Panasonic Viera TH-50VX100 Operating Instructions Manual

TH-50VX100U TH-65VX100U English Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. The illustration shown is an image.

No user-serviceable parts inside. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is in tend ed to tell the user that parts inside the product are a risk of electric shock to per sons. The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the ap pli ance. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING : To prevent damage which may result in fire or shock hazard, do not expose this apparatus to rain or mois ture. Do not place containers with water (flower vase, cups, cosmetics, etc.) above the set. (including on shelves above, etc.) WARNING : 1) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel. 2) Do not remove the grounding pin on the power plug. This apparatus is equipped with a three pin grounding-type power plug. This plug will only fit a grounding-type power outlet. This is a safety fea ture. If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the grounding plug. This video monitor is designed to display television content from a separate TV tuner. Full-power analog TV broadcasting in the United States will end (as required by law) on February 17, 2009, after which full-power TV broadcasts will be digital only. If this device is used after that date to record or display programming from a product with a TV tuner that relies on a TV antenna, that product would need to contain a digital tuner, or a TV Converter would be necessary to tune the digital signal received with a TV antenna. Analog TVs should continue to work as before for other purposes (e.g., for watching low-power TV stations still broadcasting in analog, watching pre- recorded movies, or playing video games). When a Converter is used with an older television receiver or directly with this product, a signal splitter might be necessary to continue to receive low-power analog broadcasts via an antenna. For more information, please see www.DTV.gov or 1-888-CALL-FCC. For information on the TV Converter program, and on government coupons that may be used toward the purchase of one, see www.dtv2009.gov, or call the NTIA at 1-888-DTV-2009. Please check with your cable or satellite service provider if you have questions about your cable or satellite set-top box.

1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments / accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart / apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15) To prevent electric shock, ensure the grounding pin on the AC cord power plug is securely connected.

Dear Panasonic Customer Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new Plasma Display. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt as well, and record the model number and serial number of your set in the space provided on the rear cover of these instructions. Important Safety Instructions .................................. 3 FCC STATEMENT ...................................................... 5 Safety Precautions ................................................... 6 Maintenance .............................................................. 7 Accessories .............................................................. 8 Accessories Supplied .............................................. 8 Remote Control Batteries ........................................ 8 Connections .............................................................. 9 PC Input Terminals connection .............................. 10 SERIAL Terminals connection ................................11 HDMI connection ................................................... 12 COMPONENT / RGB connection .......................... 12 Power ON / OFF ..................................................... 13 Initial selections...................................................... 14 Selecting the input signal ...................................... 14 Selecting the On-Screen Menu Language ............ 14 Basic Controls ........................................................ 15 SCROLLING BAR and TEST PATTERNS functions ..... 17 EXT. SCALER function .......................................... 17 ASPECT Controls ................................................... 18 On-Screen Menu Displays ..................................... 19 PICTURE Adjustments ........................................... 21 ADVANCED SETTINGS ........................................ 23 Picture Profiles ....................................................... 25 Saving profiles ....................................................... 26 Loading profiles ..................................................... 27 Editing profiles ....................................................... 28 Locking profiles ..................................................... 29 Adjusting POS. /SIZE ............................................. 31 SOUND Adjustment ................................................ 33 SDI SOUND OUTPUT ........................................... 33 SCREENSAVER (For preventing image retention) .. 34 Reduces screen image retention ........................... 35 SIDE BAR ADJUST ............................................... 35 Specifying the scaler.............................................. 36 Reduces power consumption ............................... 37 Customizing the On-Screen Menu Display .......... 38 SET UP for Input Signals ....................................... 39 COMPONENT / RGB IN SELECT ......................... 39 YUV / RGB IN SELECT ......................................... 39 SIGNAL menu ....................................................... 40 XGA MODE ........................................................... 40 REFRESH RATE ................................................... 40 SYNC .................................................................... 41 SDI THROUGH ..................................................... 41 Input signal display ................................................ 41 OPTIONS Adjustments ........................................... 42 Watching Videos and DVDs ................................... 43 Programming the Remote to Operate Peripheral Equipment ............................................................. 44 Troubleshooting ..................................................... 45 List of Aspect Modes ............................................. 46 Remote Control Operation / Code List ................. 47 Applicable Input Signals ........................................ 50 Specifications ......................................................... 52 Panasonic Professional Flat Panel Display Limited Warranty .. 53 LIMITED WARRANTY STATEMENT ....................... 54 Customer Service ................................................... 55

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced technician for help. This device complies with Part15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION: To assure continued compliance, follow the attached installation instructions and use only shielded interface cables when connecting to computer or peripheral devices. Any changes or modifications not expressly approved by Panasonic Corp. of North America could void the user’s authority to operate this device. FCC Declaration of Conformity Model No. TH-50VX100U, TH-65VX100U Responsible Party: Panasonic Corporation of North America One Panasonic Way 1F-10, Secaucus, NJ 07094 Contact Source: Panasonic Professional Display Company Panasonic Plasma Concierge 1-800-973-4390 CANADIAN NOTICE: This Class B digital apparatus complies with Canadian ICES-003. Note: Do not allow a still picture to be displayed for an extended period, as this can cause a permanent image retention to remain on the Plasma Display. Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode. Trademark Credits • VGA is a trademark of International Business Machines Corporation. • Macintosh is a registered trademark of Apple Computer, USA. • SVGA, XGA, SXGA and UXGA are registered trademarks of the Video Electronics Standard Association. Even if no special notation has been made of company or product trademarks, these trademarks have been fully respected. • HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. FCC STATEMENT

accessories may cause instability which could result in the possibility of injury. (All of the following accessories are manufactured by Panasonic Corporation.) CAUTION When using the Plasma Display Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display. • Top of the Plasma Display is usually very hot due to the high temperature of exhaust air being released through the ventilation holes. Burns or personal injuries can happen if any body parts are brought too close. Placing any object near the top of the display could also result in heat damages to the object as well as to the Display if its ventilation holes are blocked. Be sure to disconnect all cables before moving the Plasma Display. • Moving the Display with its cables attached might damage the cables which, in turn, can cause fire or electric shock. Disconnect the power plug from the wall outlet as a safety precaution before carrying out any cleaning. • Electric shocks can result if this is not done. Clean the power cable regularly to prevent it from becoming dusty. • Built-up dust on the power cord plug can increase humidity which might damage the insulation and cause fire. Unplug the cord from the wall outlet and clean it with a dry cloth. This Plasma Display radiates infrared rays, therefore it may affect other infrared communication equipment. Install your infrared sensor in a place away from direct or reflected light from your Plasma Display. Note: Do not allow a still picture to be displayed for an extended period, as this can cause a permanent image retention to remain on the Plasma Display. Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode. Pedestal ................................................................................ TY-ST50VX100 (for TH-50VX100U), TY-ST65VX100 (for TH-65VX100U) Wall-hanging bracket (vertical).............................................. TY-WK42PV7 (for TH-50VX100U), TY-WK65PV7 (for TH-65VX100U) Wall-hanging bracket (angled) .............................................. TY-WK42PR7 (for TH-50VX100U), TY-WK65PR8 (for TH-65VX100U) BNC Component Video Terminal Board ...............................TY-42TM6A RCA Component Video Terminal Board ................................TY-42TM6Z HD-SDI Terminal Board ........................................................TY-FB9HD HD-SDI Terminal Board with audio .......................................TY-FB10HD Dual Link HD-SDI Terminal Board ........................................TY-FB11DHD Dual HDMI Terminal Board ...................................................TY-FB10HMD DVI-D Terminal Board ...........................................................TY-FB11DD Ir Through Terminal Board ....................................................TY-FB9RT • • • • • • • • • • • Always be sure to ask a qualified technician to carry out set-up. Small parts can present choking hazard if accidentally swallowed. Keep small parts away from young children. Discard unneeded small parts and other objects, including packaging materials and plastic bags/sheets to prevent them from being played with by young children, creating the potential risk of suffocation.

WARNING The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lint-free cloth. • If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until the surface is dry. • Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise the surface may become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected. If the cabinet becomes dirty, wipe it with a soft, dry cloth. • If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth. • Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get inside the unit, operating problems may result. • Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC. Maintenance Setup Do not place the Plasma Display on sloped or unstable surfaces. • The Plasma Display may fall off or tip over. Do not place any objects on top of the Plasma Display. • If water spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result in fire or electric shock. If any foreign objects get inside the Plasma Display, please consult an Authorized Service Center. Do not cover the ventilation holes. • Doing so may cause the Plasma Display to overheat, which can cause fire or damage to the Plasma Display. Transport only in upright position! • Transporting the unit with its display panel facing upright or downward may cause damage to the internal circuitry. If using the pedestal (optional accessory), leave a space of 3 15/16” (10 cm) or more at the top, left and right, and 2 3/4” (7 cm) or more at the rear, and also keep the space between the bottom of the display and the floor surface. If using some other setting-up method, follow the manual of it. (If there is no specific indication of installation dimension in the installation manual, leave a space of 3 15/16” (10 cm) or more at the top, bottom, left and right, and 2 3/4” (7 cm) or more at the rear.) An apparatus with CLASS I construction shall be connected to a mains socket outlet with a protective earthing connection. AC Power Supply Cord The Plasma Display is designed to operate on 110 - 127 V AC, 50/60 Hz. Do not use any power supply cord other than that provided with this unit. • Doing so may cause fire or electric shocks. Securely insert the power cord plug as far as it will go. • If the plug is not fully inserted, heat may be generated which could cause fire. If the plug is damaged or the wall socket plate is loose, they should not be used. Do not handle the power cord plug with wet hands. • Doing so may cause electric shocks. Do not do anything that might damage the power cable. When disconnecting the power cable, hold the plug, not the cable. • Do not make any modifications, place heavy objects on, place near hot objects, heat, bend, twist or forcefully pull the power cable. Doing so may cause damage to the power cable which can cause fire or electric shock. If damage to the cable is suspected, have it repaired at an Authorized Service Center. If the Plasma Display will not be used for a long period of time, unplug the power cord from the wall outlet. If problems occur during use If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor is detected from the Plasma Display, unplug the power cord immediately. • Continuous use of the Display under these conditions might cause fire or permanent damage to the unit. Have the Display evaluated at an Authorized Service Center. Services to the Display by any unauthorized personnel are strongly discouraged due to its high voltage dangerous nature. If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet becomes damaged, disconnect the power cord plug immediately. • A short may occur, which could cause fire. Contact an Authorized Service Center for any repairs that need to be made.

2. Insert batteries - note correct polarity ( + and -). Precaution on battery use Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Disposal of batteries should be in an environment-friendly manner. Observe the following precautions: 1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set. 2. Do not combine a used battery with a new one. 3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”). 4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. 5. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display. 6. Do not burn or breakup batteries. Batteries must not be exposed to excessive heat such as sunshine, fire or the like. 7. Make a note of the remote control codes before changing batteries in case the codes are reset. (see page 44) Accessories Supplied Check that you have the Accessories and items shown Operating Instruction book Remote Control Transmitter N2QAYB000323 Batteries for the Remote Control Transmitter (2 × AA Size) AC cord Fixing band × 1 Remote Control Batteries Helpful Hint: For frequent remote control users, replace old batteries with Alkaline batteries for longer life. 1. Pull and hold the hook, then open the battery cover.

Secure any excess cables with band as required. Note: Make sure that the AC cord is locked on both the left and right sides. Push until the hook clicks. 1. Keep the knob pressed. Close Open 1 Plug the AC cord into the display unit. Plug the AC cord until it clicks. 2 Fix the AC cord with the clamper which is attached to the unit. Note: One fixing band is supplied with this unit. In case of securing cables at two positions, please purchase it separately. Speaker terminal (R) Speaker terminal (L) When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation. Pass the attached cable fixing band through the clip as shown in the figure. To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure. While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band. From SERIAL Terminal on Computer (see page 11) From EXTERNAL monitor terminal on Computer (see page 10) AC cord connection (see page 13) Dual HDMI Terminals (equivalent of Dual HDMI Terminal Board (TY-FB10HMD)) (see page 12) To tighten: To loosen: Pull Pull Push the catch Note: At factory shipment, Terminal boards are installed in SLOT 1, SLOT 2 and SLOT 3. – AC cord fixing COMPONENT/RGB IN and Audio IN Terminals (equivalent of RCA Component Video Terminal Board (TY-42TM6Z)) (see page 12) Unplug the AC cord Unplug the AC cord pressing the two knobs. Note: When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet first. 2. Pull off.

Notes: Due to space limitations, occasionally you may have trouble connecting Mini D-sub 15P cable with ferrite core to PC input Terminal. With regard to the typical PC input signals that are described in the applicable input signals list (see page 50), adjustment values such as for the standard picture positions and sizes have already been stored in this unit. You can add up to eight PC input signal types that are not included in the list. Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.) The display resolution is a maximum of 1,440 × 1,080 dots when the aspect mode is set to “4:3”, and 1,920 × 1,080 dots when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity. The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection. Some PC models cannot be connected to the set. There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal. The computer shown in the illustration is for example purposes only. Additional equipment and cables shown are not supplied with this set. Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range. Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector. Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT” (when COMPONENT signal connection) or “RGB” (when RGB signal connection). (see page 39) • • • • • • • • • • • • Signal Names for Mini D-sub 15P Connector Pin Layout for PC Input Terminal COMPUTER Conversion adapter (if necessary) Mini D-sub 15p RGB PC cable Stereo plug Audio Connect a cable which matches the audio output terminal on the computer. 1 6 7 8 3 9 4 5 10 15 14 13 12 11 2 Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name 1 R (PR/CR) 6 GND (Ground) 11 NC (not connected) 2 G (Y) 7 GND (Ground) 12 SDA 3 B (PB/CB) 8 GND (Ground) 13 HD/SYNC 4 NC (not connected) 9 +5 V DC 14 VD 5 GND (Ground) 10 GND (Ground) 15 SCL Connections (Male) (Female)

Notes: Use the RS-232C straight cable to connect the computer to the Plasma Display. The computer shown is for example purposes only. Additional equipment and cables shown are not supplied with this set. The SERIAL terminal conforms to the RS-232C interface specification, so that the Plasma Display can be controlled by a computer which is connected to this terminal. The computer will require software which allows the sending and receiving of control data which satisfies the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details. • • • The SERIAL terminal is used when the Plasma Display is controlled by a computer. Basic format for control data The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent. Start (02h) 3-character command (3 bytes) Colon Parameter(s) (1 - 5 bytes) End (03h) STX C1 C2 C3 P1 P2 P3 P4 : P5 ETX Notes: If multiple commands are transmitted, be sure to wait for the response for the first command to come from this unit before sending the next command. If an incorrect command is sent by mistake, this unit will send an “ER401” command back to the computer. SL1A, SL1B, SL2A and SL2B of Command IMS are available only when a dual input terminal board is attached. • • • Pin layout for SERIAL Terminal COMPUTER RS-232C Straight cable D-sub 9p Command Parameter Control details PON None Power ON POF None Power OFF AVL ** Volume 00 - 63 IMS None SL1 SL2 SL3 PC1 SL1A SL1B SL2A SL2B Input select (toggle) Slot1 input Slot2 input Slot3 input PC input Slot1 input (INPUT1A) Slot1 input (INPUT1B) Slot2 input (INPUT2A) Slot2 input (INPUT2B) DAM None ZOOM FULL JUST NORM SJST SNOM SFUL Screen mode select (toggle) ZOOM FULL JUST 4:3 JUST 4:3 H-FILL With the power off, this display responds to PON command only. Command Signal level RS-232C compliant Synchronization method Asynchronous Baud rate 9600 bps Parity None Character length 8 bits Stop bit 1 bit Flow control - Signal names for D-sub 9P connector Pin No. Details 2 R X D 3 T X D 5 GND 4 • 6 Non use 7 8 (Shorted in this set) 1 • 9 NC These signal names are those of computer specifications. Communication parameters (Male) (Female)

OUT PR P B Y L R COMPONENT VIDEO OUT 12 Connections COMPONENT / RGB connection Notes: Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT” (when COMPONENT signal connection) or “RGB” (when RGB signal connection). (see page 39) Additional equipment, cables and adapter plugs shown are not supplied with this set. SYNC ON G signal is needed. (see page 41) • • • Computer RGB Camcorder or DVD Example of input signal source Digital TV-SET-TOP-BOX (DTV-STB) HDMI connection This unit has terminal boards equivalent to Dual HDMI Terminal Board (TY-FB10HMD) and RCA Component Video Terminal Board (TY-42TM6Z) as standard equipment. HDMI cables DVD Player or SET-TOP-BOX (HDMI compatible machines only) [Pin assignments and signal names] 19 3 1 4 2 18 Note: Additional equipment and HDMI cables shown are not supplied with this set. Pin No. Signal Pin No. Signal 1 T.M.D.S Data2+ 11 T.M.D.S Clock Shield 2 T.M.D.S Data2 Shield 12 T.M.D.S Clock- 3 T.M.D.S Data2- 13 CEC 4 T.M.D.S Data1+ 14 Reserved (N.C. on device) 5 T.M.D.S Data1 Shield 6 T.M.D.S Data1- 15 SCL 7 T.M.D.S Data0+ 16 SDA 8 T.M.D.S Data0 Shield 17 DDC/CEC Ground 9 T.M.D.S Data0- 18 +5V Power 10 T.M.D.S Clock+ 19 Hot Plug Detect HDMI cables

Connecting the AC cord plug to the Plasma Display. Fix the AC cord plug securely to the Plasma Display with the clamper. (see page 9) Connecting the plug to the Wall Outlet. Note: When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet first. Press the Power switch on the Plasma Display to turn the set on: Power-On. Power Indicator: Green Press the button on the remote control to turn the Plasma Display off. Power Indicator: Red (standby) Press the button on the remote control to turn the Plasma Display on. Power Indicator: Green Turn the power to the Plasma Display off by pressing the switch on the unit, when the Plasma Display is on or in standby mode. Note: During operation of the power management function, the power indicator turns orange in the power off state. From the second time on, the below screen is displayed for a while (setting condition is an example). Notes: Once the language is set, this screen won’t be displayed when switching on the unit next time. After the setting, language selection can be done from the SET UP menu. (see page 14) • • When first switching on the unit Following screen will be displayed when the unit is turned on for the first time. Select the language with the remote control. Unit buttons are invalid. 1 Select the language. 2 Set.

POWER SAVE OFF OFF RGB OSD POSITION UPPER LEFT SCREENSAVER SIGNAL OSD LANGUAGE ENGLISH (US) HDMI INPUT MENU ENTER/■ MENU ENTER/■ INPUT SET UP POS. /SIZE SOUND PICTURE INPUT Press to select the input signal to be played back from the equipment which has been connected to the Plasma Display. HDMI1 HDMI2 HDMI3 HDMI4 COMPONENT PC INPUT HDMI signal terminal in SLOT1 HDMI signal terminal in SLOT2 COMPONENT or RGB signal terminal in SLOT3 PC signal terminal in PC IN Using dedicated buttons for input selection Press to select HDMI signal terminals 1–4 in SLOT 1 and 2. Press to select component or RGB signal terminal in SLOT 3. Press to select PC signal terminal in PC IN. 14 Initial selections Selecting the On-Screen Menu Language Selecting the input signal Press to display the menu screen. Press to select “SET UP”. Press to display the SET UP menu. Press to select OSD LANGUAGE. Press to select your preferred language. Select the input signals to be connected by installing the optional Terminal Boards. Notes: Selecting is also possible by pressing the INPUT button on the unit. Input terminal will not be selected if the terminal board is not installed into the SLOT. Select to match the signals from the source connected to the component/RGB input terminals. (see page 39) Image retention (image lag) may occur on the plasma display panel when a still picture is kept on the panel for an extended period. The function that darkens the screen slightly is activated to prevent image retention (see page 45), but this function is not the perfect solution to image retention. • • • • COMPO. PC INPUT CH HDMI フ DISPLAY INPUT CH HDMI フ PC COMPO. Selectable languages English(UK) Deutsch Français Italiano Español ENGLISH(US) (Japanese) Русский (Russian) SET UP menu

Enter / Aspect button (see page 18, 19) When the menu screen is displayed: “▲” : press to move the cursor up “▼” : press to move the cursor down (see page 19) INPUT button (INPUT1, INPUT2, INPUT3 and PC selection) (see page 14) Power Indicator The Power Indicator will light. • Power-OFF ... Indicator not illuminated (The unit will still consume some power as long as the power cord is still inserted into the wall outlet.) • Standby ........ Red • Power-ON ..... Green • DPMS............ Orange (With PC input signal and during operation of PC’s screensaver.) MENU Screen ON / OFF Each time the MENU button is pressed, the menu screen will switch. (see page 19)

The Plasma Display must first be plugged into the wall outlet and turned on at the power switch (see page 13). Press this button to turn the Plasma Display On, from Standby mode. Press it again to turn the Plasma Display Off to Standby mode. Remote Control Transmitter Basic Controls POS. /SIZE button (see page 31) PICTURE button (see page 21) LIGHT button Lights the INPUT and VIDEO MENU buttons for 5 seconds. Makes the selected remote control mode key (DISPLAY, VCR, DBS/CBL or DVD) flash three times. Press again to turn off the INPUT and VIDEO MENU button lights. Equipment (Remote control mode) selection buttons (see page 43, 44) MENU button Displays menu screen. (see page 19) FUNCTION button (see page 17) RETURN button (see page 19) Press the RETURN button to return to previous menu screen. POSITION buttons PC button Press to select PC input. (see page 14) OK button Press to make selections. COMPO. button Press to select COMPONENT or RGB input. (see page 14) DIRECT INPUT buttons Press the each button to select the INPUT mode. (see page 14) This button is used to switch directly to INPUT mode. VIDEO MENU button Press to select PICTURE MENU. (see page 21) MONITOR STANDARD CINEMA DYNAMIC External equipment operations (see page 43) Numeric buttons (see page 27) OFF TIMER button The Plasma Display can be preset to switch to stand-by after a fixed period. The setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer cancelled) each time the button is pressed. 30 60 0 90 When three minutes remain, “OFF TIMER 3” will flash. The off timer is cancelled if a power interruption occurs. MEM. LOAD button (see page 27) INPUT button (see page 14) ASPECT button Press to adjust the aspect. (see page 18) EXT.SCALER button (see page 17) RECALL button Press to display the current system status. 1 Input label 2 Aspect mode (see page 18) 3 Off timer The off timer indicator is displayed only when the off timer has been set. OFF TIMER 90 1 2 3 PC 4:3

Pressing activates one of the following two functions. The function button setting can be configured by accessing “Function button assign” in the OPTIONS menu. (see page 42) SCROLLING BAR TEST PATTERNS EXT. SCALER function Each time you press , an external scaler is activated or deactivated. ON EXTERNAL SCALER MODE OFF: Use the built-in scaler. ON: Use an external scaler. The setting is valid with the following signals. 1125 (1080) / 24p • 25p • 30p • 50p • 60p With input signals other than these, specifying “ON” will display the following message. ON EXTERNAL SCALER MODE Input signal must be 1125p(1080p) Note: You can also turn the built-in scaler ON and OFF by accessing “EXTERNAL SCALER MODE” in the SET UP menu. (see page 36) Press YES N O SCROLLING BAR SCROLLING BAR Press to select “YES”. Press. Activates the SCROLLING BAR ONLY screensaver. After 15 minutes, the display enters standby mode. SCROLLING BAR ONLY To exit this mode, press any button. Press YES N O TEST PATTERNS TEST PATTERNS Press to select “YES”. Press. Each time you press , a different test pattern is displayed (seven in all). Color Bars Red Green Blue Frame (2 lines × 2 dots) Black 1% window To exit this mode, press any button other than . Note: AUTO POWER OFF is deactivated during SCROLLING BAR or TEST PATTERNS operation. (see page 37)

Note: Be aware that if you put the display in a public place for commercial purposes or a public showing and then use the aspect mode select function to shrink or expand the picture, you may be violating the copyright under copyright law. It is prohibited to show or alter the copyrighted materials of other people for commercial purposes without the prior permission of the copyright holder. Press repeatedly to move through the aspect options: For details about the aspect mode, please see “List of Aspect Modes” (page 46). The aspect mode changes each time the ENTER button is pressed. [from the unit] 4:3 H-FILL ZOOM FULL JUST 4:3 ZOOM FULL For PC signal input: Notes: The aspect mode is memorized separately for each input terminal. Do not allow the picture to be displayed in 4:3 mode for an extended period, as this can cause a permanent image retention to remain on the Plasma Display Panel. • • 4:3 ZOOM JUST FULL For SD signal input (525 (480) / 60i • 60p, 625 (575) / 50i • 50p): For HD signal input [1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p • 24sF, 1250 (1080) / 50i, 750 (720) / 60p • 50p]: All Aspect mode Set “All Aspect” to “On” in OPTION menu to enable the extended aspect mode (page 42). When All Aspect mode, the aspect mode of pictures is switched as follows. For details about the aspect mode, please see “List of Aspect Modes” (page 46). For SD signal input (525 (480) / 60i • 60p, 625 (575) / 50i • 50p): 4:3 Zoom 16:9 For PC signal input: For HD signal input [1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p • 24sF, 1250 (1080) / 50i, 750 (720) / 60p • 50p]: 4:3 Zoom1 16:9 Just Zoom2 Zoom3 14:9 4:3 Full Zoom1 16:9 Just1 Zoom2 Zoom3 14:9 Just2 4:3 (1) 4:3 (2)

previous menu. 19 On-Screen Menu Displays Various menus allow you to make settings for the picture, sound, and other functions so that you can enjoy watching Display best suited for you. Remote Control Unit 1 Display the menu screen. SET UP POS. /SIZE SOUND OPTIONS PICTURE STANDARD ADVANCED SETTINGS MEMORY SAVE MEMORY LOAD MEMORY EDIT PICTURE MENU 25 0 5 NORMAL PICTURE NORMAL IZE BRIGHTNESS SHARPNESS COLOR TEMP COLOR MANAGEMENT press MENU press several times Each time the MENU button is pressed, the menu screen will switch. Normal Viewing PICTURE SET UP POS. /SIZE SOUND 2 Select the menu. SET UP POS. /SIZE SOUND OPTIONS PICTURE 1 select 2 press (Example: SOUND menu) Menus can also be accessed directly by pressing dedicated buttons, such as and . (see page 21, 31) 3 Select the item. STANDARD AUDIO MENU 0 0 0 0 1 OFF BASS NORMAL IZE MID TREBLE BALANCE SURROUND VOLUME select ENTER/■ select press (Example: SOUND menu) 4 Set. set ENTER/■ set press 5 Exit the menu. press MENU press several times

POWER SAVE STANDBY SAVE POWER MANAGEMENT AUTO POWER OFF OFF OFF ON OFF OFF RGB OSD DESIGN TYPE1 OSD POSITION UPPER LEFT OSD LANGUAGE ENGLISH (US) SCREENSAVER SIGNAL DISPLAY SIZE H-POS 0 0 0 OFF H-SIZE AUTO SETUP NORMAL IZE V-POS 0 V-SIZE 0 DOT CLOCK -16 CLOCK PHASE 1:1 PIXEL MODE OFF STANDARD AUDIO MENU 0 0 0 0 1 OFF BASS NORMAL IZE MID TREBLE BALANCE SURROUND VOLUME On Onscreen display Off All Aspect Off Studio mode Scrolling bar Function button assign Memory lock CHANNEL 1 LEFT CHANNEL SDI SOUND OUTPUT 2/2 CHANNEL 2 RIGHT CHANNEL ON SOUND OUT OFF LEVEL METER NEGATIVE IMAGE OFF OFF BRIGHT SIDE BAR ADJUST SCREENSAVER START WOBBLING PEAK LIMIT FUNCTION see page 21-30 see page 31-41 see page 31, 32 see page 33 see page 42 see page 33 see page 40, 41 see page 34, 35 0 0 0 2.2 OFF OFF OFF OFF INPUT LEVEL ADVANCED SETTINGS NORMAL IZE GAMMA AGC W/B HIGH R W/B HIGH G 0 W/B HIGH B 0 W/B LOW R 0 W/B LOW G 0 W/B LOW B 3:2 PULLDOWN STUDIO GAIN NOISE REDUCTION 0 BLACK EXTENSION see page 23, 24 20 Overview Note: Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input and menu setting. On-Screen Menu Displays 1024 ×768 XGA MODE 100 Hz REFRESH RATE SIGNAL [ COMPONENT ]

2 Select “PICTURE”. SOUND PICTURE SET UP POS. /SIZE 2 OK 1 select 3 Select the item and set. STANDARD ADVANCED SETTINGS PICTURE MENU 25 0 5 OFF NORMAL PICTURE NORMAL IZE BRIGHTNESS SHARPNESS COLOR TEMP COLOR MANAGEMENT 2 adjust or select 1 select 4 Exit the menu. or Using for menu display To display a menu for adjustment of the PICTURE menu on the bottom of the screen, press 25 PICTURE 2 adjust or select 1 select To display a menu for ADVANCED SETTINGS adjustment, press again. 0 BLACK EXTENSION To hide the menu, press or ● PICTURE MENU You can switch to the optimal picture mode for the video source and viewing environment. MONITOR STANDARD CINEMA DYNAMIC STANDARD: For viewing in standard (evening lighting) environments. This menu selects the normal levels of BRIGHTNESS and PICTURE. DYNAMIC: For viewing in brighter environments. This menu selects higher than normal levels of BRIGHTNESS and PICTURE. CINEMA: Ideal for movies. MONITOR: For use when creating broadcast or movie content. With this picture, even if the overall average picture level (APL) changes, the brightness of areas with the same signal level does not change. Notes: When “MONITOR” is selected in PICTURE MENU, the following menu items cannot be set. PICTURE menu: PICTURE SCREENSAVER menu: PEAK LIMIT (see page 35) SET UP menu: POWER SAVE (see page 37) If you would like to change the picture and color of the selected PICTURE menu to something else, adjust using the items in the PICTURE menu. (see next page) • • During “RGB” and “PC” input signal. STANDARD ADVANCED SETTINGS PICTURE MENU 25 0 5 OFF NORMAL PICTURE NORMAL IZE BRIGHTNESS SHARPNESS COLOR TEMP COLOR MANAGEMENT During “Digital” and “COMPONENT” input signal. STANDARD ADVANCED SETTINGS PICTURE MENU 25 0 5 OFF NORMAL PICTURE NORMAL IZE BRIGHTNESS SHARPNESS COLOR TEMP COLOR MANAGEMENT 6 COLOR 0 TINT

values are returned to the factory settings. Helpful Hint ( NORMALIZE Normalization) PICTURE Adjustments ● PICTURE Adjusts the proper picture contrast. Less More ● BRIGHTNESS Adjusts for easier viewing of dark pictures such as night scenes and black hair. Darker Brighter ● COLOR Adjusts color saturation. Less More ● TINT Adjusts for natural flesh tones. Reddish Greenish ● SHARPNESS Adjusts picture sharpness. Less More ● COLOR TEMP Switches to various screen color tones. NORMAL: Intermediate color temperature. COOL: Colors with a bluish tinge. STUDIO: Optimal color temperature for studio viewing (3200 K). WARM: Colors with a reddish tinge. WARM NORMAL STUDIO* COOL * “STUDIO” can be modified when “Studio mode” in the OPTIONS menu is “On”. (see page 42) ● COLOR MANAGEMENT OFF ON ON: Enables color adjustment automatically. Notes: “COLOR” and “TINT” settings cannot be adjusted for “RGB/PC” input signal. You can change the level of each function (PICTURE, BRIGHTNESS, COLOR, TINT, SHARPNESS) for each PICTURE MENU. The setting details for STANDARD, DYNAMIC and CINEMA respectively are memorized separately for each input terminal. In PICTURE, there is not a noticeable change even when contrast is increased with a bright picture or reduced with a dark picture. • • • •

Notes: The adjustment values are memorized separately for each input terminal. The adjustment range values should be used as an adjustment reference. • • ADVANCED SETTINGS PICTURE Adjustments Carry out “W/B” adjustment as follows. 1. Adjust the white balance of the bright sections using the “W/B HIGH R” , “W/B HIGH G” and “W/B HIGH B” settings. 2. Adjust the white balance of the dark sections using the “W/B LOW R” , “W/B LOW G” and “W/B LOW B” settings. 3. Repeat steps 1 and 2 to adjust. Steps 1 and 2 affect each other’s settings, so repeat each step in turn to make the adjustment. ● BLACK EXTENSION Adjusts the dark shades of the image in gradation. Less More ● INPUT LEVEL Adjustment of parts which are extremely bright and hard to see. Less More ● GAMMA Available setting values vary depending on “PICTURE MENU” settings and the type of input signal, as follows. Down Up PICTURE MENU S CURVE 1.0 2.0 2.2 2.5 2.6 STANDARD – *3 *1 DYNAMIC *3 – *1 CINEMA – *3 *2 MONITOR – *3 – *1 When 2k1k signals are received with the Dual Link HD-SDI Terminal Board (TYFB11DHD), GAMMA “2.6” can also be selected. *2 When 60 Hz signals are received, GAMMA “2.5” can also be selected. *3 When 2k1k signals are received with the Dual Link HD-SDI Terminal Board (TY-FB11DHD), GAMMA “1.0” cannot be selected. ● AGC Increases the brightness of dark signal automatically. OFF ON ● “W/B” adjustment Less More 0 0 W/B HIGH R W/B HIGH G 0 W/B HIGH B 0 W/B LOW R 0 W/B LOW G 0 W/B LOW B Adjusts the white balance for light red, light green or light blue areas. Adjusts the white balance for dark red, dark green or dark blue areas. STANDARD ADVANCED SETTINGS PICTURE MENU 25 0 5 OFF NORMAL PICTURE NORMAL IZE BRIGHTNESS SHARPNESS COLOR TEMP COLOR MANAGEMENT 0 0 0 2.2 OFF OFF OFF OFF INPUT LEVEL BLACK EXTENSION ADVANCED SETTINGS NORMAL IZE GAMMA AGC W/B HIGH R W/B HIGH G 0 W/B HIGH B 0 W/B LOW R 0 W/B LOW G 0 W/B LOW B 3:2 PULLDOWN STUDIO GAIN NOISE REDUCTION 0

“NORMALIZE”, then all adjustment values are returned to the factory settings. Helpful Hint ( NORMALIZE Normalization) ● 3:2 PULLDOWN When “ON”, the display attempts to reproduce a more natural interpretation of sources such as movie pictures, which are recorded at 24 frames per second. If the picture is not stable, turn the setting to “OFF”. OFF ON Note: When “ON”, this setting only affects the following signal input: 525i (480i), 625i (575i), 1125 (1080) / 60i signal input during “COMPONENT” input signal. • ● STUDIO GAIN Sharpens the contrast for a better view when a part of the image is too light to see. OFF ON OFF: Disables “STUDIO GAIN”. ON: Enables “STUDIO GAIN”. Notes: “STUDIO GAIN” can be modified when “Studio mode” in the OPTIONS menu is “On”. When “Studio mode” is “Off”, this setting is “OFF” and cannot be changed. (see page 42) This setting is valid only when the input signals are as follows: Component Video, RGB (analog), SDI, HDMI • • ● NOISE REDUCTION Sets the following three NR (Noise Reduction) functions together. VIDEO NR, MOSQUITO NR, BLOCK NR OFF MID MIN ADVANCED MAX [Advanced NR] Sets the three NR functions separately. 1 Select “ADVANCED”. OFF OFF ADVANCED VIDEO NR MOSQUITO NR OFF BLOCK NR NOISE REDUCTION select 2 Select the item and set. OFF OFF ADVANCED VIDEO NR MOSQUITO NR OFF BLOCK NR NOISE REDUCTION 2 set 1 select OFF MID MIN MAX VIDEO NR: Automatically reduces unwanted picture noise. MOSQUITO NR: Reduces mosquito noise around subtitles on MPEG videos. BLOCK NR: Reduces block noise when playing MPEG videos. Notes: “NOISE REDUCTION” cannot be adjusted while a PC signal is being applied. “BLOCK NR” cannot be adjusted while a HD signal is being applied. • •

in the display memory as profiles and applied as needed, for a convenient way to enjoy your preferred picture settings. Custom picture PICTURE MENU DYNAMIC 25 0 5 OFF NORMAL PICTURE NORMAL IZE BRIGHTNESS SHARPNESS COLOR TEMP COLOR MANAGEMENT ADVANCED SETTINGS MEMORY SAVE MEMORY LOAD MEMORY EDIT 6 COLOR 0 TINT STANDARD ADVANCED SETTINGS PICTURE MENU 25 0 5 OFF NORMAL PICTURE NORMAL IZE BRIGHTNESS 6 COLOR 0 TINT SHARPNESS COLOR TEMP COLOR MANAGEMENT On Memory lock Onscreen display Scrolling bar Off Off All Aspect Studio mode Function button assign STANDARD ADVANCED SETTINGS PICTURE MENU 25 0 5 OFF NORMAL PICTURE NORMAL IZE BRIGHTNESS 6 COLOR 0 TINT SHARPNESS COLOR TEMP COLOR MANAGEMENT STANDARD ADVANCED SETTINGS PICTURE MENU 0 0 0 OFF NORMAL PICTURE NORMAL IZE BRIGHTNESS 0 COLOR 0 TINT SHARPNESS COLOR TEMP COLOR MANAGEMENT Original picture Lock profiles (page 29, 30) Save the picture adjustment values in the MEMORY1 profile Save profiles Apply the MEMORY1 profile Load the profile MEMORY1 MEMORY2 MEMORY3 MEMORY4 MEMORY16 Edit the profile Delete or rename the profile Save profiles (page 26) Load profiles (page 27) Edit profiles (page 28) Locked profile My Memory MEMORY2 MEMORY3 MEMORY4 MEMORY16

Picture Profiles Saving profiles 1 Specify the picture quality in the PICTURE menu and ADVANCED SETTINGS. (see page 21-24) 2 In the PICTURE menu, select “MEMORY SAVE”. MEMORY SAVE MEMORY LOAD MEMORY EDIT 2 OK 1 select 3 Select a profile name for saving the picture adjustment values. 1. [ ] MEMORY1 MEMORY2 2. [ ] MEMORY3 3. [ 1] MEMORY4 4. [ ] MEMORY13 13. [ ] MEMORY14 14. [ ] MEMORY15 15. [ ] MEMORY16 16. [ ] MEMORY SAVE 2 OK 1 select Profiles are labeled with these icons to indicate their locked status. (see page 27) [ ], [ ]:Settings can be saved in this profile. [ ], [ ]:Settings cannot be saved in this profile. 4 Select “OK”. OK CANCEL MEMORY SAVE SAVE THE ADJUSTED VALUE IN MEMORY1 1 select 2 OK 5 Enter a name for the profile. [Entering profile names] Profile names can be up to 16 characters. To enter text, select characters in the on-screen keyboard. Edit the default profile name in the text box as desired. OK A MEMORY1█ MEMORY NAME INPUT B C D E F G H I J K L M ALL DELETE N O P Q R S T U V W X Y Z DELETE SPACE a b c d e f g h i j k l m n o p q r s t u v w x y z 0 1 2 3 4 5 6 7 8 9 ! ” # $ % & ’ + – / = ? _ ` | ~ < > ( ) [ ] { } , @ \ ˆ . ; : CANCEL 1 select 2 OK Example: Specifying “MY PICTURE” 1 Select “ALL DELETE”. MEMORY1█ All text is deleted. To delete individual characters, select “DELETE”. 2 Select “M”. M█ Repeat this process to enter the next character. 3 Select “Y”. MY█ 4 Select “SPACE”. MY █ 6 When you finished entering the profile name, select “OK”. To cancel saving the profile, select “CANCEL”. A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z 0 1 2 3 4 5 6 7 8 9 ! ” # $ % & ’ + – / = ? _ ` | ~ < > ( ) [ ] { } , @ \ ˆ . ; : OK MEMORY NAME INPUT ALL DELETE DELETE SPACE CANCEL MY PICTURE█ 1 select 2 OK

Note: Loaded profiles are stored in memory according to the selected input interface (SLOT1, 2, 3 or PC IN). 1 In the PICTURE menu, select “MEMORY LOAD”. MEMORY SAVE MEMORY LOAD MEMORY EDIT 2 OK 1 select 2 Select the profile to load. MEMORY12 12. [ 2] 1. [ ] MEMORY1 MEMORY2 2. [ 1] 2 OK 1 select Profiles are labeled with these icons to indicate their locked status. (see below) 1 Press to list the profiles. 2 Select the profile to load. MEMORY12 12. [ 2] 1. [ ] MEMORY1 MEMORY2 2. [ 1] 2 OK 1 select Profiles are labeled with these icons to indicate their locked status. (see below) To load profiles 1–9 1 Press a button in the range – . 2 Select “OK”. OK CANCEL MEMORY LOAD LOAD FROM MEMORY2 1 1 select 2 OK To load profiles 10–16 Example: To load profile 16 1 Press . The profile number is displayed in the upper-right corner of the screen. 16 2 Select “OK”. OK CANCEL MEMORY LOAD LOAD FROM MEMORY16 1 select 2 OK Lock1 Picture adjustment values are shown. Lock2 Picture adjustment values are hidden. PICTURE MENU DYNAMIC 25 0 5 OFF NORMAL PICTURE NORMAL IZE BRIGHTNESS SHARPNESS COLOR TEMP COLOR MANAGEMENT ADVANCED SETTINGS 6 COLOR 0 TINT Can be specified. Cannot be specified. PICTURE MENU DYNAMIC PICTURE NORMAL IZE BRIGHTNESS SHARPNESS COLOR TEMP COLOR MANAGEMENT ADVANCED SETTINGS COLOR TINT Can be specified. Cannot be specified. Loading profiles Loading locked profiles… In the PICTURE menu, profiles are labeled with these icons to indicate their locked status. PICTURE MENU DYNAMIC 25 0 PICTURE NORMAL IZE BRIGHTNESS :Lock1 :Lock2 Operations with locked profiles are restricted. (see page 29) Picture adjustment values in the PICTURE menu cannot be changed, except for the “PICTURE MENU”. Once you edit the “PICTURE MENU” setting, you can edit “PICTURE”, “BRIGHTNESS”, and other picture adjustment values.

Switches to “PICTURE MENU” mode display. 1 Follow steps 1–5 in the previous procedure, . 2 Select “isf Mode”. Lock1 Change password MEMORY1 Off Off MEMORY2 MEMORY12 Off isf Mode 2 set 1 select 3 Specify “On” or “Off”. 4 Exit the menu. or Specifying “On” for isf Mode changes the “PICTURE MENU” mode display as follows. “PICTURE menu” mode display STANDARD PICTURE MENU 25 0 5 PICTURE NORMAL IZE BRIGHTNESS 6 COLOR 0 TINT SHARPNESS isf Mode: Off isf Mode: On STANDARD STANDARD DYNAMIC isf Mode DAY CINEMA isf Mode NIGHT MONITOR MONITOR Mode display when is selected isf Mode: Off isf Mode: On PICTURE MENU CINEMA DYNAMIC STANDARD MONITOR PICTURE MENU isf Mode NIGHT isf Mode DAY STANDARD MONITOR

Notes: Unadjustable items are grayed out. Adjustable items differ depending on the input signal and the display mode. Adjustment details are memorized separately for different input signal formats. (Adjustments for component signals are memorized for 525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 1125 (1080) / 60i · 50i · 60p · 50p · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i, 750 (720) / 60p · 50p each, and RGB/PC/Digital signals are memorized for each frequency.) If a “Cue” or “Rew” signal from a VCR or DVD player is received, the picture position will shift up or down. This picture position movement cannot be controlled by the POS. /SIZE function. • • • ● AUTO SETUP Automatically adjust H-POS / V-POS / CLOCK PHASE / DOT CLOCK and set H-SIZE / V-SIZE the standard value when RGB signal is input. Notes: If the dot clock frequency is 162 MHz or higher, DOT CLOCK cannot be made. If the image is that the edge is hardly figured out or shadowy, that cannot be adjusted automatically. In such case, press AUTO SETUP again after changing the image to the clearer one. When DVI-D is input, CLOCK PHASE cannot be adjusted automatically. Select NORMALIZE in POS. /SIZE and press the OK button when appropriate adjustment cannot be made. • • • • ● H-POS Adjust the horizontal position. ● V-POS Adjust the vertical position. ● H-SIZE Adjust the horizontal size. ● V-SIZE Adjust the vertical size. 1 Display the menu screen. 2 Select “POS. /SIZE”. SET UP POS. /SIZE SOUND PICTURE 2 OK 1 select 3 Select the item and set. H-POS 0 0 0 H-SIZE AUTO SETUP NORMAL IZE V-POS 0 V-SIZE DISPLAY SIZE OFF 1:1 PIXEL MODE OFF 2 adjust or select 1 select 4 Exit the menu. or During “COMPONENT”, “RGB” and “PC” input signal. H-POS 0 0 0 OFF H-SIZE AUTO SETUP NORMAL IZE V-POS 0 V-SIZE 0 DOT CLOCK -16 CLOCK PHASE 1:1 PIXEL MODE OFF DISPLAY SIZE During “Digital”, “SDI” and “HDMI” input signal. H-POS 0 0 0 H-SIZE AUTO SETUP NORMAL IZE V-POS 0 V-SIZE DISPLAY SIZE OFF 1:1 PIXEL MODE OFF Using for menu display To display a menu for adjustment of the POS. /SIZE menu on the bottom of the screen, press H-POS 0 2 adjust or select 1 select the menu To hide the menu, press or

● DOT CLOCK (During “COMPONENT”, “RGB” and “PC” input signal) Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this happens, adjust so that any such noise is minimized. ● CLOCK PHASE (During “COMPONENT”, “RGB” and “PC” input signal) Eliminate the flickering and distortion. ● 1:1 PIXEL MODE Adjusts the display size when 1125i, 1125p or 1250i signal is input. Notes: Select ON when you would like to replay 1920 × 1080 input signal. Applicable input signal; 1125 (1080) / 50i · 60i · 24sF · 24p · 25p · 30p · 50p · 60p, 1250 (1080) / 50i Select OFF when flickering is shown around the image. H-SIZE, V-SIZE and DOT CLOCK cannot be adjusted when ON is selected. • • • • OFF ON ● 1:1 PIXEL MODE (2k1k) (For 2k1k signals) When the input signal is a 2k1k signal (2048×1080 / 24p, 2048×1080 / 24sF), the display size is adjusted as follows. OFF ON (LEFT) ON (CENTER) ON (RIGHT) Note: 2k1k signals can only be received when the Dual Link HD-SDI Terminal Board (TY-FB11DHD) is installed. ● DISPLAY SIZE Adjusts the image display size on screen. OFF: Sets the normal image display size on screen. ON: Sets the image display size approximately 95 % of the normal image display. OFF ON Notes: “DISPLAY SIZE” can be modified when “Studio mode” in the OPTIONS menu is “On”. When “Studio mode” is “Off”, this setting is “OFF” and cannot be changed. (see page 42) This setting is valid only when the input signals are as follows; 525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/30p, 1125/60p, 1125/50p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI) When “DISPLAY SIZE” is set to “ON”, “H-POS” and “V-POS” in “POS. /SIZE” can be adjusted. Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals. • • • • While the POS. /SIZE display is active, if the OK button is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings. Helpful Hint ( NORMALIZE Normalization)

While the “SOUND” menu is displayed, if the OK button is pressed during “NORMALIZE”, then all adjustment values are returned to the factory settings. Helpful Hint ( NORMALIZE Normalization) Item Details AUDIO MENU STANDARD: Emits the original sound. DYNAMIC: Accentuates sharp sound. CLEAR: Attenuates human voice. BASS Adjusts low pitch sounds. MID Adjusts normal sounds. TREBLE Adjusts pitch sound. BALANCE Adjusts left and right volumes. SURROUND Select ON or OFF. The benefits of surround sound are enormous. You can be completely enveloped in sound; just as if you were at a concert hall or cinema. VOLUME Adjust the sound volume level. Item Details LEFT CHANNEL CHANNEL 1 to CHANNEL 16 Selects left audio channel. RIGHT CHANNEL CHANNEL 1 to CHANNEL 16 Selects right audio channel. SOUND OUT ON OFF ON: Enables audio output. OFF: Disables audio output. LEVEL METER OFF 1-8CH 9-16CH Sets audio channels to show in the audio level meter. 8 channels are displayed in the audio level meter; 4 channels each on both right and left sides of the display. OFF: Hides the audio level meter. 1-8CH: Displays the audio level meter (1-8ch) 9-16CH: Displays the audio level meter (9-16ch) SDI SOUND OUTPUT This menu is displayed when HD-SDI Terminal Board with audio (TY-FB10HD) or Dual Link HD-SDI Terminal Board (TY-FB11DHD) is installed to the unit. Note: This menu is available only when selecting a slot that HD-SDI Terminal Board with audio (TY-FB10HD) or Dual Link HD-SDI Terminal Board (TY-FB11DHD) is installed. 1 Display the menu screen. 2 Select “SOUND” SET UP POS. /SIZE SOUND PICTURE 2 OK 1 select 3 Select the item and set. STANDARD AUDIO MENU 0 0 0 0 1 OFF BASS NORMAL IZE MID TREBLE BALANCE SURROUND VOLUME 2 adjust or select 1 select 4 Exit the menu. or CHANNEL 1 LEFT CHANNEL SDI SOUND OUTPUT 2/2 CHANNEL 2 RIGHT CHANNEL ON SOUND OUT OFF LEVEL METER

If the display must remain on, a SCREENSAVER should be used. SCREENSAVER (For preventing image retention) 1 Display the menu screen. 2 Select “SET UP”. SET UP POS. /SIZE SOUND PICTURE 2 OK 1 select 3 Select “SCREENSAVER”. COMPONENT/RGB-IN SELECT EXTERNAL SCALER MODE POWER SAVE STANDBY SAVE POWER MANAGEMENT OFF ON OFF OFF RGB SCREENSAVER SIGNAL 2 OK 1 select 4 FUNCTION selection Select “FUNCTION” and select the desired function. OFF OFF BRIGHT SIDE BAR ADJUST SCREENSAVER START WOBBLING PEAK LIMIT FUNCTION NEGATIVE IMAGE 2 change 1 select SCROLLING BAR ONLY OVERLAY SCROLLING BAR NEGATIVE IMAGE WHITE SCREEN NEGATIVE IMAGE : A negative image will be displayed on the screen. SCROLLING BAR ONLY: A white bar will scroll from left to right. The image won’t be displayed. OVERLAY SCROLLING BAR: The brightness of the image will be decreased and a white bar will scroll on it. WHITE SCREEN : The whole screen will be white. 5 START setting Select “START”. NEGATIVE IMAGE OFF OFF BRIGHT SIDE BAR ADJUST SCREENSAVER START WOBBLING PEAK LIMIT FUNCTION 1 select 2 OK The menu screen will disappear and the SCREENSAVER will be activated. To stop the SCREENSAVER under ON, press or any buttons on the main unit. Note: When the display is turned off, the SCREENSAVER will be deactivated. OFF OFF BRIGHT SIDE BAR ADJUST SCREENSAVER START WOBBLING PEAK LIMIT FUNCTION NEGATIVE IMAGE

2 Adjust the menu. OFF OFF BRIGHT SIDE BAR ADJUST SCREENSAVER START WOBBLING PEAK LIMIT FUNCTION NEGATIVE IMAGE 2 change 1 select OFF DARK MID BRIGHT 3 Exit from SCREENSAVER. or These functions prevent the occurrence of an “image retention” on the display when turned ON. WOBBLING: Automatically shifts the display image (therefore unnoticeable to the eye) to prevent image retention of sharper contour of image. ON1: Shifts the image every 30 seconds. ON2: Shifts the image at a dot level pitch depending on screen-detection. PEAK LIMIT: Suppresses image contrast (peak brightness). Note: When a still picture is viewed for an extended time, the screen may become slightly darker. (see page 45) Reduces screen image retention SIDE BAR ADJUST Do not display a picture in 4:3 mode for an extended period, as this can cause an image retention to remain on the side bars on either side of the display field. To reduce the risk of such an image retention, illuminate the side bars. This function may be applicable to the non-picture area. Notes: To reduce the occurrence of image retention, set the “SIDE BAR ADJUST” to “BRIGHT”. The side bar may flash (alternate black/white) depending on the picture being shown on the screen. Using Cinema mode will reduce such flashing. • • Side bars 4:3 mode Image retention SCREENSAVER (For preventing image retention) 1 Select “WOBBLING” or “PEAK LIMIT”. 2 Select “ON1”, “ON2” or “OFF” (WOBBLING). Select “ON” or “OFF” (PEAK LIMIT). OFF OFF BRIGHT SIDE BAR ADJUST SCREENSAVER START WOBBLING PEAK LIMIT FUNCTION NEGATIVE IMAGE 2 change 1 select

This menu can be used to specify whether the built-in scaler or an external scaler is used for scaler functions such as resizing and picture quality adjustment. The setting is valid with the following input signals. 1125 (1080) / 24p·25p·30p·50p·60p 1 Display the menu screen. 2 Select “SET UP”. SET UP POS. /SIZE SOUND PICTURE 2 OK 1 select 3 Select “EXTERNAL SCALER MODE” and set. COMPONENT/RGB-IN SELECT EXTERNAL SCALER MODE POWER SAVE STANDBY SAVE POWER MANAGEMENT AUTO POWER OFF OFF OFF ON OFF OFF RGB OSD DESIGN TYPE1 OSD POSITION UPPER LEFT OSD LANGUAGE ENGLISH (US) SCREENSAVER SIGNAL 2 change 1 select OFF ON OFF: Use the built-in scaler. ON: Use an external scaler. Note: Selecting “ON” in this setting deactivates the following settings and disables these operations. POS. /SIZE menu: H-SIZE, V-SIZE, 1:1 PIXEL MODE, DISPLAY SIZE (see page 31, 32) PICTURE menu: BRIGHTNESS, COLOR, TINT, SHARPNESS, MEMORY SAVE, MEMORY LOAD (see page 22, 26, 27) ADVANCED SETTINGS: 3:2 PULLDOWN, NOIZE REDUCTION (see page 24) SIGNAL menu: XGA MODE (see page 40) OPTIONS menu: All Aspect (see page 42) ASPECT Controls (see page 18) “EXT. SCALER” is displayed in the menu screen to indicate that an external scaler is in use. STANDARD EXT.SCALER PICTURE MENU 25 PICTURE NORMAL IZE BRIGHTNESS COLOR TINT 4 Exit the menu. or COMPONENT/RGB-IN SELECT EXTERNAL SCALER MODE POWER SAVE STANDBY SAVE POWER MANAGEMENT AUTO POWER OFF OFF OFF ON OFF OFF RGB OSD DESIGN TYPE1 OSD POSITION UPPER LEFT OSD LANGUAGE ENGLISH (US) SCREENSAVER SIGNAL

1 Display the menu screen. 2 Select “SET UP”. SET UP POS. /SIZE SOUND PICTURE 2 OK 1 select 3 Select the item and set. COMPONENT/RGB-IN SELECT EXTERNAL SCALER MODE POWER SAVE STANDBY SAVE POWER MANAGEMENT AUTO POWER OFF OFF OFF ON OFF OFF RGB OSD DESIGN TYPE1 OSD POSITION UPPER LEFT OSD LANGUAGE ENGLISH (US) SCREENSAVER SIGNAL 2 change 1 select 4 Exit the menu. or COMPONENT/RGB-IN SELECT EXTERNAL SCALER MODE POWER SAVE STANDBY SAVE POWER MANAGEMENT AUTO POWER OFF OFF OFF ON OFF OFF RGB OSD DESIGN TYPE1 OSD POSITION UPPER LEFT OSD LANGUAGE ENGLISH (US) SCREENSAVER SIGNAL ● POWER SAVE When this function is turned ON, luminous level of the Plasma Display is suppressed, so power consumption is reduced. ● STANDBY SAVE When this function is turned ON, power consumption of the microcomputer is reduced during power supply standby (see page 13, 15, 16), so standby power of the set is reduced. ● POWER MANAGEMENT When this function is set to ON, it operates under the following conditions to turn the power on or off automatically. When no pictures (HD/VD sync signals) are detected for 30 or so seconds during PC IN signal input: →Power is turned off (standby); the power indicator lights up orange. When pictures (HD/VD sync signals) are subsequently detected: →Power is turned on; the power indicator lights up green. Notes: • This function operates only during PC IN signal input. • This function is effective when “SYNC” is set to “AUTO” and “COMPONENT / RGB-IN SELECT” is set to “RGB”. ● AUTO POWER OFF Equipment power supply is turned OFF when there is no signal. When this is set to On, the power supply of the unit goes Off 10 minutes after the input signals stop. Note: • This function is effective for input signals except PC IN terminal.

Specify the background color and display position of on-screen menus as follows. 1 Display the menu screen. 2 Select “SET UP”. SET UP POS. /SIZE SOUND PICTURE 2 OK 1 select 3 Specify the background color. Select “OSD DESIGN” and choose the background color (transparency). STANDBY SAVE POWER MANAGEMENT AUTO POWER OFF OFF OFF ON OSD DESIGN TYPE1 OSD POSITION UPPER LEFT OSD LANGUAGE ENGLISH (US) 2 change 1 select TYPE1 TYPE2 TYPE3 4 Specify the display position. Select “OSD POSITION” and choose the display position. STANDBY SAVE POWER MANAGEMENT AUTO POWER OFF OFF OFF ON OSD DESIGN TYPE1 OSD POSITION UPPER LEFT OSD LANGUAGE ENGLISH (US) 2 change 1 select Each time you press or , the on-screen menu display position changes. Display example UPPER LEFT CENTER 5 Exit the menu. or COMPONENT/RGB-IN SELECT EXTERNAL SCALER MODE POWER SAVE STANDBY SAVE POWER MANAGEMENT AUTO POWER OFF OFF OFF ON OFF OFF RGB OSD DESIGN TYPE1 OSD POSITION UPPER LEFT OSD LANGUAGE ENGLISH (US) SCREENSAVER SIGNAL

COMPONENT / RGB IN SELECT Select to match the signals from the source connected to the COMPONENT / RGB input terminals. Y, PB, PR signals “COMPONENT” RGB signals “RGB” Notes: Selection may not be possible, depending on which optional board is installed. Make setting of the selected input terminal (SLOT1, SLOT2, SLOT3 or PC IN). • • YUV / RGB IN SELECT Select to match the signals from the source connected to the DVI input terminals. YUV signals “YUV” RGB signals “RGB” Notes: Selection may not be possible, depending on which optional board is installed. Make setting of the selected input terminal (SLOT1 or SLOT2). • • 1 Display the menu screen. 2 Select “SET UP”. SET UP POS. /SIZE SOUND PICTURE 2 OK 1 select 3 Select “COMPONENT / RGB-IN SELECT” and set. COMPONENT/RGB-IN SELECT EXTERNAL SCALER MODE POWER SAVE OFF OFF RGB SCREENSAVER SIGNAL 2 change 1 select COMPONENT RGB 4 Exit the menu. or 1 Display the menu screen. 2 Select “SET UP”. SET UP POS. /SIZE SOUND PICTURE 2 OK 1 select 3 Select “YUV / RGB-IN SELECT” and set. YUV/RGB-IN SELECT EXTERNAL SCALER MODE POWER SAVE OFF OFF RGB SCREENSAVER SIGNAL 2 change 1 select YUV RGB 4 Exit the menu. or

SET UP for Input Signals SIGNAL menu COMPONENT/RGB-IN SELECT EXTERNAL SCALER MODE POWER SAVE STANDBY SAVE POWER MANAGEMENT AUTO POWER OFF OFF OFF ON OFF OFF RGB OSD DESIGN TYPE1 OSD POSITION UPPER LEFT OSD LANGUAGE ENGLISH (US) SCREENSAVER SIGNAL For RGB AUTO SYNC 1024 ×768 33.7 kHz 60.0 Hz 1125(1080)/60i XGA MODE 100 Hz REFRESH RATE H-FREQ. V-FREQ. SIGNAL FORMAT SIGNAL [ RGB ] For COMPONENT For Digital 1024 ×768 XGA MODE 100 Hz 33.7 kHz 60.0 Hz 1125(1080)/60i REFRESH RATE H-FREQ. V-FREQ. SIGNAL FORMAT SIGNAL [ COMPONENT ] SIGNAL [ Digital ] 100 Hz REFRESH RATE 33.7 kHz 60.0 Hz 1125(1080)/60i H-FREQ. V-FREQ. 108.0 MHz DOT CLOCK-FREQ. SIGNAL FORMAT XGA MODE This menu is displayed when the input signal is analog (Component/PC). This unit supports three types of XGA signals with 60Hz vertical frequency having different aspect ratios and sampling rates (1,024 × 768 @ 60Hz, 1,280 × 768 @ 60Hz, and 1,366 × 768 @ 60Hz). Be sure to make settings in accordance with the input signal in order to achieve a more appropriate and attractive display. In addition, after making this setting, be sure to make each adjustment (such as “AUTO SETUP”) on the “POS. /SIZE” menu as necessary. (see page 30) 1024 ×768 XGA MODE 100 Hz REFRESH RATE SIGNAL [ COMPONENT ] 2 change 1 select 1024×768 1366×768 1280×768 REFRESH RATE This function sets the refresh rate of the display. This menu is displayed when the input signal is 50 Hz system (50i, 50p, 25p, 24p, 24sF) of vertical scan rate. 100 Hz: Reduce screen flicker. 50 Hz: Enhance the resolution of moving images. Note: It is recommended to set to 100 Hz normally. 1024 ×768 XGA MODE 100 Hz REFRESH RATE SIGNAL [ COMPONENT ] 2 change 1 select 100 Hz 50 Hz

Select SIGNAL from the “SET UP” menu during RGB input signal. SYNC Setting RGB sync signal Confirm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT signal) AUTO: The H and V sync or synchronized signal are automatically selected. If both input, it is selected the H and V sync. ON G: Uses a synchronized signal on the Video G signal, which is input from the G connector. VBS: Uses a synchronized signal of Composite Sync input, which is input from the HD connector. Displays the frequency and the type of the current input signal. This display is valid only for COMPONENT/RGB/PC and Digital input signal. Display range: Horizontal 15 - 110 kHz Vertical 48 - 120 Hz Input signal display The dot clock frequency is displayed during digital signal input. Set the active through function of the Dual Link HD-SDI Terminal Board (TY-FB11DHD). Note: Settings can only be performed for this menu when a slot mounted with a Dual Link HD-SDI Terminal Board (TY-FB11DHD) is selected. SDI THROUGH AUTO SYNC 1024 ×768 XGA MODE 100 Hz REFRESH RATE SIGNAL [ RGB ] 2 change 1 select AUTO VBS ON G SIGNAL [ Digital ] OFF SDI THROUGH 100 Hz REFRESH RATE 2 change 1 select ON OFF ON: Enables active through. OFF: Disables active through.

• Power on display • Input signal switch display • No signal display • Mute after was pressed. Off: Hides all the items above from view. All Aspect Sets All Aspect mode (advanced aspect setting) or default aspect mode. With each press of button, the aspect changes in the selected mode. Off: Default aspect mode On: All Aspect mode Aspect mode of each setting is as follows: (Example: HD signal) Off 4:3→H-FILL→ZOOM→FULL→JUST On 4:3 (1)→4:3 (2)→4:3 Full→Zoom1→Zoom2→Zoom3→16:9→14:9→Just1→Just2 Studio mode For switching functions in setting menus used for television studio applications. Studio mode: On Studio mode: Off COLOR TEMP “STUDIO” can be selected. “STUDIO” not available. STUDIO GAIN Can be switched ON and OFF. Cannot be specified (set to “OFF” and cannot be changed). DISPLAY SIZE Can be switched ON and OFF. Cannot be specified (set to “OFF” and cannot be changed). Function button assign Specifies the function activated when the button on the remote control is pressed. Scrolling bar: Activates the SCROLLING BAR ONLY screensaver. After 15 minutes, the display enters standby mode. Test patterns:Each time you press , a different test pattern is displayed (seven in all). Memory lock Locks or unlocks saved profiles. Also for setting passwords. (see page 29) OPTIONS Adjustments 1 Display the menu screen. 2 Select “OPTIONS”. 3 Press for more than 3 seconds. SET UP POS. /SIZE SOUND OPTIONS PICTURE 2 OK (more than 3 seconds) 1 select 4 Select the item and set. On Onscreen display Off All Aspect Off Studio mode Scrolling bar Function button assign Memory lock 2 set 1 select 5 Exit the menu. or On Onscreen display Off All Aspect Off Studio mode Scrolling bar Function button assign Memory lock

If you have applicable equipment connected to the Display, you can easily watch videos and DVDs using the Display’s remote control. You can select the external equipment to access. To operate other manufacturers’ equipment, you need to register the code for the equipment. (see page 44) 1 Select the input mode. (see page 14) HDMI1 HDMI2 HDMI3 HDMI4 COMPONENT PC INPUT INPUT 2 Select the remote control mode. Press the key to select. DISPLAY VCR DBS/CBL DVD 3 Operate the connected equipment, pointing Display’s remote control at the equipment. Example VCR MODE DVD MODE VCR Record Record – Skip Reverse/Forward Rewind/Fast Forward Reverse/Forward Stop Stop Pause Pause Play Play (For other operations, see page 47) COMPO. PC INPUT CH HDMI フ DISPLAY INPUT CH HDMI フ PC COMPO. DISPLAY

Watching Videos and DVDs 1 Connect the external equipment to the Display and Power Off the external equipment. 2 Press both buttons simultaneously for more than 3 seconds. + Release the buttons when the equipment selection buttons start flashing. 3 Select the equipment. VCR DBS/CBL DVD The selected button remains lit (other buttons are not lit). 4 Input the equipment’s 4-digit remote control code. (see page 48, 49) 5 Operate the equipment with the remote control. (see page 47) The external equipment turns On. Press to return to the Display mode. DISPLAY If the equipment does not operate with the remote control • When your equipment has a single code Input the remote control code again • When your equipment has multiple codes Change the code with 4 above and test again Note: Registration will fail if the wrong code is input or it takes more than 30 seconds to register. To find a code not listed in the code list This procedure searches all codes and is called the “sequence method.” 1 After step 3 above, change the code and test. 2 When the correct code is found. change store Operate the equipment with the remote control. (see page 47) Repeat until the code is found. It may take many attempts before the correct code is found. • • COMPO. PC INPUT CH HDMI フ DISPLAY HDMI PC DISPLAY You can operate other manufacturers’ equipment using this Display’s remote control.

Symptoms Checks Picture Sound Interference Noisy Sound Electrical Appliances Cars / Motorcycles Fluorescent light Normal Picture No Sound Volume (Check whether the mute function has been activated on the remote control.) No Picture No Sound Not plugged into AC outlet Not switched on PICTURE and BRIGHTNESS/Volume setting (Check by pressing the power switch or stand-by button on the remote control.) No Picture Normal Sound If a signal with a non-applicable color system format, or frequency is input, only the input terminal indication is displayed. No Color Normal Sound Color controls set at minimum level. (see page 21- 24) No remote control operations can be performed. Check whether the batteries have discharged completely and, if they have not, whether they were inserted properly. Check whether the remote control sensor is exposed to an outdoor light or a strong fluorescent light. Check whether the remote control designed specifically for use with the unit is being used. (The unit cannot be operated by any other remote control.) A cracking sound is sometimes heard from the unit. If there is nothing wrong with the picture or sound, this is the sound of the cabinet undergoing very slight contractions in response to changes in the room temperature. There are no adverse effects on the performance or other aspects. The top or bottom of the picture on the screen is cut off when I use the zoom function. Adjust the position of the picture on the screen. Areas at the top and bottom of the screen where the image is missing appear when I use the zoom function. When using a video software program (such as a cinema size program) with a screen wider than one in the 16:9 mode, blank areas separate from the images are formed at the top and bottom of the screen. I can hear sounds coming from inside the unit. When the power is turned on, a sound of the display panel being driven may be heard: This is normal and not indicative of malfunctioning. This Plasma Display uses special image processing. Hence a slight time lag may occur between image and audio, depending on the type of input signal. However, this is not a malfunction. Plasma Display panel Symptoms Check The screen darkens slightly when bright pictures with minimal movements are shown. The screen will darken slightly when photos, still images of a computer or other pictures with minimal movements are shown for an extended period. This is done to reduce image retention on the screen and the shortening of the screen’s service life: It is normal and not indicative of malfunctioning. It takes a while for the picture to appear. The unit digitally processes the various signals in order to reproduce esthetically pleasing images. As such, it sometimes takes a few moments for the picture to appear when the power has been turned on, when the input has been switched. The edges of the images flicker. Due to the characteristics of the system used to drive the panel, the edges may appear to flicker in the fast-moving parts of the images: This is normal and not indicative of malfunctioning. The brightness on both sides of images in 4:3 mode changes. When viewing the side panels at the “BRIGHT” or “MID” setting, the brightness on both sides may change depending on the kind of program shown: This is normal and not indicative of malfunctioning. Some parts of the screen do not light up. The plasma display panel is manufactured using an extremely high level of precision technology, however, sometimes some parts of the screen may be missing picture elements or have luminous spots. This is not a malfunction. Image retention appears Do not allow a still picture to be displayed for an extended period, as this can cause a permanent image retention to remain on the Plasma Display. Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode. Note: The permanent image retention on the Plasma Display resulting from fixed image use is not an operating defect and as such is not covered by the Warranty. This product is not designed to display fixed images for extended periods of time. Whirring sounds can be heard from the display unit. The display unit is fitted with a cooling fan to dissipate heat generated during normal use. The whirring sound is caused by rotation of the fan and is not a malfunction.

Aspect mode Picture Enlarged screen Description All Aspect: On Factory setting All Aspect: Off 16:9 FULL The display of the pictures fills the screen. In the case of SD signals, pictures with a 4:3 aspect ratio are enlarged horizontally, and displayed. This mode is suited to displaying anamorphic pictures with a 16:9 aspect ratio. 14:9 – Letterbox pictures with a 14:9 aspect ratio are enlarged vertically and horizontally so that their display fills the screen vertically and is slightly smaller than the screen horizontally. The top and bottom edges of the pictures are cut off. Side panels are displayed at the left and right edges of the screen. Just JUST Pictures with a 4:3 aspect ratio are enlarged horizontally so that the picture distortion is minimized. The display of the areas around the left and right edges of the screen is slightly elongated. Just1 Just2 JUST Pictures with a 4:3 aspect ratio are enlarged horizontally so that the picture distortion is minimized. The left and right edges of the pictures are cut off. The display of the areas around the left and right edges of the screen is slightly elongated. 4:3 4:3 Pictures with a 4:3 aspect ratio are displayed with their original aspect ratio. Side panels are displayed at the left and right edges of the screen. 4:3 (1) 4:3 (2) 4:3 Pictures with a 4:3 aspect ratio are displayed with their original aspect ratio. The left and right edges of the pictures are masked by side panels. 4:3 Full H-FILL Pictures with a 4:3 aspect ratio are enlarged horizontally so that their display fills the screen. The left and right edges of the pictures are cut off. Zoom ZOOM Letterbox pictures with a 16:9 aspect ratio are enlarged vertically and horizontally so that their display fills the screen. The top and bottom edges of the pictures are cut off. Zoom1 Zoom2 ZOOM Letterbox pictures with a 16:9 aspect ratio are enlarged vertically and horizontally so that their display fills the screen. The top and bottom edges as well as the left and right edges of the pictures are cut off. Zoom3 – Letterbox pictures with a 2.35:1 aspect ratio are enlarged vertically and horizontally so that their display fills the screen vertically and is slightly larger than the screen horizontally. The top and bottom edges as well as the left and right edges of the pictures are cut off.

The following explains how to operate external devices with the Display’s remote control. Register the remote control codes (page 44) if you want to operate an external device from another manufacturer. (see page 48, 49) Note: Operation may not be possible depending on the available memory size of the remote control. This remote control is not designed to cover operation of all functions of all models. Remote Control Operation List This chart defines which keys are operational after programming (if needed) while in the selected remote control mode, CABLE, DBS, VCR, or DVD. KEY NAME VCR MODE DBS/CBL MODE DVD MODE (DBS) (CBL) Power Power Power Power - Menu Menu Functions - PPV/VOD PPV/VOD Return - Up/Down/Left/Right Up/Down/Left/Right Up/Down/Left/Right - Select Select Enter INPUT CH Channel Up/Down Channel Up/Down Channel Up/Down Channel Up/Down – 0-9 0-9 0-9 0-9 - Page Down/Up Page Down/Up Skip Reverse/Forward TV/VCR Switch TV/DBS Switch TV/CBL Switch - Rewind/Fast Forward Rewind/Fast Forward Rewind/Fast Forward Reverse/Forward Record Record *1 Record *1 Record Stop Stop Stop Stop Pause Pause Pause Still/Pause Play Play Play Play *1: Combination type

Americast 0899 Amino 1602, 1822 Bell & Howell 0014 Bell South 0899 Clearmaster 0883 ClearMax 0883 Coolmax 0883 Digeo 1187 Digi 0637 Director 0476 Dumont 0637 General Instrument 0003, 0276, 0476, 0810 GoldStar 0144 Hamlin 0009, 0273 i3 Micro 1602 Jerrold 0003, 0012, 0014, 0276, 0476, 0810 Memorex 0000 Motorola 0276, 0476, 0810, 1106, 1187, 1254, 1376 Multitech 0883 Myrio 1602, 1822 Pace 0008, 0237, 1877 Panasonic 0000, 0107, 1786 Panther 0637 Paragon 0000 Philips 0317, 1305 Pioneer 0144, 0533, 0877, 1877 Pulsar 0000 Quasar 0000 RadioShack 0883 RCA 1256 Regal 0273, 0279 Runco 0000 Samsung 0144 Scientific Atlanta 0008, 0017, 0477, 0877, 1877 Sejin 1602 Sony 1006 Starcom 0003 Supercable 0276 Supermax 0883 Thomson 1256 Tocom 0012 Torx 0003 Toshiba 0000 Tristar 0883 V2 0883 Viewmaster 0883 Vision 0883 Vortex View 0883 Zenith 0000, 0525, 0899 AlphaStar 0772 Century 0856 Chaparral 0216 Crossdigital 1109 DirecTV 0099, 0247, 0392, 0566, 0639, 0724, 0749, 0819, 1076, 1108, 1109, 1142, 1377, 1392, 1414, 1442, 1443, 1444, 1538, 1539, 1609, 1639, 1640, 1749, 1856 Dish Network System 0775, 1005, 1170, 1171, 1505, 1775 Dishpro 0775, 1005, 1505, 1775 Echostar 0775, 1005, 1170, 1171, 1505, 1775 Expressvu 0775, 1775 GE 0566 General Instrument 0869 GOI 0775, 1775 Gradiente 0856 Hisense 1535 Hitachi 0819, 1250 HTS 0775, 1775 Hughes Network Systems 0749, 1142, 1442, 1443, 1444, 1538, 1539, 1749 Humax 1790 iLo 1535 JVC 0775, 1170, 1775 LG 1226, 1414 Magnavox 0724, 0722 Memorex 0724 Mitsubishi 0749 Motorola 0869 Next Level 0869 Panasonic 0247, 0701 Paysat 0724 Philips 0099, 0722, 0724, 0749, 0856, 1076, 1142, 1442, 1749 Proscan 0392, 0566 Proton 1535 RadioShack 0869 RCA 0566, 0855, 0143, 1392 Samsung 1108, 1109, 1276, 1377, 1442, 1609 Sony 0639, 1639, 1640 Star Choice 0869 Tivo 1142, 1442, 1443, 1444, 1538, 1539 Toshiba 0749, 0790, 1285, 1749 UltimateTV 1392, 1640 Uniden 0724, 0722 US Digital 1535 USDTV 1535 Voom 0869 Zenith 0856, 1856 DBS / CABLE (Cable Set Top Box) Brand Code Brand Code Brand Code Brand Code DBS / CABLE ( Satellite Set Top Box) Brand Code Brand Code Brand Code Brand Code ABS 1972 Admiral 0048, 0209 Adventura 0000 Aiko 0278 Aiwa 0000, 0037, 0124 Akai 0041 Alienware 1972 America Action 0278 American High 0035 Asha 0240 Audiovox 0037, 0278 Beaumark 0240 Bell & Howell 0104 Broksonic 0002, 0121, 0184, 0209, 0479, 1479 Calix 0037 Canon 0035 Carver 0081 CCE 0072, 0278 Citizen 0037, 0278, 1278 Colt 0072 Craig 0037, 0047, 0072, 0240 Curtis Mathes 0035, 0041, 0060, 0162, 1035 Cybernex 0240 CyberPower 1972 Daewoo 0045, 0278, 1278 Dell 1972 Denon 0042 DirecTV 0739, 0740, 0745, 1239, 1240 Durabrand 0038, 0039 Dynatech 0000 Electrohome 0037 Electrophonic 0037 Emerex 0032 Emerson 0000, 0002, 0037, 0043, 0121, 0184, 0209, 0278, 0479, 0593, 1278, 1479, 1593 Fisher 0047, 0104 Fuji 0033, 0035 Funai 0000, 0593, 1593 Garrard 0000 Gateway 1972 GE 0035, 0060, 0240, 0807, 1035, 1060 Go Video 0432, 0614 GoldStar 0037, 0038, 1237 Gradiente 0000 Harley Davidson 0000 Harman/Kardon 0038, 0081 Harwood 0072 Hewlett Packard 1972 HI-Q 0047 Hitachi 0000, 0041, 0042, 0089 Howard Computers 1972 HP 1972 Hughes Network Systems 0042, 0739, 0740, 0745, 1239, 1240 Humax 0739 Hush 1972 iBUYPOWER 1972 Jensen 0041 JVC 0041, 0067 KEC 0037, 0278 Kenwood 0038, 0041, 0067 KLH 0072 Kodak 0035, 0037 LG 1037 Linksys 1972 Lloyd’s 0000 Logik 0072 LXI 0037 Magnasonic 0593, 1278 Magnavox 0000, 0035, 0039, 0081, 0149, 0563, 0593, 1593, 1781 Magnin 0240 Marantz 0035, 0081 Marta 0037 Media Center PC 1972 MEI 0035 Memorex 0000, 0035, 0037, 0039, 0047, 0048, 0104, 0162, 0209, 0240, 0479, 1037, 1162, 1237, 1262 MGA 0240, 0043 MGN Technology 0240 Microsoft 1972 Mind 1972 Minolta 0042 Mitsubishi 0043, 0067, 0807 Motorola 0035, 0048 MTC 0000, 0240 Multitech 0000, 0072 NEC 0038, 0041, 0067, 0104 Nikko 0037 Niveus Media 1972 Noblex 0240 Northgate 1972 Olympus 0035 Optimus 0037, 0048, 0104, 0162, 0432, 0593, 1062, 1162, 1262 Orion 0002, 0184, 0209, 0479, 1479 Panasonic 0035, 0162, 0225, 0614, 0616, 1035, 1062, 1162, 1262 Penney 0035, 0037, 0038, 0042, 0240, 1035, 1237 Pentax 0042 Philco 0035 Philips 0035, 0081, 0618, 0739, 1081, 1181 Pilot 0037 Pioneer 0067 Polk Audio 0081 Presidian 1593 Profitronic 0240 Proscan 0060, 1060 Protec 0072 Pulsar 0039 Quasar 0035, 0162, 1035, 1162 RadioShack 0000, 1037 Radix 0037 Randex 0037 RCA 0042, 0060, 0149, 0240, 0807, 0880, 1035, 1060 Realistic 0000, 0035, 0037, 0047, 0048, 0104 ReplayTV 0614, 0616, 1615, 1616 Ricavision 1972 Runco 0039 Samsung 0045, 0240, 0739, 1014 Sanky 0039, 0048 Sansui 0000, 0041, 0067, 0209, 0479, 1479 Sanyo 0047, 0104, 0240 Scott 0043, 0045, 0121, 0184 Sears 0000, 0035, 0037, 0042, 0047, 0104, 1237 Sharp 0048, 0807, 0848 Shintom 0072 Shogun 0240 Singer 0072 Sonic Blue 0614, 0616, 1615, 1616 Sony 0000, 0032, 0033, 0035, 0636, 1032, 1232, 1972 Stack 9 1972 STS 0042 Sylvania 0000, 0035, 0043, 0081, 0593, 1593, 1781 Symphonic 0000, 0593, 1593 Systemax 1972 Tagar Systems 1972 Tatung 0041 Teac 0000, 0041 Technics 0035, 0162 Teknika 0000, 0035, 0037 Thomas 0000 Tivo 0618, 0636, 0739, 0740, 0745, 1239, 1240, 1503, 1996 TMK 0240 Toshiba 0043, 0045, 0845, 1008, 1145, 1503, 1972, 1996 Totevision 0037, 0240 Touch 1972 Unitech 0240 Vector 0045 Vector Research 0038 Video Concepts 0045 Videomagic 0037 Videosonic 0240 Viewsonic 1972 Villain 0000 Voodoo 1972 Wards 0000, 0035, 0042, 0047, 0048, 0060, 0072, 0081, 0149, 0240 White Westinghouse 0072, 0209 XR-1000 0000, 0035, 0072 Yamaha 0038 Zenith 0000, 0033, 0039, 0209, 0479, 1479 ZT Group 1972 VCR Brand Code Brand Code Brand Code Brand Code 48 Remote Control Operation / Code List Remote Control Code List

Alco 0790 Allegro 0869 Amphion Media Works 0872 Apex Digital 0672, 0717, 0755, 0794, 0796, 0797, 0830, 1004, 1020, 1056, 1061, 1100 Arrgo 1023 Aspire Digital 1168, 1407 Audiovox 0790, 1071, 1072, 1121, 1122 Axion 1071, 1072 Blaupunkt 0717 Blue Parade 0571 Broksonic 0695, 0868 Cinea 0831 CineVision 0833, 0869, 0876 Citizen 0695, 1277 Coby 0778, 0852, 1086, 1107, 1165, 1177 Craig 0831 Curtis Mathes 1087 CyberHome 0816, 0874, 1023, 1024, 1117, 1129, 1502 Daewoo 0705, 0784, 0833, 0869, 1169, 1172, 1234, 1242, 1441 Denon 0490, 0634 Desay 1407 Disney 0675, 1270 Dual 1068, 1085 Durabrand 1127 DVD2000 0521 Emerson 0591, 0675, 0821, 1268 Enterprise 0591 ESA 0821, 1268 Fisher 0670 Funai 0675, 1268, 1334 Gateway 1073, 1077, 1158, 1194 GE 0522, 0815, 0717 Go Video 0715, 0741, 0744, 0783, 0833, 0869, 1044, 1075, 1099, 1158, 1304, 1730 Go Vision 1071, 1072 GoldStar 0741 Greenhill 0717 Harman/Kardon 0582, 0702 Hitachi 0573, 0664, 1247 Hiteker 0672 Humax 1588 iLo 1348 Initial 0717 Insignia 1268 Integra 0627 JBL 0702 Jensen 1016 JSI 1423 JVC 0558, 0623, 0867, 1164 jWin 1049 Kawasaki 0790 Kenwood 0490, 0534 KLH 0717, 0790, 1020, 1149 Konka 0711, 0719, 0720 Koss 0651, 0896, 1423 Landel 0826 Lasonic 0798, 1173 Lenoxx 1127 LG 0591, 0741, 0801, 0869 LiteOn 1058, 1158, 1416, 1440 Loewe 0511, 0885 Magnavox 0503, 0539, 0646, 0675, 0821, 1268 Malata 0782, 1159 Marantz 0539 Memorex 0695, 0831, 1270 Microsoft 0522, 1708 Mintek 0717, 0839 Mitsubishi 0521, 1521 Momitsu 1082 NAD 0741 NEC 0785 Nesa 0717 Next Base 0826 NexxTech 1402 Norcent 0872, 1003, 1107, 1265 Onkyo 0503, 0627, 0792 OptoMedia Electronics 0896 Oritron 0651 Panasonic 0490, 0703, 1362, 1462, 1490, 1762, 1779, 2060, 2061, 2062 Philips 0503, 0539, 0646, 0675, 0854, 1260, 1267, 1354 Pioneer 0525, 0571, 0631 Polaroid 1020, 1061, 1086 Polk Audio 0539 Portland 0770 Presidian 0675, 1072 Prima 1016 Proscan 0522 ProVision 0778 Qwestar 0651 RCA 0522, 0571, 0717, 0790, 0822, 1022, 1132, 1769 Rio 0869 Rotel 0623 Rowa 0823 Sampo 0698, 0752 Samsung 0199, 0490, 0573, 0820, 0899, 1044, 1075 Sansui 0695 Sanyo 0670, 0695, 0873 Sensory Science 1158 Sharp 0630, 0675, 0752, 1256 Sharper Image 1117 Sherwood 0633, 0770, 1043, 1077 Shinsonic 0533, 0839 Sonic Blue 0869, 1099 Sony 0533, 0864, 1033, 1070, 1431, 1533 Sova 1122 Superscan 0821 SVA 0860, 1105 Sylvania 0675, 0821, 1268 Symphonic 0675, 0821 Teac 0790 Technics 0490, 0703 Technosonic 0730 Theta Digital 0571 Toshiba 0503, 0695, 1045, 1154, 1588, 1769 Tredex 0800 Urban Concepts 0503 US Logic 0839 Venturer 0790 Vizio 1064, 1226 Xbox 0522, 1708 Yamaha 0490, 0539, 0545 Zenith 0503, 0591, 0741, 0869 Zoece 1265 AMW 0872 DVD Recorder / Player Brand Code Brand Code Brand Code Brand Code 49 Remote Control Operation / Code List Remote Control Code List (Continued)

Signal name Horizontal frequency (kHz) Vertical frequency (Hz) Component / RGB / Mini D-sub 15P (Dot clock (MHz)) DVI-D ∗8 (Dot clock (MHz)) 1 525 (480) / 60i 15.73 59.94 * (13.5) 2 525 (480) / 60p 31.47 59.94 * (27.0) ∗5 * (27.0) 3 625 (575) / 50i 15.63 50.00 * (13.5) 4 625 (575) / 50p 31.25 50.00 * (27.0) 5 625 (576) / 50p 31.25 50.00 * (27.0) 6 750 (720) / 60p 45.00 60.00 * (74.25) * (74.25) 7 750 (720) / 50p 37.50 50.00 * (74.25) * (74.25) 8 1,125 (1,080) / 60p 67.50 60.00 * (148.5) ∗1 * (148.5) 9 1,125 (1,080) / 60i 33.75 60.00 * (74.25) ∗1 * (74.25) 10 1,125 (1,080) / 50p 56.26 50.00 * (148.5) ∗1 * (148.5) 11 1,125 (1,080) / 50i 28.13 50.00 * (74.25) ∗1 * (74.25) 12 1,125 (1,080) / 24sF 27.00 48.00 * (74.25) ∗2 13 1,125 (1,080) / 30p 33.75 30.00 * (74.25) ∗1 * (74.25) 14 1,125 (1,080) / 25p 28.13 25.00 * (74.25) ∗1 * (74.25) 15 1,125 (1,080) / 24p 27.00 24.00 * (74.25) ∗1 * (74.25) 16 1,250 (1,080) / 50i 31.25 50.00 * (74.25) ∗3 17 2,048 × 1,080 / 24sF ∗7 27.00 48.00 18 2,048 × 1,080 / 24p ∗7 27.00 24.00 19 640 × 400 @70 Hz 31.46 70.07 * (25.17) 20 640 × 480 @60 Hz 31.47 59.94 * (25.18) ∗6 * (25.18) 21 640 × 480 @72 Hz 37.86 72.81 * (31.5) 22 640 × 480 @75 Hz 37.50 75.00 * (31.5) 23 640 × 480 @85 Hz 43.27 85.01 * (36.0) 24 800 × 600 @56 Hz 35.16 56.25 * (36.0) 25 800 × 600 @60 Hz 37.88 60.32 * (40.0) * (40.0) 26 800 × 600 @72 Hz 48.08 72.19 * (50.0) 27 800 × 600 @75 Hz 46.88 75.00 * (49.5) 28 800 × 600 @85 Hz 53.67 85.06 * (56.25) 29 852 × 480 @60 Hz 31.47 59.94 * (33.54) ∗6 * (34.24) 30 1,024 × 768 @50 Hz 39.55 50.00 * (51.89) 31 1,024 × 768 @60 Hz 48.36 60.00 * (65.0) * (65.0) 32 1,024 × 768 @70 Hz 56.48 70.07 * (75.0) 33 1,024 × 768 @75 Hz 60.02 75.03 * (78.75) 34 1,024 × 768 @85 Hz 68.68 85.00 * (94.5) 35 1,066 × 600 @60 Hz 37.64 59.94 * (53.0) * (53.0) 36 1,152 × 864 @60 Hz 53.70 60.00 * (81.62) 37 1,152 × 864 @75 Hz 67.50 75.00 * (108.0) 38 1,280 × 768 @60 Hz 47.70 60.00 * (80.14) 39 1,280 × 960 @60 Hz 60.00 60.00 * (108.0) 40 1,280 × 960 @85 Hz 85.94 85.00 * (148.5) 41 1,280 × 1,024 @60 Hz 63.98 60.02 * (108.0) * (108.0) 42 1,280 × 1,024 @75 Hz 79.98 75.03 * (135.0) 43 1,280 × 1,024 @85 Hz 91.15 85.02 * (157.5) 44 1,366 × 768 @50 Hz 39.55 50.00 * (69.92) 45 1,366 × 768 @60 Hz 48.36 60.00 * (86.71) * (87.44) 46 1,400 × 1,050 @60 Hz 65.22 60.00 * (122.61) 47 1,600 × 1,200 @60 Hz 75.00 60.00 * (162.0) * (162.0) 48 1,600 × 1,200 @65 Hz 81.25 65.00 * (175.5) 49 1,920 × 1,080 @60 Hz 67.50 60.00 * (148.5) ∗4 * (148.5) 50 1,920 × 1,200 @60 Hz 74.04 59.95 * (154.0) 51 Macintosh13” (640 × 480) 35.00 66.67 * (30.24) 52 Macintosh16” (832 × 624) 49.72 74.54 * (57.28) 53 Macintosh21” (1,152 × 870) 68.68 75.06 * (100.0) ∗1: Based on SMPTE 274M standard. ∗2: Based on SMPTE RP211 standard. ∗3: Based on SMPTE 295M standard. ∗4: The input signal is recognized as 1,125 (1,080) / 60p. ∗5: When selected the RGB format and 525p signal input to the Mini D-sub 15P terminal, it is recognized as VGA 60Hz signal. ∗6: When inputted VGA 60Hz format signal from the other than Mini D-sub 15P terminal, it is recognized as 525p signal. ∗7: Based on SMPTE 292M and 372M standards. These signals can be received when the Dual Link HD-SDI Terminal Board (TY-FB11DHD) is installed. ∗8: These signals can be received when the DVI-D Terminal Board (TY-FB11DD) is installed. Note: Signals without above specification may not be displayed properly.

Signal format Vertical frequency (Hz) Horizontal frequency (kHz) Dot clock (MHz) Number of active pixels Total number of pixels Number of active lines Total number of lines 1 VGA60 59.94 31.47 25.18 640 800 480 525 2 525/60p 59.94 31.47 27.00 720 858 480 525 3 625/50p 50.00 31.25 27.00 720 864 576 625 4 750/60p 60.00 45.00 74.25 1280 1650 720 750 5 750/50p 50.00 37.50 74.25 1280 1980 720 750 6 1125/60i 60.00 33.75 74.25 1920 2200 1080 1125 7 1125/50i 50.00 28.13 74.25 1920 2640 1080 1125 8 1125/60p 60.00 67.50 148.50 1920 2200 1080 1125 9 1125/50p 50.00 56.26 148.50 1920 2640 1080 1125 10 1125/24p 24.00 27.00 74.25 1920 2750 1080 1125 VIDEO input (HDMI) Audio signal Linear PCM : 48/44.1/32 kHz

Power Consumption Power on 605 W 755 W Stand-by condition Save OFF 0.9 W, Save ON 0.5 W Save OFF 1.0 W, Save ON 0.5 W Power off condition 0.1 W 0.2 W Plasma Display panel Drive method : AC type 50-inch, 16:9 aspect ratio Drive method : AC type 65-inch, 16:9 aspect ratio Screen size 43.5” (1,106 mm) (W) × 24.4” (622 mm) (H) × 49.9” (1,269 mm) (diagonal) 56.4” (1,434 mm) (W) × 31.7” (807 mm) (H) × 64.7” (1,646 mm) (diagonal) (No.of pixels) 2,073,600 (1,920 (W) × 1,080 (H)) [5,760 × 1,080 dots] Operating condition Temperature 32 °F - 104 °F (0 °C - 40 °C) Humidity 20 % - 80 % Applicable signals Scanning format 525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 750 (720) / 60p · 50p, 1125 (1080) / 60i · 60p · 50i · 50p · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i PC signals VGA, SVGA, XGA, SXGA UXGA ···· (compressed) Horizontal scanning frequency 15 - 110 kHz Vertical scanning frequency 48 - 120 Hz Connection terminals HDMI A-B TYPE A Connector × 4 COMPONENT/RGB IN Y/G (RCA PIN JACK) PB/B, PR/R (RCA PIN JACK) AUDIO IN (RCA PIN JACK × 2) with sync 1.0 Vp-p (75 Ω) 0.7 Vp-p (75 Ω) 0.5 Vrms PC IN (HIGH-DENSITY MINI D-SUB 15PIN) B/PB/CB : R/PR/CR : HD/VD: AUDIO IN (M3 JACK) Y or G with sync 1.0 Vp-p (75 Ω) Y or G without sync 0.7 Vp-p (75 Ω) 0.7 Vp-p (75 Ω) 0.7 Vp-p (75 Ω) 1.0 - 5.0 Vp-p (high impedance) 0.5 Vrms SERIAL EXTERNAL CONTROL TERMINAL (D-SUB 9PIN) RS-232C COMPATIBLE Speaker terminal 6 Ω, 16 W [8 W + 8 W] (10 % THD) 8 Ω, 20 W [10 W + 10 W] (10 % THD) Accessories Supplied Remote Control Transmitter N2QAYB000323 Batteries AA Size × 2 Fixing band TMME203 × 1 Dimensions (W × H × D) 47.7” (1,210 mm) × 28.5” (724 mm) × 3.7” (93 mm) 61.2” (1,554 mm) × 36.4” (924 mm) × 3.8” (94 mm) Mass (weight) approx. 81.6 lbs approx. 152.2 lbs Note: Design and specifi cations are subject to change without notice. Mass and dimensions shown are approximate.

Unit of Panasonic Corporation of North America One Panasonic Way 1F-10 Secaucus, NJ 07094 Panasonic Professional Flat Panel Display Limited Warranty Models or Parts Part Warranty Labor Warranty Professional Flat Panel Display LIMITS AND EXCLUSIONS There are no express warranties except as listed above. THE WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING, WITHOUT LIMITION, DAMAGE TO DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THE WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may nor apply to you. This warranty gives you specific legal rights and you may other rights, which vary from state to state. If you have a problem with this product that is not handled to your satisfaction, then write the Consumer Affairs Department at the Company address indicated above. Panasonic Professional Display Company. (referred to as “the Warrantor”) will repair this product and all included accessories with new or refurbished parts, free of charge in the USA or Puerto Rico, of the original purchase in the event of a defect in materials or workmanship as follows: In the USA and Puerto Rico FOR SERVICE CALL TOLL FREE 1-800-973-4390 2 Years 2 Years On-site or carry-in service in the USA and Puerto Rico may be obtained during the warranty period by contacting Panasonic Professional Display Company Service toll free at 1-800-973-4390. This warranty is extended only to the original purchaser and is non transferable. A purchase receipt or other proof of date of original purchase will be required before warranty service is rendered. This warranty only covers failures due to defects in materials or workmanship, which occur during normal use. The warranty does not cover damage which occur in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from improper installation, set-up adjustments, improper antenna, inadequate signal pickup, maladjustment of consumer controls, improper operation, power line surge, improper voltage supply, lighting damage, or service by anyone other than an authorized repair facility, or damage that is attributable to acts of God. 53 (for the U.S.A and Puerto Rico)

5770 Ambler Drive, Mississauga, Ontario L4W 2T3 LIMITED WARRANTY STATEMENT Item Video Tape P2/SD Cards Video Heads D5 Video heads Maintenance Items Colour Camera CCD Imaging Block BT-H Series LCD Monitors * DLP™Projectors * LCD Projectors above 2,500 ANSI Lumens * LCD Projectors below 2,500 ANSI Lumens Projector Lamps 103 inch Plasma displays Hard Drive Disk Unit Parts 30 days—Replacement only (content not covered) (Content not covered) 1 year or 2,000 hrs. (prorated) Whichever comes first 1 year or 1,000 hrs. Whichever comes first 90 days 2 years 2 years 3 years or 17,000 hrs. Whichever comes first 3 years or 2,500 hrs. Whichever comes first 3 years or 1,500 hrs. Whichever comes first 50% of the rated lamp life or 1 year. Whichever comes first 3 year (burn-in not covered) 1 year plus balance (if any) of the original Manufacturer’s Limited Warranty. (Content not covered) Labour N/A N/A 1 year or 2,000 hrs. Whichever comes first 1 year or 1,000 hrs. Whichever comes first 90 days 1 year 1 year 3 years or 17,000 hrs. Whichever comes first 3 years or 2,500 hrs. Whichever comes first. 3 years or 1,500 hrs. Whichever comes first 50% of the rated lamp life or 1 year. Whichever comes first. 3 year 1 year WARRANTY COVERAGE PERIOD EXCEPTIONS Panasonic Canada Inc. (also known as PCI) warrants this product to be free of defects in material and workmanship under normal use during the applicable warranty coverage period described below. PCI agrees to repair, or at its option, exchange, any part that becomes defective. However, the product must be purchased and serviced in Canada. The product or part that shows evidence of defect must be delivered prepaid or carried in to an authorized Panasonic Broadcast Service Center. This warranty does not cover shipping costs. The warranty coverage period is one year for both parts and labour beginning with the date of original end user purchase, subject to the exceptions as stated below. Repaired or replacement parts supplied during the warranty coverage period carry the unexpired portion of the original warranty coverage period. Proof of product purchase is a condition of warranty service. The owner must produce the product purchase receipt or other satisfactory evidence of date of original purchase. This warranty does not apply to external appearance items, such as handles, knobs, safety windows, etc. This warranty does not apply to any part, or parts, of the product, installed, altered, repaired or misused in any way that, in the opinion of PCI, affects the reliability of or detracts from the performance of the product. For products requiring routine preventive maintenance, that maintenance must be performed in order to maintain warranty coverage. Serial numbers that have been altered, defaced or removed void this warranty. This warranty does not cover replacements or repairs necessitated by loss or damage resulting from any cause beyond the control of PCI. Marking or retained images (sometimes called “burn-in”) resulting from the display of fixed images on video display products are not defects and are not covered under this warranty. In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the exclusion of implied warranties, so the above limitations and exclusions may not be applicable. Warranty Service If the product needs to be shipped for service, carefully pack (preferably in the original carton) and enclose a letter, detailing the complaint. Send prepaid and adequately insured to the local authorized Panasonic Service Centre in your area or to Panasonic Technical Support and Product Services Department, 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3. Shipping to the latter location requires a return authorization before shipment. No liability is assumed for loss or damage to the product while in transit. THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES. • Dust, smoke, rental/staging environment and twenty-four/seven operation, dramatically decreases the interval between performances of routine preventive maintenance required to maintain this warranty coverage. 54 (for Canada)

Unit of Panasonic Corporation of North America Executive Office : One Panasonic Way 1F-10, Secaucus, NJ 07094 EASTERN ZONE : One Panasonic Way 4E-7 Secaucus, NJ 07094 (201) 348-7621 Mid-Atlantic/New England : One Panasonic Way 4E-7 Secaucus, NJ 07094 (201) 348-7621 Southeast Region : 1225 Northbrook Parkway, Ste 1-160 Suwanee GA 30024 (770)338-6835 Central Region : 1707 N Randall Road E1-C-1, Elgin, IL 60123 (847)468-5200 WESTERN ZONE : 3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500 Dallas Region : 6226 Abington Way, Houston, TX 77008 (713) 802-2726 No. CA/Northwest Region : 5870 Stone Ridge, #3, Pleasanton, CA (925) 416-5108 Government Marketing Department : 52 West Gude Drive, Rockville, MD 20850 (301) 738-3840 Panasonic Canada Inc. 5770 Ambler Drive Mississauga, Ontario L4W 2T3 Customer’s Record The model number and serial number of this product can be found on its back cover. You should note this serial number in the space provided below and retain this book, plus your purchase receipt, as a permanent record of your purchase to aid in identification in the event of theft or loss, and for Warranty Service purposes. Model Number Serial Number © Panasonic Corporation 2008 Printed in Japan PBS1108S1128