Stanton A.1800 Operation & User’s Manual
Text of Stanton A.1800 Operation & User’s Manual
Stanton A.1800 IMPORTANT SAFETY INSTRUCTIONS
1. Read Instructions – All the safety and operating instructions should be read before
this product is operated.
2. Retain Instructions – The safety and operating instructions should be retained for
future reference.
3. Heed Warnings – All warnings on the appliance and in the operating instructions
should be adhered to.
4. Follow Instructions – All operating and use instructions should be followed.
5. Water and Moistur
Thank you for your decision to purchase Stanton’s innovative new A Series professional power amplifier! Engineered for superior sound
reproduction, the A Series line of professional amplifiers deliver top quality audio at an affordable price. The A Series offer a standard of
reliability and efficiency that makes them the perfect solution for every DJ, musician, and sound engineer. Welcome to a new level of pro-
fessional quality sound perfor
FRONT PANEL CONTROLS
1. Rack Ears
These ears are used to mount the amplifier in any standard 19”
rack.
2. Fan Vent
The A-Series amplifiers are cooled by two rear-mounted fans
(except for A.900 which is cooled by a single rear mounted fan).
Cool air flows through the front fan filters, reducing the tempera-
ture internal components while forcing the heat out the rear vents.
Never block these vents and keep them clean at all time.
3. AC Power Switch
This s
REAR PANEL CONTROLS
1. Fan
This is a variable speed cooling fan. Cool air enters the amplifier
through the fan filters located on the front of the amplifier. Be sure
not to block these ports when installing the amplifier or other
equipment.
2. Input connectors
Connect the input source to the balanced combo connectors
using either XLR or 1/4” TRS plugs. They are configured as fol-
lows : Pin 2 (Tip) hot, Pin 3 (Ring) cold, and Pin 1 (Sleeve)
ground. We re
Stanton A.1800 Every model in the A-Series incorporates protection features. The front panel Protection LED indicates the activity of the relay speaker
connection circuitry in each channel. When the protection LED turns on, this circuitry is active, and all connected speakers are muted.
Initial power-up : For approximately five seconds after initial
power-up, the protection circuitry is activated and the speaker
outputs are muted. If everything is operating no
In stereo mode, both channels operate independently with individ-
ual input gain controls. Signal at channel 1’s input produces out-
put at channel 1, while signal at channel 2’s input produces out-
put at channel 2’s output. Recommended minimum nominal load
impedance for stereo operation is 2 ohms per channel.
Parallel Mode
When set to Parallel mode, a signal applied to channel 1’s input
will be amplified and appear at outputs for both
Bridged Mono Mode
B
B
SPK+ to PIN 1+
SPK- to PIN 1-
SPK+ to PIN 1+
SPK- to PIN 1-
SPK+ to PIN 1+
SPK- to PIN 1-
SPK+ to PIN 2+
SPK- to PIN 2-
SPK+ to PIN 1+
SPK- to PIN 1-
SPK+ to PIN 1+
SPK- to PIN 1-
SPK+ to PIN 1+
SPK- to PIN 1-
SPK+ to PIN 2+
SPK- to PIN 2-
SPK+ to PIN 1+
SPK- to PIN 2-
These are several ways to interface the amplifier to support a variety of applications.
Unbalanced 1/4” Connector
Balanced TRS 1/4” Connector
XLR Balanced Wiring Guide
Unbalanced 1/4” Connector
Rated Output Power
Stereo Both Channel Driven
8 ohms
210 W
400 W
600 W
4 ohms
320 W
600 W
900 W
2 ohms
420 W
900 W
1400 W
Rated Output Power
Bridged Mono
8 ohms
650 W
1200 W
1800 W
4 ohms
845 W
1800 W
2800 W
Signal to Noise Ratio
(20 Hz ~ 20k Hz)
100dB
102dB
104dB
Distortion (SMPTE-IM)
0.05%
0.01%
0.04%
Input sensitivity @8 ohms
4dBu
4dBu
4dBu
Voltage Gain
30dB
33dB
35dB
Output Circuitry
AB
AB
H
Current Consumption
120Vac
Stanton A.1800 The A Series of amplifiers are designed to work with many different speakers on the market. They have been paired with the following
Cerwin-Vega speakers. The following compatibility matrix can be used as a reference. (See: www.cerwin-vega.com for product specs.)
WARRANTY & RETURN POLICY
Warranty
Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the U.S., will, with-
out charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any
Stanton merchandise proved defective in material or workmanship for a period of three (3) years following the date of original purchase.
Stanton wil