Philips AZ1310/19 Operation & User’s Manual

1 LIFT TO OPEN - lift here to open CD door. 2 PROG CD: - programs tracks and reviews the program; Tuner: - programs preset radio stations. 3 MODE - selects different play modes: e.g. REPEAT or SHUFFLE (random) order. 4 VOLUME 3 , 4 - to adjust volume level. PRESET+ ,- (up, down) - selects a preset radio station. 5 Display - shows the status of the set. 6 2; - starts or pauses CD playback. 9 - to stop playback or erase a CD program. SEARCH ∞, § CD: - searches backward and forward within a track; - skips to the beginning of a current track/ previ- ous/ later track. RADIO: - (down, up) tunes to radio stations. 7 DBB (Dynamic Bass Boost) - activates a more vivid bass response. 8 CASSETTE RECORDER keys: RECORD 0 - to start recording. PLAY 1 - to start playback. SEARCH 5 / 6 - fast rewinds/ winds tape. OPEN•STOP 0 9 - stops the tape; - open the cassette compartment. PAUSE ; - pauses playback or recording. 9 POWER slider - selects TAPE/ MW / FM / CD function and also the power off switch (TAPE/ OFF). BACK PANEL (See 1) 0 Telescopic aerial - improves FM reception. ! Battery compartment - for 6 batteries, type R-14, UM2 or C-cells. @ AC MAINS - inlet for mains lead. CAUTION Use of controls or adjustments or performance of pro- cedures other than herein may result in hazardous radiation exposure or other unsafe operation. POWER SUPPLY Whenever convenien conserve battery life power plug from the inserting batteries. Batteries (not incl • Insert 6 batteries, (preferably alkaline IMPORTANT! • Incorrect use of b leakage and will c the batteries to b • Do not mix batter zinc. Only use bat set. • When inserting n batteries with the • Batteries conta they should be d Using AC Power 1. Check if the AC p type plate loca corresponds to yo not, consult your 2. Connect the main 3. To disconnect the from the wall soc The type plate is l set. This set complies requirements of th For users in the U instructions ‘Impo English CONTROL Autostore Autostore automatically starts programming radio stations from preset 1. Available stations are programmed in order if the station with sufficient reception strength. Any previous presets e.g. manually programmed will be erased. • Press PROG for 2 seconds or more to activate autostore programming. ™The display shows AUtO, PROG blinks, followed by the radio station details when stored. After all stations are stored, the first preset station will then automatically play. To listen to a preset station • Press the PRESET+ ,- buttons once or more until the desired preset station is displayed. CD PLAYER Playing a CD This CD player plays Recordables and CD 1. Adjust the POWE 2. Open the CD Doo ™OPEN is disp 3. Insert a CD with close the door. ™nocd if no C inserted or da ™nFcd if you R(W). 4. Press 2; to start ™dAtA if your files. 5. To pause playbac resume play. ™Display flashe 6. To stop CD playb Note : CD play will - the CD do - the CD ha - you select DIGITAL TUNER Meet Philips at the Internet http://www.philips.com AZ1310 AZ1310 CD Soundmachine W CLASS 1 AZ 1310 English Français Español Deutsch

1. Adjust the POWER slider to CD. 2. Insert a CD and if desired, program track numbers. 3. Insert a suitable tape into the cassette deck and close the door. 4. Press RECORD 0 to start recording. – Playing of the CD program starts automatically from the beginning of the program. You don't need to start the CD player separately. To select and record a particular passage within a CD track: • Press SEARCH ∞or §. Release the control when you recognize the passage you want. • To pause CD playback, press 2;. • Recording starts from this exact point in the track when you press RECORD 0. 5. To pause recording, press PAUSE ;. Press PAUSE ; again to resume recording. 6. To stop recording, press OPEN•STOP 0 9. Recording from the Radio 1. Tune to the desired radio station (see Tuning to radio stations). 2. Follow steps 3-6, under CD Synchro Start Recording. SAFETY & MAINT (See 7) • Don't expose the humidity, rain, sa • Clean the set wit ing agents contai or abrasives as th • Place the set on a system does not t lation to prevent • The mechanical p cating bearings a CD player and CD • If the CD player c cleaning CD to cle to repair. • The lens of the C • Sudden changes can cause conden player. Playing a C attempt to clean warm environmen • Always close the on the lens. • To clean the CD, w centre towards th cloth. Do not use damage the disc. • Never write on a Tape deck mainten To ensure quality rec deck, clean parts A month. Use a cotton hol or a special head 1. Open the tape do 2. Press PLAY 1 an 3. Press PAUSE ; a capstan B. 4. After cleaning, p Note: Cleaning of the head cleaning cassette th CASSETTE RECORDER SAFETY & M A C M A I N S ~ 0 ! 1 2 3 4 5 7 8 9 @ 1 6

Mains plug This apparatus is fitted with an approved 13 Amp plug.To change a fuse in this type of plug proceed as follows: 1.Remove fuse cover and fuse. 2.Fix new fuse which should be a BS1362 5 Amp, A.S.T.A. or BSI approved type. 3.Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appro- priate plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5 Amp. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp. Note:The severed plug must be disposed of to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere. How to connect a plug The wires in the mains lead are coloured with the following code: blue = neutral (N), brown = live (L). As these colours may not correspond with the colour markings identi- fying the terminals in your plug, proceed as follows: • Connect the blue wire to the terminal marked N or coloured black. • Connect the brown wire to the terminal marked L or coloured red. • Do not connect either wire to the earth terminal in the plug, marked E (or e) or coloured green (or green and yellow). Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the two wires. Copyright in the U.K. Recording and playback of material may require consent. See Copyright Act 1956 and The Performer’s Protection Acts 1958 to 1972.

1 LIFT TO OPEN - lift here to open CD door. 2 PROG CD: - programs tracks and reviews the program; Tuner: - programs preset radio stations. 3 MODE - selects different play modes: e.g. REPEAT or SHUFFLE (random) order. 4 VOLUME 3 , 4 - to adjust volume level. PRESET+ ,- (up, down) - selects a preset radio station. 5 Display - shows the status of the set. 6 2; - starts or pauses CD playback. 9 - to stop playback or erase a CD program. SEARCH ∞, § CD: - searches backward and forward within a track; - skips to the beginning of a current track/ previ- ous/ later track. RADIO: - (down, up) tunes to radio stations. 7 DBB (Dynamic Bass Boost) - activates a more vivid bass response. 8 CASSETTE RECORDER keys: RECORD 0 - to start recording. PLAY 1 - to start playback. SEARCH 5 / 6 - fast rewinds/ winds tape. OPEN•STOP 0 9 - stops the tape; - open the cassette compartment. PAUSE ; - pauses playback or recording. 9 POWER slider - selects TAPE/ MW / FM / CD function and also the power off switch (TAPE/ OFF). BACK PANEL (See 1) 0 Telescopic aerial - improves FM reception. ! Battery compartment - for 6 batteries, type R-14, UM2 or C-cells. @ AC MAINS - inlet for mains lead. CAUTION Use of controls or adjustments or performance of pro- cedures other than herein may result in hazardous radiation exposure or other unsafe operation. POWER SUPPLY Whenever convenient, use the AC power supply to conserve battery life. Make sure you remove the power plug from the set and wall outlet before inserting batteries. Batteries (not included) • Insert 6 batteries, type R-14, UM-2 or C-cells, (preferably alkaline) with the correct polarity. (See 6) IMPORTANT! • Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst. • Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set. • When inserting new batteries, do not try to mix old batteries with the new ones. • Batteries contain chemical substances, so they should be disposed of properly. Using AC Power 1. Check if the AC power supply, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service centre. 2. Connect the mains lead to the wall socket. 3. To disconnect the mains supply, unplug the set from the wall socket. The type plate is located on the bottom of the set. This set complies with the radio interference requirements of the European Community. For users in the U.K., please follow the boxed instructions ‘Important notes...’ on this sheet. BASIC FUNCTIONS Switching on and off and selecting function 1. To switch on, adjust the POWER slider to select: CD, MW (AM), FM or TAPE function, and operate the respective function controls. 2. To switch off, adjust the POWER slider to select TAPE/OFF and make sure all the cassette keys are released. Note : The DBB setting, tuner presets and the volume level (maximum to 20) will be retained in the set's memory. Adjusting volume and sound (See 2) 1. Adjust the volume with the VOLUME controls. ™Display shows the volume level in number from 0-32. 2. Press DBB once or more to select dynamic bass boost on or off. ™Display: shows when activated. DIGITAL TUNER Tuning to radio statio 1. Adjust the POWER ™The radio. station shown (See 3) 2. Press and hold SEAR frequency in the disp ™The radio automa sufficient receptio during automatic 3. Repeat step 2 if nec desired station. • To tune to a weak st and repeatedly until reception. To improve radio rece • For FM, extend, incli ial. Reduce its length • For MW , the set use aerial by turning the Programming radio st You can store up to a to and 10 MW) in the mem (Autostore). Manual programming 1. Tune to your desired stations). 2. Press PROG to activ ™PROG flashes. 3. Press PRESET+ / - preset number. 4. Press PROG to conf 5. Repeat steps 1-4 to Note : You can erase a another frequency in its English CONTROL POWER SUPPLY POWER SUPPLY Autostore Autostore automatically starts programming radio stations from preset 1. Available stations are programmed in order if the station with sufficient reception strength. Any previous presets e.g. manually programmed will be erased. • Press PROG for 2 seconds or more to activate autostore programming. ™The display shows AUtO, PROG blinks, followed by the radio station details when stored. After all stations are stored, the first preset station will then automatically play. To listen to a preset station • Press the PRESET+ ,- buttons once or more until the desired preset station is displayed. CD PLAYER Playing a CD This CD player plays Audio Discs including CD- Recordables and CD-Rewritables. 1. Adjust the POWER slider to CD. 2. Open the CD Door. ™OPEN is displayed. 3. Insert a CD with the printed side facing up and close the door. ™nocd if no CD inserted/ CD dirty, incorrectly inserted or damaged. ™nFcd if you have inserted a non-finalized CD- R(W). 4. Press 2; to start playback. ™dAtA if your CD contains non-audio i.e. data files. 5. To pause playback press 2;. Press 2; again to resume play. ™Display flashes during pause. 6. To stop CD playback, press the 9 button. Note : CD play will also stop when: - the CD door is opened - the CD has reached the end - you select TAPE or MW / FM function. Selecting a different track Different play modes: SHUFFLE and REPEAT You can select and change the various play modes before or during playback, and combine the modes with PROG. (See 4) (SHUFFLE) - tracks of the entire CD/ program are played in random order (SHUFFLE REPEAT ALL) - to repeat the entire CD/ program continuously in random order (REPEAT ALL) - repeats the entire CD/ program (REPEAT) - plays the current track continuously 1. To select play mode, press MODE once or more. 2. Press 2; to start playback if in the stop position. 3. To select normal playback, press MODE repeated- ly until the various modes are no longer displayed. – You can also press the 9 button to cancel your play mode. Programming track numbers In the stop position, select and store your CD tracks in the desired sequence. Up to 20 tracks can be stored in the memory. 1. Press SEARCH ∞or § on the set to select your desired track number. 2. Press PROG. ™Display: PROG, Prog briefly and your select- ed track number (See 5) Erasing a program You can erase the progr • pressing 9 twice ™CLr is displayed disappears. • You select TAPE or M • Open the CD door. CASSETTE RECORDE Cassette playback 1. Adjust the POWER ™Display: shows t operation. 2. Insert a cassette as 3. Press PLAY 1 to sta 4. To pause playback p resume. 5. Press SEARCH 5 o 6. To stop the tape, pre The keys are automatica tape and the set switch been activated. General information o • Recording is permiss other rights of third p DIGITAL TUNER CD PLAYER CD PLAYER CASSE

1. Adjust the POWER slider to CD. 2. Insert a CD and if desired, program track numbers. 3. Insert a suitable tape into the cassette deck and close the door. 4. Press RECORD 0 to start recording. – Playing of the CD program starts automatically from the beginning of the program. You don't need to start the CD player separately. To select and record a particular passage within a CD track: • Press SEARCH ∞or §. Release the control when you recognize the passage you want. • To pause CD playback, press 2;. • Recording starts from this exact point in the track when you press RECORD 0. 5. To pause recording, press PAUSE ;. Press PAUSE ; again to resume recording. 6. To stop recording, press OPEN•STOP 0 9. Recording from the Radio 1. Tune to the desired radio station (see Tuning to radio stations). 2. Follow steps 3-6, under CD Synchro Start Recording SAFETY & MAINTENANCE INFORMATION (See 7) • Don't expose the set, batteries, CDs or cassettes to humidity, rain, sand or excessive heat. • Clean the set with a dry cloth. Don't use any clean- ing agents containing alcohol, ammonia, benzene or abrasives as these may harm the set. • Place the set on a hard and flat surface so that the system does not tilt. Make sure there is good venti- lation to prevent the set overheating. • The mechanical parts of the set contain self-lubri- cating bearings and must not be oiled or lubricated. CD player and CD handling • If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. • The lens of the CD player should never be touched! • Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. • Always close the CD and tape door to avoid dust on the lens. • To clean the CD wipe in a straight line from the No sound /power – Volume not adjusted • Adjust the VOLUME – Mains lead not securely connected • Connect the AC mains lead properly – Batteries exhausted/ incorrectly inserted • Insert (fresh) batteries correctly Severe radio hum or noise – Electrical interference: set too close to TV, VCR or computer • Move the set to increase the distance Poor radio reception – Weak radio signal • FM: Adjust the FM telescopic aerial nocd indication – CD badly scratched or dirty dAtA indication – CD contains non-audio • Press SEARCH ∞or CD audio track, instea The CD skips tracks – CD damaged or dirty • Replace or clean CD – SHUFFLE or PROG is ac • Switch off SHUFFLE / P Poor cassette sound q – Dust and dirt on the he • Clean deck parts, see M – Use of incompatible ca CHROME) • Only use NORMAL (IEC Recording does not w Autostore Autostore automatically starts programming radio stations from preset 1. Available stations are programmed in order if the station with sufficient reception strength. Any previous presets e.g. manually programmed will be erased. • Press PROG for 2 seconds or more to activate autostore programming. ™The display shows AUtO, PROG blinks, followed by the radio station details when stored. After all stations are stored, the first preset station will then automatically play. To listen to a preset station • Press the PRESET+ ,- buttons once or more until the desired preset station is displayed. CD PLAYER Playing a CD This CD player plays Audio Discs including CD- Recordables and CD-Rewritables. 1. Adjust the POWER slider to CD. 2. Open the CD Door. ™OPEN is displayed. 3. Insert a CD with the printed side facing up and close the door. ™nocd if no CD inserted/ CD dirty, incorrectly inserted or damaged. ™nFcd if you have inserted a non-finalized CD- R(W). 4. Press 2; to start playback. ™dAtA if your CD contains non-audio i.e. data files. 5. To pause playback press 2;. Press 2; again to resume play. ™Display flashes during pause. 6. To stop CD playback, press the 9 button. Note : CD play will also stop when: - the CD door is opened - the CD has reached the end - you select TAPE or MW / FM function. Selecting a different track • Press SEARCH ∞or § once or repeatedly to select your track. • In the pause / stop position, press.2; to start playback. Finding a passage within a track 1. Press and hold SEARCH ∞or §. – The CD is played at high speed and low volume. 2. When you recognize the passage you want, release ∞or § to resume normal playback. Note : During a CD program or if SHUFFLE/ REPEAT active, searching is only possible within a track. Different play modes: SHUFFLE and REPEAT You can select and change the various play modes before or during playback, and combine the modes with PROG. (See 4) (SHUFFLE) - tracks of the entire CD/ program are played in random order (SHUFFLE REPEAT ALL) - to repeat the entire CD/ program continuously in random order (REPEAT ALL) - repeats the entire CD/ program (REPEAT) - plays the current track continuously 1. To select play mode, press MODE once or more. 2. Press 2; to start playback if in the stop position. 3. To select normal playback, press MODE repeated- ly until the various modes are no longer displayed. – You can also press the 9 button to cancel your play mode. Programming track numbers In the stop position, select and store your CD tracks in the desired sequence. Up to 20 tracks can be stored in the memory. 1. Press SEARCH ∞or § on the set to select your desired track number. 2. Press PROG. ™Display: PROG, Prog briefly and your select- ed track number. (See 5) ™If you attempt to program without first selecting a track number, noSE is shown. 3. Repeat steps 1-2 to select and store all desired tracks. ™Display: FULL if you try to program more than 20 tracks. Reviewing the program In the stop position, press and hold PROG until the display shows all your stored track numbers in sequence. Erasing a program You can erase the progra • pressing 9 twice ™CLr is displayed disappears. • You select TAPE or M • Open the CD door. CASSETTE RECORDER Cassette playback 1. Adjust the POWER s ™Display: shows tA operation. 2. Insert a cassette as s 3. Press PLAY 1 to star 4. To pause playback pr resume. 5. Press SEARCH 5 or 6. To stop the tape, pre The keys are automatica tape and the set switche been activated. General information o • Recording is permissi other rights of third p • For recording, use onl (IEC type I) on which broken. This deck is n CHROME (IEC II) or M cassettes. • The best recording lev Altering the VOLUME affect the recording. • To protect a tape from out the tabs. If you w tabs with a piece of a DIGITAL TUNER CD PLAYER CD PLAYER CASSE CASSETTE RECORDER SAFETY & MAINTENANCE TROUBLESHOOTING If a fault occurs, first check the points listed below before taking the set for repa If you are unable to remedy a problem by following these hints, consult your dea WARNING: Do not open the set as there is a risk of electri cumstances should you try to repair the set yo invalidate the guarantee.

1. Adjust the POWER slider to CD. 2. Insert a CD and if desired, program track numbers. 3. Insert a suitable tape into the cassette deck and close the door. 4. Press RECORD 0 to start recording. – Playing of the CD program starts automatically from the beginning of the program. You don't need to start the CD player separately. To select and record a particular passage within a CD track: • Press SEARCH ∞or §. Release the control when you recognize the passage you want. • To pause CD playback, press 2;. • Recording starts from this exact point in the track when you press RECORD 0. 5. To pause recording, press PAUSE ;. Press PAUSE ; again to resume recording. 6. To stop recording, press OPEN•STOP 0 9. Recording from the Radio 1. Tune to the desired radio station (see Tuning to radio stations). 2. Follow steps 3-6, under CD Synchro Start Recording SAFETY & M (See 7) • Don't expos humidity, ra • Clean the s ing agents c or abrasives • Place the se system doe lation to pre • The mechan cating bear CD player an • If the CD pl cleaning CD to repair. • The lens of • Sudden cha can cause c player. Play attempt to c warm enviro • Always clos on the lens. • To clean the Autostore Autostore automatically starts programming radio stations from preset 1. Available stations are programmed in order if the station with sufficient reception strength. Any previous presets e.g. manually programmed will be erased. • Press PROG for 2 seconds or more to activate autostore programming. ™The display shows AUtO, PROG blinks, followed by the radio station details when stored. After all stations are stored, the first preset station will then automatically play. To listen to a preset station • Press the PRESET+ ,- buttons once or more until the desired preset station is displayed. CD PLAYER Playing a CD This CD player Recordables a 1. Adjust the 2. Open the C ™OPEN i 3. Insert a CD close the do ™nocd i inserted ™nFcd i R(W). 4. Press 2; to ™dAtA i files. 5. To pause pl resume pla ™Display 6. To stop CD Note : CD pla - the C - the C - you Selecting a d • Press SEAR select your • In the pause playback. Finding a pas 1. Press and h – The CD is 2. When you r release ∞ Note : During REPEAT activ track. DIGITAL TUNER CASSETTE RECORDER SAFETY Meet Philips at the Internet http://www.philips.com Printed in China W CLASS 1 LASER PRODUCT AZ 1310 English Français Español Deutsch Nederlands 1 2 3 4 5 7 8 9 1 6

1. Adjust the POWER slider to CD. 2. Insert a CD and if desired, program track numbers. 3. Insert a suitable tape into the cassette deck and close the door. 4. Press RECORD 0 to start recording. – Playing of the CD program starts automatically from the beginning of the program. You don't need to start the CD player separately. To select and record a particular passage within a CD track: • Press SEARCH ∞or §. Release the control when you recognize the passage you want. • To pause CD playback, press 2;. • Recording starts from this exact point in the track when you press RECORD 0. 5. To pause recording, press PAUSE ;. Press PAUSE ; again to resume recording. 6. To stop recording, press OPEN•STOP 0 9. Recording from the Radio 1. Tune to the desired radio station (see Tuning to radio stations). 2. Follow steps 3-6, under CD Synchro Start Recording. SAFETY & MAINTENANCE INFORMATION (See 7) • Don't expose the set, batteries, CDs or cassettes to humidity, rain, sand or excessive heat. • Clean the set with a dry cloth. Don't use any clean- ing agents containing alcohol, ammonia, benzene or abrasives as these may harm the set. • Place the set on a hard and flat surface so that the system does not tilt. Make sure there is good venti- lation to prevent the set overheating. • The mechanical parts of the set contain self-lubri- cating bearings and must not be oiled or lubricated. CD player and CD handling • If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. • The lens of the CD player should never be touched! • Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. • Always close the CD and tape door to avoid dust on the lens. • To clean the CD, wipe in a straight line from the centre towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc. • Never write on a CD or attach any stickers to it. Tape deck maintenance To ensure quality recording and playback of the tape deck, clean parts A, B and C as shown, once a month. Use a cotton bud slightly moistened with alco- hol or a special head cleaning fluid to clean the deck. 1. Open the tape door. 2. Press PLAY 1 and clean the roller C. 3. Press PAUSE ; and clean the heads A, and the capstan B. 4. After cleaning, press OPEN•STOP 0 9. Note: Cleaning of the heads can also be done by playing a cleaning cassette through once. No sound /power – Volume not adjusted • Adjust the VOLUME – Mains lead not securely connected • Connect the AC mains lead properly – Batteries exhausted/ incorrectly inserted • Insert (fresh) batteries correctly Severe radio hum or noise – Electrical interference: set too close to TV, VCR or computer • Move the set to increase the distance Poor radio reception – Weak radio signal • FM: Adjust the FM telescopic aerial nocd indication – CD badly scratched or dirty • Replace/ clean CD, see Maintenance – Laser lens steamed up • Wait until lens has cleared nFcd indication – CD-R(W) is blank/ not finalized • Use a finalized CD-R(W) dAtA indication – CD contains non-audio • Press SEARCH ∞or CD audio track, instea The CD skips tracks – CD damaged or dirty • Replace or clean CD – SHUFFLE or PROG is ac • Switch off SHUFFLE / P Poor cassette sound q – Dust and dirt on the he • Clean deck parts, see M – Use of incompatible ca CHROME) • Only use NORMAL (IEC Recording does not w – Cassette tab(s) may be • Apply adhesive tape ov CASSETTE RECORDER SAFETY & MAINTENANCE TROUBLESHOOTING Environmental information We have done our best to reduce the packaging and make it easy to separ cardboard, expandable polystyrene, polyethylene. Your set consists of materials which can be recycled if disassem specialized company. Please observe the local regulations rega disposal of packaging, exhausted batteries and old equipment. If a fault occurs, first check the points listed below before taking the set for repai If you are unable to remedy a problem by following these hints, consult your deal WARNING: Do not open the set as there is a risk of electri cumstances should you try to repair the set you invalidate the guarantee.