Speco P-30FACC Instruction Manual

Text of Speco P-30FACC Instruction Manual

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK, DO NOT OPEN COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: REMOVAL OF THE COVER SHOULD ONLY BE PER- FORMED BY QUALIFIED SERVICE PERSONNEL - NOT USER SER- VICEABLE. THE UNIT SHOULD ALWAYS BE UNPLUGGED BEFORE REMOVING THE COVER, AND REMAIN UNPLUGGED WHILE THE COVER IS REMOVED. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE UNITS NOT SPECIFICALLY DESIGNE

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.

Controls and Connections

FRONT PANEL FACC 1 3 4 5 6 7 8 9 10 11 12 2 18 19 15 16 17 14 13 AUTO-REVERSE Background Music Cassette Player EJECT PROGRAM FACD 20 1) MIC-1 input jack (1/4’’ phone jack) 11) Master volume control 2) Output level indicator 12) Power on/off switch with LED indicator 3) MIC-1 Volume control 13) Zone 4 selector switch 4) MIC-2 Volume control 14) Zone 2 select

18 19 20 21 22

23 2 FACD 1 3 5 4 6 7 8 9 10 11 13 12 14 15 16 17 18 19 20 21 22 23 2 1) Speaker outputs 13) AC 115V/230V selector switch BENEATH 2) Ground SMALL METAL COVER(SEE ABOVE). 3) FM antenna input 14) AC fuse holder 4) AM antenna input 15) LINE output RCA jacks 5) MOH output termi

1) MIC-1 input jack (1/4’’ phone jack). Accepts a balanced low impedance microphone with

a standard 1/4’’ phone plug. 2) Output level indicator. Indicates power output. Do not overload amp. 3) MIC-1 Volume control. Adjusts audio level of MIC-1. 4) MIC-2 Volume control. Adjusts audio level of MIC-2. 5) MIC-3 Volume control. Adjusts audio level of MIC-3. 6) MIC-4 Volume control. Adjusts audio level of MIC-4. 7) Line input se

8 ~ 11) Zone 1~4 output terminals. In addition to the normal 70V and 25V line outputs, there

are four groups of 70V or 25V (internally selected, see page 10) line terminals for 4 zones which can be selected using the push buttons on the front panel. 12) AC input cable receptacle . AC inlet with three pin socket for use of either 115VAC or 230VAC selected by slide switch on rear panel (see page 4). The amplifier is factory set at 115VAC main voltage. (2

CD PLAYER UNIT

1. CD display 2. Repeat button 3. Random button 4. Program button 5. CD power on/off button 6. Previous track button 7. Next track button 8. Play/pause button 9. Stop/eject button CD PLAYER OPERATION 1. Select CD mode with LINE selector switch. 2. Press POWER button on CD player. 3. Load disc (label side up) into player and PLAY begins automatically. 4. Press PAUSE button and symbol ll appears in the display and play is suspended. Press

INSERTING A CASSETTE

The cassette should be inserted edge first with the exposed tape on the right-hand side, push the cassette into the mechanism until the cassette drops into position. REMOVING THE CASSETTE Firmly press the eject button, the cassette will be automatically ejected. FAST WIND The cassette can be fast wound in either direction (forward or reverse) to any position on the tape by pressing and holdi

FCC CAUTION: To assure continued compliance, (example-use only shielded interface cables

when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. OVERCOMING GROUND LOOP PROBLEMS If the amplifier is mounted in a rack unit (Use rack mount part # PBM-RK2), or is used with equipment having its own ground, it is n

For 25V and 70V CONSTANT VOLTAGE LINE CONNECTIONS

(refer to figure 4). IMPORTANT NOTICE: When the 25V and 70V constant line voltages are used, a line matching transformer must be used with each speaker. All transformers must be connected in parallel. 70V 25V CN905 Jumper positions for 70V or 25V selection. HOW TO CONNECT LINE MATCHING TRANSFORMERS IN PARALLEL (25 VOLT LINE OR 70 VOLT LINE) ALWAYS CONNECT LINE TRANSFORMERS IN PARALLEL NEVER CONNECT LINE

Output cabling need not be shielded in most cases and should be of sufficient gauge to minimize

losses due to the resistance of the wire over long runs (insertion loss). Cable thinner than 18 gauge is not recommended. Long runs require 16 gauge or heavier. In some cases, where the output cable is run in close proximity to unshielded intercom cables, electrical cables, radio transmission antennas or other sources of interference or whe

Step 1: Fill out Wattage Tap Requirement Chart (to right)

determining the number of speakers that will be used at each wattage tap for the amplifier. Step 2: Multiple the number of speakers by each wattage tap to determine Total Wattage Requirement per Tap setting (See Ex A). Step 3: Add all the figures in shaded area to determine the total Wattage Requirement for the amplifier. Step 4: Match total Wattage Requirement to the bottom chart "Recommended Am

PA Amplifier with Music Sources

Model P - 30FACC P - 30FACD P - 60FACC P - 60FACD Supply Main Voltage AC 115V/230V ,50/60Hz ± 10% , Switchable Music Max 45W 45W 90W 90W Output power RMS Rated 30W 30W 60W 60W Outputs Speaker outputs: MOH output : ZONE outputs: 4Ω ,8Ω ,16Ω ,25V,70V 8Ω 1Watt / 600Ω ,1V balanced. 25V or 70V 4 zones + All Line out:600Ω ,1V Inputs MIC-1:250Ω ,1mV,balance

                                                                                                                                                              
                                                                                                                                                     

Speco Amplifier Owners Instructions: