Philips AZ1300/05 Operation & User’s Manual

1 x Remote Control (for AZ1305 model only) TOP AND FRONT PANEL (See 1) 1 LIFT TO OPEN - lift here to open CD door. 2 PROG CD: - programs tracks and reviews the program; Tuner: - programs preset radio stations. 3 MODE - selects different play modes: e.g. REPEAT or SHUFFLE (random) order. 4 VOLUME 3 , 4 - to adjust volume level. PRESET+ ,- (up, down) - selects a preset radio station. 5 Display - shows the status of the set. 6 2; - starts or pauses CD playback. 9 - to stop playback or erase a CD program. SEARCH ∞, § CD: - searches backward and forward within a track; - skips to the beginning of a current track/ previous/ later track. RADIO: - (down, up) tunes to radio stations. 7 DBB (Dynamic Bass Boost) - activates a more vivid bass response. 8 POWER slider - selects CD/ MW / FM / OFF function and also the power off switch (OFF). BACK PANEL (See 1) 9 Telescopic aerial - improves FM reception. 0 Battery compartment - for 6 batteries, type R-14, UM2 or C-cells. ! AC MAINS - inlet for mains lead. REMOTE CONTROL 1 VOLUME 3 , 4 - a 2 SHUFFLE - plays al 3 2; - starts or pause 4 SEARCH 5 , 6 - forwards within a tr 5 PRESET+ ,- (up, station. 6 TUNING ∞, § (d 7 9 - to stop playback - erases a CD pro 8 ¡ , ™- skips to the previous/ subseque 9 REPEAT - repeats a CAUTION Use of controls or performance of pr herein may result exposure or other POWER SUPPLY Whenever convenient, conserve battery life. M power plug from the se inserting batteries. Batteries (not includ • Insert 6 batteries, typ (preferably alkaline) • Remote control (A Insert 2 batteries, ty (preferably alkaline) English DIGITAL TUNER Tuning to radio stations 1. Adjust the POWER slider to MW or FM. ™The radio. station frequency, waveband are shown (See 3) 2. Press and hold SEARCH ∞or § until the frequency in the display starts running. ™The radio automatically tunes to a station of sufficient reception. Display shows Srch during automatic tuning. 3. Repeat step 2 if necessary until you find the desired station. • To tune to a weak station, press ∞or § briefly and repeatedly until you have found optimal reception. To improve radio reception: • For FM, extend, incline and turn the telescopic aerial. Reduce its length if the signal is too strong. • For MW , the set uses a built-in aerial. Direct this aerial by turning the whole set. Manual programmin 1. Tune to your desire stations). 2. Press PROG to act ™PROG flashes. 3. Press PRESET+ / - preset number. • Remote control (A PRESET+ / - once station. 4. Press PROG to con 5. Repeat steps 1-4 to Note : You can erase another frequency in i Autostore Autostore automatical stations from preset 1. programmed in order if reception strength. An DIGITAL TUNER Meet Philips at the Internet http://www.philips.com AZ1300 AZ1305 CD Soundmachine Audio Audio W CLASS 1 AZ 1300 AZ 1305 English Français Español Deutsch Remote Control for AZ1305 model only

In the stop position, select and store your CD tracks in the desired sequence. Up to 20 tracks can be stored in the memory. 1. Press SEARCH ∞or § on the set to select your desired track number. 2. Press PROG. ™Display: PROG, Prog briefly and your selected track number. (See 5) ™If you attempt to program without first selecting a track number, noSE is shown. 3. Repeat steps 1-2 to select and store all desired tracks. ™Display: FULL if you try to program more than 20 tracks. Reviewing the program In the stop position, press and hold PROG until the display shows all your stored track numbers in sequence. Erasing a program You can erase the program by either: • pressing 9 twice ™CLr is displayed briefly and PROG disappears. • You select MW / FM function. • Open the CD door. SAFETY & MAINT (See 7) • Don't expose the rain, sand or exc • Clean the set w cleaning agents benzene or abra • Place the set on system does not ventilation to pr • The mechanical self-lubricating b lubricated. CD player and CD • If the CD player cleaning CD to c to repair. • The lens of the C • Sudden changes can cause conde player. Playing a attempt to clean warm environme • Always close th • To clean the CD, centre towards t cloth. Do not use damage the disc • Never write on a CD PLAYER SAFETY VOLUME SEARCH PRESET TUNING REPEAT SHUFFLE SEARCH + - 1 9 8 6 7 2 4 3 5 1 2 3 4 5 6 7 8 A C M A I N S ~ ! 0 9 Remote Control for AZ1305 model only 1

Mains plug This apparatus is fitted with an approved 13 Amp plug.To change a fuse in this type of plug proceed as follows: 1.Remove fuse cover and fuse. 2.Fix new fuse which should be a BS1362 5 Amp, A.S.T.A. or BSI approved type. 3.Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appro- priate plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5 Amp. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp. Note:The severed plug must be disposed of to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere. How to connect a plug The wires in the mains lead are coloured with the following code: blue = neutral (N), brown = live (L). As these colours may not correspond with the colour markings iden- tifying the terminals in your plug, proceed as follows: • Connect the blue wire to the terminal marked N or coloured black. • Connect the brown wire to the terminal marked L or coloured red. • Do not connect either wire to the earth terminal in the plug, marked E (or e) or coloured green (or green and yellow). Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the two wires. Copyright in the U.K. Recording and playback of material may require consent. See Copyright Act 1956 and The Performer’s Protection Acts 1958 to 1972.

1 x Remote Control (for AZ1305 model only) TOP AND FRONT PANEL (See 1) 1 LIFT TO OPEN - lift here to open CD door. 2 PROG CD: - programs tracks and reviews the program; Tuner: - programs preset radio stations. 3 MODE - selects different play modes: e.g. REPEAT or SHUFFLE (random) order. 4 VOLUME 3 , 4 - to adjust volume level. PRESET+ ,- (up, down) - selects a preset radio station. 5 Display - shows the status of the set. 6 2; - starts or pauses CD playback. 9 - to stop playback or erase a CD program. SEARCH ∞, § CD: - searches backward and forward within a track; - skips to the beginning of a current track/ previous/ later track. RADIO: - (down, up) tunes to radio stations. 7 DBB (Dynamic Bass Boost) - activates a more vivid bass response. 8 POWER slider - selects CD/ MW / FM / OFF function and also the power off switch (OFF). BACK PANEL (See 1) 9 Telescopic aerial - improves FM reception. 0 Battery compartment - for 6 batteries, type R-14, UM2 or C-cells. ! AC MAINS - inlet for mains lead. REMOTE CONTROL (for AZ1305 model only) 1 VOLUME 3 , 4 - adjusts volume level. 2 SHUFFLE - plays all CD tracks in random order. 3 2; - starts or pauses CD playback. 4 SEARCH 5 , 6 - searches backwards/ forwards within a track. 5 PRESET+ ,- (up, down) - selects a preset radio station. 6 TUNING ∞, § (down, up) - tunes to tuner stations. 7 9 - to stop playback; - erases a CD program. 8 ¡ , ™- skips to the beginning of a current track previous/ subsequent track. 9 REPEAT - repeats a track /program/ entire CD. CAUTION Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. POWER SUPPLY Whenever convenient, use the AC power supply to conserve battery life. Make sure you remove the power plug from the set and wall outlet before inserting batteries. Batteries (not included) • Insert 6 batteries, type R-14, UM-2 or C-cells, (preferably alkaline) with the correct polarity. (See 6) • Remote control (AZ1305 model only) Insert 2 batteries, type AAA, R03 or UM4 (preferably alkaline). (See 8) IMPORTANT! • Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst. • Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set. • When inserting new batteries, do not try to mix old batteries with the new ones. • Batteries contain chemical substances, so they should be disposed of properly. Using AC Power 1. Check if the AC power supply, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service centre. 2. Connect the mains lead to the wall socket. 3. To disconnect the mains supply, unplug the set from the wall socket. The type plate is located on the bottom of the set. This set complies with the radio interference requirements of the European Community. For users in the U.K., please follow the boxed instructions ‘Important notes...’ on this sheet. BASIC FUNCTIONS Switching on and off a 1. To switch on, adjust CD, MW (AM), FM respective function c 2. To switch off, adjust OFF . Note : The DBB setting volume level (maximum set's memory. Adjusting volume and 1. Adjust the volume wi ™Display shows the 0-32. 2. Press DBB once or m boost on or off. ™Display: shows English CONTROL POWER SUPPLY P DIGITAL TUNER Tuning to radio stations 1. Adjust the POWER slider to MW or FM. ™The radio. station frequency, waveband are shown (See 3) 2. Press and hold SEARCH ∞or § until the frequency in the display starts running. ™The radio automatically tunes to a station of sufficient reception. Display shows Srch during automatic tuning. 3. Repeat step 2 if necessary until you find the desired station. • To tune to a weak station, press ∞or § briefly and repeatedly until you have found optimal reception. To improve radio reception: • For FM, extend, incline and turn the telescopic aerial. Reduce its length if the signal is too strong. • For MW , the set uses a built-in aerial. Direct this aerial by turning the whole set. Manual programming 1. Tune to your desired station (see Tuning to radio stations). 2. Press PROG to activate programming. ™PROG flashes. 3. Press PRESET+ / - once or more to select a preset number. • Remote control (AZ1305 models only): Press PRESET+ / - once or more to select a preset station. 4. Press PROG to confirm. 5. Repeat steps 1-4 to store other stations. Note : You can erase a preset station by storing another frequency in its place. Autostore Autostore automatically starts programming radio stations from preset 1. Available stations are programmed in order if the station with sufficient reception strength. Any previous presets e.g. manually programmed will be erased Playing a CD This CD player plays Audio Discs including CD- Recordables and CD-Rewritables. 1. Adjust the POWER slider to CD. 2. Open the CD Door. ™OPEN is displayed. 3. Insert a CD with the printed side facing up and close the door. ™nocd if no CD inserted/ CD dirty, incorrectly inserted or damaged. ™nFcd if you have inserted a non-finalized CD- R(W). 4. Press 2; to start playback. ™dAtA if your CD contains non-audio i.e. data files. 5. To pause playback press 2;. Press 2; again to resume play. ™Display: 1 flashes during pause. 6. To stop CD playback, press the 9 button. Note : CD play will also stop when: the CD door is opened Finding a passage wit 1. Press and hold SEAR – The CD is played at 2. When you recognize release ∞or § to re Note : During a CD prog REPEAT active, searchi track. Different play modes: You can select and chan before or during playbac with PROG. (See 4) (SHUFFLE) - tracks are played in random ord (SHUFFLE REP entire CD/ program cont (REPEAT ALL) - r program (REPEAT) - plays 1 To select play mode DIGITAL TUNER DIGITAL TUNER CD PLAYER

In the stop position, select and store your CD tracks in the desired sequence. Up to 20 tracks can be stored in the memory. 1. Press SEARCH ∞or § on the set to select your desired track number. 2. Press PROG. ™Display: PROG, Prog briefly and your selected track number. (See 5) ™If you attempt to program without first selecting a track number, noSE is shown. 3. Repeat steps 1-2 to select and store all desired tracks. ™Display: FULL if you try to program more than 20 tracks. Reviewing the program In the stop position, press and hold PROG until the display shows all your stored track numbers in sequence. Erasing a program You can erase the program by either: SAFETY & MAINTENANCE INFORMATION (See 7) • Don't expose the set, batteries, CDs to humidity, rain, sand or excessive heat. • Clean the set with a dry cloth. Don't use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the set. • Place the set on a hard and flat surface so that the system does not tilt. Make sure there is good ventilation to prevent the set overheating. • The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated. CD player and CD handling • If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. • The lens of the CD player should never be touched! • Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Playing a CD is then not possible. Do not No sound /power – Volume not adjusted • Adjust the VOLUME – Mains lead not securely connected • Connect the AC mains lead properly – Batteries exhausted/ incorrectly inserted • Insert (fresh) batteries correctly Severe radio hum or noise – Electrical interference: set too close to TV, VCR or computer • Move the set to increase the distance Poor radio reception – Weak radio signal • FM: Adjust the FM telescopic aerial nocd indication – CD badly scratched or dirty • Replace/ clean CD see Maintenance dAtA indication – CD contains non-a • Press SEARCH ∞ CD audio track, i The CD skips trac – CD damaged or di • Replace or clean C – SHUFFLE or PROG • Switch off SHUFF Remote control do AZ1305 model onl – Batteries exhauste • Insert (fresh) batte – Distance/ angle b • Reduce the distan DIGITAL TUNER Tuning to radio stations 1. Adjust the POWER slider to MW or FM. ™The radio. station frequency, waveband are shown (See 3) 2. Press and hold SEARCH ∞or § until the frequency in the display starts running. ™The radio automatically tunes to a station of sufficient reception. Display shows Srch during automatic tuning. 3. Repeat step 2 if necessary until you find the desired station. • To tune to a weak station, press ∞or § briefly and repeatedly until you have found optimal reception. To improve radio reception: • For FM, extend, incline and turn the telescopic aerial. Reduce its length if the signal is too strong. • For MW , the set uses a built-in aerial. Direct this aerial by turning the whole set. Programming radio stations You can store up to a total of 30 radio stations (20 FM and 10 MW) in the memory, manually or automatically (Autostore). Manual programming 1. Tune to your desired station (see Tuning to radio stations). 2. Press PROG to activate programming. ™PROG flashes. 3. Press PRESET+ / - once or more to select a preset number. • Remote control (AZ1305 models only): Press PRESET+ / - once or more to select a preset station. 4. Press PROG to confirm. 5. Repeat steps 1-4 to store other stations. Note : You can erase a preset station by storing another frequency in its place. Autostore Autostore automatically starts programming radio stations from preset 1. Available stations are programmed in order if the station with sufficient reception strength. Any previous presets e.g. manually programmed will be erased. • Press PROG for 2 seconds or more to activate autostore programming. ™The display shows AUtO, PROG blinks, followed by the radio station details when stored. After all stations are stored, the first preset station will then automatically play. To listen to a preset station • Press the PRESET+ ,- buttons once or more until the desired preset station is displayed. • Remote control (AZ1305 models only): optionally, press PRESET+ ,- to select your preset station. Playing a CD This CD player plays Audio Discs including CD- Recordables and CD-Rewritables. 1. Adjust the POWER slider to CD. 2. Open the CD Door. ™OPEN is displayed. 3. Insert a CD with the printed side facing up and close the door. ™nocd if no CD inserted/ CD dirty, incorrectly inserted or damaged. ™nFcd if you have inserted a non-finalized CD- R(W). 4. Press 2; to start playback. ™dAtA if your CD contains non-audio i.e. data files. 5. To pause playback press 2;. Press 2; again to resume play. ™Display: 1 flashes during pause. 6. To stop CD playback, press the 9 button. Note : CD play will also stop when: - the CD door is opened - the CD has reached the end - you select MW / FM function. Selecting a different track • Press SEARCH ∞or § once or repeatedly to select your track. • In the pause / stop position, press.2; to start playback. Finding a passage 1. Press and hold S – The CD is playe 2. When you recog release ∞or § Note : During a CD REPEAT active, se track. Different play mod You can select and before or during pla with PROG. (See 4 (SHUFFLE) - t are played in random (SHUFFLE entire CD/ program (REPEAT AL program (REPEAT) - p 1. To select play m 2. Press 2; to star 3. To select normal repeatedly until displayed. – You can also p play mode. DIGITAL TUNER DIGITAL TUNER CD PLAYER CD PLAYER SAFETY & MAINTENANCE TROUBLESHOOTING If a fault occurs, first check the points listed below before taking the set for If you are unable to remedy a problem by following these hints, consult your WARNING: Do not open the set as there is a risk of ele circumstances should you try to repair the invalidate the guarantee.

In the stop position, select and store your CD tracks in the desired sequence. Up to 20 tracks can be stored in the memory. 1. Press SEARCH ∞or § on the set to select your desired track number. 2. Press PROG. ™Display: PROG, Prog briefly and your selected track number. (See 5) ™If you attempt to program without first selecting a track number, noSE is shown. 3. Repeat steps 1-2 to select and store all desired tracks. ™Display: FULL if you try to program more than 20 tracks. Reviewing the program In the stop position, press and hold PROG until the display shows all your stored track numbers in sequence. Erasing a program You can erase the program by either: • pressing 9 twice SAFETY & MA (See 7) • Don't expose rain, sand or e • Clean the set cleaning agen benzene or ab • Place the set system does n ventilation to • The mechanic self-lubricatin lubricated. CD player and • If the CD play cleaning CD t to repair. • The lens of th • Sudden chang can cause con player. Playing attempt to cle DIGITAL TUNER Tuning to radio stations 1. Adjust the POWER slider to MW or FM. ™The radio. station frequency, waveband are shown (See 3) 2. Press and hold SEARCH ∞or § until the frequency in the display starts running. ™The radio automatically tunes to a station of sufficient reception. Display shows Srch during automatic tuning. 3. Repeat step 2 if necessary until you find the desired station. • To tune to a weak station, press ∞or § briefly and repeatedly until you have found optimal reception. To improve radio reception: • For FM, extend, incline and turn the telescopic aerial. Reduce its length if the signal is too strong. • For MW , the set uses a built-in aerial. Direct this aerial by turning the whole set. Programming radio stations You can store up to a total of 30 radio stations (20 FM and 10 MW) in the memory, manually or automatically (Autostore). Manual progra 1. Tune to your stations). 2. Press PROG ™PROG flas 3. Press PRESET preset numbe • Remote cont PRESET+ / - station. 4. Press PROG 5. Repeat steps Note : You can another frequen Autostore Autostore autom stations from pre programmed in o reception streng programmed wil • Press PROG f autostore pro ™The displa followed b stored. After all stations will then automa To listen to a p • Press the PRE the desired pr • Remote contr press PRESET DIGITAL TUNER CD PLAYER SAFET Meet Philips at the Internet http://www.philips.com Printed in China W CLASS 1 LASER PRODUCT AZ 1300 AZ 1305 English Français Español Deutsch Nederlands VOLUME REPEAT SHUFFLE 1 9 2 1 2 3 4 5 6 7 8 9 1

In the stop position, select and store your CD tracks in the desired sequence. Up to 20 tracks can be stored in the memory. 1. Press SEARCH ∞or § on the set to select your desired track number. 2. Press PROG. ™Display: PROG, Prog briefly and your selected track number. (See 5) ™If you attempt to program without first selecting a track number, noSE is shown. 3. Repeat steps 1-2 to select and store all desired tracks. ™Display: FULL if you try to program more than 20 tracks. Reviewing the program In the stop position, press and hold PROG until the display shows all your stored track numbers in sequence. Erasing a program You can erase the program by either: • pressing 9 twice ™CLr is displayed briefly and PROG disappears. • You select MW / FM function. • Open the CD door. SAFETY & MAINTENANCE INFORMATION (See 7) • Don't expose the set, batteries, CDs to humidity, rain, sand or excessive heat. • Clean the set with a dry cloth. Don't use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the set. • Place the set on a hard and flat surface so that the system does not tilt. Make sure there is good ventilation to prevent the set overheating. • The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated. CD player and CD handling • If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. • The lens of the CD player should never be touched! • Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. • Always close the CD door to avoid dust on the lens. • To clean the CD, wipe in a straight line from the centre towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc. • Never write on a CD or attach any stickers to it. No sound /power – Volume not adjusted • Adjust the VOLUME – Mains lead not securely connected • Connect the AC mains lead properly – Batteries exhausted/ incorrectly inserted • Insert (fresh) batteries correctly Severe radio hum or noise – Electrical interference: set too close to TV, VCR or computer • Move the set to increase the distance Poor radio reception – Weak radio signal • FM: Adjust the FM telescopic aerial nocd indication – CD badly scratched or dirty • Replace/ clean CD, see Maintenance – Laser lens steamed up • Wait until lens has cleared nFcd indication – CD-R(W) is blank/ not finalized • Use a finalized CD-R(W) dAtA indication – CD contains non-aud • Press SEARCH ∞o CD audio track, inst The CD skips tracks – CD damaged or dirty • Replace or clean CD – SHUFFLE or PROG is • Switch off SHUFFLE / Remote control does AZ1305 model only) – Batteries exhausted/ • Insert (fresh) batterie – Distance/ angle betw • Reduce the distance/ CD PLAYER SAFETY & MAINTENANCE TROUBLESHOOTING Environmental information We have done our best to reduce the packaging and make it easy to sepa cardboard, expandable polystyrene, polyethylene. Your set consists of materials which can be recycled if disasse specialized company. Please observe the local regulations reg disposal of packaging, exhausted batteries and old equipment. If a fault occurs, first check the points listed below before taking the set for rep If you are unable to remedy a problem by following these hints, consult your de WARNING: Do not open the set as there is a risk of elect circumstances should you try to repair the se invalidate the guarantee.