Honeywell HD3CHS Quick Install Manual

3 Inch Dome Camera Quick Install Guide HD3CHS/HD3CHSX Document 800-05724 – Rev C – 05/10 Important Safety Information Installation and servicing should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty. WARNING! The Use of CSA Certified/UL Listed Class 2 power adapters is required to ensure compliance with electrical safety standards. WARNING! To reduce the risk of fire or electrical shock, do not expose the product to rain or moisture. WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product (applicable in the European Union and other European countries with separate collection Security). This product should be disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures. Regulatory FCC Compliance Statement Information to the User: This equipment has been tested and found to comply with the limits for a Class A digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This Class A digital apparatus complies with Canadian ICES-003. Manufacturer’s Declaration of Conformance The manufacturer declares that the equipment supplied with this guide is compliant with the essential protection requirements of the EMC directive 89/336/EEC and the Low Voltage Directive LVD 73/23 EEC, conforming to the requirements of standards EN 55013 for emissions. Operating Notes Power Supply This dome camera can operate on 24 VAC or 12 VDC. Operating Conditions Avoid viewing very bright objects (example, light fixtures) for extended periods. Avoid operating or storing the unit in the following locations: • Extremely humid, dusty, hot/cold environments (where the operating temperature is outside the recommended range of 14°F to 122°F [-10°C to +50°C] • Close to sources of powerful radio or TV transmitters • Close to fluorescent lamps or objects reflecting light • Under unstable light sources (may cause flickering) Installation The HD3CHS Series is a fully-integrated enclosure with camera and lens. Figure 1 Camera Parts Disassembling the Camera 1. Gently turn the camera dome cover (#4 on Figure 2) counter-clockwise to unlock and pull free of the camera base. Note the two line markers. 2. Remove the inner liner (#4) by gently pulling it free of the two notches (#3) in the dome cover (#5). Set the housing, bubble (#6), and liner aside. Figure 2 Camera Disassembly Connecting the Wiring Follow Figure 1 to connect the video output connector (#a) and 24 VAC/12 VDC power connector (#b). Note For DC power supply use, make sure the polarity is correct to avoid malfunction and/or camera damage. Mounting the Camera 1. Place the supplied mounting template (#2 on Figure 3) on the mounting surface and mark the holes. 2. Drill two holes, then insert the screw anchors (#1) into the holes. 3. Remove the camera housing, if you have not already done so. 4. Secure the camera base to the wall or ceiling with the TP4 x 15 mm tapping screws supplied (#3). 5. Depending on the mounting surface mate- rial, you may require different screws and anchors than those supplied. Figure 3 Camera Installation Optional Camera Settings Camera Setup Functions See Figure 4 to locate the camera setup functions described below on the camera board. Figure 4 Camera Adjustment Functions Adjusting the Camera Position Adjusting the Camera The HD3CHS Series mini-dome camera has three axes for positioning the camera. While monitoring the picture on the monitor, adjust the camera position as follows. Figure 5 Camera Position Adjustment Horizontal Adjustment Rotate the 3D gimbal assembly in the base. Do not turn the assembly more than 360° as this may cause the internal cables to twist and disconnect or break. Vertical Adjustment After loosening the thumbnuts (see #1 on Figure 5), position the camera a desired, then finger-tighten the thumbnuts to set the position. Horizontal Rotation (Wall Mount/Ceilings) Rotate the lens base (maximum 360°) until you are satisfied with the field of view. Adjusting the Lens 1. Loosen the Zoom lever (#3) counter- clockwise a little, then rotate the Zoom lever and determine the image view. 2. Loosen the Focus lever (#4) counter- clockwise a little, then adjust the focus for optimum picture sharpness. 3. Re-tighten the Zoom lever and Focus lever after adjustment. Important: Lock the zoom and focus levers after making adjustments so the positions don’t move (for example, from temperature changes or vibrations). Configuration Use the OSD menus to set up the camera for optimum performance. Figure 6 Main Menu Setting the Lens and Brightness 1. From the Main menu, select LENS. 2. Move the joystick control LEFT or RIGHT to select DC (Automatic Iris lens). 3. Move the joystick control LEFT or RIGHT to select the desired BRIGHTNESS level. Options are: 1~/50 (default) ~ /100). CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THE UNI T. THIS SYMBOL INDICATES THAT IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS ACCOMPANY THIS UNIT. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO USER-SERVICEABLEPARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Legend a Video output connector b 24 VAC/12 VDC power input connector (red+, black-) 1 Side notch used for surface run power/video connector 2 Camera base 3 Camera housing lock 4 Camera housing 5 Bubble 6 Zoom lever 7 Focus lever 1 2 3 6 5 b a 4 7 Legend 1 Camera base (including gimbal) 2 Line markers 3 Tilt adjustment backet and thumbnuts, 2 notches 4 Inner liner 5 Camera housing 6 Bubble 1 5 4 3 6 2 3 1 Legend 1 Screw anchors (x2), supplied 2 Mounting template 3 TP4 x 15 mm tapping screws (x2), supplied 2 2-Anchor hold  6 1/4” dia. depth about 22 mm Guide pattern Logo direction MON UP UP MON PC OP Legend 1 OSD joystick control 2 Monitor out OSD joystick control to navigate through the menus Press the OSD joystick control straight down: • for two seconds to enter the Main menu. • to enter a screen or to select a submenu option. A selected menu item blinks. If no settings are made, the menu disappears after a few seconds. Move the OSD joystick control (#1) UP, DOWN, LEFT, or RIGHT to move to and between menus and options. Select RETURN END to save all settings and exit the menu. Select RETURN RES to save all settings and return to the previous selection. 1 2 3 5 4 Legend 1 Tilt adjustment bracket and thumbnuts (x2) 2 Axis ring (for horizontal rotation on wall mount and tilted ceilings) 3 Zoom lever 4 Focus lever 5 3D gimbal assembly in housing base (for horizontal adjustment) LENS DC EXPOSURE  WHITE BAL AWB DAY/NIGHT AUTO 3DNR OFF SPECIAL  ADJUST  RESET  EXIT LENS EXPOSURE WHITE BAL DAY/NIGHT 3DNR SPECIAL ADJUST RESET DC BRIGHTNESS SHUTTER AGC SENS-UP BLC D-WDR AWB AUTO COLOR B/W EXT CAM TITLE D-EFFECT MOTION PRIVACY SYNC VER. SHARPNESS BLUE RED FACTORY LEVEL

[email protected] © 2010 Honeywell International Inc. Document 800-05724 – Rev C – 05/10 Optimizing the Lens Setup Setting Day/Night Control Setting the Digital Noise Reduction To set the digital 3D noise reduction function, select MAIN MENU, then 3DNR. Options are: ON (default) or OFF, where you can adjust the level from 0 to 100. SPECIAL Menu Functions . Set the Image Sharpness Level To set the level of sharpness of the image, select MAIN MENU ➤ ADJUST. In the ADJUST submenu you can adjust the SHARPNESS, from 0 to 31 (16 is the default). OSD Default Settings To restore the factory default settings, select SETUP ➤ RESET ➤ FACTORY. Completing the Installation Attaching and Securing the Dome Cover To attach the dome cover, follow Figure 7: 1. Use a soft, lint-free cloth to wipe the dome cover clean and remove fingerprints. 2. Attach the inner liner (#4) to the Tilt adjust- ment thumbnuts (#2). Push the unit down until it clicks into place. 3. Place the dome housing and bubble (#5) on the camera base (#1). 4. Align the line markers on the dome housing with those on the base. Turn the dome housing gently clockwise until it locks in place. 5. Secure the dome cover to the camera base with the TP1.7 screw (#6). Figure 7 Dome Housing Installation Routine Maintenance • The dome bubble is an optical part. Use a soft, dry cloth to remove any fingerprints or dust. • Clean the camera housing with a soft, dry cloth. For more stubborn stains, use a cloth dampened with a small quantity of neutral detergent, then wipe dry. Caution Do not use volatile solvents such as alcohol, benzene or thinners to avoid damaging the surface finish. Product Dimensions Figure 8 Camera Dimensions Accessory Mounting Application When required, you can use the camera mounting holes (see Figure 8) to fit the camera base easily on a single gang electrical box using the HD3-MK pendant/wall mount kit. For more information, contact Honeywell Technical Support or your sales representative (see back cover for contact information). Warranty and Service Subject to the terms and conditions listed on the Product warranty, during the warranty period Honeywell will repair or replace, at its sole option, free of charge, any defective product returned prepaid. In the event you have a problem with any Honeywell product, please call Customer Service for assistance or to request a Return Merchandise Authorization (RMA) number. Call 1.800.796.CCTV (North America only). Be sure to have the model number, serial number, and the nature of the problem available for the technical service representative. Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped to Honeywell without a clearly identified Return Merchandise Authorization (RMA) number may be refused. Specifications MAIN MENU ➤ EXPOSURE SHUTTER Select a shutter speed: 1/60 / 1/50 (default) sec. FLK (Flickerless) Reduces on-screen flickering. Caution When set to FLK, SENS-UP is disabled. AGC OFF, HIGH, MIDDLE, (default), LOW. SENS-UP Set the Sense-Up function. Move the joystick control Left/Right to select: AUTO mode to then select a value from x2 to x256, or OFF (default) mode. BLC Backlight compensation. Control the light level to overcome severe backlighting conditions. Select from: OFF (default) BLC to set the gain. HSBLC to set the image sensitivity level, from 1 to 8. BLC and HSBLC both have an AREA SETUP submenu. D-WDR Digital wide dynamic range. Select from: OFF (default) INDOOR OUTDOOR MAIN MENU ➤ WHITE BALANCE AWB Controls color on the screen. ATW (Auto Tracing White Balance) Select when the scene illumination varies between indoor scenes and outdoor scene lighting. AWB (Auto White Balance) (default) AWC Automatically adjust the white balance to your specific environment. Press SET to adjust. MANUAL. In Manual mode you can adjust the red and blue settings, from 0 to 100. INDOOR OUTDOOR MAIN MENU ➤ DAY/NIGHT Use this menu to set how the camera adjusts to low light.T AUTO (default) Depending on light level, the camera automatically switches from color to black and white. Select this mode to set: DELAY: Set the time before the camera switches to Day or Night mode after detecting a switching threshold. D-->N (Day to Night): The relative light level at which the camera switches to Night mode. The higher the value, the darker the lighting (the lower the lux) must be before the camera switches. Set D-->N should be set at least 3 less than N-->D. N-->D (Night to Dayl): The relative light level at which the camera switches to Day mode. The lower the value, the brighter the lighting (the higher the lux) must be before the camera switches. DAY/NIGHT mode must be set to AUTO to use this function. COLOR Forces the camera to stay in Day (color) mode at all times. B/W Forces the camera to stay in Night (B/W) mode at all times. The B/W submenu allows you to select Color Burst to be ON or OFF. Note Certain video recorders require color burst to operate. GAIN MIDDLE DEFAULT  LEFT/RIGHT 4 WIDTH 4 TOP/BOTTOM 3 HEIGHT 4 RETURN RET AUTO COLOR BW RETURN RET DELAY 15 D-->N 27 N-->D 13 RETURN RET MAIN MENU ➤ SPECIAL CAM TITLE Set to ON to add a camera title (up to 15 characters).You can also select where the title appears on the monitor screen. D-EFFECT Digital Effects. D-EFFECT options are: MIRROR: OFF (default), ROTATE, V-FLIP, MIRROR D-ZOOM: • ON = D-ZOOM submenu where you can adjust PAN, TILT. • OFF (default) GAMMA: Set the value, from 0.05 to 1.0 (0.45 is the default and is typically the default value for CCTV CRT monitors) NEG. IMAGE: ON, OFF (default) MOTION Detect moving objects on screen. Select up to 4 areas on screen you want to observe. You can also set the motion detection sensitivity, from 0 to 40. WIDTH: [values] TOP/BOTTOM: [values] HEIGHT: SENSITIVITY: 0 to 40 MOTION VIEW: • ON = the image flickers when the camera detects moving objects. • OFF = the monitor displays MOTION DETECTION. PRIVACY Mask up to 8 privacy areas on the screen from video monitoring. AREA DISPLAY LEFT/RIGHT: WIDTH: TOP/BOTTOM: HEIGHT: COLOR: Select one of 15 colors for the privacy zone. SYNC Select the Sync mode, from: INT (Internal, is the default) LL (Line Lock). LL only works with AC power. VER. Displays the firmware version on the camera. CAM TITLE OFF D-EFFECT MOTION OFF PRIVACY OFF SYNC INT VER. A00003 RETURN RET FREEZE OFF MIRROR OFF D-ZOOM OFF GAMMA 0.45 NEG. IMAGE OFF RETURN RET 1 4 5 3 Legend 1 Camera base 2 Line markers 3 Tilt adjustment thumbnuts 4 Inner liner 5 Dome housing and bubble 6 TP1.7 screw 6 2 (Min.) 3.23” (82 mm) 4.41” (112.1 mm) 3.97” (100.8 mm) (Min.) 3.39” (86 mm) Video Signal Specifications NTSC PAL Video Standard: Scanning System: 525 lines, 2:1 Interlace Image Sensor: 1/3” SuperHAD2 (Sony CCD) Number of Pixels (H x V): 768 x 494 811 x 508 Minimum Illumination: 0.2 lux @ F1.2 (AGC on, 50 IRE) Horizontal Resolution: 520 TVL Video Output: 1.0 Vp-p @ 75 Ohms Sync System: 12 VDC: Internal, 24 VAC: Line lock S/N Ratio: <50 dB (AGC Off) Auto Electronic Shutter: 1/60 - 1/100,000 sec 1/50 - 1/100,000 sec AI/AES Selection: On/off, switchable White Balance: ATW/AWB/AWC > Set/Manual/ Indoor/Outdoor BLC Off/BLC/HSBLC Gamma: 0.45, adjustable Sense-Up: Off/Auto, selectable D-WDR: Off/Indoor/Outdoor, selectable Privacy Mask: 8 mask areas, configurable Motion Detection: 4 motion detection areas, configurable Mirror: Off/Mirror/V-Flip/Rotate, selectable 3DNR: Off/On, adjustable Lens Type: 2.8 mm to 10.5 mm Vari-focal Auto Iris, F1.2 Lens Iris Control: Direct Drive (DC) AI Angle of View (Lens): Horizontal: 76.1° (wide), -23.8° (tele) Vertical: 55.8° (wide), -17.9° (tele) Electrical Specifications Input Voltage: 12 VDC/24 VAC Input Tolerance: ± 15% Power Consumption: 3.5 W (max) Mechanical Dimensions (WxH): 4.41” x 3.97” (112.1 mm x 100.6 mm) Weight: .66 lbs (.3 Kg) Net, 1.32 lbs (.6 Kg) Shipping Construction: Housing and dome: Polycarbonate Environmental Temperature: Operating: -14°F to 122°F (-10°C to 50°C) Storage: -4°F to 140°F (-20°C to 60°C)) Relative Humidity: 0% to 90%, non-condensing Regulatory Emissions FCC, CE (EN55022) Immunity CE (EN50130-4) Safety EU: LVD 2006/95/EC