pixels). [320x180] button: The letters "320x180" will turn green and images in the main area will be dis- played in 320 x 180 (pixels). [1280x720] button: The letters "1280x720" will turn green and images in the main area will be dis- played in 1 280 x 720 (pixels). Note: • The buttons [VGA], [QVGA], [1280x960] and [800x600]* are displayed only when "4:3(VGA)" or "4:3(800x600)"* is selected for "Aspect ratio". * SW395 SC385 • The buttons [640x360], [320x180] and [1280x720] are displayed only when "16:9" is selected for "Aspect ratio". • When "1280x960" or "1280x720" is selected for the image capture size, it may become smaller than the actual size depending on the window size of the web browser. u [Image quality] buttons These buttons will be displayed only when a JPEG image is displayed. [1] button: Images in the main area will be dis- played in accordance with the setting for "Quality1" of "Image quality setting". [2] button: Images in the main area will be dis- played in accordance with the setting for "Quality2" of "Image quality setting". i [AUX] buttons (*2) These buttons will be displayed only when "AUX output" is selected for "Terminal 3" of "Alarm" on the setup menu. (☞ page 75) [Open] button: The letters "Open" on the button will turn green and the status of AUX connector will be open. [Close] button: The letters "Close" on the button will turn green and the status of the AUX con- nector will be closed. o [Rec. on SD] button (*2) This button will be displayed only when "Manual" is selected for "Save trigger" on the setup menu. (☞ Page 34) Click this button to manually record images on the SD memory card. Refer to page 16 for descriptions of how to manually record images on the SD mem- ory card. !0 [Log] button (*1) [List] button will become available only when "On" is selected for "Save logs" on the setup menu. (☞ Page 43) When this button is clicked, the log list will be dis- played and images saved on the SD memory card can be played. Refer to page 20 for further information about the log list and for how to play images on the SD mem- ory card. !1 [Zoom] buttons (*2) : Click this button to adjust the zoom ratio to the "Wide" side. : Click this button to set the zoom ratio to x1.0. : Click this button to adjust the zoom ratio to the "Tele" side. !2 [Focus] buttons (*2) : Click this button to adjust the focus auto- matically. : Click this button to adjust the focus to the "Near" side. : Click this button to adjust the focus to the "Far" side. Note: • When shooting the following place or the following subjects, focus may not be adjusted automatically. Adjust the focus manually. • Shiny or strongly reflective subject • Subject through the glass with dew or smudge • Two subjects whose distances from the camera are different • Less contrast subject (e.g. white wall) • Horizontal-striped subject such as a window blind • Inclined subject • Dark subject

Select an operation from the pull-down menu and click the [Start] button. The selected operation will start. Click the [Stop] button to stop the operation. The selected operation will stop when the camera (panning/tilting/zooming/focusing) is operated or when an action that is to be taken according to the settings for "Self return" (☞ page 56) or for "Camera action on alarm" (☞ page 76) starts. Auto track SW395 SC385 : Automatically tracks an object in the shooting area. Note SW395 SC385 : • The auto track function works only when the size of the object is larger than 1/300 of the main area and also the contrast ratio between the object and the background is more than 5 %. • The auto track function of this camera is the simpli- fied function that tracks a moving object in the shooting area. It may be impossible to track a mov- ing object in the following cases. • When there are multiple moving objects in the shooting area • When the contrast ratio between a moving object and the background is almost none • When an object moves quickly • When a moving object is too small or too big • When the shooting area is dark • When there is a flicker in the shooting area • When the zoom ratio is set to the TELE side, it may be difficult to obtain accuracy with the auto tracking function. It is recommended to use the auto tracking function with setting the zoom ratio to the "Wide" side. Auto pan: Automatically pans between the start position and the end position set in advance (☞ page 70). Even when the camera is operated for zooming or focusing, the camera continues panning. (However, panning will stop when the zoom but- ton (x1) is clicked.) Preset sequence: Automatically moves to the pre- set positions (☞ page 67) orderly (start from the lowest preset position number). 360 map-shot: Moves 45° horizontally at a time and repeats 7 times to shoot images of each 45° position (45° x 8 = 360°), and then displays 8 thumbnail images of each 45° position (45° x 8 = 360°) on a newly opened window. When a thumbnail image is clicked, the camera moves to the respective position and live images will be displayed on the "Live" page. Preset map-shot: Eight thumbnail images of the preset position 1-8 (☞ page 67) will be displayed orderly on a newly displayed window. When a thumbnail image is clicked, the camera moves to the respective position and live images will be displayed on the "Live" page. Note: • Do not operate the browser until all the thumbnail images are displayed and the camera returns to the original position (where the camera was when "360 map-shot" or "Preset map-shot" was carried out). • When "360 map-shot" is carried out while the cam- era is moving (panning/tilting), images captured while panning/tilting may be displayed as the thumbnail display. In this case, stop the current operation and carry out "360 map-shot" again. • When "Preset map-shot" is carried out with an unregistered preset position (among preset position 1-8), the thumbnail image of the preset position before the unregistered preset position will be dis- played. In this case, the camera will not move when the thumbnail image is clicked. • The camera will not always return to the exactly same position where it was before "360 map-shot" or "Preset map-shot" was carried out. (It may some- times be slightly different.) • The window on which the thumbnail images are dis- played will close when clicking the following buttons that can switch the camera channel or reload images: [Live], [Multi-screen], [H.264], [MPEG-4]/ [JPEG], [Stream], [Image capture size] [Image qual- ity], [Setup]. To display the thumbnail images again, carry out "360 map-shot" or "Preset position map-shot" again.

: Left-click on the control pad to adjust the horizontal/vertical posi- tion of the camera (panning/tilting). Panning/tilting speed will be faster if a clicked point gets farther from the center point of the control pad. It is also possible to pan/tilt the camera by dragging the mouse. Zoom and focus can be adjusted by right-clicking. When an upper/lower area of the control pad is right-clicked, the displayed image will be zoomed in/out on. When a left/right area is right-clicked, the focus will be adjusted to the Near/Far side. Zoom can also be adjusted using the mouse wheel. !5 [Brightness] buttons (*2) Available range: 0 - 255 button: The displayed image will be darker. button: The adjusted brightness will return to the default brightness (64). button: Image will be brighter. !6 [Preset] (*2) Select a preset position from the pull-down menu and click the [Go] button. The camera will move to the selected preset position (☞ page 67). "H" next to the preset position number indicates the home position. When "Home position" is selected, the camera will move to the home position. (☞ Page 56) When "Preset ID" is registered for a preset position, the registered preset ID will be displayed next to the preset position number. !7 Camera title The camera title entered for "Camera title" on the [Basic] tab will be displayed. (☞ Page 30) !8 Alarm occurrence indication button (*2) This button will be displayed and will blink when an alarm has occurred. When this button is clicked, the alarm output terminal will be reset and this button will disappear. (☞ Page 17) !9 Full screen button Images will be displayed on a full screen. To return to the "Live" page, press the [Esc] key. The aspect ratio of displayed images will be adjusted in accordance with the monitor. @0 Snap shot button Click this button to take a picture (a still picture). The picture will be displayed on a newly opened window. When right-clicking on the displayed image, the pop-up menu will be displayed. It is pos- sible to save the image on the PC by selecting "Save" from the displayed pop-up menu. When "Print" is selected, printer output is enabled. Note: • The following setting may be necessary when using Microsoft Windows 7 or Microsoft Windows Vista. Click "Internet Options" on the Tools menu of Internet Explorer, and then click the [Security] tab. Select "Trusted sites", and click "Site". Register the camera address on the "Websites" in the "Trusted sites" window. @1 Mic input button (*3) Turns on/off the audio reception (hear audio from the camera on a PC). This button will be displayed only when "Mic input", "Interactive(Full-duplex)" or "Interactive(Half-duplex)" is selected for "Audio transmission/reception" on the setup menu. (☞ Page 72) When this button is clicked, the button will turn into the button and audio from the camera will not be heard. Audio volume can be adjusted (Low/ Middle/ High) by moving the volume cursor . @2 Audio output button (*3) Turns on/off the audio transmission (play audio from the PC on the unit speaker). This button will be dis- played only when "Audio output", "Interactive(Full- duplex)" or "Interactive(Half-duplex)" is selected for "Audio transmission/reception" on the setup menu. (☞ Page 72) The button will blink during the audio transmission. When this button is clicked, the button will turn into the button and audio from the PC will not be heard. Audio output volume can be adjusted (Low/Middle/ High) by moving the volume cursor .

tion with "Interactive(Half-duplex)" selected, the receiver button and the transmission button will be inoperable for the other users. When "Interactive(Full-duplex)" is selected, the transmis- sion button is inoperable for other users. • Possible duration of audio transmission is up to 5 minutes per transmission. When 5 minutes have passed, the audio transmission will automatically stop. To turn the audio transmission function on, click the [Audio output] button again. • When the camera is restarted, the adjusted volume level (for both the audio transmission and reception) will return to the level that had been set on the [Audio] tab on the setup menu. (☞ Page 73) • Actual volume level will change in three steps even though the volume cursor can be adjusted minutely. @3 SD recording status indicator The status of the SD recording can be checked with this indicator. When the SD recording starts, the SD recording sta- tus indicator will light red. It will go off when the SD recording stops. This indicator will be displayed when "Manual" or "Schedule" is selected for "Save trigger" on the setup menu. (☞ Page 34) @4 Main area (*2) Images from the camera will be displayed in this area. The current time and date will be displayed according to the settings configured for "Time dis- play format" and "Date/time display format". (☞ page 29) In addition, when being adjusted, the status of brightness (☞ page 30), panning/tilting degree and the zoom factor (☞ page 57), and the preset ID (☞ page 68) will be displayed as well as the charac- ters configured for "Camera title on screen" (☞ page 30). The number of lines for the display is 3 when using WV-SW395/WV-SC385, 2 when using WV-SC384. Click a desired point in the main area on the "Live" page that is to be the center of the angle of view. The camera moves to adjust the position in order to set the clicked point as the center. When selecting an area in the main area by drag- ging the mouse, the selected area will be located at the center of the main area. In this case, the zoom ratio will be adjusted automatically. Zoom can be adjusted using the mouse wheel. *1 Only operable by users whose access level is "1. Administrator". *2 Only operable by users whose access level is "1. Administrator" or "2. Camera control" when "On" is selected for "User auth." (☞ Page 87). *3 Operable by users who belong to the access level selected for "Permission level of audio trans./recep." on the [Audio] tab of the "Image/ Audio" page. Refer to page 73 for further infor- mation about the "Permission level of audio trans./recep.". Note: • When operated by a lower access level user, images displayed on the screen may be changed temporar- ily. This does not affect operation of the camera. • When the displayed image is being zoomed in more than 18x, the clicked point may not always be located at the center of the main area. • When the mouse is dragged to move the camera beyond its operable range, the camera will move to the requested direction and will stop at the end of the operable range. Then, the zoom ratio of the dis- played image will automatically be adjusted. • Depending on the PC in use, screen tearing* may occur when the shooting scene drastically changes due to the GDI restrictions of the OS. * A phenomenon in which portions of the screen are displayed out of alignment

→ Images from the registered cameras will be dis- played on a selected multi-screen (screen can be split up to 16 areas). The following are instructions when displaying on a 4-split screen. q To display images on a single screen, click the [Live] button. w Click a camera title. Live images from the camera corresponding to the clicked camera title will be dis- played on the "Live" page of the newly opened win- dow. Monitor images from multiple cameras Images from multiple cameras can be displayed on a multi-screen. Images from 4 cameras (up to 16 cameras) can be displayed simultaneously. To display images on a multi-screen, it is necessary to register cameras in advance. 4 cameras can be registered as a group and up to 4 groups (16 cameras) can be registered. (☞ Page 74) Important: • When displaying images on a 16-screen, panning, tilting and zooming operations become unavailable for images from the Panasonic PTZ cameras. • When displaying images on a 4-screen, panning, tilting and zooming operations become available only for images from the Panasonic PTZ cameras. Refer to the "Readme" file on the provided CD-ROM for further infor- mation about the compatible PTZ cameras and their versions. Or refer to our website (http://panasonic.net/pss/ security/support/info.html) for further information about the supported software. • Only JPEG images with frame by frame playback can be displayed on a multi-screen . Audio will not be heard. • When the power is turned off or the LAN cable is disconnected while displaying images, displaying images on a multi-screen from the "Live" page will become unavailable. • When displaying the image on a multi-screen and "16:9" is selected for "Aspect ratio", the image will be dis- played altered vertically to the aspect ratio of "4:3". q w

It is possible to connect to the camera using a cellular phone via the Internet and monitor images (JPEG only) from the camera on the screen of the cellular phone. It is also possible to refresh images to display the latest image or perform panning, tilting and zooming operations. Important: • When the authentication window is displayed, enter the user name and password. The default user name and password are as follows. User name: admin Password: 12345 To enhance the security, change the password for the user "admin". (☞ page 87) • If the cellular phone in use is not compatible with UTF-8 encode, it is impossible to display the screen correctly. Note: • It is necessary to configure the network settings of the cellular phone in advance to connect to the Internet and monitor images from the camera. (☞ Page 93) Step 1 Access to "http://IP address/mobile"* or "http://Host name registered in the DDNS server/mobile" using a cellular phone. → Images from the camera will be displayed. Note: • When the HTTP port number is changed from "80", enter "http://IP address + : (colon) + port number/ mobile"* in the address box of the browser. • When using the DDNS function, access to "http:// Host name registered in the DDNS server + : (colon) + port number/mobile". • Refer to "Access the camera using the HTTPS pro- tocol" (☞ page 106) for further information about the case in which "HTTPS" is selected for "HTTPS" - "Connection" on the [Network] tab of the "Network" page. • When the authentication window is displayed, enter the user name of an administrator or user and pass- word. Depending on the cellular phone in use, pass- word entry may be required each time the screen is switched. • It is impossible to transmit/receive audio using a cellular phone. • Depending on the cellular phone in use, larger size images may not be displayed. In this case, selecting "Low" for "Image quality setting" of "JPEG" (☞ page 48) may sometimes solve this problem. • Depending on the cellular phone in use or its con- tract plan, it may be impossible to access. * IP address is the global WAN IP address of the rout- er that can be accessed via the Internet. Pan/tilt Zooming control Refresh Resolution control Image quality control Home position AUX control Preset

Pan/tilt * Controls the camera direction. The camera will pan or tilt to each direction by pressing the corresponding dial key. Zooming control * It is possible to perform zooming operations of the camera by pressing "*" or "#". Refresh Refreshes the camera images by pressing the dial key "5". Resolution control Changes the image capture size by pressing the dial key "0". * Image in the aspect ratio of "4:3(VGA)" Changes the image capture size between 320x240 (default) and 640x480. * Image in the aspect ratio of "4:3(800x600)" Changes the image capture size between 320x240 (default) and 640x480. SW395 SC385 * Image in the aspect ratio of "16:9" Changes the image capture size between 320x180 (default) and 640x360. Note: • Some cellular phones cannot change the image capture size even when resolution is changed by resolution control. Image quality control It is possible to change the image quality between "Quality1" and "Quality2" (☞ page 9). Home position * The camera will move to the home position. (☞ page 56) Preset * The camera will move to the designated preset position to display images by pressing the dial key corresponding to the desired channel. (The dial key numbers are not displayed for Preset No 5 or greater. Only preset IDs will be displayed for them.) (☞ Page 68) AUX control * Controls the AUX terminal. These buttons will be displayed only when "AUX output" is selected for "Terminal 3" on the setup menu. (☞ Page 75) * Only displayed for users whose access level is "1. Administrator" or "2. Camera control" when "On" is selected for "User auth." . (☞ page 87)

Images displayed on the "Live" page can be recorded on the SD memory card manually. This button is operable only when "Manual" is selected for "Save trigger" on the [SD memory card] tab of the "Basic" page of the setup menu. (☞ page 34) It is possible to select "JPEG" or "H.264" on "Recording format" of the setup menu. (☞ Page 33) When "JPEG" is selected for "Recording format", still image data are recorded. When "H.264" is selected, video data are recorded. Images recorded on the SD memory card can be copied onto the PC. (☞ Page 38) Step 1 Display the "Live" page. (☞ Page 6) Step 2 Click the [SD] button. → The SD recording window will open. Step 3 Click the [Start] button to start recording images on the SD memory card. The SD recording status indicator will light red (☞ Page 9) while images are being recorded on the SD memory card. The save interval (frame rate) can be configured on the [SD memory card] tab of the "Basic" page. (☞ Page 35) Step 4 Click the [Stop] button to stop saving images on the SD memory card. Step 5 Click the [Close] button to close the window. Note: • It is possible to obtain image data saved on Drive B by clicking the [Execute] button of "Access img." on the [SD memory card] tab and by logging in the camera to access images from the user authentica- tion window. (☞ page 38) The destination directory to which data are to be saved will be a fixed directory on Drive B. Refer to the "Directory structure of drive B" section. (☞ page 141) • When the [Start] button is clicked immediately after the [Stop] button is clicked, saving of images may not start. In this case, click the [Start] button again.

The alarm action (camera action at an alarm occurrence) will be performed when the following alarms occur. Alarm type Terminal alarm: When connecting an alarm device such as a sensor to the EXT I/O connector of the camera, the alarm action will be performed when the connected alarm device is activated. VMD alarm: When motion is detected in the set VMD area, the alarm action will be performed. * VMD stands for "Video Motion Detection". Command alarm: When a Panasonic alarm protocol is received from the connected device via a network, the alarm action will be performed. Action at an alarm occurrence Display the alarm occurrence indication button on the "Live" page (☞ Page 11) The alarm occurrence indication button will be displayed on the "Live" page at an alarm occurrence. Important: • When "Polling(30s)" is selected for "Alarm status update mode" (☞ page 32), the Alarm occurrence indication button will be refreshed in 30-second intervals. For this reason, it may take a maximum of 30 seconds until the alarm occurrence indication button is displayed on the "Live" page at an alarm occurrence. Notify of alarm occurrences to the device connected to the alarm connector It is possible to output signals from the alarm connector on the rear of the camera and sound the buzzer when an alarm occurs. The settings for the alarm output can be configured in the "Alarm output terminal setup" section of the [Alarm] tab of the "Alarm" page. (☞ Pages 75 and 79) Save images on the SD memory card When an alarm occurs, images (JPEG/H.264) will be saved on the SD memory card. The settings to save images on the SD memory card can be configured on the [SD memory card] tab of the "Basic" page (☞ pages 33 and 34) and the [Alarm] tab of the [Alarm] page (☞ page 77). Transmit an image onto a server automatically An alarm image can be transmitted at an alarm occurrence to the server designated in advance. The settings required to transmit an alarm image to a server can be configured in the "Alarm image" section on the [Alarm] tab of the "Alarm" page (☞ page 77) and the [FTP] tab (☞ page 91) of the "Server" page. Important: • Select "FTP error" for "Save trigger" on the [SD memory card] tab when using the SD memory card. When "Alarm input" or "Manual" is selected for "Save trigger", an alarm image will not be transmitted at an alarm occurrence to the FTP server. Notify of alarm occurrences by e-mail Alarm mail (alarm occurrence notification) can be sent at an alarm occurrence to the e-mail addresses registered in advance. Up to 4 addresses can be registered as recipients of the alarm mail. An alarm image (still picture) can be sent with the alarm mail as an attached file. The settings for alarm mail can be configured in the "Mail notification" section on the [Notification] tab of the "Alarm" page (☞ page 83) and the [Mail] tab of the "Server" page (☞ page 90). Notify of alarm occurrences to the designated IP addresses (Panasonic alarm protocol notification) This function is available only when a Panasonic device, such as the network disk recorder, is connected to the system. When "On" is selected for "Panasonic alarm protocol", the connected Panasonic device will be notified that the camera is in the alarm state. The settings for Panasonic alarm protocol can be configured in the Panasonic alarm protocol section of the [Notification] tab of the "Alarm" page. (☞ Page 84)

Images can be transmitted to an FTP server. By configuring the following settings, transmission of images captured at an alarm occurrence or captured at a designated interval to an FTP server will become available. Important: • When using this function, set the user name and the password to access the FTP server to restrict users who can log into the FTP server. • To transmit images to the FTP server, select "Not use" for "SD memory card", or when "JPEG" is selected for "Recording format", select "FTP error" for "Save trigger" on the [SD memory card] tab of the "Basic" page. (☞ page 33) Transmit an alarm image at an alarm occurrence (Alarm image transmission) An alarm image can be transmitted at an alarm occurrence to the FTP server. To transmit alarm images to an FTP server, it is necessary to configure the settings in advance. The settings for the FTP server can be configured on the [FTP] tab of the "Server" page. (☞ Page 91) The alarm image transmission function can be turned on/off in the "Alarm image" section of the [Alarm] tab of the "Alarm" page. (☞ Page 77) Note: • Depending on the network traffic, the number of the transmitted images may not reach the set number of images to be transmitted. • Alarm images failed to be transmitted to the FTP server at an alarm occurrence will not be saved on the SD memory card. However, images that failed to transmit to the FTP server using the FTP periodic image transmis- sion function will be saved. Transmit images at a designated interval or period (FTP periodic image transmission) Images can be transmitted at a designated interval or period. To transmit images at a designated interval or period, it is necessary to configure the settings in advance. The settings for the FTP server can be configured on the [FTP] tab of the "Server" page. (☞ Page 91) It is possible to determine whether or not to use the FTP periodic image transmission function and to configure the settings relating to alarm images and the schedule on the [FTP img. trans.] tab of the "Network" page. (☞ Page 116) Note: • Depending on the line speed or the traffic, images may not be transmitted at the designated interval. • When "On" is selected for both the alarm image transmission function and the FTP periodic image transmission function, the alarm image transmission function will be given priority over the FTP periodic image transmission function. Therefore, images may not be transmitted at the interval designated on the "FTP periodic image trans- mission" setting.

mit using the FTP periodic image transmission function Images that have failed to transmit using the FTP periodic image transmission can be saved automatically on the SD memory card. It is possible to select a trigger to save images on the SD memory card on the [SD memory card] tab of the "Basic" page. (☞ Page 34) To use the SD memory recording function featured in Panasonic’s network disk recorder, select "Off" for "FTP peri- odic image transmission" (☞ page 117) and "FTP error" for "Save trigger" (☞ page 34). Important: • We make no guarantee for any damages of files on the SD memory card incurred by malfunction or error occur- rence in files saved in the SD memory card regardless of what the cause may be. Note: • When browsing images by selecting an FTP error log on the log list, it is necessary to select "On" for "Save logs". (☞ page 43)

The setting items of the cameras will be displayed in list form. • Alarm log: Logs of the alarm occurrences such as time and date of the alarm occurrences and the alarm type will be displayed. • Manual/Schedule log: Logs filed when images have been recorded manually or during the period of the sched- ule on the SD memory card will be displayed. • FTP trans. error log: Logs filed when the FTP periodic image transmission function has failed will be dis- played. Each log list can be displayed only when "On" is selected for "Save logs" on the [Log] tab of the "Basic" page (☞ page 43) respectively. Step 1 Display the "Live" page. (☞ Page 6) Step 2 Click the [List] button. → The log list will be displayed in a newly opened win- dow (log list window). Number of the listed logs Important: • Only a single user can operate the log list window. Other users cannot access the log list window. Note: • When "Not use" is selected for "SD memory card", the "Manual/Schedule log" list and the "FTP trans. error log" list will not be displayed. • When "H.264" is selected for "Recording format" of the SD memory card, the "FTP trans. error log" list will not be displayed. Step 3 Click the desired log type listed below "Log" to display the log list. → The log list of the selected log type will be dis- played. Note: • When any images are saved on the SD memory card, the image can be displayed by clicking Time and Date when "JPEG" is selected for "Recording format" of the setup menu. (☞ Page 33) About the log list window Number of the listed logs Total number of the logs of the selected log type and a number of the log being displayed on the top of the log list will be displayed. Note: • Enter the desired log number and press the [Enter] key on the keyboard. The log of the designated number will be displayed on the top of the log list. [Top] button Click this button to display the log listed at the top.

Click this button to display the previous page of the log list. Note: • When the mouse button is held down while placing the mouse pointer on the [Prev. page] button, the displayed log number will be decremented. When the mouse button is released, the decrement of the log number will stop and the log number displayed at the moment when the mouse button is released will be the top of the currently displayed page. [Next page] button Click this button to display the next page of the log list. Note: • When the mouse button is held down while placing the mouse pointer on the [Next page] button, the displayed log number will be incremented. When the mouse button is released, the increment of the log number will stop and the log number displayed at the moment when the mouse button is released will be the top of the currently displayed page. [Last] button Click this button to display the log listed at the bottom. [Time & date] Time and date when each log has been filed will be dis- played. Note: • When "Off" is selected for "Time display format" (☞ page 30), time and date of alarm occurrence will be displayed in 24-hour format. • The recording timing of logs is as follows. Alarm log: Alarm occurrence time and date will be filed as a log. Manual/Schedule log: Time and date when record- ing of images onto the SD memory card started manually or during the period of the schedule will be filed as a log. When JPEG images are recorded sequentially, logs will be filed every one hour. FTP trans. error log: Logs will be filed every one hour. [Event] The event type will be displayed. The event types will be displayed only when displaying the alarm log list. TRM1: Alarm by alarm input to Terminal 1 TRM2: Alarm by alarm input to Terminal 2 TRM3: Alarm by alarm input to Terminal 3 VMD: Alarm by VMD alarm COM: Alarm by command alarm [SD memory card] Available capacity and the original capacity of the SD memory card will be displayed. The displayed descriptions are the same descriptions displayed as "Remaining capacity" on the [SD memory card] tab. (☞ Page 36) [Delete] button Click this button to delete the currently displayed log list. When using the SD memory card, images associated with the log list will also be deleted. Important: • If there are too many recorded data files, it may take time to delete all of them. (When the total size of the JPEG files is 1 GB, it may require around 1 hour.) Formatting the SD memory card can shorten the time to delete all the data. (☞ Page 36) • In the process of the deletion, only logs will be saved, and it is impossible to save images newly. • Do not turn off the power of the camera until the deletion is complete. When the power of the camera is turned off in the process of the deletion, some images may remain on the SD memory card. In this case, click the [Delete] button on the same log list window used to delete the logs. [Download] button Click this button to download all logs of the selected log list as a file onto the PC. [Close] button Click this button to close the log list window.

When clicking a time and date listed on the log list window, the "Live" page will turn to the "Playback" page. When images associated with the clicked time and date are on the SD memory card, the first image of them will be displayed. Important: • This function is available only when "JPEG" is selected for "Recording format" of the SD memory card. When "H.264" is selected, the "Playback" page will not be displayed. However, images can be downloaded. Refer to page 24 for descriptions of how to operate. • Refresh interval of images may become slow during playback or download. • When many images are saved on the SD memory card, it may take time to display images on the "Playback" page. • Even when the size of the images saved on the SD memory card is "QVGA", "800x600"* or "1280x960", the images will be played back in VGA size on the playback page. When "16:9" is selected for the "Aspect ratio", images will be displayed in an image capture size of "640x360", even "320x180" or "1280x720" is selected. Therefore, images may look coarse on the "Playback" window. * SW395 SC385 • When playing images by selecting an FTP error log on the log list, images may not be played in order of images recorded on the SD memory card if they have been recorded on the SD memory card with selected value for the "Transmission interval" setting on the [FTP img. trans.] tab is "1 min" or less. About the playback page Number of images When clicking a time and date listed on the log list win- dow, total number of images associated with the clicked time and date, and the number of the currently displayed image will be displayed. Note: • Enter the desired number of image and press the [Enter] key on the keyboard. The image of the des- ignated number will be displayed. Number of images [REW] button Each time the button is clicked, the playback speed will change. When the [PLAY] button or the [REV PLAY] button is clicked during fast playback/fast reverse playback, playback speed will return to the normal playback speed. [REV PLAY] button Images will be played in reverse sequential order.

mouse pointer is on this button, the image number will be incremented. When the mouse button is released, the increment of the image number will stop and the image num- ber displayed at the moment when the mouse but- ton is released will be displayed. [LAST] button The last image will be displayed. ■ SD card [Start] button The selected image will be downloaded onto the PC. Before downloading images, designate the destination directory in advance. (☞ Page 43) The following window will be displayed when the [Start] button is clicked. Select the image to be downloaded, and then click the [OK] button. All: All images saved at the selected time and date will be downloaded. Current image: Only the currently displayed image will be downloaded. Download range: Images in the designated range of number of images will be downloaded. Note: • When the [Cancel] button is clicked in the process of the download, the download will be canceled. In this case, images already downloaded before clicking the [Cancel] button will be saved on the PC. [Browse] button When successfully logged in after the user authentica- tion process, a folder on the SD memory card in which images are saved will be displayed. (☞ Page 38) [PLAY] button When this button is clicked, images will be played in sequential order. [FF] button Each time the button is clicked, the playback speed will change. When the [PLAY] button or the [REV PLAY] button is clicked during fast playback/fast reverse playback, playback speed will return to the normal playback speed. [TOP] button The first image will be displayed. [PREV IMAGE] button The previous frame will be displayed and paused when this button is clicked during playback. Each time this button is clicked during pausing, the frame previous to the currently displayed frame will be displayed. Note: • When the mouse button is held down while the mouse pointer is on this button, the image number will be decremented. When the mouse button is released, the decrement- ing of the image number will stop and the image corresponding to the currently displayed number will be displayed. [PAUSE] button Playback will be paused when this button is clicked during playback. Playback will resume when this button is clicked during pausing. [STOP] button Playback will stop and the "Playback" window will turn to the "Live" page. [NEXT IMAGE] button The next frame will be displayed and paused when this button is clicked during playback. Each time this button is clicked during pausing, the frame next to the currently displayed frame will be dis- played.

(When "H.264" is selected for "Recording format" of the SD memory card) Important: • Depending on the network environment, download of video data may fail. To play back video data recorded on the SD memory card, download the desired data, and save the data on the PC. It is impossible to play back video data on the "Playback" page. For this reason, follow the procedure below. Step 1 Click the time & date on the log list window. (☞ Page 20) → The message window will be displayed to ask if it is OK to start download. Step 2 Select the image to be downloaded, and then click the [OK] button. → Image saved at the clicked time and date will be downloaded. Note: • When the [Cancel] button is clicked in the process of the download, the download will be canceled. In this case, images already downloaded before click- ing the [Cancel] button will be saved on the PC. • Downloading of the associated video data will be started. Before downloading images, designate the destination directory in advance. (☞ Page 43) * When the [Cancel] button is clicked after the download is started, it may take time to cancel the download. * Video data are saved in the files of approx. 2 MB. When the file size of video data is more than 2 MB, two or more files will be downloaded. It is possible to play back video data saved on the PC using such applications as QuickTime® Player or Windows Media® Player*1. However, we are not lia- ble for performance relating to these applications. *1 The supported operating system is Microsoft® Windows® 7 only. • Depending on the status of the SD memory card, QuickTime Player, or Windows Media Player, video data cannot be played back.

Equipped security functions The following security functions are featured in this camera. q Access restrictions by the host authentication and the user authentication It is possible to restrict users from accessing the camera by setting the host authentication and/or the user authentication to "On". (☞ Pages 87 and 88) w Access restrictions by changing the HTTP port It is possible to prevent illegal access such as port scanning, etc. by changing the HTTP port number. (☞ Page 94) e Access encryption by the HTTPS function It is possible to enhance the network security by encrypting the access to cameras using the HTTPS function. (☞ Page 99) Important: • Design and enhance security countermeasures to prevent leakage of information such as image data, authenti- cation information (user name and password), alarm mail information, FTP server information, DDNS server information, etc. Perform the countermeasure such as access restriction (using the user authentication) or access encryption (using the HTTPS function). • After the camera is accessed by the administrator, make sure to close the browser for added security. • Change the administrator password periodically for added security. Note: • When user authentication (authentication error) has failed to pass 8 times within 30 seconds using the same IP address (PC), access to the camera will be denied for a while.

The settings of the camera can be configured on the setup menu. Important: • The setup menu is only operable by users whose access level is "1. Administrator". Refer to page 87 for how to configure the access level. How to display the setup menu Step 1 Display the "Live" page. (☞ Page 6) Step 2 Click the [Setup] button on the "Live" page. → The window with the user name and password entry fields will be displayed. Step 3 Click the [OK] button after entering the user name and the password. → The setup menu will be displayed. Refer to page 28 for further information about this menu.

Setup page Menu buttons Step 1 Click the desired button in the frame on the left of the window to display the respective setup menu. When there are tabs at the top of the setup page dis- played in the frame on the right of the window, click the desired tab to display and configure the setting items relating to the name of the tab. Step 2 Complete each setting item displayed in the frame on the right of the window. Step 3 After completing each setting item, click the [Set] but- ton to apply them. Important: • When there are two or more [Set] and [Execute] but- tons on the page, click the respective button to the edited setting item. When completing the setting items in field A, click the [Set] button (A-1) below field (A). The edited settings in field A will not be applied unless the [Set] button (A-1) below field (A) is clicked. In the same manner as above, click the [Set] button (B-1) below field B when completing the setting items in field B. A B B-1 A-1

q [Setup] button Display the "Setup" page. w [Live] button Display the "Live" page. e [Basic] button Displays the "Basic" page. The basic settings such as time and date and camera title, and the settings relating to the SD memory card can be configured on the "Basic" page. (☞ Page 30) r [Image/Audio] button Displays the "Image/Audio" page. The settings relating to image quality, image capture size and camera actions of JPEG/H.264 (or MPEG-4) camera images can be configured on the "Image/Audio" page. (☞ Page 47) t [Multi-screen] button Displays the "Multi-screen" page. The cameras from which images are to be displayed on a multi-screen can be registered on the "Multi-screen" page. (☞ Page 74) y [Alarm] button Displays the "Alarm" page. The settings relating to alarm occurrences such as settings for the alarm action at an alarm occurrence, the alarm occurrence notification, and the VMD area settings can be con- figured on the "Alarm" page. (☞ Page 75) u [Advanced func.] button Displays the "Advanced func." page. The setting relating to the XML notification, destinations of information about the face detection and the set- tings relating to the face detection can be config- ured on the "Advanced func." page. (☞ Page 85) i [User mng.] button Displays the "User mng." page. The settings relating to the authentication such as users and PCs restric- tions for accessing the camera can be configured on the "User mng." page. (☞ Page 87) o [Server] button Displays the "Server" page. The settings relating to the mail server, the FTP server and the NTP server to which the camera accesses can be configured on the "Server" page. (☞ Page 90) !5 Setup page !4 Camera title w [Live] button q [Setup] button e [Basic] button r [Image/Audio] button t [Multi-screen] button y [Alarm] button u [Advanced func.] button i [User mng.] button o [Server] button !0 [Network] button !1 [Schedule] button !2 [Maintenance] button !3 [Help] button

and the settings relating to DDNS (Dynamic DNS), SNMP (Simple Network Management Protocol) and the FTP (File Transfer Protocol) periodic transmis- sion can be configured on the "Network" page. (☞ Page 93) !1 [Schedule] button Displays the "Schedule" page. On the "Schedule" page, it is possible to designate time zones to allow to receive alarm input or to allow to activate the VMD detection function. (☞ Page 120) !2 [Maintenance] button Displays the "Maintenance" page. System log check, firmware upgrade, status check and initial- ization of the setup menu can be carried out on the "Maintenance" page. (☞ Page 121) !3 [Help] button Displays the "Help" page. (☞ Page 126) !4 Camera title The title of the camera whose settings are currently being configured will be displayed. !5 Setup page Pages of each setup menu will be displayed. There are tabs for some setup menus. When the under- lined item is clicked, the corresponding help page will be displayed.

The basic settings such as camera title, time and date, SD memory card and the logs can be configured on the "Basic" page. The "Basic" page has 3 tabs; the [Basic] tab, the [SD memory card] tab and the [Log] tab. Configure the basic settings [Basic] Click the [Basic] tab on the "Basic" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The settings such as the camera title, time and date, etc. can be configured on this page. [Camera title] Enter the title of the camera. Click the [Set] button after entering the title of the camera. The entered title will be displayed in the "Camera title" field. Available number of characters: 0 - 20 characters Unavailable characters: "& Default: Varies as follows depending on the model in use. WV-SC384 WV-SC385 WV-SW395 [Date/time] Enter the current time and date. When "12h" is selected for "Time display format", "AM" or "PM" can be selected. Available range: 01/01/2010 00:00:00 - 31/12/2035 23:59:59 Important: • Depending on the conditions such as the ambient temperature and operating period, the configured time & date may not be accurate. • Use an NTP server when the more accurate time & date setting is required for the system operation. (☞ Page 92) [Time display format] Select the time display format from "24h", "12h" and "Off". Enter the current hour reflecting this setting when entering the current time and date for "Date/time". To hide time and date, select "Off". Default: 24h [Date/time display format] Select a date/time display format. When "2010/04/01 13:10:00" is set for "Date/time" after selecting "24h" for "Date/time display format", time & date will be respec- tively displayed as follows. DD/MM/YYYY: 01/04/2010 13:10:00 MM/DD/YYYY: 04/01/2010 13:10:00 DD/Mmm/YYYY: 01/Apr/2010 13:10:00 YYYY/MM/DD: 2010/04/01 13:10:00 Mmm/DD/YYYY: Apr/01/2010 13:10:00 Default: DD/MM/YYYY (PAL model) Mmm/DD/YYYY (NTSC model) [Summer time (daylight saving)] Select "In", "Out" or "Auto" to determine whether or not to apply daylight saving time. Configure this setting if the summer time (daylight saving time) is applied in the location where the camera is in use. In: Applies summer time. An asterisk (*) will be dis- played on the left side of the displayed time and date. Out: Does not apply summer time. Auto: Applies summer time in accordance with the set- tings for "Start time & date" and "End time & date" (month, week, day of the week, time). Default: Out [NTP/Time zone] When "NTP" is clicked, the [NTP] tab of the "Server" page will be displayed. (☞ Page 92)

When "Auto" is selected for "Summer time(daylight saving)", select the time & date for the start time and the date time (month, week, day of the week, time). [Camera title on screen] Select "On" or "Off" to determine whether or not to dis- play the camera title on the screen. When "On" is selected, the character string entered for "Camera title on screen (0-9, A-Z)" will be displayed at the position selected for "OSD position". Default: Off Note SC384 : • When moving the camera to a preset position, the characters configured for "Camera title on screen" will be deleted, and the preset ID will be displayed instead. [Camera title on screen (0-9, A-Z)] Enter a character string to be displayed on the image. Available number of characters: 0 - 20 characters Available characters: 0-9, A-Z and the following marks. !"# $% &'()*+,-./:; =? Default: None (blank) [OSD position] Select the position where the time and date and a char- acter string to be displayed on the image of the "Live" page. Upper left: The above information will be displayed at the upper left corner of the main area on the "Live" page. Lower left: The above information will be displayed at the lower left corner of the main area on the "Live" page. Upper right: The above information will be displayed at the upper right corner of the main area on the "Live" page. Lower right: The above information will be displayed at the lower right corner of the main area on the "Live" page. Default: Upper left [Character size] SW395 SC385 Select the size of the entered character string to be dis- played at the selected OSD position in the screen of the "Live" page. Large: The character size will become large size. Middle: The character size will become standard size. Small: The character size will become small size. Default: Middle Note: • "Small" will be set for WV-SC384, WV-SC384E. [Brightness status display] Select "On" or "Off" to determine whether or not to dis- play the status of brightness on images displayed on the "Live" page when adjusting brightness. Default: On [Indicator] Determine whether or not to use the following indica- tors. • Link indicator • Access indicator • Live indicator On: All the indicators will light in accordance with the status. On(Access): Only the live indicator will light when images are viewed. Off: All the indicators will light off. Default: On Note: • Link indicator (orange): This indicator will light when communication with the connected device is available. • Access indicator (green): This indicator will light when accessing a network. • Live indicator (Red/Orange/Green): The live indi- cator will light or blink as follows depending on the camera status.

turned on Before the net- work connection is established Blinks orange When the network connection is established Blinks orange → Blinks green → Lights green During the standby or connection (Cable is not connected.) Lights orange During standby or connection (Cable is connected.) Lights green During the upgrade process Blinks orange During the initialization Blinks orange → Lights off Port forwarding error caused by the UPnP function Blinks orange (in 2 seconds intervals (on for 1 second / off for 1 second)) Trouble happening on the camera Blinks red Failure in writing data on the SDHC/SD memory card Lights red [Alarm status update mode] Select an interval of the camera status notification from the following. When the status of the camera changes, the alarm occurrence indication button, the [AUX] button or the SD saving status indicator will be displayed to notify of the camera status. Polling(30s): Updates the status each 30 seconds and provide notification of the camera status. Real time: Provide notification of the camera status when the status has changed. Default: Real time Note: • Depending on the network environment, notification may not be provided in real time. [Alarm status reception port] When selecting "Real time" for "Alarm status update mode", designate a port number to which the status change notification is to be sent. Available port number: 1 - 65535 Unavailable port number: Refer to the help window. Default: 31004 [Automatic installation of viewer software] Determine whether or not to install the viewer software from this camera. On: Installs the viewer software from the camera auto- matically. Off: The viewer software cannot be installed from the camera. Default: On Important: • It is impossible to display images and to receive/ transmit audio between the camera and the PC when the viewer software "Network Camera View 4S" is not installed on the PC. • The number of the viewer software installations can be checked on the [Upgrade] tab of the "Maintenance" page.

memory card] Click the [SD memory card] tab on the "Basic" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The settings relating to the SD memory card can be configured on this page. ■ SD memory card [SD memory card] Select "Use" or "Not use" to determine whether or not to use the SD memory card. Default: Use Important: • Select "Not use" when operating without a SD memory card. • When the setting is changed between "Use" and "Not use" while another user is during operation, the operation will be canceled. • Before removing the SD memory card from the camera, it is necessary to select "Not use" first. • After inserting the SD memory card, it is necessary to select "Use" to use the SD memory card. • When playing or downloading images saved on the SD memory card, it is necessary to select "On" for "Save logs" on the [Log] tab (☞ page 43) in advance. • When the image refresh interval is short, notifica- tion/recording timing or interval may become incor- rect. Notification/recording may also not be per- formed correctly as configured when multiple users are receiving images. In this case, set the refresh interval longer. • There are limited times to overwrite on an SD mem- ory card. When having a high frequency of overwrit- ing, the lifetime of the SD memory card may become shorter. • A lifetime of a SD memory card should be influ- enced by the number of the image files stored and log savings on the SD memory card. Selecting H.264 for "Recording format" can reduce the num- ber of files to be stored on the SD memory card. • The data writing speed will go down after data are repeatedly written down on an SD memory card. [Recording format] Select "JPEG" or "H.264" for the video encoding format of image data to be recorded on the SD memory card. JPEG: Records still image data. H.264: Records video data in the MP4 video encoding format. Audio will not be recorded. Default: JPEG Note: • When "H.264" is selected, it will become impossible to transmit images with the settings of MPEG-4 or H. 264(2). • When "H.264" is selected, the settings for "H.264(2)" on the [JPEG/H.264] tab of the "Image/ Audio" page will be changed to the settings for "H.264 recording". • When the setting value of "Video encoding format" on the [JPEG/H.264] tab of the "Image/Audio" page is changed from "H.264" to "MPEG-4", the setting value of "Recording format" will automatically be changed to "JPEG".

be maintained if "H.264/MPEG-4(2)" is selected for "Priority stream" - "Stream type" on the [System] tab of the "User mng." page. • When using the SD memory recording function of a Panasonic’s network disk recorder, select "JPEG" for "Recording format". • When the setting of "Recording format" is changed between "JPEG" and "H.264", format the SD mem- ory card. (☞ Page 36) • Due to the difference in file formats, the indication of remaining capacity of the SD memory card differs between the cases when "JPEG" is selected and when "H.264" is selected for "Recording format". • When "H.264" is selected for "Recording format", the following settings in "H.264 recording"; "Image capture size", "Frame rate*", "Max bit rate", "Image quality", and "Refresh interval" will be read from the settings in "H.264(2)". When "2s", "3s", "4s" or "5s" is selected for "Refresh interval" of "H.264(2)", "Refresh interval" for "H.264 recording" will be set to "1s" after changing "Recording format" to "H.264". • When the setting value of "Recording format" is changed to "H.264", the setting value of "Save logs" on the [Log] tab (☞ page 43) of the "Basic" page will automatically be changed. • When the setting value of "Recording format" is changed to "H.264", the setting value of "Save logs" on the [Log] tab (☞ page 43) of the "Basic" page will automatically be changed. • When "H.264" is selected for "Recording format", alarm images are saved in accordance with the set- tings of "Pre alarm" and "Post alarm (Recording) duration" on the [Alarm] tab of the "Alarm" page. • When "H.264" is selected for "Recording format", the name of the saved file will be given automati- cally. ■ Common [Remaining capacity notification] When the mail notification function or the Panasonic alarm protocol function is used to provide notification of the remaining capacity of the SD memory card, select a level to be notified at from the following. 50%/ 20%/ 10%/ 5%/ 2% Default: 50% Note: • Notification will be provided each time the remaining capacity of the SD memory card reached the values above. For example, notification will be provided each time the remaining capacity reaches 50%, 20%, 10%, 5% and 2% when "50%" is selected. Notification may not always be made at the very moment when the remaining capacity of the SD memory card has reached each value. [Save trigger] Select a trigger to save images on the SD memory card from the following. FTP error: Saves images when images have failed to transmit to the FTP server by the FTP periodic image transmission function. (Available only for JPEG images) Alarm input: Saves images at an alarm occurrence. Manual: Saves images manually. Schedule: Saves images in accordance with the set- tings for "Schedule" (☞ page 120). (Available only for H.264 images) Default: FTP error Note: • When "H.264" is selected for "Recording format", "FTP error" is unavailable. • Select "FTP error" when images are to be transmit- ted to the FTP server at an alarm occurrence. • When "JPEG" is selected for "Recording format", "Schedule" is unavailable. [Overwrite] Determine whether or not to overwrite when the remaining capacity of the SD memory card becomes insufficient. This setting is available only when "Manual" or "Schedule" is selected for "Save trigger". On: Overwrites when the remaining capacity of the SD memory card becomes insufficient. (The oldest image is the first to be overwritten.) Off: Stops saving images on the SD memory card when the SD memory card becomes full. Default: Off Note: The overwrite setting will be as follows according to the "Save trigger" setting. FTP error: Will not be overwritten. Alarm input: Will be overwritten. Manual, Schedule: Can be determined by selecting "On" or "Off" for "Overwrite".

This setting is available only when "JPEG" is selected for "Recording format" of the SD memory card. [File name] Enter the file name used for the image to be saved on the SD memory card. The file name will be as follows. File name: ["Entered file name" + "Time and date (year/ month/ day/ hour/ minute/ second)"] + "Serial num- ber" Available number of characters: 1 - 8 characters Note: • When "H.264" is selected for "Recording format", the name of the saved file will be given automati- cally. • When "FTP error" is selected for "Save trigger", the file name entered for "File name" on the [FTP img. trans.] tab of the "Network" page will be used for the file name of the image saved on the SD memory card. [Image saving interval/Number of images to be saved - Image saving interval] When "Alarm input" or "Manual" is selected for "Save trigger", select an interval (frame rate) of saving images on the SD memory card from the following. 0.1fps/ 0.2fps/ 0.33fps/ 0.5fps/ 1fps Default: 1fps [Image saving interval/Number of images to be saved - Number of images to be saved] Select a number of alarm images to be saved on the SD memory card from the following. 10pics/ 20pics/ 30pics/ 50pics/ 100pics/ 200pics/ 300pics/ 500pics/ 1000pics/ 2000pics/ 3000pics Default: 100pics Note: • When "H.264" is selected for "Recording format", Pre alarm and Post alarm can be set on "H.264 recording" of [Alarm] tab. • "Number of images to be saved" can be configured only when "Alarm input" is selected for "Save trig- ger". [Image capture size] When "Manual" is selected for "Save trigger" and "JPEG" is selected for "Recording format", select the image capture size of the images to be saved on the SD memory card from the following. When "4:3(VGA)" is selected for "Aspect ratio" QVGA/ VGA/ 1280x960 When "4:3(800x600)" is selected for "Aspect ratio" SW395 SC385 QVGA/ 800x600/ 1280x960 When "16:9" is selected for "Aspect ratio" 320x180/ 640x360/ 1280x720 Default: VGA Note: • When "FTP error" is selected for "Save trigger", images will be saved with the image capture size selected on the [FTP img. trans.] tab of the "Network" page. • When "H.264" is selected for "Recording format", select the image capture size for "H.264 recording" - "Image capture size" on the [SD memory card] tab. • When "Alarm input" is selected for "Save trigger", images will be saved with the image capture size selected on the [Alarm] tab of the "Alarm" page. ■ H.264 recording This setting is available only when "H.264" is selected for "Recording format" of the SD memory card. When the second [Set] button on the setup page is clicked, the settings for "H.264 recording" will be dis- played on the bottom of the tab. [Image capture size] Select the image capture size from the following. When "4:3(VGA)" is selected for "Aspect ratio" QVGA/ VGA SC384 QVGA/ VGA/ 1280x960 SW395 SC385 When "4:3(800x600)" is selected for "Aspect ratio" SW395 SC385 QVGA/ 800x600/ 1280x960 When "16:9" is selected for "Aspect ratio" 320x180/ 640x360 SC384 320x180/ 640x360/ 1280x720 SW395 SC385 Default: VGA [Recording priority] Select "Constant bit rate" or "Frame rate" for the H.264 recording mode. Constant bit rate: H.264 images will be recorded with the bit rate selected for "Max. bit rate".

frame rate selected for "Frame rate*". Default: Frame rate [Frame rate*] Select the frame rate for images to be recorded from the following. 1fps/ 3fps/ 5fps*/ 7.5fps*/ 10fps*/ 12 fps*(PAL model)/ 15fps*/ 20fps*/ 30fps* Default: 30fps* Note: • When "Frame rate" is selected for "Recording prior- ity", this setting is available. • "Frame rate*" is limited by "Max bit rate". For this reason, the frame rate may be lower than the speci- fied value when any value marked with an asterisk (*) is selected. [Max bit rate] Select the bit rate for images to be recorded from the following. 64kbps/ 128kbps/ 256kbps/ 384kbps/ 512kbps/ 768kbps/ 1024kbps/ 1536kbps/ 2048kbps/ 3072kbps/ 4096kbps Default: 1536kbps [Image quality] Select the quality for H.264 images to be recorded from the following. Low(Motion priority)/ Normal/ Fine(Image quality prior- ity) Default: Normal Note: • When "Constant bit rate" is selected for "Recording priority", this setting is available. [Refresh interval] Select an interval (I-frame interval; 0.2 - 1 second) to refresh the H.264 images to be recorded from the fol- lowing. 0.2s/ 0.25s/ 0.33s/ 0.5s/ 1s Default: 1s ■ SD memory card information [Remaining capacity] Total capacity and remaining capacity of the SD mem- ory card will be displayed. Depending on the status of the SD memory card, the size indications will differ as follows. Indication Description --------KB/--------KB No SD memory card is insert- ed. Failed to obtain available capacity due to error, etc. ********KB/********KB The SD card memory is unfor- matted, or locked, etc. Note: • When "Off" is selected for "Overwrite" and the avail- able size of the SD memory card has reached "0 KB", images will not be saved on the SD memory card. When the notification function is on, a notifica- tion mail will be sent to the registered addresses when the SD memory card becomes full. (☞ Pages 83 and 84) [Format] To format the SD memory card, click the [Execute] but- ton. Important: • Before formatting the SD memory card, it is neces- sary to select "Use" for "SD memory card" on the [SD memory card] tab of the "Basic" page (☞ page 33) and "Off" for "FTP periodic image transmission" on the [FTP img. trans.] tab of the "Network" page (☞ page 117). • Use the SD memory card after formatting it using the [SD memory card] tab. If using the SD memory card that has not been formatted on the [SD mem- ory card] tab, the following functions may not work correctly. • Save/obtain images that failed to transmit to the FTP server using the FTP periodic image trans- mission function • Save/obtain alarm images • Save/obtain images saved manually • Save/obtain images in accordance with the schedule settings • Save/obtain the alarm logs, the manual/schedule logs, the FTP error logs and the system logs

memory recording function of Panasonic's net- work disk recorder. • Play/download images on the SD memory card • When an SD memory card is formatted while another user is in operation, the operation will be canceled. • It is impossible to access the SD memory card dur- ing the process of formatting. • All data saved on the SD memory card will be deleted when the SD memory card is formatted. • Do not turn off the power of the camera during the process of formatting. • When the setting of "Recording format" has been changed, it is recommended to format the SD mem- ory card. • After formatting the SD memory card, available size may be smaller than the total size since the default directory is automatically created in the SD memory card. • Recommended SD memory card Manufactured by Panasonic (option) SDHC memory card: 4 GB, 8 GB, 16 GB, 32 GB SD memory card: 256 MB, 512 MB, 1 GB, 2 GB (except miniSD card and microSD card) • Use a SD memory card formatted compliant with the SD memory card standard at the default. ■ SD memory card images [Access img.] Images on the SD memory card can be obtained. Click the [Execute] button. Refer to page 38 for how to access images.

[SD memory card images] Click the [SD memory card] tab on the "Basic" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The following are descriptions of how to copy images saved on the SD memory card onto the PC. It is necessary in advance to select "Allow" for "FTP access to camera" on the [Network] tab of the "Network" page. (☞ Page 97) Important: • It may sometimes be impossible to operate when another user is accessing images on the SD memory card. In this case, retry later. • Depending on the settings of a proxy server or a firewall, images may not be obtained via a network. In this case, refer to the network administrator. Step 1 Click the [Execute] button of "Access img.". → The user authentication window will be displayed. Step 2 Click the [OK] button after entering the user name and the password of the camera administrator. → The folder in which images are to be saved will be displayed. Note: • When logging in the FTP server of the camera to access images, the SD memory card will be allo- cated to the drive B. Images are saved in different directories according to "Save trigger". Move to the directory corresponding to the desired images and copy them. Refer to page 141 for further information about the directory structure.

For JPEG images Important: • The numbers on the following table are just indications. They are not actual numbers of images that can be saved on the SD memory card. Numbers will differ according to photographic subject to the SD memory card. Image capture size: 1 280 x 960 Capacity of SD/ SDHC memory card 32 GB 16 GB 8 GB 4 GB 2 GB 1 GB 512 MB 256 MB Capacity of SD/ SDHC memory card Approx. 160 000 pics Approx. 80 000 pics Approx. 40 000 pics Approx. 20 000 pics Approx. 10 000 pics Approx. 5 000 pics Approx. 2 500 pics Approx. 1 250 pics Approx. 224 000 pics Approx. 112 000 pics Approx. 56 000 pics Approx. 28 000 pics Approx. 14 000 pics Approx. 7 000 pics Approx. 3 500 pics Approx. 1 750 pics Approx. 256 000 pics Approx. 128 000 pics Approx. 64 000 pics Approx. 32 000 pics Approx. 16 000 pics Approx. 8 000 pics Approx. 4 000 pics Approx. 2 000 pics Approx. 288 000 pics Approx. 144 000 pics Approx. 72 000 pics Approx. 36 000 pics Approx. 18 000 pics Approx. 9 000 pics Approx. 4 500 pics Approx. 2 250 pics Approx. 320 000 pics Approx. 160 000 pics Approx. 80 000 pics Approx. 40 000 pics Approx. 20 000 pics Approx. 10 000 pics Approx. 5 000 pics Approx. 2 500 pics 5(Normal) 6 7 8 9(Low) Image quality 32 GB 16 GB 8 GB 4 GB 2 GB 1 GB 512 MB 256 MB Approx. 64 000 pics Approx. 32 000 pics Approx. 16 000 pics Approx. 8 000 pics Approx. 4 000 pics Approx. 2 000 pics Approx. 1 000 pics Approx. 500 pics Approx. 80 000 pics Approx. 40 000 pics Approx. 20 000 pics Approx. 10 000 pics Approx. 5 000 pics Approx. 2 500 pics Approx. 1 250 pics Approx. 625 pics Approx. 96 000 pics Approx. 48 000 pics Approx. 24 000 pics Approx. 12 000 pics Approx. 6 000 pics Approx. 3 000 pics Approx. 1 500 pics Approx. 750 pics Approx. 112 000 pics Approx. 56 000 pics Approx. 28 000 pics Approx. 14 000 pics Approx. 7 000 pics Approx. 3 500 pics Approx. 1 750 pics Approx. 875 pics Approx. 128 000 pics Approx. 64 000 pics Approx. 32 000 pics Approx. 16 000 pics Approx. 8 000 pics Approx. 4 000 pics Approx. 2 000 pics Approx. 1 000 pics 0(Super fine) 1(Fine) 2 3 4 Image quality Image capture size: 1 280 x 720 Capacity of SD/ SDHC memory card 32 GB 16 GB 8 GB 4 GB 2 GB 1 GB 512 MB 256 MB Capacity of SD/ SDHC memory card Approx. 230 400 pics Approx. 115 200 pics Approx. 57 600 pics Approx. 28 800 pics Approx. 14 400 pics Approx. 7 200 pics Approx. 3 600 pics Approx. 1 800 pics Approx. 294 400 pics Approx. 147 200 pics Approx. 73 600 pics Approx. 36 800 pics Approx. 18 400 pics Approx. 9 200 pics Approx. 4 600 pics Approx. 2 300 pics Approx. 358 400 pics Approx. 179 200 pics Approx. 89 600 pics Approx. 44 800 pics Approx. 22 400 pics Approx. 11 200 pics Approx. 5 600 pics Approx. 2 800 pics Approx. 384 000 pics Approx. 192 000 pics Approx. 96 000 pics Approx. 48 000 pics Approx. 24 000 pics Approx. 12 000 pics Approx. 6 000 pics Approx.3 000 pics Approx. 409 600 pics Approx. 204 800 pics Approx. 102 400 pics Approx. 51 200 pics Approx. 25 600 pics Approx. 12 800 pics Approx. 6 400 pics Approx. 3 200 pics 5(Normal) 6 7 8 9(Low) Image quality 32 GB 16 GB 8 GB 4 GB 2 GB 1 GB 512 MB 256 MB Approx. 76 800 pics Approx. 38 400 pics Approx. 19 200 pics Approx. 9 600 pics Approx. 4 800 pics Approx. 2 400 pics Approx. 1 200 pics Approx. 600 pics Approx. 102 400 pics Approx. 51 200 pics Approx. 25 600 pics Approx. 12 800 pics Approx. 6 400 pics Approx. 3 200 pics Approx. 1 600 pics Approx. 800 pics Approx. 128 000 pics Approx. 64 000 pics Approx. 32 000 pics Approx. 16 000 pics Approx. 8 000 pics Approx. 4 000 pics Approx. 2 000 pics Approx. 1 000 pics Approx. 140 800 pics Approx. 70 400 pics Approx. 35 200 pics Approx. 17 600 pics Approx. 8 800 pics Approx. 4 400 pics Approx. 2 200 pics Approx. 1 100 pics Approx. 166 400 pics Approx. 83 200 pics Approx. 41 600 pics Approx. 20 800 pics Approx. 10 400 pics Approx. 5 200 pics Approx. 2 600 pics Approx. 1 300 pics 0(Super fine) 1(Fine) 2 3 4 Image quality

SW395 SC385 Capacity of SD/ SDHC memory card 32 GB 16 GB 8 GB 4 GB 2 GB 1 GB 512 MB 256 MB Capacity of SD/ SDHC memory card Approx. 320 000 pics Approx. 160 000 pics Approx. 80 000 pics Approx.40 000 pics Approx. 20 000 pics Approx. 10 000 pics Approx. 5 000 pics Approx. 2 500 pics Approx. 384 000 pics Approx. 192 000 pics Approx. 96 000 pics Approx. 48 000 pics Approx. 24 000 pics Approx. 12 000 pics Approx. 6 000 pics Approx. 3 000 pics Approx. 422 400 pics Approx. 211 200 pics Approx. 105 600 pics Approx. 52 800 pics Approx. 26 400 pics Approx. 13 200 pics Approx. 6 600 pics Approx. 3 300 pics Approx. 460 800 pics Approx. 230 400 pics Approx. 115 200 pics Approx. 57 600 pics Approx. 28 800 pics Approx. 14 400 pics Approx. 7 200 pics Approx. 3 600 pics Approx. 480 000 pics Approx. 240 000 pics Approx. 120 000 pics Approx. 60 000 pics Approx. 30 000 pics Approx. 15 000 pics Approx. 7 500 pics Approx. 3 750 pics 5(Normal) 6 7 8 9(Low) Image quality 32 GB 16 GB 8 GB 4 GB 2 GB 1 GB 512 MB 256 MB Approx. 102 400 pics Approx. 51 200 pics Approx. 25 600 pics Approx. 12 800 pics Approx. 6 400 pics Approx. 3 200 pics Approx. 1 600 pics Approx. 800 pics Approx. 160 000 pics Approx. 80 000 pics Approx. 40 000 pics Approx. 20 000 pics Approx. 10 000 pics Approx. 5 000 pics Approx. 2 500 pics Approx. 1 250 pics Approx. 192 000 pics Approx. 96 000 pics Approx. 48 000 pics Approx. 24 000 pics Approx. 12 000 pics Approx. 6 000 pics Approx. 3 000 pics Approx. 1 500 pics Approx. 243 200 pics Approx. 121 600 pics Approx. 60 800 pics Approx. 30 400 pics Approx. 15 200 pics Approx. 7 600 pics Approx. 3 800 pics Approx. 1 900 pics Approx. 281 600 pics Approx. 140 800 pics Approx. 70 400 pics Approx. 35 200 pics Approx. 17 600 pics Approx. 8 800 pics Approx. 4 400 pics Approx. 2 200 pics 0(Super fine) 1(Fine) 2 3 4 Image quality Image capture size: VGA Capacity of SD/ SDHC memory card 32 GB 16 GB 8 GB 4 GB 2 GB 1 GB 512 MB 256 MB Capacity of SD/ SDHC memory card Approx. 352 000 pics Approx. 176 000 pics Approx. 88 000 pics Approx. 44 000 pics Approx. 22 000 pics Approx. 11 000 pics Approx. 5 500 pics Approx. 2 750 pics Approx. 416 000 pics Approx. 208 000 pics Approx. 104 000 pics Approx. 52 000 pics Approx. 26 000 pics Approx. 13 000 pics Approx. 6 500 pics Approx. 3 250 pics Approx. 448 000 pics Approx. 224 000 pics Approx. 112 000 pics Approx. 56 000 pics Approx. 28 000 pics Approx. 14 000 pics Approx. 7 000 pics Approx. 3 500 pics Approx. 480 000 pics Approx. 240 000 pics Approx. 120 000 pics Approx. 60 000 pics Approx. 30 000 pics Approx. 15 000 pics Approx. 7 500 pics Approx. 3 750 pics Approx. 512 000 pics Approx. 256 000 pics Approx. 128 000 pics Approx. 64 000 pics Approx. 32 000 pics Approx. 16 000 pics Approx. 8 000 pics Approx. 4 000 pics 5(Normal) 6 7 8 9(Low) Image quality 32 GB 16 GB 8 GB 4 GB 2 GB 1 GB 512 MB 256 MB Approx. 160 000 pics Approx. 80 000 pics Approx. 40 000 pics Approx. 20 000 pics Approx. 10 000 pics Approx. 5 000 pics Approx. 2 500 pics Approx. 1 250 pics Approx. 224 000 pics Approx. 112 000 pics Approx. 56 000 pics Approx. 28 000 pics Approx. 14 000 pics Approx. 7 000 pics Approx. 3 500 pics Approx. 1 750 pics Approx. 256 000 pics Approx. 128 000 pics Approx. 64 000 pics Approx. 32 000 pics Approx. 16 000 pics Approx. 8 000 pics Approx. 4 000 pics Approx. 2 000 pics Approx. 288 000 pics Approx. 144 000 pics Approx. 72 000 pics Approx. 36 000 pics Approx. 18 000 pics Approx. 9 000 pics Approx. 4 500 pics Approx. 2 250 pics Approx. 320 000 pics Approx. 160 000 pics Approx. 80 000 pics Approx. 40 000 pics Approx. 20 000 pics Approx. 10 000 pics Approx. 5 000 pics Approx. 2 500 pics 0(Super fine) 1(Fine) 2 3 4 Image quality

Capacity of SD/ SDHC memory card 32 GB 16 GB 8 GB 4 GB 2 GB 1 GB 512 MB 256 MB Capacity of SD/ SDHC memory card Approx. 499 200 pics Approx. 249 600 pics Approx. 124 800 pics Approx. 62 400 pics Approx. 31 200 pics Approx. 15 600 pics Approx. 7 800 pics Approx. 3 900 pics Approx. 537 600 pics Approx. 268 800 pics Approx. 134 400 pics Approx. 67 200 pics Approx. 33 600 pics Approx. 16 800 pics Approx. 8 400 pics Approx. 4 200 pics Approx. 627 200 pics Approx. 313 600 pics Approx. 156 800 pics Approx. 78 400 pics Approx. 39 200 pics Approx. 19 600 pics Approx. 9 800 pics Approx. 4 900 pics Approx. 640 000 pics Approx. 320 000 pics Approx. 160 000 pics Approx. 80 000 pics Approx. 40 000 pics Approx. 20 000 pics Approx. 10 000 pics Approx. 5 000 pics Approx. 652 800 pics Approx. 326 400 pics Approx. 163 200 pics Approx. 81 600 pics Approx. 40 800 pics Approx. 20 400 pics Approx. 10 200 pics Approx. 5 100 pics 5(Normal) 6 7 8 9(Low) Image quality 32 GB 16 GB 8 GB 4 GB 2 GB 1 GB 512 MB 256 MB Approx. 192 000 pics Approx. 96 000 pics Approx. 48 000 pics Approx. 24 000 pics Approx. 12 000 pics Approx. 6 000 pics Approx. 3 000 pics Approx. 1 500 pics Approx. 281 600 pics Approx. 140 800 pics Approx. 70 400 pics Approx. 35 200 pics Approx. 17 600 pics Approx. 8 800 pics Approx. 4 400 pics Approx. 2 200 pics Approx. 332 800 pics Approx. 166 400 pics Approx. 83 200 pics Approx. 41 600 pics Approx. 20 800 pics Approx. 10 400 pics Approx. 5 200 pics Approx. 2 600 pics Approx. 358 400 pics Approx. 179 200 pics Approx. 89 600 pics Approx. 44 800 pics Approx. 22 400 pics Approx. 11 200 pics Approx. 5 600 pics Approx. 2 800 pics Approx. 409 600 pics Approx. 204 800 pics Approx. 102 400 pics Approx. 51 200 pics Approx. 25 600 pics Approx. 12 800 pics Approx. 6 400 pics Approx. 3 200 pics 0(Super fine) 1(Fine) 2 3 4 Image quality Image capture size: QVGA Capacity of SD/ SDHC memory card 32 GB 16 GB 8 GB 4 GB 2 GB 1 GB 512 MB 256 MB Capacity of SD/ SDHC memory card Approx. 512 000 pics Approx. 256 000 pics Approx. 128 000 pics Approx. 64 000 pics Approx. 32 000 pics Approx. 16 000 pics Approx. 8 000 pics Approx. 4 000 pics Approx. 576 000 pics Approx. 288 000 pics Approx. 144 000 pics Approx. 72 000 pics Approx. 36 000 pics Approx. 18 000 pics Approx. 9 000 pics Approx. 4 500 pics Approx. 608 000 pics Approx. 304 000 pics Approx. 152 000 pics Approx. 76 000 pics Approx. 38 000 pics Approx. 19 000 pics Approx. 9 500 pics Approx. 4 750 pics Approx. 640 000 pics Approx. 320 000 pics Approx. 160 000 pics Approx. 80 000 pics Approx. 40 000 pics Approx. 20 000 pics Approx. 10 000 pics Approx. 5 000 pics Approx. 672 000 pics Approx. 336 000 pics Approx. 168 000 pics Approx. 84 000 pics Approx. 42 000 pics Approx. 21 000 pics Approx. 10 500 pics Approx. 5 250 pics 5(Normal) 6 7 8 9(Low) Image quality 32 GB 16 GB 8 GB 4 GB 2 GB 1 GB 512 MB 256 MB Approx. 384 000 pics Approx. 192 000 pics Approx. 96 000 pics Approx. 48 000 pics Approx. 24 000 pics Approx. 12 000 pics Approx. 6 000 pics Approx. 3 000 pics Approx. 416 000 pics Approx. 208 000 pics Approx. 104 000 pics Approx. 52 000 pics Approx. 26 000 pics Approx. 13 000 pics Approx. 6 500 pics Approx. 3 250 pics Approx. 432 000 pics Approx. 216 000 pics Approx. 108 000 pics Approx. 54 000 pics Approx. 27 000 pics Approx. 13 500 pics Approx. 6 750 pics Approx. 3 375 pics Approx. 448 000 pics Approx. 224 000 pics Approx. 112 000 pics Approx. 56 000 pics Approx. 28 000 pics Approx. 14 000 pics Approx. 7 000 pics Approx. 3 500 pics Approx. 480 000 pics Approx. 240 000 pics Approx. 120 000 pics Approx. 60 000 pics Approx. 30 000 pics Approx. 15 000 pics Approx. 7 500 pics Approx. 3 750 pics 0(Super fine) 1(Fine) 2 3 4 Image quality

Approx. 288 000 pics Approx. 144 000 pics Approx. 72 000 pics Approx. 36 000 pics Approx. 18 000 pics Approx. 9 000 pics Approx. 4 500 pics Image capture size: 320 x 180 Capacity of SD/ SDHC memory card 32 GB 16 GB 8 GB 4 GB 2 GB 1 GB 512 MB 256 MB Capacity of SD/ SDHC memory card Approx. 729 600 pics Approx. 364 800 pics Approx. 182 400 pics Approx. 91 200 pics Approx. 45 600 pics Approx. 22 800 pics Approx. 11 400 pics Approx. 5 700 pics Approx. 755 200 pics Approx. 377 600 pics Approx. 188 800 pics Approx. 94 400 pics Approx. 47 200 pics Approx. 23 600 pics Approx. 11 800 pics Approx. 5 900 pics Approx. 793 600 pics Approx. 396 800 pics Approx. 198 400 pics Approx. 99 200 pics Approx. 49 600 pics Approx. 24 800 pics Approx. 12 400 pics Approx. 6 200 pics Approx. 844 800 pics Approx. 422 400 pics Approx. 211 200 pics Approx. 105 600 pics Approx. 52 800 pics Approx. 26 400 pics Approx. 13 200 pics Approx. 6 600 pics Approx. 857 600 pics Approx. 428 800 pics Approx. 214 400 pics Approx. 107 200 pics Approx. 53 600 pics Approx. 26 800 pics Approx. 13 400 pics Approx. 6 700 pics 5(Normal) 6 7 8 9(Low) Image quality 32 GB 16 GB 8 GB 4 GB 2 GB 1 GB 512 MB 256 MB Approx. 460 800 pics Approx. 230 400 pics Approx. 115 200 pics Approx. 57 600 pics Approx. 28 800 pics Approx. 14 400 pics Approx. 7 200 pics Approx. 3 600 pics Approx. 524 800 pics Approx. 262 400 pics Approx. 131 200 pics Approx. 65 600 pics Approx. 32 800 pics Approx. 16 400 pics Approx. 8 200 pics Approx. 4 100 pics Approx. 563 200 pics Approx. 281 600 pics Approx. 140 800 pics Approx. 70 400 pics Approx. 35 200 pics Approx. 17 600 pics Approx. 8 800 pics Approx. 4 400 pics Approx. 614 400 pics Approx. 307 200 pics Approx. 153 600 pics Approx. 76 800 pics Approx. 38 400 pics Approx. 19 200 pics Approx. 9 600 pics Approx. 4 800 pics 0(Super fine) 1(Fine) 2 3 4 Image quality

Click the [Log] tab on the "Basic" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The settings relating to the log list can be configured in this section. ■ Alarm Settings for the alarm log list can be performed. [Save logs] Select "On" or "Off" to determine whether to save the alarm logs. On: Alarm logs will be saved. Off: Alarm logs will not be saved. Default: On Note: • When "H.264" is selected for "Recording format", "On" or "Off" will automatically be selected for "Save logs" according to the setting of "Save trig- ger". • When "H.264" is selected for "Recording format" and when "Manual" or "Schedule" is selected for "Save trigger", alarm logs will not be saved. [Name of the destination directory for downloaded images] Enter the name of the destination directory to which images associated with the logs are to be downloaded. For example, enter "C:\alarm" to designate the folder "alarm" under drive C. Available number of characters: 3 - 128 characters Available characters: Alphanumeric characters, the slash (/), the backslash (\), the colon (:) and the underscore (_). ■ Manual/Schedule Configure the settings relating to manual saving or schedule saving of the log list. Select "On" or "Off" and designate the destination folder in the same manner as for "Alarm". Note: • When "H.264" is selected for "Recording format", "On" or "Off" will automatically be selected for "Save logs" according to the setting of "Save trig- ger". • Schedule saving is available only when "H.264" is selected for "Recording format". ■ FTP error Perform the settings for the FTP error log list. Select "On" or "Off" and designate the destination folder in the same manner as for "Alarm". Important: • When "Name w/o time&date" is selected for "File name" on the [FTP img. trans.] tab on the "Network" page, FTP error log and associated images will not be saved. To save them, select "Name w/ time&date". (☞ Page 117) Note: • When "H.264" is selected for "Recording format", "FTP error" is unavailable.

[Log] tab Off Use Alarm input Logs: Will not be saved. Images: Will be saved. When the remaining capacity of the SD memory card becomes insufficient, the older images will be overwritten by the newer images. * To display images on the SD memory card, it is nec- essary to copy them onto the PC first. (☞ Page 38) On Alarm: Save logs Not use Other than "Alarm input" – [SD memory card] tab SD memory card Use Not use – Save trigger Alarm input Other than "Alarm input" Logs: Up to 5 000 logs will be kept. When more than 5 000 event logs are filed, the older event logs will be over- written by the newer event logs. Images: Will be saved. When the remaining capacity of the SD memory card becomes insufficient, the older images will be overwritten by the newer images. Logs: Up to 1 000 logs will be kept. When more than 1 000 logs are filed, the older logs will be overwritten by the newer logs. In this case, the oldest log is the first to be overwritten. When the power of the camera is turned off, logs will be deleted. Images: Will not be saved. Logs: Will not be saved. Images: Will not be saved. Logs: Will not be saved. Images: Will not be saved. Logs: Up to 5 000 logs will be kept. When more than 5 000 logs are filed, the older logs will be overwritten by the newer logs. In this case, the oldest log is the first to be overwritten. Images: Will not be saved. Logs and associated images

"Manual/Schedule" [Log] tab On Logs and associated images Manual/ Schedule: Save logs Not use Not use – – – – Use Other than "Manual/ Schedule" – Logs: Will not be saved. Images: Will not be saved. Off Manual/ Schedule On Off [SD memory card] tab SD memory card Use Other than "Manual/ Schedule" – Save trigger Overwrite Manual/ Schedule On Off Logs: Up to 5 000 logs will be kept. When more than 5 000 logs are filed, the older logs will be overwritten by the newer logs. In this case, the oldest log is the first to be overwritten. Images: Will be saved. When the remaining capacity of the SD memory card becomes insufficient, the older images will be overwritten by the newer images. Logs: Will not be saved. Images: Will not be saved. Logs: Will not be saved. Images: Will not be saved. Logs: Will not be saved. Images: Will not be saved. Logs: Will not be saved. Images: Will be saved. When the remaining capacity of the SD memory card becomes insufficient, the older images will be overwritten by the newer images. * To display images on the SD memory card, it is nec- essary to copy them onto the PC first. (☞ Page 38) Logs: Will not be saved. Images: Will be saved. When available capacity of the SD mem- ory card ran out, saving of images will become impossi- ble. * To display images on the SD memory card, it is nec- essary to copy them onto the PC first. (☞ Page 38) Logs: Up to 5 000 logs will be kept. When more than 5 000 logs are filed, no log will be filed newly anymore. Even when available capacity of the SD memory card ran out and it is not enough to save images, logs will be kept on being filed until it reaches 5 000 logs. Images: Will be saved. When available capacity of the SD mem- ory card ran out, saving of images will become impossi- ble. Even when available capacity of the SD memory card is enough, images associated with logs will be kept on being saved until number of filed logs reaches 5 000.

error" Logs and associated images [Log] tab Off Use Not use Other than "FTP error" – FTP error Not use – Other than "FTP error" Logs: Will not be saved. Images: Will not be saved. Logs: Will not be saved. Images: Will be saved. When available capacity of the SD mem- ory card ran out, saving of images will become impossi- ble. * To display images on the SD memory card, it is nec- essary to copy them onto the PC first. (☞ Page 38) Logs: Will not be saved. Images: Will not be saved. Logs: Will not be saved. Images: Will not be saved. Logs: Will not be saved. Images: Will not be saved. On FTP error: Save logs [SD memory card] tab SD memory card Use Save trigger FTP error Logs: Up to 5 000 logs will be kept. When more than 5 000 logs are filed, no log will be filed newly anymore. Even when available capacity of the SD memory card ran out and it is not enough to save images, logs will be kept on being filed until it reaches 5 000 logs. Images: Will be saved. When available capacity of the SD mem- ory card ran out, saving of images will become impossi- ble.

audio [Image/Audio] The settings relating to JPEG, H.264 and MPEG-4 images such as the settings of image quality, audio, etc. can be configured on this page. The "Image/Audio" page has 4 tabs; the [JPEG/H.264] tab (or [JPEG/MPEG-4] tab), the [Cam. Function] tab, the [Image/Position] tab and the [Audio] tab. Configure the settings relating to the aspect ratio [JPEG/H.264] Click the [JPEG/H.264] tab on the "Image/Audio" page. (☞ Pages 26 and 27: How to display/operate the setup menu) [Aspect ratio] Select the aspect ratio. It is impossible to activate "VGA" and "800x600" simultaneously. Select "VGA" or "800x600" when the aspect ratio is 4:3. • 4:3 (VGA) • 4:3 (800 x 600) SW395 SC385 • 16:9 Default: 4:3 (VGA) Note: • When "4:3 (800x600)"* or "16:9" is selected, MPEG-4 transmission is unavailable. * SW395 SC385 • i-PRO Series does not support aspect ratio of "16:9". (As of October, 2010) • When selecting "4:3 (800x600)"* or "16:9" for "Aspect ratio", "H.264" is automatically set for "Video encoding format". * SW395 SC385 • Image adjustment functions are activated for the angle of view in the aspect ratio of 4:3 even while "16:9" is being selected for "Aspect ratio". When setting the mask area for the back light compensa- tion (BLC) function, it is recommended to configure the setting after selecting "4:3" for "Aspect ratio". ■ JPEG Configure the settings such as "Refresh interval (JPEG)*", "Image capture size" and "Image quality" on this section. Refer to page 49 and 53 for further infor- mation about the settings relating to H.264 (or MPEG-4) images. "Live" page (Initial display) Configure the settings relating to the JPEG images dis- played on the "Live" page. Configure the settings relating to JPEG images [JPEG/H.264] (or [JPEG/MPEG-4]) Click the [JPEG/H.264] tab (or [JPEG/MPEG-4] tab) on the "Image/Audio" page. (☞ Pages 26 and 27: How to dis- play/operate the setup menu)

Select an interval to refresh the displayed JPEG image from the following. SW395 SC385 0.1 fps/ 0.2 fps / 0.33 fps / 0.5 fps / 1 fps / 2 fps / 3 fps / 5 fps / 6 fps / 10 fps / 12 fps *(PAL only)/ 15 fps * /30 fps * Default: 10 fps SC384 0.1 fps / 0.2 fps / 0.33 fps / 0.5 fps / 1 fps / 2 fps / 3 fps / 5 fps / 6 fps */ 10 fps */ 12 fps *(PAL only)/ 15 fps * / 30 fps * Default: 5 fps Note: • When "On" is selected for "H.264 transmission" (or "MPEG-4 transmission"), the refresh interval may be longer than the set value when any value with an asterisk (*) on the right is selected. [Image capture size] Select the image capture size to display the JPEG image on the "Live" page for the first time. When "4:3(VGA)" is selected for "Aspect ratio" QVGA/ VGA/ 1280x960 When "4:3(800x600)" is selected for "Aspect ratio" SW395 SC385 QVGA/ 800x600/ 1280x960 When "16:9" is selected for "Aspect ratio" 320x180/ 640x360/ 1280x720 Default: 1280x960 [Image quality] Select the capture size of the JPEG image displayed initially on the "Live" page. Default: Quality1 [Image quality setting] Select two types of image quality of JPEG images for each image capture size. 0 Super fine/ 1 Fine/ 2/ 3/ 4/ 5 Normal/ 6/ 7/ 8/ 9 Low Default: Quality1: 5 Normal Quality2: 8 The setting for "Quality1" is activated for FTP periodic image transmission, files attached to alarm mails and SD memory recording.

Click the [JPEG/H.24] tab on the "Image/Audio" page. (☞ Pages 26 and 27: How to display/operate the setup menu) [JPEG/H.264] tab will be displayed when "H.264" is selected for "Video encoding format". Configure the settings relating to H.264 image such as "Max bit rate (per client)", "Image capture size", "Image quality", etc. in this section. Refer to page 53 and 47 for the settings relating to MPEG-4 images and JPEG images respectively. [Video encoding format] Select "H.264" for the video encoding format. H.264: H.264 will be set for the video encoding format. The subsequent setting items will be for H.264. The tab name will be changed to [JPEG/H.264]. MPEG-4: MPEG-4 will be set for the video encoding format. The subsequent setting items will be for MPEG-4. (☞ Page 53) The tab name will be changed to [JPEG/MPEG-4]. Default: H.264 ■H.264 (1) · H.264 (2) [H.264 transmission] Select "On" or "Off" to determine whether or not to transmit H.264 images. On: Transmits H.264 images. Off: Does not transmit H.264 images. Default: On Note: • When "On" is selected for "H.264 transmission" in "H.264(1)" or "H.264(2)", displaying of H.264 images or JPEG images on the "Live" page will become available. • When "On" is selected for "H.264 transmission" in "H.264(1)" and "H.264(2)", H.264 images are view- able using other devices with each setting. • When "On" is selected for "H.264 transmission" in "H.264(1)" or "H.264(2)", the transmission interval of JPEG images may sometimes become longer. • When "H.264" is selected for "Recording format" , it is impossible to transmit H.264 images with the set- tings for "H.264(2)". In this case, the settings for "H.264(2)" are invalidated. [Internet mode (over HTTP)] Select "On" when transmitting H.264 images via the Internet. It is possible to transmit H.264 images without changing the broadband router settings configured for JPEG image transmission. On: H.264 images and audio will be transmitted using the HTTP port. Refer to page 94 for further informa- tion about the HTTP port number settings. Off: H.264 images and audio will be transmitted using the UDP port. Default: Off Note: • When "On" is selected, only "Unicast port (AUTO)" will be available for "Transmission type". • When "On" is selected, it may take time to start dis- playing H.264 images.

displayed depending on the number of the concur- rent access user and audio data availability, etc. • When "On" is selected, only IPv4 access is avail- able. [Image capture size] Select the image capture size from the following. When "4:3(VGA)" is selected for "Aspect ratio" H.264(1): QVGA/ VGA/ 1280x960 H.264(2): QVGA/ VGA When "4:3(800x600)" is selected for "Aspect ratio" SW395 SC385 H.264(1): QVGA/ 800x600/ 1280x960 H.264(2): QVGA/ 800x600 When "16:9" is selected for "Aspect ratio" H.264(1): 320x180/ 640x360/ 1280x720 H.264(2): 320x180/ 640x360 Default: H.264(1): 1280x960 H.264(2): VGA [Transmission priority] Select a transmission priority for H.264 images from the following. Constant bit rate: H.264 images will be transmitted with the bit rate selected for "Max bit rate (per cli- ent) *". Frame rate: H.264 images will be transmitted with the frame rate selected for "Frame rate*". Best effort: In accordance with the network bandwidth, H.264 images will be transmitted with the bit rate varying between the maximum and minimum bit rates that are set for "Max bit rate (per client)*". Default: Frame rate Note: • When "Frame rate" is selected for "Transmission priority", number of users who can access the cam- era may be limited more (may become less than 10). [Frame rate*] Select a frame rate for H.264 images from the following. 1fps/ 3fps/ 5fps*/ 7.5fps*/ 10fps*/ 12 fps* (PAL model)/ 15fps*/ 20fps*/ 30fps* Default: 30fps* Note: • When "Frame rate" is selected for "Transmission priority", this setting is available. • "Frame rate*" is limited by "Max bit rate". For this reason, the frame rate may be lower than the speci- fied value when any value marked with an asterisk (*) is selected. [Max bit rate (per client)*] Select a H.264 bit rate per a client from the following. When "Best effort" is selected for "Transmission prior- ity", set the maximum and minimum bit rates. 64kbps/ 128 kbps*/ 256kbps*/ 384kbps*/ 512kbps*/ 768kbps*/ 1024kbps*/ 1536kbps*/ 2048kbps*/ 3072kbps*/ 4096kbps */ 8192kbps*/ Unlimited* Default: H.264(1): 4096kbps* H.264(2): 1536kbps* * "8192kbps*" is available only when the image cap- ture size is "1280x960" or "1280x720". * "128 kbps*" is available only when the image cap- ture size is "QVGA", "VGA", "800x600"*1 or "320x180", "640x360". *1 SW395 SC385 * "64kbps" is available only when the image capture size is "QVGA", "VGA" or "320x180", "640x360". * "Unlimited*" is available only when "Frame rate" is selected for "Transmission priority". Note: • The H.264 bit rate is limited by "Bandwidth control(bit rate)" on the [Network] tab of "Network" page (☞ page 97). For this reason, the bit rate may be lower than the value when any value with an asterisk (*) on the right is selected. • When "8192 kbps*" or "Unlimited*" is selected, the number of users who can access H.264 images will be limited to "1". (Only a single user can access H.264 images.) • It is impossible to select "Unlimited*" for both "H.264(1)" and "H.264(2)". [Image quality] Select the image quality of H.264 images from the fol- lowing. Low(Motion priority)/ Normal/ Fine(Image quality prior- ity) Default: Normal

for "Transmission priority", this setting is available. [Refresh interval] Select an interval (I-frame interval; 0.2 - 5 seconds) to refresh the displayed H.264 images. If using under a network environment with frequent error occurrences, shorten the refresh interval for H.264 to diminish image distortions. However, the refresh interval may be longer than the set value. 0.2s/ 0.25s/ 0.33s/ 0.5s/ 1s/ 2s/ 3s/ 4s/ 5s Default: 1s [Transmission type] Select the transmission type of H.264 images from the following. Unicast port (AUTO): Up to 14 users can access a sin- gle camera concurrently. "Unicast port1(Image)" and "Unicast port2(Audio)" will automatically be selected when transmitting images and audio from the cam- era. When it is unnecessary to fix the port number for H.264 image transmission such as when using in a particular LAN environment, it is recommended to select "Unicast port (AUTO)". Unicast port (MANUAL): Up to 14 users can access a single camera concurrently. It is necessary to select "Unicast port1(Image)" and "Unicast port2(Audio)" manually to transmit images and audio from the camera. It is possible to fix the port number of the router used for H.264 image transmission via the Internet by setting "Unicast port (MANUAL)" (☞ page 98). Refer to the operating instructions of the router in use. Multicast: Unlimited number of users can access a sin- gle camera concurrently. Complete the entry field of "Multicast address", "Multicast port" and "Multicast TTL/HOPLimit" when transmitting H.264 images with multicast. Refer to page 7 for further information about the maximum concurrent access number. Default: Unicast port (AUTO) [Unicast port1(Image)]*1 Enter the unicast port number (used to transmit images from the camera). Available port number: 1024 - 50000 (Only even num- bers are available.) Default: H.264(1): 32004 H.264(2): 32014 [Unicast port2(Audio)]*1 Enter the unicast port number (used to transmit audio from the camera). Available port number: 1024 - 50000 (Only even num- bers are available.) Default: H.264(1): 33004 H.264(2): 33014 [Multicast address]*2 Enter the multicast IP address. Images and audio will be transmitted to the designated IP address. Available IPv4 address: 224.0.0.0 - 239.255.255.255 Available IPv6 address: Multicast address starting with "FF" Default: H.264(1): 239.192.0.20 H.264(2): 239.192.0.21 Note: • Enter a multicast IP address after checking available multicast address. [Multicast port]*2 Enter the multicast port number (used to transmit images from the camera). Available port number: 1024 - 50000 (Only even num- bers are available.) Default: 37004 Note: • When audio is transmitted from the unit, the port number to be used will be the multicast port num- ber plus "1000". [Multicast TTL/HOPLimit]*2 Enter a value for "Multicast TTL/HOPLimit". Available value: 1-254 Default: 16

the transmitted image sometimes may not be dis- played depending on the settings of a proxy server or a firewall. In this case, refer to the network administrator. • When two or more network interface cards are installed on the PC in use, the network interface card(s) not used for receiving images should be invalidated when displaying images using the multi- cast port. *1 It is necessary to designate the unicast port number when "Unicast port (MANUAL)" is selected for "Transmission type". *2 It is necessary to designate the multicast IP address when "Multicast" is selected for "Transmission type".

[JPEG/MPEG-4] Click the [JPEG/MPEG-4] tab on the "Image/Audio" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The [JPEG/MPEG-4] tab will be displayed when "MPEG-4" is selected for "Video encoding format". (☞ Page 49) Configure the settings relating to MPEG-4 image such as "Max bit rate (per client)*", "Image capture size", "Image quality", etc. in this section. Refer to page 47 and 49 for the settings relating to JPEG images and H.264 images respectively. [Video encoding format] Select "MPEG-4" for the video encoding format. ■ MPEG-4 (1) · MPEG-4 (2) [MPEG-4 transmission] Select "On" or "Off" to determine whether or not to transmit MPEG-4 images. On: Transmits MPEG-4 images. Off: Does not transmit MPEG-4 images. Default: On Important: • When "4:3(800x600)"* or "16:9" is selected for "Aspect ratio", MPEG-4 transmission is unavailable. * SW395 SC385 • When "H.264" is selected for "Recording format", MPEG-4 transmission is unavailable. Note: • When "On" is selected for "MPEG-4 transmission" in "MPEG-4(1)" or "MPEG-4(2)", displaying of MPEG-4 images or JPEG images on the "Live" page will be available. • When "On" is selected for "MPEG-4 transmission" in "MPEG-4(1)" and "MPEG-4(2)", MPEG-4 images are viewable using other devices with each setting. • When "On" is selected for "MPEG-4 transmission" in "MPEG-4(1)" or "MPEG-4(2)", the transmission interval of JPEG images may be longer. [Internet mode (over HTTP)] Select "On" when transmitting MPEG-4 images via the Internet. It is possible to transmit MPEG-4 images with- out changing the broadband router settings configured for JPEG image transmission. On: MPEG-4 images and audio will be transmitted using the HTTP port. Refer to page 94 for further information about the HTTP port number settings. Off: MPEG-4 images and audio will be transmitted using the UDP port. Default: Off

will be available for "Transmission type". • When "On" is selected, it may take seconds to start displaying MPEG-4 images. • When "On" is selected, MPEG-4 images may not be displayed depending on the number of the concur- rent access users and audio data availability, etc. • When "On" is selected, only IPv4 access is avail- able. [Image capture size] Select "QVGA" or "VGA" for the image capture size of MPEG-4 images. Default: MPEG-4(1): VGA MPEG-4(2): VGA [Transmission priority] Select a transmission priority for MPEG-4 images from the following. Constant bit rate: MPEG-4 images will be transmitted with the bit rate selected for "Max bit rate (per cli- ent)*". Frame rate: MPEG-4 images will be transmitted with the frame rate selected for "Frame rate*". Best effort: In accordance with the network bandwidth, MPEG-4 images will be transmitted with the bit rate varying between the maximum and minimum bit rates that are set for "Max bit rate (per client)*". Default: Frame rate Note: • When "Frame rate" is set for "Transmission priority", number of users who can access the camera may be limited more (may become less than 10). [Frame rate*] Select a frame rate for MPEG-4 images from the follow- ing. 1fps/ 3fps/ 5fps*/ 7.5fps*/ 10fps*/ 12 fps*(PAL model)/ 15fps*/ 20fps*/ 30fps* Default: 30fps* Note: • When "Frame rate" is selected for "Transmission priority", this setting is available. • "Frame rate*" is limited by "Max bit rate (per cli- ent)*". For this reason, the frame rate may be lower than the specified value when any value marked with an asterisk (*) is selected. [Max bit rate (per client)*] Select a MPEG-4 bit rate per a client from the following. When "Best effort" is selected for "Transmission prior- ity", set the maximum and minimum bit rates. 64kbps/ 128kbps*/ 256kbps*/ 384kbps*/ 512kbps*/ 768kbps*/ 1024kbps*/ 1536kbps*/ 2048kbps*/ 3072kbps*/ 4096kbps*/ Unlimited* Default: MPEG-4(1): 2048kbps* MPEG-4(2): 2048kbps* * "Unlimited*" is available only when "Frame rate" is selected for "Transmission priority". Note: • The MPEG-4 bit rate is limited by "Bandwidth control(bit rate)" on the [Network] tab of "Network" page (☞ page 97). For this reason, the bit rate may be lower than the value when any value with an asterisk (*) on the right is selected. • When "Unlimited*" is selected, the number of users who can access MPEG-4 images will be limited to "1". (Only a single user can access MPEG-4images.) • It is impossible to select "Unlimited*" for both "MPEG-4(1)" and "MPEG-4(2)". [Image quality] Select the image quality of MPEG-4 images from the following. Low(Motion priority)/ Normal/ Fine(Image quality prior- ity) Default: Normal Note: • When "Constant bit rate" or "Best effort" is selected for "Transmission priority", this setting is available.

refresh the displayed MPEG-4 images. If using under a network environment with frequent error occurrences, shorten the refresh interval for MPEG-4 to diminish image distortions. However, the refresh interval may be longer than the set value. 0.2s/ 0.25s/ 0.33s/ 0.5s/ 1s/ 2s/ 3s/ 4s/ 5s Default: 1s [Transmission type] Select the transmission type of MPEG-4 images from the following. Unicast port (AUTO): Up to 14 users can access a sin- gle camera concurrently. "Unicast port1(Image)" and "Unicast port2 (Audio)" will automatically be selected when transmitting images and audio from the camera. When it is unnecessary to fix the port number for MPEG-4 image transmission such as when using in a particular LAN environment, it is recommended to select "Unicast port (AUTO)". Unicast port (MANUAL): Up to 14 users can access a single camera concurrently. It is necessary to select "Unicast port1 (Image)" and "Unicast port2 (Audio)" manually to transmit images and audio from the camera. It is possible to fix the port number of the router used for MPEG-4 image transmission via the Internet by setting "Unicast port (MANUAL)" (☞ page 98). Refer to the operating instructions of the router in use. Multicast: Unlimited number of users can access a sin- gle camera concurrently. Complete the entry field of "Multicast address", "Multicast port" and "Multicast TTL/HOPLimit" when transmitting MPEG-4 images with multicast. * Refer to page 7 for further information about the maximum concurrent access number. Default: Unicast port (AUTO) [Unicast port1(Image)]*1 Enter the unicast port number (used to transmit images from the camera). Available port number: 1024-50000 (Only even num- bers are available.) Default: MPEG-4(1): 32004 MPEG-4(2): 32014 [Unicast port2(Audio)]*1 Enter the unicast port number (used to transmit audio from the camera). Available port number: 1024-50000 (Only even num- bers are available.) Default: MPEG-4(1): 33004 MPEG-4(2): 33014 [Multicast address]*2 Enter the multicast IP address. Images and audio will be transmitted to the designated IP address. Available IPv4 address: 224.0.0.0 - 239.255.255.255 Available IPv6 address: Multicast address starting with "FF" Default: MPEG-4(1): 239.192.0.20 MPEG-4(2): 239.192.0.21 Note: • Enter a multicast IP address after checking available multicast address. [Multicast port]*2 Enter the multicast port number (used to transmit images from the camera). Available port number: 1024 - 50000 (Only even num- bers are available.) Default: 37004 Note: • When audio is transmitted from the camera, the port number to be used will be the multicast port num- ber plus "1000". [Multicast TTL/HOPLimit]*2 Enter the multicast TTL/HOPLimit value. Available value: 1 - 254 Default: 16 Important: • When transmitting an MPEG-4 image via a network, the transmitted image sometimes may not be dis- played depending on the settings of a proxy server or a firewall. In this case, refer to the network administrator. • When two or more network interface cards are installed on the PC in use, the network interface card(s) not used for receiving images should be invalidated when displaying images using the multi- cast port.

when "Unicast port (MANUAL)" is selected for "Transmission type". *2 It is necessary to designate the multicast IP address when "Multicast" is selected for "Transmission type". Configure the settings relating to the camera operations [Cam. Function] Click the [Cam. Function] tab on the "Image/Audio" page. (☞ Pages 26 and 27: How to display/operate the setup menu) Configure the settings relating to camera operations. [Home position] A preset position (☞ page 67) can be set as the home position. When a preset position is set as the home position, "H" will be displayed next to the preset position number. Default: Off Note: • To move the camera to the home position when the power of the camera is turned on, select "Home position" for "Self return". [Self return] When the time set for "Self return time" has passed after manual operations of the camera, the camera will automatically be in the selected mode. Off: Self return is not performed. Home position: When the set time has passed, the camera will move to the home position automati- cally. Auto track SW395 SC385 : When the set time has passed, the camera will move to the home position and will start the auto track function. The camera will repeat this action (moving to the home position and starting the auto track function) afterward. Auto pan: When the set time has passed, the camera will start the auto pan function. Preset sequence: When the set time has passed, the camera will start the sequence display. Default: Off Note: • This function is also useful to automatically set the camera in a specific mode when the power of the camera is turned on. • The self return function works even when the setup menu is displayed. [Self return time] Select a waiting time (amount of time until the camera starts the selected operation after the end of the man- ual operations) from the following. 10s/ 20s/ 30s/ 1min/ 2min/ 3min/ 5min/ 10min/ 20min/ 30min/ 60min Default: 1min [Image hold] Select "On" or "Off" to determine whether or not to hold the still image on the screen (that is displayed at the last moment before the camera started to move to a preset position) until the camera has moved to the pre- set position.

camera has moved to the preset position. Off: Images from the camera will be displayed even when the camera is moving to the preset position. Default: Off [Upside-down] SW395 SC385 Select "On (desktop)" or "Off (ceiling)" to determine how the camera is to be installed. On (desktop): Select this when the camera is to be installed with the dome side up. Off (ceiling): Select this when the camera is to be installed with the dome side down. Default: Off (ceiling) [Extra optical zoom] Select the extra optical zoom setting from the following. On (Max X36): Images can be zoomed in on with the optical zoom (1x - 18x) and the extra optical zoom (higher zoom factors, up to 36x). Off (Max X18): Does not use the extra optical zoom. Default: On (Max X36) About extra optical zoom Among approx. 1.3 megapixel image capture area of the MOS image sensor, the central part of approx. 0.31 megapixels is extracted for shooting. That enables the shooting with a higher zooming effect. When the image capture size under "VGA" is applied, the zoom factor can be adjusted up to 36x. [Digital zoom] Select the digital zoom setting from the following. On (Max X288) SC384 : Images can be zoomed in on with the optical zoom (1x - 18x) , extra optical zoom (up to 36x) and the electronic zoom (higher zoom factors, up to 288x). On (Max X432) SW395 SC385 : Images can be zoomed in on with the optical zoom (1x - 18x), extra optical zoom (up to 36x) and the electronic zoom (higher zoom factors, up to 432x). Off: Does not use the digital zoom. Default: Off Note: • When "On (Max X288)" SC384 or "On (Max X432)" SW395 SC385 is selected, digital zooming will stop when the zoom factor has reached 36x. • When the zoom factor is 36x or more, the setting of the preset positions will become unavailable. [Pan·Tilt degree/Zoom ratio display] Select "On" or "Off" to determine whether or not to dis- play the current panning/tilting degree and the zoom factor on images when the camera is being operated manually. On: Displays the current panning/tilting degree and the zoom factor. Off: Does not display the current panning/tilting degree and the zoom factor. Default: On Note: • When "On" is selected, the panning/tilting degree and the zoom factor will be displayed at the position selected for "OSD Position" on the [Basic] tab of the "Basic setup" page. (☞ Page 31) [Tilt Angle] Select the maximum degree for tilting from the follow- ing. (Level = 0°) 10°/ 5°/ 3°/ 0°/ –3°/ –5°/ –10°/ –15°/ –20°/ –25°/ –30° Default: 0° Note: • When using an inner cover (WV-Q157 or an acces- sory of optional mount bracket), upper side of images will be hidden (become black) when the tilt angle of the camera is almost level.　(When "–5°" is selected for "Tilt Angle" on the setup menu, upper half of images will be hidden.) In this case, images will also be washed out depending on the object when "On" is selected for "AGC" on the setup menu (☞ page 60). SC384 SC385 • If "−20°", "−25°" or "−30°" is selected, the area hid- den by the camera housing may increase when the tilt angle of the camera is almost level. SW395 [Pan/tilt-flip] Select the pan/tilt-flip setting from the following. On: When the camera reaches the panning or tilting end during manual operation, the camera pans or tilts at high speed to the reverse direction. In this way, it is possible to control the camera without having to stop panning/tilting and displaying images in proper orientation. Off: Pan/tilt-flip does not work. Default: On

tions [Image/Position] Click the [Image/Position] tab on the "Image/Audio" page. (☞ Pages 26 and 27: How to display/operate the setup menu) When the [Setup>>] button of each setting item is clicked, the detailed settings menu will be displayed in a newly opened window. The detailed settings can be configured while monitoring images displayed on the [Image/Position] tab. The following are descriptions of how to configure the settings relating to image quality, preset positions, auto pan function, privacy zone, etc. [Image adjust] Click the [Setup>>] button to display the setup menu that can configure the settings relating to image quality. The setup menu will be displayed in a newly opened window. (☞ Page 59 ) SW395 SC385 (☞ Page 63 ) SC384 [Preset position] Click the [Setup>>] button to display the setup menu that can configure the settings relating to the preset positions. The setup menu will be displayed in a newly opened window. (☞ Page 67) [Auto pan] Click the [Setup>>] button to display the setup menu that can configure the settings relating to the auto pan function. The setup menu will be displayed in a newly opened window. (☞ Page 70) [Privacy zone] Click the [Setup>>] button to display the setup menu that can configure the settings relating to the privacy zone. The setup menu will be displayed in a newly opened window. (☞ Page 71) Note: • The pan/tilt-flip function cannot be activated by clicking live images. • When the zoom ratio is adjusted to the "TELE" side, images will be partially hidden even if the pan/tilt- flip function is activated.

menu) SW395 SC385 Click the [Setup >>] button of "Image adjust" on the [Image/Position] tab of the "Image/Audio" page. (☞ Page 58) The settings relating to image quality can be configured with the setup menu displayed in a newly displayed win- dow. When the values are changed, the changed values will be applied to the currently displayed image on the [Image/Position] tab. [Super Dynamic(SD)] Select "On" or "Off" to determine whether or not to activate the super dynamic function. Refer to the description "Super Dynamic function" about the super dynamic function. On: The super dynamic function will work. Off: The super dynamic function will not work. Default: Off Note: • When the following are observed depending on the light condition, select "Off" for "Super Dynamic(SD)". • When flickering appears or the color changes on the screen • When noise appears in the brighter area on the screen • When "Outdoor scene" or "Indoor scene" is selected for "Light control mode", this setting is available. Super Dynamic function When there is wide variation between the illumina- tion of light and dark areas of the location being monitored, the camera adjusts the lens iris in accor- dance with the brighter areas. This causes loss of detail in darker areas. Conversely, adjusting the lens brightness for the darker areas causes the brighter areas to become washed out. Super Dynamic digitally combines an image that is set up for a clear view of the brighter areas with an image that is set up for a clear view of the darker areas, creating a final image that preserves overall detail. Subject in the dark area is hard to notice... Subject in the bright area is washed out... Creates a clearer image by digitally combining images [Face SD] Select "On" or "Off" to determine whether or not to interact with the Super Dynamic function. On: The interactive control with face detection will work. Off: The interactive control with face detection will not work. Default: Off Note: • When "Off" is selected for "Super Dynamic(SD)", the interactive control with face detection is deacti- vated.

Select "On" or "Off" to determine whether or not to activate the darkness compensation function. The dark- ness compensation function can make darker parts of images brighter by digital image processing. On: Activates the darkness compensation function. Off: Deactivates the darkness compensation function. Default: Off Important: • When "On" is selected for "Adaptive black stretch", noise in the darker parts may be increased, and parts around borders between the darker parts and the brighter parts may become darker/brighter than the other darker/brighter parts. [Back light compensation (BLC)] Select "On" or "Off" to determine whether or not to activate the back light compensation (BLC) function. When "On" is selected for "Super Dynamic(SD)", this setting is unavailable. The back light compensation function can compensate back light by setting mask areas on brighter parts of images brighter. On: Mask areas will be set automatically. Off: Mask areas will not be set automatically. It is nec- essary to set them manually. Default: Off [Mask area] When "Off" is selected for "Super Dynamic(SD)" and "Back light compensation(BLC)", it is possible to com- pensate for backlight by masking brighter areas. Refer to page 66 for information on how to set the mask area. [Light control mode] Select the light control mode from the following. Outdoor scene: Depending on the brightness level (illuminance), the iris will automatically be controlled together with the shutter speed adjustment to con- trol light. When shooting a bright subject such as outdoor, etc., select this parameter. Be aware that flicker may occur when a subject is under fluores- cent lighting. Indoor scene (50 Hz) Indoor scene (60 Hz): The shutter speed will automati- cally be adjusted to prevent flicker caused by fluo- rescent light. Select 50 Hz or 60 Hz corresponding to the location where the camera is in use. Fix shutter: The selected value will be set as the fixed shutter speed. 1/30 fix, 3/100 fix, 3/120 fix, 2/100 fix, 2/120 fix, 1/100 fix, 1/120 fix, 1/250 fix, 1/500 fix, 1/1000 fix, 1/2000 fix, 1/4000 fix, 1/10000 fix Default: Outdoor scene Note: • When a faster shutter speed is selected (up to 1/10000), it is possible to capture a fast moving object with less blur. • When a faster shutter speed is selected, the sensi- tivity will become lower. Smear also may appear under bright light condition. • When "On" is selected for "Super Dynamic(SD)", only "Outdoor scene" and "Indoor scene" are avail- able. [AGC] Select a method of gain adjustment from the following. On(High)/ On(Mid)/ On(Low): When the luminance of the subject becomes darker, gain will be automati- cally incremented and screen will become brighter. "High", "Mid" and "Low" are indications of gain level. Off: Images will be captured with the fixed gain level. Default: On(High) [Auto slow shutter] The electronic sensitivity enhancement (sensitivity up) can be carried out by adjusting the storage time of the sensor. The following are available for the recording duration. Off(1/30s), Max.2/30s, Max.4/30s, Max.6/30s, Max.10/30s, Max.16/30s Default: Off(1/30s) Important: • When "On" is selected for "Auto slow shutter", frame rate may become lower. Noise or white dots (blemishes) may sometimes appear.

tivity will automatically be increased up to x16. When "Off" is selected for "AGC", this setting is unavailable. [Black & white mode] Select switching between the color mode and the black & white mode from the following. Off: The color mode is selected. On: The black & white mode is selected. Auto1(Normal): The camera automatically switches between the color mode and the black & white mode in accordance with picture brightness (lumi- nance). The black & white mode will automatically be selected when the lighting condition becomes darker, while the color mode will automatically be selected when it becomes brighter. Auto2(IR Light): Suitable when using near-infrared light source at night. Auto3(Super Chrome Compensation(SCC)): Suitable to keep the color mode even under darker light con- dition. The color mode will be carried on by the Super Chrome Compensation (SCC) function even under illumination that is lower than Auto 1. Default: Auto1(Normal) Super Chrome Compensation (SCC) function This function achieves faithful color images using the proprietary color compensation technology that reproduce images even under low illumination where it is usually difficult to capture objects faith- fully. Note: • The operating sound might be heard when changing to black-and-white mode, however it does not indi- cate any malfunction. • Since the color compensation technology is used for Auto 3, some colors may look different from the actual objects depending on the light condition. [Level] Select the threshold illuminance level (brightness) to switch between the color mode and the black & white mode. The descriptions about the following threshold illumi- nance levels are given when "Off" is selected for "Super Dynamic(SD)". • When "Black & white mode" is set to "Auto1" or "Auto2" High: Switches from the color mode to the black & white mode when the ambient brightness (illumi- nance) of the camera is approx. 6 lx or less. Low: Switches from the color mode to the black & white mode when the ambient brightness (illumi- nance) of the camera is approx. 2 lx or less. • When "Black & white mode" is set to "Auto3". High: Carries on the color mode by activating the super chroma compensation function when the ambient brightness (illuminance) of the camera is approx. 6 lx or less. When the color temperature of the object becomes approx. 3 500 K or lower, the color mode will be switched to the black & white mode. Low: Carries on the color mode by activating the super chroma compensation function when the ambient brightness (illuminance) of the camera is approx. 2 lx or less. When the color temperature of the object becomes approx. 3 500 K or lower, the color mode will be switched to the black & white mode. Default: High [Dwell time] Select a wait time for switching between the color mode and the black & white mode from the following. 2s/ 10s/ 30s/ 1min Default: 10s [White balance] Select a method of white balance adjustment from the following. White color can be adjusted by "Red gain" and "Blue gain". ATW1: Selects the automatic tracing white balance mode. The camera will constantly check the color temperature of the light source and adjust the white balance automatically. Operating color temperature range is approx. 2 700 K to 6 000 K. ATW2: Selects the automatic tracing white balance mode under a sodium lamp. The camera will adjust the white balance automatically under a sodium lamp. Operating color temperature range is approx. 2 000 K to 6 000 K. AWC: Selects the automatic white balance control mode. This adjustment is suitable for a location where a light source is stable. Operating color tem- perature range is approx. 2 000 K to 10 000 K. Default: ATW1

faithfully processed. In these cases, select "AWC". • When shooting a subject whose major part is a thick color • When shooting blue sky or sun at sunset • When shooting a subject whose luminance is too low • When "AWC" is selected, click the [Set] button. [Red gain] Adjust the red color of images. When the cursor is moved in the "+" direction, the red color will become thicker. When the cursor is moved in the "–" direction, the red color will be thinner. Click the [Reset] button to reset the color to the default. Default: 128 [Blue gain] Adjust the blue color of images. When the cursor is moved in the "+" direction, the blue color will become thicker. When the cursor is moved in the "–" direction, the blue color will be thinner. Click the [Reset] button to reset the color to the default. Default: 128 [DNR] The digital noise reduction function reduces noise auto- matically under the condition of low illuminance. Select an effect level "High" or "Low" for the digital noise reduction. High: High DNR, afterimage remains Low: Low DNR, reduces afterimage Default: High [Stabilizer] Select "On" or "Off" to determine whether or not to activate the image stabilizer. Default: Off Important: • If "On" is selected for the image stabilizer, the view angle will become narrower and the resolution becomes lower. When "On" is selected, check the view angle and resolution at camera installation. The image stabilizer function may not work for the fol- lowing photographic subjects: • Dark subject • Less contrast subject (e.g. white wall) • Short cycled image shaking such as mechanical vibration • Large amplitude image shaking • Image stabilization may not be effective in the following case. • Image stabilization may not be effective in the fol- lowing case. • When a parameter other than "Off(1/30s)" is selected for "Auto slow shutter" [Chroma gain level] Adjusts the chroma level (color density). When the cursor is moved in the "+" direction, the col- ors will become thicker. When the cursor is moved in the "–" direction, the colors will be thinner. Click the [Reset] button to reset the color to the default. Default: 128 [Aperture level] Adjust the aperture level (outline compensation). Images will be sharper when the cursor is moved in the "+" direction, and will be softer when the cursor is moved in the "–" direction. Click the [Reset] button to reset the color to the default. Default: 20 [Pedestal level] Adjust the black level of images by moving the cursor. When the cursor is moved to the "+" direction, images will become brighter. When the cursor is moved to the "–" direction, images will be darker. Click the [Reset] button to reset the color to the default. Default: 128 [Close] button Click this button to quit the "Image adjust" setup menu.

menu) SC384 Click the [Setup >>] button of "Image adjust" on the [Image/Position] tab of the "Image/Audio" page. (☞ page 58) The settings relating to image quality can be configured with the setup menu displayed in a newly displayed win- dow. When the values are changed, the changed values will be applied to the currently displayed image on the [Image/Position] tab. [Wide dynamic range(WDR)] Select "On" or "Off" to determine whether or not to activate the wide dynamic range function. This function compensates brightness so that it pro- duces clearer images even if objects have various illu- mination intensities. On: The wide dynamic range function will work. Off: The wide dynamic range function will not work. Default: Off Note: • When the wide dynamic range function is activated, noise may be increased in the dark area of the object. • When "Outdoor scene" or "Indoor scene" is selected for "Light control mode", this setting is available. [Face WDR] The "Face WDR" setting can calibrate the illuminance level of people's faces on images to improve the visibil- ity by synchronizing the face detection function with the wide dynamic range function when their faces are too dark to recognize. Select "On" or "Off" to determine whether or not to interact with the face detection function. On: The interactive control with face detection will work. The wide dynamic range controls over around face. Off: The interactive control with face detection will not work. Default: Off Note: • When "Off" is selected for "Wide dynamic range", it is impossible to activate the "Face WDR" setting. • There may be some cases that the effect is not dis- tinct when the faces are too dark to recognize due to strong backlight. [Adaptive black stretch] Select "On" or "Off" to determine whether or not to activate the darkness compensation function. The dark- ness compensation function can make darker parts of images brighter by digital image processing. On: Activates the darkness compensation function. Off: Deactivates the darkness compensation function. Default: Off Important: • When "On" is selected for "Adaptive black stretch", noise in the darker parts may be increased, and parts around borders between the darker parts and the brighter parts may become darker/brighter than the other darker/brighter parts. Note: • When "On" is selected for "Wide dynamic range", the "Adaptive black stretch" setting is unavailable.

Select "On" or "Off" to determine whether or not to activate the back light compensation (BLC) function. When "On" is selected for "Wide dynamic range", this setting is unavailable. The back light compensation function can compensate back light by setting mask areas on brighter parts of images brighter. On: Mask areas will be set automatically. Off: Mask areas will not be set automatically. It is nec- essary to set them manually. Default: Off [Mask area] When "Off" is selected for "Wide dynamic range" and "Back light compensation(BLC)", it is possible to com- pensate for backlight by masking brighter areas. Refer to page 66 for information on how to set the mask area. [Light control mode] Select the light control mode from the following. Outdoor scene: Depending on the brightness level (illuminance), the iris will automatically be controlled together with the shutter speed adjustment to con- trol light. When shooting a bright subject such as outdoor, etc., select this parameter. Be aware that flicker may occur when a subject is under fluores- cent lighting. Indoor scene (60 Hz) Indoor scene (50 Hz): The shutter speed will automati- cally be adjusted to prevent flicker caused by fluo- rescent light. Select 50 Hz or 60 Hz corresponding to the location where the camera is in use. Fix shutter: The selected value will be set as the fixed shutter speed. 1/30 fix, 3/100 fix, 3/120 fix, 2/100 fix, 2/120 fix, 1/100 fix, 1/120 fix, 1/250 fix, 1/500 fix, 1/1000 fix, 1/2000 fix, 1/4000 fix, 1/10000 fix Default: Outdoor scene Note: • When a faster shutter speed is selected (up to 1/10000), it is possible to capture a fast moving object with less blur. • When a faster shutter speed is selected, the sensi- tivity will become lower. Smear also may appear under bright light condition. • When "On" is selected for "Wide dynamic range", only "Outdoor scene", "Indoor scene (60Hz)" and "Indoor scene (50Hz)" are available. [AGC] Select a method of gain adjustment from the following. On(High)/ On(Mid)/ On(Low): When the luminance of the subject becomes darker, gain will be automati- cally incremented and screen will become brighter. "High", "Mid" and "Low" are indications of gain level. Off: Images will be captured with the fixed gain level. Default: On(High) [Auto slow shutter] The electronic sensitivity enhancement (sensitivity up) can be carried out by adjusting the storage time of the sensor. The following are available for the recording duration. Off(1/30s), Max.2/30s, Max.4/30s, Max.6/30s, Max.10/30s, Max.16/30s Default: Off(1/30s) Important: • When "On" is selected for "Auto slow shutter", frame rate may become lower. Noise or white dots (blemishes) may sometimes appear. Note: • When "Max.16/30s" is selected, for example, sensi- tivity will automatically be increased up to x16. When "Off" is selected for "AGC", this setting is unavailable. [Simple Black & white mode] Select switching between the color mode and the black & white mode from the following. Off: The color mode is selected. Auto: Switches from color to black-and-white images when the ambient brightness (illuminance) of the camera is approx.0.2 lx or less. Default: Off

following. White color can be adjusted by "Red gain" and "Blue gain". ATW1: Selects the automatic tracing white balance mode. The camera will constantly check the color temperature of the light source and adjust the white balance automatically. Operating color temperature range is approx. 2700 K - 6000 K. ATW2: Selects the automatic tracing white balance mode under a sodium lamp. The camera will adjust the white balance automatically under a sodium lamp. Operating color temperature range is approx. 2000 K - 6000 K. AWC: Selects the automatic white balance control mode. This adjustment is suitable for a location where a light source is stable. Operating color tem- perature range is approx. 2000 K - 10000 K. Default: ATW1 Note: • Under the following conditions, color may not be faithfully processed. In these cases, select "AWC". • When shooting a subject whose major part is a thick color • When shooting blue sky or sun at sunset • When shooting a subject whose luminance is too low • When "AWC" is selected, click the [Set] button. [Red gain] Adjust the red color of images. When the cursor is moved in the "+" direction, the red color will become thicker. When the cursor is moved in the "–" direction, the red color will be thinner. Click the [Reset] button to reset the color to the default. Default: 128 [Blue gain] Adjust the blue color of images. When the cursor is moved in the "+" direction, the blue color will become thicker. When the cursor is moved in the "–" direction, the blue color will be thinner. Click the [Reset] button to reset the color to the default. Default: 128 [DNR] The digital noise reduction function reduces noise auto- matically under the condition of low illuminance.Select an effect level "High" or "Low" for the digital noise reduction. High: High DNR, afterimage remains Low: Low DNR, reduces afterimage Default: High [Chroma gain level] Adjusts the chroma level (color density). When the cursor is moved in the "+" direction, the col- ors will become thicker. When the cursor is moved in the "–" direction, the colors will be thinner. Click the [Reset] button to reset the color to the default. Default: 128 [Aperture level] Adjust the aperture level (outline compensation). Images will be sharper when the cursor is moved in the "+" direction, and will be softer when the cursor is moved in the "–" direction. Click the [Reset] button to reset the color to the default. Default: 16 [Pedestal level] Adjust the black level of images by moving the cursor. When the cursor is moved to the "+" direction, images will become brighter. When the cursor is moved to the "–" direction, images will be darker. Click the [Reset] button to reset the color to the default. Default: 128 [Close] button Click this button to quit the "Image adjust" setup menu.

When "Off" is selected for "Wide dynamic range (WDR)" SC384 , or "Super Dynamic(SD)" SW395 SC385 and "Back light compensation(BLC)", it is possible to compensate for backlight by masking brighter areas. Step 1 Display the "Image adjust" setup menu. (☞ Page 58) Step 2 Click the [Start] button of "Mask area". → Borders will appear and the image displayed on the [Image/Position] tab will be divided into 48 (6x8). Step 3 Click the divided areas to be masked. → The clicked areas will be masked and will become white. To cancel masking, click the area again. Step 4 Click the [End] button after completing masking areas. → The borders on the image displayed on the [Image/ Position] tab will disappear. SW395 SC385 SC384

JPEG/H.264, the image will be displayed clipped from the image of "4:3".Therefore even when "16:9" is set, the brightness of the masked area will affect the image. It is recommended that the aspect ratio should be once set to "4:3" before masking. Note: • When the [Reset] button is clicked, masking for all the masked areas will be canceled. Configure the settings relating to the preset positions ("Preset position" setup menu) Click the [Setup>>] button of "Preset position" on the [Image/Position] tab of the "Image/Audio" page (☞ page 58). It is possible to register, edit and delete the preset positions on this page. When the focus, brightness, zoom factor are adjusted, the adjustment will be applied immediately to the currently displayed image on the [Image/Position] tab. SW395 SC385 SC384 Image in the aspect ratio of "4:3" Areas where the image is not displayed when "16:9" is selected for the aspect ratio Image in the aspect ratio of "16:9" (Being cut out from the aspect ratio of 4:3)

[Preset ID] Select "On" or "Off" to determine whether to enable or disable the preset ID display. This function can be applied to each preset position. On: Displays the preset ID. Off: Does not display the preset ID. Default: Off Important: • When "Preset ID (0-9, A-Z)" or "Preset ID" is config- ured, it is necessary to click the [Set] button to apply them. Note: • When "On" is selected, the entered preset ID will be displayed at the position selected for "OSD Position" on the [Basic] tab of the "Basic" page. (☞ Page 31) [Preset ID (0-9, A-Z)] Enter the preset ID to be displayed on images. This function can be applied to each preset position. Available characters: 0-9, A-Z and the following marks. ! " # $ % & ' ( ) * + - , . / ; : = ? Available number of characters: 0 - 20 characters Default: None (blank) Note: • The entered preset ID will be displayed next to the preset position number on the pull-down menu. When "On" is selected for "Preset ID", the preset ID will be displayed on images. [Auto focus] Select "Auto" or "Off" to determine whether to enable or disable the auto focus function after the camera has moved to a preset position. This function can be applied to each preset position. Auto: The auto focus function will be activated after moving to a preset position. Off: Does not activate the auto focus function after moving to a preset position. Default: Off Important: • When the zoom factor is 36x or more, the setting of the preset positions will become unavailable. Note: • Depending on the environment (such as when the temperature is below 5° C (41 °F), for example), the moving speed of the camera to the preset position may become slower. Register the preset positions Step 1 Select a preset position number. → The selected preset position number will be dis- played in the "Position No" area. When the selected number has already been regis- tered, the camera will move to the selected preset position. Step 2 Move the camera to the desired direction. Step 3 To display the preset ID on the "Live" page, select "On" for "Preset ID" and enter the desired position title to be displayed. Step 4 The settings for "Auto focus" and "Dwell time" can be configured for each position independently. Step 5 Click the [Set] button. Step 6 The settings for each item such as "Super Dynamic" can be configured for each position independently. The settings for "Super Dynamic" (Wide dynamic range SC384 ), "Back light compensation(BLC)" and "Mask area" are updated immediately.

ing objects, it is recommended to select "Off", and adjust the focus before registering the preset posi- tions. An object whose contrast is low An object whose depth never changes An object with high luminance such as a spotlight [Dwell time] Select a dwell time (duration the camera stops for at each preset position) for the preset sequence opera- tion. 5s/ 10s/ 20s/ 30s Default: 10s [Wide dynamic range] SC384 Select "On" or "Off" to determine whether or not to activate the wide dynamic range. This function can be applied to each preset position. On: The wild dynamic function will work. Off: The wide dynamic function will not work. Default: Off [Super Dynamic] SW395 SC385 Select "On" or "Off" to determine whether to turn on or off the Super Dynamic function. This function can be applied to each preset position. On: The Super Dynamic function will work. Off: The Super Dynamic function will not work. Default: Off [Back light compensation(BLC)] Select "On" or "Off" to determine whether or not to activate the back light compensation (BLC) function. When "On" is selected for "Super Dynamic" (Wide dynamic range SC384 ), this setting is unavailable. The back light compensation function can compensate back light by setting mask areas on brighter parts of images brighter. On: Mask areas will be set automatically. Off: Mask areas will not be set automatically. It is nec- essary to set them manually. Default: Off [Mask area] When "Off" is selected for "Super Dynamic" (Wide dynamic range SC384 ) and "Back light compensation(BLC)", it is possible to compensate for backlight by masking brighter areas. Refer to page 66 for descriptions of how to mask. [Zoom] buttons, [Focus] buttons, [Brightness] but- tons, Control pad/buttons Refer to pages 9 and 11 for descriptions of how to operate these buttons/pad. [Set] button Registers the preset positions. [Delete] button Deletes the preset position specified by the position number. [Close] button Click this button to close the "Preset position" setup menu.

menu) Click the [Setup>>] button of "Auto pan" on the [Image/Position] tab of the "Image/Audio" page (☞ page 58). The settings relating to the auto pan function can be configured with the setup menu displayed in a newly displayed window. ■ Position [Start position] Move the camera to the desired point to be set as the start point of the auto panning using the control pad/ buttons and adjust the image using the [Zoom] buttons and the [Focus] buttons. The zoom and focus settings are set together with the start point. Note: • Panning, tilting and zooming operations can also be carried out on the [Image/Position] tab. • Adjusted zoom and focus position for the auto pan function will be applied when [Set] button of "Start position" is clicked. [End position] Move the camera to the desired point to be set as the end point of the auto panning using the control pad/ buttons, and then click the [Set] button to register the position as the end position. ■ Auto pan [Dwell time] Select a dwell time at the start point and the end point from the following. 5s/ 10s/ 20s/ 30s Default: 5s [Speed] Select a speed for the auto panning from the following. 3°/s, 4°/s, 5°/s, 7°/s, 10°/s, 13°/s, 18°/s, 24°/s Default: 13°/s Important: • When "Dwell time" or "Speed" is edited, it is neces- sary to click the [Set] button to apply them. Note: • Even when the selected zoom factor is higher than 36x, the camera will start panning with 36x zoom factor. [Zoom] buttons, [Focus] buttons, [Brightness] but- tons, Control pad/buttons and [Go] button Refer to pages 9 and 11 for descriptions of how to operate these buttons/pad. [Close] button Click this button to close the "Auto pan" setup menu.

menu) Click the [Setup>>] button of "Privacy zone" on the [Image/Position] tab of the "Image/Audio" page (☞ page 58). When there is a zone that is not to be displayed, set the zone as a privacy zone to not to display. Up to 8 privacy zones (2 privacy zones SC384 ) can be set. Note: • Depending on the panning/tilting direction (especially when the tilting degree is 45° - 90°) and the zooming fac- tor, the area set as the privacy zone may become visible. Make sure that each of the set privacy zone is not visi- ble after setting it. • The privacy zone function does not work when the camera is in the process of warming-up just after turning on the power, or in the process of refreshing the position. ■ Privacy zone [Display type] Select a display type of the privacy zone from the fol- lowing. Gray: The privacy zones will be displayed in gray. Mosaic: The privacy zones will be displayed with a mosaic effect. SW395 SC385 Off: Does not display the privacy zones. Default: Off ■ Zone setting [Zone select] Click [C] of "Zone No" and select a zone number (1-8) (1, 2 SC384 ) from the pull-down menu. An asterisk (*) next to the zone number indicates that the privacy zone has already been set for the number. A blinking mask will be displayed at the center of the image displayed on the [Image/Position] tab. Operate the camera with the panning/tilting/zooming operations to cover the area to be covered by the blink- ing mask. Click the [Set] button after determining the position of the camera. To delete the registered zone, click the [Delete] button after designating the desired zone number to be deleted. Click the [Cancel] button to cancel the application or to delete the setting. Note: • Set the privacy zone larger than the size of an object to be hidden. To raise the precision of the privacy zone placement especially when the zoom is on the "Wide" side, it is recommended to set the privacy zone with the zoom range between 1x and 3x. • Panning, tilting and zooming operations can also be carried out on the [Image/Position] tab. • When selecting "Zone No" after selecting "Gray" for "Display type", a mask will be displayed at the cen- ter of the image display area and will start blinking while changing its color as follows: Dark gray → Clear → Light gray When the other mask that had already been set is on the same zone, the mask that had previously been set will blink as follows: Dark gray → Light gray • When selecting "Zone No" after selecting "Mosaic" for "Display type", a mask will be displayed at the center of the image display area with a mosaic effect. When the other mask that had already been set is on the same zone, the mask that had previously been set will be displayed in dark gray. SW395 SC385

tons, Control pad/buttons and [Go] button Refer to pages 9 and 11 for descriptions of how to operate these buttons/pad. Configure the settings relating to audio [Audio] Click the [Audio] tab on the "Image/Audio" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The settings relating to audio can be configured on this page. Note: • Images and audio will not be synchronized. Therefore, images and audio may not always match. • Audio may be interrupted depending on the network environment. [Audio transmission/reception] Select the communication mode used for audio data transmission/reception between the camera and the PC from the following. Off: Does not receive/transmit audio between the cam- era and the PC. Therefore, the settings and controls relating to audio will be invalidated. Mic input: The PC receives audio data from the cam- era. Audio can be heard with images on the PC. Images and audio will not be synchronized. Audio output: Audio data from the PC will be transmit- ted to the camera. Audio can be heard from the speaker connected to the camera. Interactive(Half-duplex): Both reception and transmis- sion are available. However, audio data cannot simultaneously be transmitted and received. Interactive(Full-duplex): Both reception and transmis- sion are simultaneously available. Default: Off [Close] button Click this button to close the "Privacy zone" setup menu. Note: • Howling may be generated depending on usage conditions. If howling is generated, prevent sound generated by the PC from entering the PC micro- phone. • When "Multicast" is selected for "Transmission type" on the [JPEG/H.264] (or [JPEG/MPEG-4]) tab of the "Image/Audio" page, audio transmission will become unavailable while monitoring H.264 (or MPEG-4) images. To transmit audio from a PC to the camera, click the [JPEG] button on the "Live" page. [Audio encoding format] Select the audio encoding format from G.726 and G.711. Default: G.726 Note: • i-PRO Series does not support aspect ratio of "G.711". (As of October, 2010) • G. 711 is available only when "Mic input" is selected for "Audio transmission/reception". [Audio bit rate] Select "16kbps" or "32kbps" for the audio bit rate used to transmit/receive audio data. Default: 32kbps Note: • When selecting a smaller value for "Bandwidth control(bit rate)" (☞ page 97) while putting a priority on the JPEG/H.264(MPEG-4) image transmission, select "16kbps" for "Audio bit rate".

selected for "Audio encoding format". [Mic input volume (Camera to PC)] Select a volume level on the PC to hear audio transmit- ted from the camera. Mic High: The volume level will become high. This set- ting will be applied when audio is input to the cam- era using a microphone. Mic Middle: The volume level will become middle. This setting will be applied when audio is input to the camera using a microphone. Mic Low: The volume level will become low. This set- ting will be applied when audio is input to the cam- era using a microphone. Line High: The volume level will become high. This set- ting will be applied when audio is input to the cam- era using the Line input. Line Middle: The volume level will become middle. This setting will be applied when audio is input to the camera using the Line input. Line Low: The volume level will become low. This set- ting will be applied when audio is input to the cam- era using the Line input. Default: Mic Middle [Mic input interval (Camera to PC)] Select an interval for audio reception from the following. 20ms/ 40ms/ 80ms/ 160ms Default: 40ms Note: • When a shorter interval is selected, the delay time will be shorter. When a longer interval is selected, audio interruption may be diminished even though the delay time will be longer. Select the interval according to the network environment. [Audio output volume (PC to Camera)] Select a volume level on the camera to hear audio transmitted from the PC. High/ Middle/ Low Default: Middle [Audio output interval (PC to Camera)] Select an interval for audio transmission from the fol- lowing. 160ms/ 320ms/ 640ms/ 1280ms Default: 640ms Note: • When a shorter interval is selected, the delay time will be shorter. When a longer interval is selected, audio interruption may be diminished even though the delay time will be longer. Select the interval according to the network environment. • Audio may temporarily be interrupted or noise may be heard the camera, or when multiple users are accessing concurrently. It may be possible to dimin- ish the interruption or noise by setting a longer interval for "Audio output interval (PC to Camera)". • Audio may sometimes not be heard depending on the network environment. [Audio output port (PC to Camera)] Enter the transmission port number (the port number on the camera used to receive audio data transmitted from the PC). Available port number: 1024-50000 (Only even num- bers are available.) Default: 34004 Note: • The transmission port number entered for "Audio output port (PC to Camera)" will be used only when "Unicast port (MANUAL)" is selected for "Transmission type" (☞ page 51 and 55). When "Off" is selected for "H.264 transmission" (or "MPEG-4 transmission") (☞ pages 49 and 53) or when "Unicast port (AUTO)" or "Multicast" is selected for "Transmission type", it is not necessary to enter the transmission port number. [Permission level of audio trans./recep.] Select an access level for audio transmission/reception from the following. 1. Level 1 only/ 2. Level 2 or higher/ 3. All users Default: 3. All users Note: • Refer to pages 87 and 88 for further information about the access level.

The cameras from which images are to be displayed on a multi-screen can be registered on the "Multi-screen" page. (☞ Pages 26 and 27: How to display/operate the setup menu) [IP address] Enter the IP address or the host name of the camera to be used for the multi-screen. 4 cameras can be regis- tered as a group and up to 4 groups (16 cameras) can be registered. When the HTTP port number for the camera of which images are to be displayed had been changed, enter as follows: Example of entry: Example when entering an IPv4 address: http://192.168.0.10:8080 Example when entering an IPv6 address: http://[2001:db8:0:0:0:0:0:1]:8080 Available number of characters: 1 - 128 characters To access the cameras using the HTTPS protocol, enter as follows: Example of entry: https://192.168.0.10/ Important: • When accessing the camera using the HTTPS pro- tocol, install the security certificate of the camera to display images on the monitor. (☞ Page 106) Note: • When using the host name, it is necessary to con- figure the DNS settings of the PC to be used for the multi-screen display. (☞ Page 94) [Camera title] Enter the title of the camera. The entered camera title will be displayed on a multi-screen. Available number of characters: 0 - 20 characters Unavailable characters: "& Note: • When selecting a 16 split-screen, some characters of the camera title to be displayed may not be dis- played. • Even when "16:9" is selected for "Aspect ratio", the multi-screen is displayed in 4:3.

The settings relating to alarm occurrences such as settings for the alarm action at an alarm occurrence, the VMD area settings, and the alarm occurrence notification can be configured on this page. The "Alarm" page has 3 tabs; the [Alarm] tab, the [VMD area] tab and the [Notification] tab. Configure the settings relating to the alarm action [Alarm] Click the [Alarm] tab on the "Alarm" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The settings relating to the alarm can be configured in this section. Refer to pages 77 and 79 for further information about the settings relating to the alarm images and the alarm output terminal. ■ Alarm [Terminal 1] Determine how to use terminal 1. Off: Not used. Alarm input: Receives alarms. Black & white input: Receives the black & white swi- tchover input. (When the input is set to On, the black & white mode is activated.) SW395 SC385 Default: Off [Terminal 2] Determine how to use terminal 2. Off: Not used. Alarm input: Receives alarms. Alarm output: Alarm output will be carried out accord- ing to the settings for "Alarm output terminal setup" (☞ page 79). Default: Off [Terminal 3] Determine how to use terminal 3. Off: Not used. Alarm input: Receives alarms. AUX output: AUX output will be supplied. The [AUX] buttons will be displayed on the "Live" page. Default: Off Note: • AUX is a camera terminal that allows users to oper- ate (Open/Close) arbitrarily from the "Live" page. For example, an operator can remotely control lights in a place where the camera is installed by connect- ing the terminal to the light controller. • Refer to the installation guide for further information about input/output rating of each terminal. • While "Alarm input" is being selected, an alarm is detected when the terminal status is changed to "On". (Default) It is possible to configure the setting so that an alarm is detected when the terminal status is changed to "Off". Refer to the "Readme" file on the provided CD-ROM for further information about the setting. Or refer to our website (http://panasonic. net/pss/security/support/info.html) for further infor- mation about the supported software. [VMD alarm] When clicking "VMD >>", the [VMD area] tab of the "Alarm" page will be displayed. [Command alarm] Select "On" or "Off" to determine whether or not to receive the command alarm. The command alarm is the function that provides notifi- cation of a Panasonic protocol alarm from the other cameras. When "On" is selected, alarm actions will be performed between multiple cameras. Default: Off [Originating port number] Select a port number to be used to receive the com- mand alarm. Available range: 1-65535 Unavailable port number: Refer to the help window. Default: 8181

occurrence [Alarm] Click the [Alarm] tab on the "Alarm" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The settings relating to the camera action at an alarm occurrence can be configured in this section. Refer to pages 75, 77 and 79 for further information about the settings relating to the alarm, the alarm image and the alarm output terminal. ■ Camera action on alarm [Terminal alarm 1] Select an action to be taken when a terminal alarm 1 is detected from the following. Off: Does not take any action even when a terminal alarm 1 is detected. 1-64: When the registered preset position is selected, the camera will move to the selected preset position when a terminal alarm 1 is detected. Auto track SW395 SC385 : When a terminal alarm 1 is detected, the camera will start the auto tracking. Default: Off [Terminal alarm 2] Select an action to be taken when a terminal alarm 2 is detected from the following. Off: Does not take any action even when a terminal alarm 2 is detected. 1-64: When the registered preset position is selected, the camera will move to the selected preset position when a terminal alarm 2 is detected. Auto track SW395 SC385 : When a terminal alarm 2 is detected, the camera will start the auto tracking. Default: Off [Terminal alarm 3] Select an action to be taken when a terminal alarm 3 is detected from the following. Off: Does not take any action even when a terminal alarm 3 is detected. 1-64: When the registered preset position is selected, the camera will move to the selected preset position when a terminal alarm 3 is detected. Auto track SW395 SC385 : When a terminal alarm 3 is detected, the camera will start the auto tracking. Default: Off [VMD alarm] Select an action to be taken when a VMD alarm is detected from the following. Off: Does not take any action even when a VMD alarm is detected. 1-64: When the registered preset position is selected, the camera will move to the selected preset position when a VMD alarm is detected. Auto track SW395 SC385 : When a VMD alarm is detected, the camera will start the auto tracking. Default: Off [Command alarm] Select an action to be taken when a command alarm is detected from the following. Off: Does not take any action even when a command alarm is detected. 1-64: When the registered preset position is selected, the camera will move to the selected preset position when a command alarm is detected. Auto track SW395 SC385 : When a command alarm is detected, the camera will start the auto tracking. Default: Off

Click the [Alarm] tab on the "Alarm" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The settings relating to the alarm image to be transmitted to an FTP server can be configured in this section. The alarm image will be transmitted to an FTP server. To transmit alarm images to an FTP server, it is necessary to con- figure the settings in advance. (☞ Page 91) Important: • Depending on the network line speed or the network traffic, images may not be transmitted at the exact desig- nated interval or period. • When "Alarm input" or "Manual" is selected for "Save trigger" on the [SD memory card] tab, images will not be transmitted to the FTP server even when an alarm is detected. (☞ Page 34) ■ Alarm image [FTP >>] When "FTP >>" is clicked, the [FTP] tab of the "Server" page will be displayed. (☞ Page 91) [Alarm image FTP transmission] Select "On" or "Off" to determine whether or not to transmit the alarm image to the FTP server. Default: Off [Directory name] Enter the directory name where the alarm images are to be saved. For example, enter "/ALARM" to designate the direc- tory "ALARM" under the root directory of the FTP server. Available number of characters: 1 - 256 characters [File name] Enter the file name used for the alarm image to be transmitted to an FTP server. The file name will be as follows. File name: ["Entered file name" + "Time and date (year/ month/ day/ hour/ minute/ second)"] + "Serial number" Available number of characters: 1 - 32 characters [Post alarm] • Transmission interval Select the transmission interval for the alarm image transmission to the FTP server from the following. 0.1fps/ 0.2fps/ 0.33fps/ 0.5fps/ 1fps Default: 1fps • Number of images Select the number of images to be transmitted from the following. 1pic/ 2pics/ 3pics/ 4pics/ 5pics/ 6pics/ 7pics/ 8pics/ 9pics/ 10pics/ 20pics/ 30pics/ 50pics/ 100pics/ 200pics/ 300pics/ 500pics/ 1000pics/ 2000pics/ 3000pics Default: 100pics • Recording duration Approximate time to be taken to save the set "Number of images" with the set "Transmission interval" will be displayed. [Image capture size] Select the capture size of images to be transmitted to the FTP server or of an image to be attached to the alarm mail. When "4:3(VGA)" is selected for "Aspect ratio" QVGA/ VGA/ 1280x960 When "4:3(800x600)" is selected for "Aspect ratio" SW395 SC385 QVGA/ 800x600/ 1280x960 When "16:9" is selected for "Aspect ratio" 320x180/ 640x360/ 1280x720 Default: VGA

Select "On" or "Off" to determine whether or not to change the image quality of the quality 1 upon alarm detection. On: Images will be transmitted with the image quality selected for "Image quality upon alarm detection". Off: Does not change the image quality upon alarm detection. Default: Off [Image quality upon alarm detection] Image quality can be changed upon an alarm occur- rence. Select the image quality from the following. 0 Super fine/ 1 Fine/ 2/ 3/ 4/ 5 Normal/ 6/ 7/ 8/ 9 Low Default: 5 Normal Configure the settings relating to H.264 recording [Alarm] Click the [Alarm] tab on the "Alarm" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The settings relating to the recording H.264 data on the SD memory card when an alarm is detected can be config- ured on this page. To operate recording, it is necessary to configure the settings relating to SD memory card and the moving picture data. (☞ Page 33) ■ H.264 recording [Pre alarm] Determine whether or not to perform the pre-alarm recording. When "Use" is selected, 1 MB image data is always saved during the pre alarm recording. Use/ Not use Default: Not use [Post alarm (recording) duration] Set the duration to save image data on the SD memory card after an alarm occurrence. 10s/ 20s/ 30s/ 40s/ 50s/ 60s/ 120s/ 180s/ 240s/ 300s Default: 30s * The actual recording time may sometimes be longer than the duration selected for this setting. [Recording (memory) Size per an alarm] The capacity of the SD memory card used to record video data upon an alarm occurrence. The actual capacity may be different. Important: • To record H.264 data, it is required to select "Use" for "SD memory card" on the [SD memory card] tab. In addition, it is select "H.264" for "Recording for- mat". (☞ Page 33)

[Alarm] Click the [Alarm] tab on the "Alarm" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The settings relating to the alarm output terminal can be configured in this section. ■ Alarm output terminal setup [Alarm output trigger] Select "On" or "Off" to determine whether or not to out- put the alarm signals to the alarm output terminal when an alarm is detected. Default: Off [Alarm output type] Select "Latch" or "Pulse" for the alarm output terminal at an alarm occurrence. Latch: When an alarm is detected, the alarm output terminal will be in the state selected for "Trigger out- put" until the alarm occurrence indication button is clicked. Pulse: When an alarm is detected, the alarm output ter- minal will be in the state to the "Trigger output" set- ting for the period set for "Pulse width". When the alarm occurrence indication button is clicked, the alarm output terminal will return to the normal state. Default: Latch [Trigger output] Select "Open" or "Close" to determine whether to open or close the alarm output terminal when outputting the alarm signals. Open: The alarm output terminal will open when out- putting the alarm signals. (Normally close) Close: The alarm output terminal will close when out- putting the alarm signals. (Normally open) Default: Close Note: • When "Open" is selected, the alarm signal will be output for around 20 seconds when the power of the unit is turned on. [Pulse width] When "Pulse" is selected for "Alarm output", select an alarm output terminal duration from the following. Available range: 1-120s Default: 1s

Click the [Alarm] tab on the "Alarm" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The names of "AUX", "Open" and "Close" on the "Live" page can be changed. ■ AUX title [AUX (Up to 10 characters)] Enter the name for "AUX" on the "Live" page. Default: AUX [Open (Up to 5 characters)] Enter the name for "Open" of "AUX" on the "Live" page. Default: Open [Close (Up to 5 characters)] Enter the name for "Close" of "AUX" on the "Live" page. Default: Close Note: • AUX is a camera terminal that allows users to oper- ate (Open/Close) arbitrarily from the "Live" page. For example, an operator can remotely control lights in a place where the camera is installed by connect- ing the terminal to the light controller. Configure the VMD settings [VMD area] Click the [VMD area] tab on the "Alarm" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The video motion detection areas can be set on this page. The VMD areas can be set for each preset position (up to 4 areas, 64 preset positions). When motion is detected in the set area, it will be regarded as an alarm. The camera can be configured to take an alarm action even when the camera is not at the preset position. Important: • The alarm occurrence indication button (☞ page 11) will be displayed when motion is detected by the VMD function. • The alarm occurrence indication button will be displayed when receiving an alarm input of a terminal alarm or a command alarm. • Depending on the network environment, notification may be delayed even when "Real time" is selected for "Alarm status update mode" on the [Basic] tab of the "Basic" page (☞ page 32). • The motion detection function is not the dedicated function to prevent thefts, fires, etc. We are not responsible for any accidents or damages occurring in case.

[Select a preset position] Select a preset position number to which the VMD area is to be set, and click the [Start] button. (☞ Page 82) When setting an area which is not at the preset position for the VMD area, select VMD activation in area "except the preset positions". [Area] When selecting a VMD area in the screen, it will be numbered as area 1. (Subsequent areas will be num- bered in the order of selection.) [All areas] button When the [All areas] button is clicked, the whole area will become the VMD area, and "1 (White)" will be auto- matically applied to "Area". [Status] Select "On" or "Off" to determine whether or not to activate each VMD area. On: Activates the respective VMD area. Off: Inactivates the respective VMD area. Default: Off [Detection area] Adjust the size of the VMD area using the slider. The smaller the selected value is, the higher the sensitivity of VMD area becomes. The current value (1-10) will be displayed on the right of the slider. Default: 1 [Detection sensitivity] Adjust the sensitivity of motion detection in the VMD area using the slider. The settings can be configured for each area individually. The larger the value is set, the higher the sensitivity level becomes. The current value (1 (low) - 15 (high)) will be displayed below the slider. Default: 8 [Delete] button Click the [Delete] button corresponding to the area to be deleted. The outline of the selected area will be deleted. [Light detection control] Select "On" or "Off" to determine whether or not to detect video motion affected by brightness change such by a dimming level control. Default: Off Important: • "Light detection control" may not work when bright- ness change is too small. • When "On" is selected for "Light detection control", the video motion detection may not be performed even when detecting a subject moving over the whole screen. ■ VMD information addition [Information addition] Select "On" or "Off" to determine whether or not to add VMD information to superimposed image data. The VMD information can be searched by some Panasonic network disk recorders. Refer to the operat- ing instructions of the connected devices for further information about the functions and settings. Default: Off

Set the areas to activate the VMD function. Important: • When the settings are being configured on the setup menu, sometimes the VMD function may not work cor- rectly. Step 1 Set the video motion detection area by dragging the mouse on the screen. When the [All areas] button is clicked, the whole area will become the VMD area, and "1 (White)" will be auto- matically applied to "Area". → The designated area will become the VMD area "1(White)" and the outline will be displayed. When 2 - 4 VMD areas are set, each area will be numbered in order. The areas will be identified by the respec- tive outline colors. The "Status" of the outline to be set for the area will become "On". Step 2 Adjust "Detection area" and "Detection sensitivity" using the slider. "Detection area" can be adjusted by moving the slider between the left end position and the center position. "Detection sensitivity" can be adjusted by moving the slider between the left end position and the right end position. Refer to page 81 for further information about the "Detection sensitivity" and "Detection area". The status bar will be indicated in the "Detection area" section to show the motion detection status of the cur- rently displayed area. When the status bar exceeds the setting position of slider, the alarm action will be performed. Note: • When "Detection area" cannot be adjusted properly by moving the slider, adjust "Detection sensitivity" while checking the motion detection status. Step 3 Click the [Set] button after completing the settings. Important: • The setting will not be applied unless the [Set] but- ton is clicked. Step 4 To invalidate the VMD area, click the [Set] button after selecting "Off" for "Status" of the VMD area to be invali- dated. → The outline of the invalidated VMD area will turn to a dotted line. When the VMD area is invalidated, no alarm will occur even when a motion can be recog- nized in the area. Step 5 To delete the VMD area, click the [Delete] button corre- sponding to the area to be deleted. → The outline of the respective VMD area will disap- pear. Step 6 Click the [Set] button. → The edited settings will be applied. Step 7 Click the [Back] button to return to the screen to select a preset position.

[Notification] Click the [Notification] tab on the "Alarm" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The settings relating to the alarm mail can be configured. It is necessary to configure the settings of the mail server to perform the mail notification. (☞ Page 90) ■ Mail notification [Mail server >>] When "Mail server >>" is clicked, the [Mail] tab of the "Server" page will be displayed. (☞ Page 90) [Mail notification] Select "On" or "Off" to determine whether or not to pro- vide notification by e-mail according to the settings for the "Alarm" and "Diag." checkboxes of "Destination of notification" below. • When an alarm is detected ("Alarm") • When a notification of the remaining capacity of the SD memory card has been provided ("Diag.") • When the SD memory card has become full ("Diag.") • When the SD memory card cannot be recognized ("Diag.") Default: Off [Alarm image attachment] Select "On" or "Off" to determine whether or not to attach an image to the mail to be sent when an alarm is detected. Default: Off Note: • The settings for "Image capture size" of the "Alarm image" section on the [Alarm] tab (☞ page 77) will be applied to the size of the image to be attached. ■ Destination of notification [Address 1] - [Address 4] Enter the destination mail address. Up to 4 destination addresses can be registered. "Alarm" checkbox: When the checkbox is checked, the mail notification will be performed upon an alarm occurrence. "Diag." checkbox: When the checkbox is checked, the mail notification will be provided in the following cases. • When notification of the remaining capacity of the SD memory card has been provided • When the SD memory card has become full • When the SD memory card cannot be recognized "Destination address": Enter the destination address. Available number of characters: 3 - 128 charac- ters To delete the registered address, click the [Delete] but- ton respective to the desired address. [Mail subject] Enter the mail subject. Available number of characters: 0 - 50 characters [Mail body] Enter the mail body. Available number of characters: 0 - 200 characters Note: • Notification mail will be sent with the message "The capacity of the SD memory card is full." when the SD memory card becomes full, or "The SD memory card cannot be detected." when mounting of the SD memory card failed.

[Notification] Click the [Notification] tab on the "Alarm" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The settings relating to Panasonic alarm protocol can be configured in this section. ■ Panasonic alarm protocol notification [Panasonic alarm protocol] Select "On" or "Off" to determine whether or not to pro- vide notification by Panasonic alarm protocol according to the settings for the "Alarm" and "Diag." checkboxes of "Destination of notification" below. • When an alarm is detected ("Alarm") • When a notification of the remaining capacity of the SD memory card has been provided ("Diag.") • When the SD memory card has become full ("Diag.") • When the SD memory card cannot be recognized ("Diag.") Default: Off Note: • When "On" is selected, notification of the alarm occurrence will be provided to the registered desti- nation addresses in order (to IP address 1 first, to IP address 8 last). [Destination port] Select a destination port for the Panasonic alarm proto- col from the following. Available range: 1 - 65535 Unavailable port number: Refer to the help window. Default: 1818 [Retry times] Select a retry time for the Panasonic alarm protocol. Available range: 0-30 Default: 2 ■ Destination of notification [Address 1] - [Address 8] Enter the destination IP address of the Panasonic alarm protocol from the following. Host name is unavailable for the IP address. Up to 8 destination addresses can be registered. "Alarm" checkbox: When the checkbox is checked, the Panasonic alarm notification will be provided upon an alarm occurrence. "Diag." checkbox: When the checkbox is checked, notification using Panasonic alarm protocol will be provided in the following cases. • When notification of the remaining capacity of the SD memory card has been provided • When the SD memory card has become full • The SD memory card cannot be recognized "Destination IP address": Enter the destination address. To delete the registered IP address, click the [Delete] button respective to the desired IP address. Important: • Confirm that the destination IP addresses are regis- tered correctly. When a registered destination does not exist, notification may be delayed.

recognition [Advanced func.] The setting relating to the XML notification, destinations of information about the face detection and the settings relating to the face detection can be configure on the "Advanced func." page. The "Advanced func." page has 2 tabs; the [XML notification] tab and the [Face detection] tab. Configure the settings relating to the XML notification [XML notification] Click the [XML notification] tab on the "Advanced func." page. The settings relating to the XML notification can be configured in this section. ■ XML notification [XML notification] Select "On" or "Off" to determine whether or not to notify face detection information using XML. Default: Off [Notification interval] Select "1s" or "2s" for the notification interval. Default: 1s Configuration of the destination settings of the face detection [XML notification] Click the [XML notification] tab on the "Advanced func." page. The destination settings of the face detection information can be configured. The XML notification notifies the server of face detection information in XML format. ■ Destination setting for XML notification [Destination address] Configure the IP address or the host name of the desti- nation for XML notification of the face detection infor- mation. Available number of characters: 1 - 128 characters [Destination port number] Configure the port number settings for XML notification of the face detection information. Refer to the help window for information about the unavailable port number.

Configure the settings for the destination directory to be used for the XML notification of the face detection. [User name] Enter a user name. Available number of characters: 0 - 32 characters Default: None (blank) Configuration of the settings relating to the face detection [Face detection] Click the [Face detection] tab on the "Advanced func." page. The settings relating to displaying the frame to be used for the face detection and the settings relating to the face detection information attached to the image can be configured. Important: • The face detection function shall not guarantee the detection of faces in an image. The face detection accuracy varies with imaging conditions. [Password] Enter a password. Available number of characters: 0 - 32 characters Default: None (blank) ■ Face detection [Face detection] Determine whether or not to enable the face detection function. On: Information about the face detection frame will be attached and the test frame will be displayed on the image of this page. Off: Information about the face detection frame will not be attached. No face detection frame will be dis- played on the image of this page. Default: Off Important: • When "Mosaic" is selected for "Display type" of "Privacy zone", the face detection function may sometimes be triggered (the face detection frame will be displayed). SW395 SC385 [XML notification] The destination settings of the face detection informa- tion can be configured. When clicking "XML notification>>", the [XML notifica- tion] tab will be displayed. (☞ Page 85)

authentication [User mng.] The settings relating to the authentication such as users and PCs restrictions for accessing the camera can be con- figured on the "User mng." page. The "User mng." page has 3 tabs; the [User auth.] tab, the [Host auth.] tab and the [System] tab. Configure the settings relating to the user authentication [User auth.] Click the [User auth.] tab on the "User mng." page. (☞ Pages 26 and 27: How to display/operate the setup menu) The settings relating to the authentication of users who can access this camera from the PC or a cellular phone can be configured on this page. Up to 18 users can be registered. Note: • When user authentication (authentication error) has failed to pass 8 times within 30 seconds using the same IP address (PC), access to the unit will be denied for a while. [User auth.] Select "On" or "Off" to determine whether or not to authenticate the users. Default: Off [User name] Enter a user name. Available number of characters: 1 - 32 characters Default: None (blank) [Password] [Retype password] Enter a password. Available number of characters: 4 - 32 characters Default: None (blank) Note: • When the user name already in use is entered and the [Set] button is clicked, the respective user infor- mation will be overwritten. [Access level] Select the access level of the user from the following. 1. Administrator: Allowed all available operations of the camera. 2. Camera control: Allowed to display images from the camera and to control the camera. The camera set- ting configuration is unavailable. 3. Live only: Only displaying live images is available. The camera setting configuration and camera con- trol are unavailable. Default: 3. Live only [User check] By clicking [C] of "User check", the registered user can be selected and the selected user’s information can be checked. The registered user will be displayed with the access level. (Example: admin [1]) To delete the registered user, click the [Delete] button after selecting the user to be deleted.

[Host auth.] Click the [Host auth.] tab on the "User mng." page. (☞ Pages 26 and 27: How to display/operate the setup menu) The restriction settings of PCs (IP address) from accessing the camera can be configured on this page. [Host auth.] Select "On" or "Off" to determine whether or not to authenticate the host. Default: Off [IP address] Enter the IP address of the PC to be allowed to access the camera. Host name cannot be entered for the IP address. Note: • When "IP address/subnet mask" is entered, it is possible to restrict PCs in each subnet. For example, when "192.168.0.1/24" is entered and "2. Camera control" is selected for the access level, the PCs whose IP address is between "192.168.0.0" - "192.168.0.255" can access the camera with the access level "2. Camera control". • When the IP address already in use is entered and the [Set] button is clicked, the respective host infor- mation will be overwritten. [Access level] Select the access level of the host from the following. 1. Administrator/ 2. Camera control/ 3. Live only Refer to page 87 for further information about the access level. Default: 3. Live only [Host check] By clicking [C] of "Host check", the registered host can be selected and the selected host’s IP address can be checked. The registered IP address will be displayed with the access level. (Example: 192.168.0.21 [1]) To delete the registered host, click the [Delete] button after selecting the IP address to be deleted.

Click the [System] tab on the "User mng." page. (☞ Pages 26 and 27: How to display/operate the setup menu) The description below is the configuration of the priority stream that can transmit images without deteriorating the image quality and refresh interval even when multiple users access concurrently. ■ Priority stream [Activation] Select "On" or "Off" to determine whether or not to use the priority stream. Default: Off Note: • When "On" is selected for "Activation" of "Priority stream", number of users who can access the cam- era may be limited. [Destination IP address (1)] Enter the first destination IP address. [Destination IP address (2)] Enter the second destination IP address. [Stream type] Select either "JPEG", "H.264/MPEG-4(1)" or "H.264/ MPEG-4(2)". JPEG: JPEG images will be transmitted. H.264/MPEG-4(1): H.264 (1) (or MPEG-4(1)) images will be transmitted. H.264/MPEG-4(2): H.264 (2) (or MPEG-4(2)) images will be transmitted. Default: JPEG Note: • When "H.264" is selected for "Recording format", it is impossible to transmit H.264 (2) images. In this case, "H.264/MPEG-4(2)" is invalidated. • When "Best effort" is selected for "Transmission pri- ority" of "H.264 (MPEG-4)", bit rate will vary between the maximum and minimum rates while images are being transmitted. [Refresh interval*] Select the refresh interval from the following. This setting is validated only when "JPEG" is selected for "Stream type". SW395 SC385 0.1 fps/ 0.2 fps / 0.33 fps / 0.5 fps / 1 fps / 2 fps / 3 fps / 5 fps / 6 fps / 10 fps / 12 fps *(PAL only)/ 15 fps * /30 fps * SC384 0.1 fps / 0.2 fps / 0.33 fps / 0.5 fps / 1 fps / 2 fps / 3 fps / 5 fps / 6 fps */ 10 fps */ 12 fps *(PAL only)/ 15 fps * / 30 fps * Default: 1 fps Note: • When "On" is selected for "H.264 (MPEG-4) trans- mission", the transmission interval may be longer than the set value when any value with an asterisk (*) on the right is selected. [Image capture size] Select the image capture size from the following. When "4:3(VGA)" is selected for "Aspect ratio" QVGA/ VGA/ 1280x960 When "4:3(800x600)" is selected for "Aspect ratio" SW395 SC385 QVGA/ 800x600/ 1280x960 When "16:9" is selected for "Aspect ratio" 320x180/ 640x360/ 1280x720 This setting is validated only when "JPEG" is selected for "Stream type". Default: 1280x960

The settings relating to the mail server, the FTP server and the NTP server can be configured on this page. The "Server" page has 3 tabs; the [Mail] tab, the [FTP] tab and the [NTP] tab. Configure the settings relating to the mail server [Mail] Click the [Mail] tab on the "Server" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The settings relating to the mail server used to send the alarm mail can be configured on this page. Important: • When a terminal that receives e-mails is not compatible with UTF-8 encode, it is impossible to receive alarm mails correctly. [SMTP server address] Enter the IP address or the host name of the SMTP server used to send e-mails. Available number of characters: 1 - 128 characters [SMTP port] Enter the port number to which e-mails are sent. Available port number: 1-65535 Unavailable port number: Refer to the help window. Default: 25 [POP server address] When "POP before SMTP" is selected for "Type", enter the IP address or the host name of the POP server. Available number of characters: 1 - 128 characters Important: • When entering the host name for "SMTP server address" or "POP server address", it is necessary to configure the DNS settings on the [Network] tab of the "Network" page. (☞ Page 94) [Authentication] • Type Select the authentication method to send e-mails from the following. None: It is not necessary to clear any authentication to send e-mails. POP before SMTP: It is necessary to first clear the POP server authentication to use the SMTP server to send e-mails. SMTP: It is necessary to clear the SMTP server authen- tication to send e-mails. Default: None Note: • When you don't know the authentication method to send e-mails, refer to the network administrator. • User name Enter the user name to access the server. Available number of characters: 0 - 32 characters • Password Enter the password to access the server. Available number of characters: 0 - 32 characters [Sender's mail address] Enter the mail address of a sender. The entered mail address will be displayed in the "From" (sender) line of the sent mails. Available number of characters: 3 - 128 characters

Click the [FTP] tab on the "Server" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The settings relating to the FTP server used to transmit the alarm images can be configured on this page. [FTP server address] Enter the IP address or the host name of the FTP server. Available number of characters: 1 - 128 characters Important: • When entering the host name for "FTP server address", it is necessary to configure the DNS set- tings on the [Network] tab of the "Network" page. (☞ Page 94) [User name] Enter the user name (login name) to access the FTP server. Available number of characters: 1 - 32 characters [Password] Enter the password to access the FTP server. Available number of characters: 0 - 32 characters [Control port] Enter a control port number to be used for the FTP server. Available port number: 1-65535 Unavailable port number: Refer to the help window. Default: 21 [FTP mode] Select "Passive" or "Active" for the FTP mode. Normally, select "Passive". When it is impossible to connect after select "Passive", try to connect after selecting "Active". Default: Passive

Click the [NTP] tab on the "Server" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The settings relating to the NTP server such as the NTP server address, port number, etc. can be configured on this page. Important: • Use an NTP server when the more accurate time & date setting is required for the system operation. [Time adjustment] Select the time adjustment method from the following. Time adjusted by the selected method will be used as the standard time of the camera. Manual: Time set on the [Basic] tab on the "Basic" page will be used as the standard time of the cam- era. Synchronization with NTP server: Time automatically adjusted by synchronizing with the NTP server will be used as the standard time of the camera. Default: Manual [NTP server address setting] When "Synchronization with NTP server" is selected for "Time adjustment", select the method of how to obtain the NTP server address from the following. Auto: Obtains the NTP server address from the DHCP server. Manual: The NTP server address will be entered manu- ally on "NTP server address". Default: Manual Important: • When obtaining the NTP server address from the DHCP server, it is necessary to select "DHCP" or "Auto" for "Network Settings" on the [Network] tab of the "Network" page. (☞ Page 93) [NTP server address] When "Manual" is selected for "NTP server address setting", enter the IP address or the host name of the NTP server. Available number of characters: 1 - 128 characters Default: None (blank) Important: • When entering the host name for "NTP server address", it is necessary to configure the DNS set- tings on the [Network] tab of the "Network" page. (☞ Page 94) [NTP port] Enter a port number of the NTP server. Available port number: 1 - 65535 Unavailable port number: Refer to the help window. Default: 123 [Time adjustment interval] Select an interval (1 - 24 hours: in 1 hour intervals) of synchronization with the NTP server. Default: 1h [Time zone] Select a time zone corresponding to the location where the camera is in use. Default: (GMT) Greenwich Mean Time: Dublin, Edinburgh, Lisbon, London

The network settings and the settings relating to DDNS (Dynamic DNS) and SNMP (Simple Network management Protocol) can be configured on the "Network" page. The "Network" page has 4 tabs; the [Network] tab, the [DDNS] tab, the [SNMP] tab and the [FTP img. trans.] tab. Configure the network settings [Network] Click the [Network] tab on the "Network" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The following information is required to configure the network settings. Contact the network administrator or your Internet service provider. • IP address • Subnet mask • Default gateway (when using the gateway server/router) • HTTP port • Primary DNS address, Secondary DNS address (when using DNS) ■ IPv4 network [Network Settings] Select the method of how to configure the IP address from the following. Static: The IP address is configured by entering manu- ally on "IP address(IPv4)". DHCP: The IP address is configured using the DHCP function. Auto: The IP address is configured using the DHCP function. When the DHCP server is not found, the IP address is automatically configured. Configure the DHCP server not to assign the same IP addresses used for the other network cameras and PCs whose IP address is unique. Refer to the network administrator for further information about the settings of the server. Default: Static Note: • When "Auto" is selected and the IP address cannot be obtained from the DHCP server, an IP address not used in the same network will be searched within 169.254.1.0 - 169.254.254.255. [IP address(IPv4)] When not using the DHCP function, enter the IP address of the camera. Do not enter an IP address already in use (for the PCs and the other network cam- eras). Default: 192.168.0.10

using the DHCP function. Refer to the network administrator for further information about the set- tings of the DHCP server. [Subnet mask] When not using the DHCP function, enter the subnet mask of the camera. Default: 255.255.255.0 [Default gateway] When not using the DHCP function, enter the default gateway of the camera. Default: 192.168.0.1 Note: • Multiple IP addresses for the default gateway are unavailable even when using the DHCP function. Refer to the network administrator for further infor- mation about the settings of the DHCP server. [DNS] Determine how to set the address of the DNS server by selecting "Auto" (obtain the address automatically) or "Manual" (enter the address of the DNS server). When "Manual" is selected, it is necessary to configure the settings for the DNS. When using the DHCP function, it is possible to obtain the DNS address automatically by selecting "Auto". Refer to the network administrator for further informa- tion about the settings. Default: Manual [Primary server address], [Secondary server address] When "Manual" is selected for "DNS", enter the IP address of the DNS server. Refer to the network administrator about the IP address of the DNS server. ■ IPv6 network [Manual] Select "On" or "Off" to determine whether or not to manually configure the IP address for IPv6 network (IPv6 address). On: Enter an IPv6 address manually. Off: Manual entry of an IPv6 address will become unavailable. Default: Off [IP address(IPv6)] When "On" is selected for "Manual", manual entry of the IPv6 address is required. Do not enter an address already in use. Note: • When connecting to the manually configured IPv6 address beyond the router, use an IPv6 compatible router and turn on the automatic IPv6 address assignment function. In this case, it is necessary to configure IPv6 address including prefix information provided from the IPv6 compatible router. Refer to the manuals provided with the router for further information. [DHCPv6] Select "On" or "Off" to determine whether or not to use the IPv6 DHCP function. Configure the DHCP server not to assign the same IP addresses used for the other network cameras and PCs whose IP address is unique. Refer to the network administrator for further information about the settings of the server. Default: Off [Primary DNS server address], [Secondary DNS server address] Enter the IPv6 address of the DNS server. .Refer to the network administrator about the IPv6 address of the DNS server. ■ Common [HTTP port] Assign the port numbers independently. The following port numbers are unavailable since they are already in use. Available port number: 1 - 65535 Default: 80 20, 21, 23, 25, 42, 53, 67, 68, 69, 110, 123, 161, 162, 443, 554, 995, 10669, 10670, 59000 - 61000 [Line speed] Select the line speed for data transmission from the fol- lowing. It is recommended to use with the default "Auto". Auto: Line speed will be applied automatically. 100M-Full: 100 Mbps full-duplex 100M-Half: 100 Mbps half-duplex

10M-Half: 10 Mbps half-duplex Default: Auto [Max RTP packet size] Select "Unlimited(1500byte)" or "Limited(1280byte)" to determine whether or not to restrict the RTP packet size when viewing images from the camera using the RTP protocol. It is recommended to use with the default "Unlimited(1500byte)". When the RPT packet size is restricted in the network line in use, select "Limited(1280byte)".Refer to the net- work administrator for further information about the maximum packet size in the network line. Default: Unlimited(1500byte) [HTTP max segment size(MSS)] Select "Unlimited(1460byte)" or "Limited(1024byte)" to determine whether or not to restrict the maximum seg- ment size (MSS) when viewing images from the camera using the HTTP protocol. It is recommended to use with the default "Unlimited(1460byte)". When the MSS is restricted in the network line in use, select "Limited(1024byte)".Refer to the network admin- istrator for further information about the MSS in the net- work line. Default: Unlimited(1460byte) ■ UPnP This camera support UPnP (Universal Plug and Play).By using the UPnP function, it becomes possible to config- ure the following automatically. • Configuration of the port forwarding function of the router(However, a router supporting UPnP is required.) This configuration is useful when access- ing the camera via the Internet or from a cellular phone. • Automatic refreshment of the shortcut to the cam- era that is created on the "My Network Places" folder ("Network" folder when using Windows Vista or Windows 7) of the PC even when the IP address of the camera changes [Auto port forwarding] Select "On" or "Off" to determine whether or not to use the port forwarding function of the router. To use the port forwarding function, the router in use must support UPnP and the UPnP must be enabled. Default: Off Note: • Due to port forwarding, the port number may some- times be changed. When the number is changed, it is necessary to change the port numbers registered in the PC and recorders, etc. • The UPnP function is available when the camera is connected to the IPv4 network.IPv6 is not sup- ported. • To check if auto port forwarding is properly config- ured, click the [Status] tab on the "Maintenance" page, and check that the "Enable" is displayed for "Status" of "UPnP". (☞ Page 124) When "Enable" is not displayed, refer to "Cannot access the camera via the Internet." in the "Troubleshooting" section. (☞ Page 132) [Camera short cut] Select whether or not to create the shortcut to the cam- era on the "My Network Places" folder ("Network" folder when using Windows Vista or Windows 7) of the PC. When creating the shortcut, select "On". To use the shortcut function to the camera, enable the UPnP function on the PC in advance. Default: Off Note: • To display the shortcut to the camera on the "My Network Places" folder ("Network" folder when using Windows Vista or Windows 7) of the PC, it is necessary to add the Windows component. Refer to the following to enable the UPnP function. For Windows XP "Start" → "Settings" → "Control Panel" → "Add or Remove Programs" → "Add/Remove Windows Components" → select "Networking Services" → "Details"→ check "Internet Gateway Device Discovery and Control Client" and "UPnP User Interface"→ [OK]→ [Next]→ Complete For Windows Vista "Start" → "Control Panel" → "Network and Internet" → "Network and Sharing Center" → expand the section of "Network discovery" of "Sharing and Discovery" → select "Turn on network discovery" → click "Apply" → Complete For Windows 7 "Start" → "Control Panel" → "Network and Internet" → "Network and Sharing Center" → select "Turn on network discovery" of "Network discovery" of "Change advanced sharing settings" → click "Save changes" → Complete

encrypting the access to cameras using the HTTPS function. Refer to page 99 for how to configure the HTTPS set- tings. [CRT key generate] CRT key (SSL encryption key) used for the HTTPS pro- tocol is generated. To generate the CRT key, click the [Execute] button to display "CRT key generate" dialog box. [Self-signed Certificate - Generate] The camera itself generates the security certificate used for the HTTPS protocol. (Self-signed certificate) To generate the self-signed certificate, click the [Execute] button to display the "Self-signed Certificate - Generate" dialog box. [Self-signed Certificate - Information] Displays the information of the self-signed certificate. When the [Confirm] button is clicked, the registered information of the self-signed certificate will be dis- played in the "Self-signed Certificate - Confirm" dialog box. When the [Delete] button is clicked, the generated self- signed certificate will be deleted. [CA Certificate - Generate Certificate Signing Request] When using the security certificate issued by CA (Certificate Authority) as the security certificate used for the HTTPS protocol, the CSR (Certificate Signing Request) will be generated. To generate the CSR, click the [Execute] button to dis- play the "CA Certificate - Generate Certificate Signing Request" dialog window. [CA Certificate - CA Certificate install] Installs the server certificate (security certificate) issued by CA (Certificate Authority) and displays the informa- tion of the installed server certificate. To install the server certificate, click the [Browse...] but- ton to display the Open dialog box, and select the file of the server certificate issued by CA, and click the [Execute] button. If the server certificate is already installed, the file name of the installed server certificate will be displayed. [CA Certificate - Information] Displays the information of the server certificate. When the [Confirm] button is clicked, the registered information of the installed server certificate will be dis- played in the "CA Certificate - Confirm" dialog box. If the server certificate is not installed, the content of the generated CSR file will be displayed. When the [Delete] button is clicked, the installed server certificate will be deleted. Important: • Before deleting the valid server certificate (security certificate), confirm that there is a backup file on the PC or another media. The backup file will be required when installing the server certificate again. [Connection] Select the protocol used to connect the camera. HTTP: Only the HTTP connection is available. HTTPS: Only the HTTPS connection is available. Default: HTTP [HTTPS port] Designate the HTTPS port number to be used. Available port number: 1 - 65535 Default: 443 Note: • This camera will restart after the connection setting is changed. • Notation when using the self-signed certificate If the camera is accessed using the HTTPS protocol for the first time, the warning window will be dis- played. In this case, follow the instructions of the wizard to install the self-signed certificate. (☞ Page 106) • Notation when using the server certificate In advance, install the root certificate and intermedi- ate certificate on the browser in use. Follow the instructions of CA for how to obtain and install these certificates. • When the camera is accessed using the HTTPS pro- tocol, the refresh interval and frame rate of images may be lower. • When the camera is accessed using the HTTPS pro- tocol, it may take time to display images. • When the camera is accessed using the HTTPS pro- tocol, the images may be distorted or audio may be interrupted.

varies depending on the maximum image size and transmission format. [FTP access to camera] Select "Allow" or "Forbid" to determine whether to allow or forbid the FTP access to camera. Default: Forbid [Bandwidth control(bit rate)] Select the total bit rate for data transmission from the following. Unlimited/ 64kbps/ 128kbps/ 256kbps/ 384kbps/ 512kbps/ 768kbps/ 1024kbps/ 2048kbps/ 4096kbps/ 8192kbps Default: Unlimited Note: • When selecting "64kbps", select "Off" for "Audio transmission/reception" on the [Audio] tab. (☞ Page 72) • Select "128kbps" or a faster rate to carry out the live transmission of JPEG images and the FTP peri- odic image transmission simultaneously. • When "Bandwidth control(bit rate)" is set low, taking a picture using the snap shot button may not func- tion depending on the use environment. In this case, select "QVGA" for "Image capture size" of "JPEG" on the [JPEG/H.264] (or [JPEG/MPEG-4]) tab or set "Image quality setting" of "JPEG" lower. [Easy IP Setup accommodate period] Select "20min" or "Unlimited" to determine how long the network setting operation using the Panasonic IP setting software can be allowed. 20min: The camera information display and the net- work setting operation using the Panasonic IP set- ting software are allowed for 20 minutes since the camera starts up. Unlimited: The camera information display and the net- work setting operation using the Panasonic IP set- ting software are allowed without time limitation. Default: 20min

• The port forwarding function changes a global IP address to a private IP address, and "Static IP masquerade" and "Network Address Translation (NAT)" have this function. This function is to be set in a router. • To access the camera via the Internet by connecting the camera to a router, it is necessary to assign a respec- tive HTTP port number for each camera and address translation by using the port forwarding function of the router. For further information, refer to the operating instructions of the router in use. Router Internet (WAN) Cable modem xDSL modem Address translation using the port forwarding function vvv.xxx.yyy.zzz:50000 → 192.168.0.1:50000 Address translation using the port forwarding function vvv.xxx.yyy.zzz:50001 → 192.168.0.2:50001 Private address 192.168.0.2 Port number: 50001 Private address 192.168.0.1 Port number: 50000 LAN Private address 192.168.0.254 WAN Global address vvv.xxx.yyy.zzz Enter [Global IP address + : (colon) + port number] in the "Addess" box of the browser via the Internet. vvv.xxx.yyy.zzz:50000 vvv.xxx.yyy.zzz:50001 LOCK WV-SC385 OPEN

Click the [Network] tab on the "Network" page. (☞ Pages 26 and 27: How to display/operate the setup menu) The settings relating to the HTTPS protocol that can enhance the network security by encrypting the access to cameras on this page. The HTTPS settings will be configured in the following procedure. Note: • To use the server certificate, you need to apply for the approval and the issue of server certificate by CA. • Either of the self-signed certificate or the server certificate is available. If both of them are installed, the server certificate will be used prior to the self-signed certificate. Generation of the CRT key (SSL encryption key) Configuration of the connection protocol Access to the cameras using the HTTPS protocol Application for the approval by CA (Certificate Authority) - Issue of the server certificate Generation of CSR (Certificate Signing Request) Installation of the server certificate Generation of the self-signed certificate When using the server certificate When using the self-signed certificate Generation of the CRT key (SSL encryption key) (☞ page 100) Generation of the self-signed certificate (☞ page 101) Generation of CSR (Certificate Signing Request) (☞ page 103) Installation of the server certificate (☞ page 104) Configuration of the connection protocol (☞ page 105)

Important: • When the self-signed certificate or server certificate is valid, it is impossible to generate the CRT key. • When the server certification is used, the available key size varies depending on the Caches the available key size in advance. • To generate the CRT key, it may take around 1 minute when the key size is 1024 bit and around 2 minutes when the key size is 2048 bit. Do not operate the web browser until the generation of CRT key is complete. While the CRT key is being generated, the refresh interval and line speed may be lower. Step 1 Click the [Execute] button of "CRT key generate". → The "CRT key generate" dialog box will be dis- played. Step 2 Select "1024 bit" or "2048 bit" for the length of the CRT to generate for "CRT key generate" - "RSA key size". Note: • To use the server certificate, follow the requests from the CA about the RSA key size. Step 3 Click the [Execute] button. → The generation of CRT key will be started. When the generation is finished, the key size and generation time & date of the generated key will be displayed on "Current CRT key". Note: • To change (or update) the generated CRT key, per- form Step 1 to 3. The CRT key, self-signed certifi- cate and server certification are valid in a set. When the CRT key is changed, it is necessary to re-gener- ate the self-signed certificate or re-apply for the server certificate. • When the CRT key is updated, the log of the previ- ous CRT key is saved. When the [History] button of "Current CRT key" on the "CRT key generate" dia- log box is clicked, the "Previous CRT key" dialog box will be displayed, and it is possible to check the key size and generation time & date of the previous key. When the [Apply] button is clicked on the "Previous CRT key" dialog box, it is possible to replace the current CRT key with the previous one.