Hanna Instruments HI 110 Instruction Manual

HI 110 HI 111 HI 112 HI 113 Instruction Manual pH MR MEM SET C C RANGE GLP CFM CAL pH / ORP Meter HI 113 Select Setup Item Select pH/ORP RANGE SET Set Parameters GLP Show GLP Data MEM Store Reading MR Memory Recall Functions Confirm Calibration Point CFM Select pH Buffer / Enter/Exit Calibration CAL pH Calibra ...

defects in workmanship and materials when used for their intended purpose and maintained according to instructions. Electrodes and probes are guaranteed for six months. This warranty is limited to repair or replacement free of charge. Damage due to accidents, misuse, tampering ...

make sure that no damage has occurred during shipping. If there is any damage, notify your Dealer or the nearest Hanna Customer Service Center. Each instrument is supplied with: • HI 1131B Glass-body Combination pH Electrode with 1 m (3.3') Cable • HI 7669 ...

2) CFM/GLP key, to confirm different values or to display Good Laboratory Practice information. 3) CAL key, to enter and exit/escape calibration mode. 4) /ºC key, to manually decrease temperature value or other parameters. 5) /ºC key, to manually increase temperature value or other parameters. 6) MR key, to recall the sto ...

SPECIFICATIONS EG N AR H p 00.61 ot 00.2 – )ylno 111 IH ,PR O & ESI( V m 9.996 ± )ylno 111 IH ,PR O & ESI( V m 0002 ± Cº 0.021 ot 9.9 – N OITULO SER H p 10.0 )ylno 111 IH ,PR O & ESI( V m 1.0 )ylno 111 IH ,PR O & ESI( V m 1 Cº 1.0 YCAR UCCA F°86 / C°02 @ H p 10.0 ± )V m 9.996 ± ( V m 2.0 ± )V m 0002 ± ( V m 1 ± )rorre eborp g ...

2) CFM/GLP key, to confirm different values or to display Good Laboratory Practice information. 3) CAL key, to enter and exit/escape calibration mode. 4) /ºC key, to manually decrease temperature value or other parameters. 5) /ºC key, to manually increase temperature value or other parameters. 6) MR key, to recall the sto ...

SPECIFICATIONS EG N A R H p 0 0.6 1 ot 0 0.2 – H p 0 0 0.6 1 ot 0 0 0.2 – )ylno 3 1 1 IH ,P R O & ESI( V m 9.9 9 9 ± )ylno 3 1 1 IH ,P R O & ESI( V m 0 0 0 2 ± Cº 0.0 2 1 ot 9.9 – N OIT U LO S ER H p 1 0.0 H p 1 0 0.0 )ylno 3 1 1 IH ,P R O & ESI( V m 1.0 )ylno 3 1 1 IH ,P R O & ESI( V m 1 Cº 1.0 YCA R U CCA F°8 6 / C°0 2 @ H p 1 ...

Note: These instruments use non volatile memory to retain the pH, mV, temperature calibrations and all other settings, even when unplugged. Note: Make sure a fuse protects the main line. ELECTRODE AND PROBE CONNECTIONS For pH or ORP measurements connect an electrode wi ...

to rinse the electrode thoroughly with deionized water or tap water and then with some of the next sample to prevent cross-contamination. The pH reading is affected by temperature. In order to measure the pH accurately, the temperature effect must be compensated for. To use the ...

• Press RANGE until “rEL” message will be displayed on the secondary LCD line for about one second and “mV” tag will blink. After one second the temperature will be displayed on the secondary LCD. The reading displayed by the instrument is equal to the difference between the current mV input value and rela ...