Payne PH1Z024 Installation Instructions Manual

File Specifications

Brand: Payne
Category: Heat Pump
Model: PH1Z024 (Installation Instructions Manual), pr3ddN6tMdGXA
File Type: PDF
File Size: 4.17 Mb
Pages: 28 pages

Download PDF

Download Payne PH1Z024 Manual (28 pages)

Read Online:

Read the Payne PH1Z024 Installation Instructions Manual online using the built-in PDF viewer.

Key Pages of Document

Read the entire instrt/ction manual before starting the installation.

TABLE OF CONTENTS SAFETY ( ONSIDERATIONS 2 INTRODUCTION 2 RECEIVrNG AND INSTALLATION ................................................................................................................................... ...

tnit Top Removal

(Outdooro(oilSide) 19 [ndool Blowel and Motor 19 Outdoor (oil, Indoor (oil, and Condensate Drain Pan 20 Outdoor Fan .......................................................................................................... 21 Electrical Controls and Wiring ......................................................... ...

TOP OF UNIT .........................................................................................

0 DUCT SiDE OF UNIT ............................................. ...

DUCT ©PES, NGS

REQUIRED CLEARANCETO DOMgUSTIBLE MATL. INCHES [mm] TOP OF UNiT ......................................................................................... 0 DUCT StDE OF UNIT ............................................................................. 0 SIDE OPPOSI ...

DIMENSIONS IN E] ARE IN INCHES

_352.8 [1389] _3527 [1389] _537 [211] 0 o REAR VIEW 706 [27 80] r 889 [356] 12950 [5098] BOTTOMOF UNIT EVAP COND i \\X LEFT SIDE VIEW 867.0 [B4.13] 8125 [BI99] BOTTOMOF UNIT REQUIRED CLEARANCE TO COMBUSTIBLE MATL. INCHES [mml TOP OF UNIT ............................................................ ...

The unit model number and serial number are stamped on the unit identification

plate. (heck this infbm_ation against shipping papers. -Veril}' that unit voltage and amperage tisted on unit rating plate agree with power supplied tbr equipment. B. BNSPECT SHPMENT Inspect fbr shipping damage ...

4 Install2 hando%m_ed

flanges onto return air opening in holes provided to %m_ a rectangle aronnd the remm air opening 5 Install remaining 2 handoformed flanges around discharge air opening in holes provided 6. Ductwork can now be attached to flanges. When designing and installing ductwork, consider the following: L,_ CAUTION: When connecting ductwork to uni ...

If the installation

requires draining the condensate water away fi'om the unit, install a 2°in trap using a 3/4-in. OD robing or pipe. (See Fig 9 and 10.) Make sure that the outlet of the trap is at least 1 in lower than d-_eun ...

Table I -- Physical Data UNiT PHIZ 024 030 036 048 060 OPERATING WEBGNT (_bs) 232 254 277 328 368 COMPRESSOR TYPE REFRIGERANT Charge (tb) REFRBGERANT METERBNG DEVICE OUTDOOR COIL Rows...Fins/in. Face Area (sq ft) OUTDOOR-FAN MOTOR CFM Nomina_ Rpm Motor Np Diameter (in.) INDOOR COBL Rows...Fins/in. Face Area (sq ft) INDOOR FAN MOTOR B_ower Motor Size (in.) No ...

rchea erwhen snge

_n_conection isnot used Table 2--Minimum Airflow for Safe Electric Heater Operation (CFM) SIZE 036 ] 042 l 900 1050 Fig, 8--Typical installation 048 1200 1_'(25ram) MtN. TRAP 2" (50mm) MiN. Fig. 9--Condensate ...

⚠️ Download Safety

The Heat Pump Installation instructions manual (28 pages) is completely safe to download (last scan date: 03/04/2026).

Related PDF Instructions for Payne PH1Z024: