Philips AN1651 Application Note

Text of Philips AN1651 Application Note

Using the NE/SA5234 amplifier

Author: Les Hadley 1991 Oct INTEGRATED CIRCUITS
Using the NE/SA5234 amplifier 2 1991 Oct Author: L. Hadley I. SUMMARY The NE/SA5234 is a unique low-voltage quad operational amplifier specifically designed to operate in a broadly diverse environment. It is an enhanced pin-for-pin replacement for the LM324 category of devices. Supply conditions can range from 1.8V to 6.0V with a resultant current drain of 2.8mA,-700µA per op amp. Most notable are the in
Using the NE/SA5234 amplifier 1991 Oct 3 47k 47k VIN VOUT VCC + – 5V CONVENTIONAL OP AMP PHILIPS NE5234 t t VCC VOUT VOUT VIN VIN VGND VGND VGND VCC 5V SL00569 Figure 2. Output Inversion Protection 6 5 4 3 2 1 0.5 -1 -0.1 +0.1 “N-MODE” CMRR VEE+1 < VCM < VCC “LARGE SIGNAL” CMRR “N-MODE” CMRR VEE < VCM < VEE+0.5V VEE VOS mV COMMON MODE VOLTAGE (VOLTS) NE5234 Common-Mode Operating Regions SL00631
Using the NE/SA5234 amplifier 1991 Oct 4 D2 IB2 IB4 IB5 IB6 IB8 IB7 IB9 IB3 VB4 VCC I2 I1 VEE D3 CLASS AB CONTROL Q61 Q62 Q83 Q85 Q81 Q82 Q71 Q75 Q72 Q78 Q53,54 Q51,52 C1 C2 C3 C4 C5 R82 C6 Q84 OUTPUT INPUT + – INTERMEDIATE STAGE CURRENT CONTROL CLASS AB OUTPUT R85 R76 R86 R75 SL00632 Figure 4. dB 100 80 60 40 20 0 10Hz 100Hz 1kHz 10kHz 100kHz 1MHz FREQUENCY 10  106 G1000 SL00633 Figure 5. NE5234 Closed L
Using the NE/SA5234 amplifier 1991 Oct 5 4 11 + – 47k 5234 100 x10 HP 3585 SPECTRUM ANALYZER 10Ω 600Ω +2.5V –2.5V SL00634 Figure 6. Noise Test Circuit IV. NOISE REFERRED TO THE INPUT The typical spectral voltage noise referred to each of the op amps in the NE/SA5234 is specified to be 25nV/√Hz. Current noise is not specified. In the interest of providing a balance of information on the device par
Using the NE/SA5234 amplifier 1991 Oct 6 signal-to-noise ratio at the output of this stage is determined by first multiplying the gain times the signal which gives 1VRMS with a resultant noise of 400mVRMS. The signal-to-noise ratio is calculated as S N 20log10 (1.0 4x10 4)  68dB (EQ. 5.) This is quite adequate for good quality audio applications. Next assume that the bandwidth is cut to 3.0kHz with an inp
Using the NE/SA5234 amplifier 1991 Oct 7 (EQ. 8.)  (0.163x10 3)2   4KT  100  10, 000 2   10  1.6mV (EQ. 9.) K  Boltzman sConstant  T  300oK ; BW  10kHz 1.38x10 23 Joule DegKelvin The amplified output signal = 1VRMS (EQ. 10.) S N  20 log10  1 1.6x10 3  56dB Note that there is no effect from the second-stage thermally generated resistor noise due to the dominating effect of the first-stage am
Using the NE/SA5234 amplifier 1991 Oct 8 VIII. GAIN-BANDWIDTH VS CLOSED LOOP FRE- QUENCY RESPONSE Figure 5 shows the small signal frequency response of the NE5234 versus closed-loop gain in dB. The test circuit is shown in Figure 6. The plot is taken from measured data and thus shows how each value of closed-loop gain coincides with the open-loop response curve. The NE/SA5234’s open-loop gain response h

Philips Amplifier Owners Instructions: