Hilti TE 905-AVR Operating Instructions Manual

es Manual de instruções pt TE 905-AVR Printed: 07.07.2013 | Doc-Nr: PUB / 5071243 / 000 / 00 ...

Ce produit est certifié Este producto esta certificado Este produto está certificado C US Printed: 07.07.2013 | Doc-Nr: PUB / 5071243 / 000 / 00 ...

...

are read before the tool is operated for the first time. Always keep these operating instructions together with the tool. Ensure that the operating instructions are with the tool when it is given to other persons. ORIGINAL OPERATING INSTRUCTIONS TE905-AVR breaker 1. General information 1.1 Signal words and their meaning -CAUTION- Used to draw attention to a potentially dangerous situa- tion which could l ...

1. WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS 2. Work Area Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in explosive atmos- pheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sp ...

repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. When servicing a tool, use only identical replace- ment parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury. 3. Specific safety rules and symbols Hol ...

15 A Mains frequency 50–60 Hz Weight of tool 11.3 kg (2.5 lbs) Dimensions (l×w×h) 680×110×240 mm (26.8×4.3×9.4 in) Chuck TE-S Hammering speed under load 2200 blows/min Single impact energy 20 joules Chiseling performance in medium-hard concrete 1300 cm3/min (79.3 in3/min) Permanent lubrication Adjustable side handle Foam rubber padded grip and side handle Electronic speed ( ...

Use a vice or clamp to secure loose workpieces. -CAUTION- G The insert tool may become hot during use. G There is a risk of burning the hands. G Wear protective gloves when changing insert tools. 6.1 Adjusting the side handle  1. Unplug the supply cord from the mains socket. 2. Slacken the screw knob on the side handle. 3. Bring the side handle into the desired position. 4. Tighten the screw kn ...

Chisel jumps about. Contact pressure too high: Lower chiseling perfor- mance. Self-sharpening process Rotatethechiselinthechuck at regular intervals (ensures even wear and assists the self-sharpening process). Depth of penetration Polygon chisels break up and crush the material even at considerable depth. 6 en 60 - 100 mm 7. Care and maintenance Unplug the supply cord from the mains socket. 7.1 Care of insert tool ...

Fault in mains supply Plug in another electric appliance and check whether it works Supply cord or plug defective The cord should be checked and, if neces- sary, replaced by an electrical specialist On/off switch defective The cord should be checked and, if neces- sary, replaced by an electrical specialist No hammering action The tool is too cold Allow the tool to warm up to the minimum operating temp ...

Hilti warrants that the tool supplied is free of defects in material and workmanship. This warranty is valid so long as the tool is operated and handled correctly, cleaned and serviced properly and in accordance with the Hilti Operating Instructions, and the technical sys- tem is maintained. This means that only original Hilti consumables, components and spare parts may be used in the tool. This warranty provides ...

Right of technical and programme changes reserved S. E. & O. 376551 / G Printed: 07.07.2013 | Doc-Nr: PUB / 5071243 / 000 / 00 ...