Stanley Cara Installation And Operating Instructions Manual

Insert Stove INSTALLATION AND OPERATING INSTRUCTIONS This appliance is hot while in operation and retains its heat for a long period of time after use. Children, aged or infirm persons should be supervised at all times and should not be allowed to touch the hot working surfaces while in use or until the appliance has thoroughly cooled. When using the stove in situations where children, aged and/or infirm persons are present a fireguard must be used to prevent accidental contact with the stove. The fireguard should be manufactured in accordance with BS 8423:2002. ...

PAGE NO. 1. Insert Stove Installation & Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Fire Cement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Asbestos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Metal ...

GENERAL This insert is suitable for a standard 16” or 18” wide by 22” high fireplace opening, it is also suitable for most cast iron curved top fireplaces when used with our curved backing plate, this is available as an optional extra, see details in this manual. When installing, operating and maintaining your stove respect basic standards of fire safety. Read these instructions carefully before commencing the installation. Failure to do so may result in damage to persons or property. Consult your local Municipal office and your insurance representative to deter- mine what regulations are in for ...

baffle. It is adequate to leave them in a position where the L shaped bracket has just enough room to be removed. To remove the cast iron liners, lift them clear of the grate support plate and then move the front edge of the casting towards the middle of the stove, and clear of the back wall of the stove, then tilt the cast- ing so that it can be removed diagonally through the opening. Remove the flue spigot and gasket by removing the four bolts. Next, remove the grate by pushing it from under- neath, the riddling bar is not fixed to the grate. This will allow access to two M6 fixings which will a ...

405mm - 455mm 240mm - 320mm Min 380mm Step 2 Ensure the floor area is level with the hearth, this area needs to be level as the insert fire is screw fixed to the floor. Step 3 Lay the external casing into the opening and posi- tion it so that the front edge protrudes 20mm past the front edge of the opening. Step 4 Mark the drill locations and drill the holes using a 5.5mm drill bit. Fix the casing to the floor using the self tapping screws provided. Step 5 Lift the stove into the external casing. Remove all internal parts as per pre-assembly instructions prior to lifting it. The stove can be lifted into the casing approximately 7 ...

seal using approved fire cement between the adap- tor and the clay liner. The seal should be tapered to allow any condensation that may occur in the chimney flow back into the flue. See Fig.7. Step 5 Mark the drill locations and drill the holes using a 5.5mm drill bit. Fix the casing to the floor using the self tapping screws provided. Step 6 Lift the stove into the external casing. Remove all internal parts as per pre-assembly instructions prior to lifting it. The stove can be lifted into the casing approximately 75mm first and then it can be pushed into the final positi ...

1. Grate Support 2. Grate 3. Cast Iron Side Liners 4. Fixed Baffle 5. Loose Baffle 6. Back Bricks 7. Side Bricks 8. Fire Fence 1. Grate Support 2. Grate 4. Fixed Baffle 5. Loose Baffle 3. Cast Iron Side Liners 6. Back Bricks 7. Side Bricks 8. Fire Fence Fig 8 1. Grate Support Tilt the grate support up on one side and pass it carefully through the door opening, it should then rest on three supports approx 100mm from the floor of the stove grate. 2. Grate The grate simply lays into the grate support but care needs to be taken that the riddling bar will rest in the middle of the fork. 3. Cast Iron Side ...

REQUIREMENTS The minimum effective air requirement for this appli- ance is 8.25cm2. When calculating combustion air requirements for this appliance use the following equation: 550mm2 per each kW of rated output above 5 kW should be provided, where a flue draught stabiliser is used the total free area shall be increased by 300mm2 for each kW of rated output. If there is another appli-ance using air fitted in the same or adjacent room, it will be necessary to pro- vide an additional air supply. All materials used in the manufacture of air vents should be such that the vent is dimensionally stable, corrosion resis ...

room as the stove as this can cause the stove to emit smoke and fumes into the room. COMMISSIONING & HANDOVER On completion of the installation allow a suitable period of time for any fire cement and mortar to dry out, when a small fire may be lit and checked to ensure the smoke and fumes are taken from the stove up the chimney and emitted safely to the atmosphere. Do not run at full output for at least 24 hours. On completion of the installation and commissioning ensure that the operating instructions for the stove are left with the customer. Ensure to advise the cus- tomer on the ...

a solid, level, concrete base, a non combustible hearth conforming to current Building Regulations must extend to the front of the appliance. STOVE DIMENSIONS Fig.14 TECHNICAL DATA Nominal Output Manufactured Smokeless Fuel Room 6.5kW Typical refuelling intervals to obtain nominal outputs MSF 1.5 hours Flue Gas Mass Flow MSF 3.6 g/s Flue Gas temp at nominal output 310 oC Gross Weight: 100 kgs Flue Outlet 125 mm This appliance has been tested in accordance with BS EN 13229 485 CO ALARM Waterford Stanley strongly recommend the fitting of a CO Alarm in the same room as the app ...

ondary. The primary air control is a spin wheel locat- ed in the middle of the door. To operate the primary air control, rotate the wheel in an anti-clockwise direction to open (increase air supply) and clockwise to close (decrease air sup- ply). See Fig 15. Fig.15 Fig.16 When burning wood the primary air control should be adjusted to a maximum of one turn open after the fire has established, when wood is very well sea- soned no primary air is required, the burn rate can then be controlled using the secondary air control. Warning Leaving both air control controls fully open can lead t ...

the secondary air slide and open a few millimetres using the tool provided. Slow burning will cause the window glass to blacken and should not be used for a long period as it will leave sooty deposits in the flueways. Opening the air slide will increase the heat output and will clear the glass. To obtain slow burning when burning coal, close the secondary air fully and partially open the spin valve. DE-ASHING Never allow the ashpan to over fill as it will cause damage to the grate. Empty the ashpan before lighting. Always ensure that ashes have thoroughly cooled before removing t ...

same room as the stove as this can cause the stove to emit fumes into the room. IMPORTANT NOTES Now that your Solid Fuel stove is installed and no doubt you are looking forward to many comforts it will provide, we would like to give you some tips on how to get the best results from your stove. 1. We would like if you could take some time to read the operating instructions/hints, which we are confident, will be of great benefit to you. 2. Do not burn fuel with a high moisture content, such as a damp peat or unseasoned timber.This will only result in a build up of tar in the stove and in the chimne ...

12. For safety reasons never leave children or the elderly unaccompanied while stove is in use. Use a fireguard. 13. Avoid contact with appliance when in use as the stove reaches very high operating tempera- tures. 14. This appliance should be regularly maintained by a competent service engineer. Use only replacement parts recommended by Waterford Stanley. Using unauthorised parts will invalidate your guarantee and may cause damage or injury. AN ODOUR WILL EMIT FROM STOVE ON FIRST FIRING, WHEN FIRE REACHES MAXIMUM TEMPERATURE OVER A NUMBER OF HOURS THIS ODOUR WILL SUBSIDE. IT IS BEST ADVISED TO OPEN WI ...

should be given serious consideration: 1. The installation of smoke detectors. 2. A conveniently located fire extinguisher to con- tend with small fires resulting from burning embers. 3. A practical evacuation plan. 4. A plan to deal with a chimney fire as follows: a. Notify the fire department. b. Prepare occupants for immediate evacua- tion. c. Close all openings into the stove. d. While awaiting the fire department watch for ignition to adjacent combustibles from over head stove pipe or from embers or from sparks from the chimney. GLASS 1. How to clean: The glass will clean itself when t ...

1. SPIN VALVE - B00032AZZ 2. FIRE DOOR - B00587AZZ 3. FRONT - B00588AZZ 4. WINDOW CLIP - F00896BXX 5. DOOR CATCH - F00928AXX 6. SECONDARY AIR OP LEVER - F00993AXX 7. SECONDARY AIR CONVECTOR BAR - F00994AXX 8. SECONDARY AIR PLATE - F00995AXX 9. ASHPAN - F00997AXX 10. LEVER - F01007AXX 11. COMBUSTION CHAMBER - F01078AXX 12. CONVECTION CHAMBER - F01079AXX 13. BOTTOM BAFFLE - F01080AXX 14. LH BACK BRICK - H00203AXX 15. SIDE BRICK - H00207AXX 16. RH BACK BRICK - H00208AXX 17. MIN SPRING HANDLE - L00539AXX 18. FLUE GASKET - P00102AXX 19. 5” FLUE - Q00752AXX 20. TOP BAFFLE - Q00761AXX 21. 16” DOOR GLASS - T00098AXX 22. H ...