Capital PSCT484BG Installation Manual

P E R F O R M A N C E S E R I E S ™ G A S C O O K T O P S THE POWER OF PERFORMANCE™ I N S TA L L AT I O N G U I D E P E R F O R M A N C E S E R I E S ™ G A S C O O K T O P S ...

We thank you for choosing our Performance Series™ cooking equipment. Because of the unique features found in our products, we recommend spending some time to familiarize yourself with this booklet before using your product. In it you will find valuable information on how to safely operate and maintain your appliance for years of enjoyable cooking. We understand that questions arise from time to time on use and care about ...

INSTALLER: Please leave these Installation Instructions with the unit for the owner. OWNER: Please retain these instructions for future reference. This appliance was designed for ease of installation and operation. However, we recommend that you read all sections of this manual before beginning installation and that your range is installed by an approved gas installation tech ...

of three available back-guards must be ordered separately and installed at the back of the cooktop for combustible materials less than 12" from cooking surface. The three back-guard choices include 12" Low Back, 22" High-Back, or 22" High-Shelf. Before using the cooktop ensure that it is equipped with a proper back-guard. Refer to the Installation Instructions accompanying this ...

INTRODUCTION ............................................................................................................ i WARNINGS ................................................................................................................ii, iii MODELS ........................................................................................................................iv UNPACKING & HANDLING ...................................... ...

NOTE: If a solid side cabinet wall exists on one or both sides, you will need to notch the front corner of the cabinet to match the counter top notch and to provide clearance for the cooktop front (see page 8). STEP ONE ANCHORING THE COOKTOP The cooktop has a shipping weight of approximately 228 pounds (36” models) and 324 pounds (48” models). After removal of packing materials, it is recommended that the grates and drip pan (b ...

openings should be prepared by a qualified cabinet worker. We recommend having the cooktop available before cutting the opening for a more accurate measurement and verification of all installation dimensions. 2) The clearance shown in fig. 5 pg.11 is required for all types of backguard installations. 3) The cooktop is designed to hang from the countertop from its side flanges. The ...

6) Cut the openings for the following installation: Standard counter top installation, see Fig. 5A Deep counter or island installation, see Fig. 5B NOTE: If the deck is used, the sides or bottom of the cutout may be solid combustible or non- combustible material. If the bottom is solid, provided a 6” x 6” cutout in the left rear corner for the gas inlet and power cord clearance. Fig. 2 Fig. 3 Fig. 4 ...

(If installing a full backguard with the cooktop) A) Vent Hood B) Backguard System C) Cooktop 1) Locate cooktop according to cooktop installation instructions. 2) Measure distance from counter surface to top of trim on cooktop adding 1/8” for backguard clearance. 3) Transfer this measurement to the wall. This will mark the bottom of your backguard. 4) From this line measure 30-1/16” up wall ...

Secure the backguard to the wall behind the cooktop. Specific instructions for installation of the High Shelf or Low Backguards can be found packaged with the backguard. See also page 5. The backguard must be installed when there is less than a 12” clearance between combustibles and the back of the cooktop (above the cooking surface. STEP 5: ELECTRICAL CONNECTI ...

STEP 6: HOOK-UP A manual valve must be installed external to the appliance, in an accessible location from the front for the purpose of shutting off the gas supply. Make sure the gas supply is turned off at the wall valve before connecting the appliance. The gas supply connections should be made by a qualified technician and in accordance with local code or ordinances. In the absence of a local code, the installation must conform t ...

AIR SHUTTER ADJUSTMENT (Griddle or Grill only) Check for the proper burner flame characteristics and adjust air shutters if necessary. Each air shutter is individually tested and adjusted prior to shipment. Normally adjustment is not required, however, vibrations during transit, or variations in the local gas supply may make minor adjustments necessary. Burner flames should be blue and stable with no yellow tips, excessive nose or ...

GENERAL q Placement of unit. q Specified clearance maintained to cabinet surfaces. q Unit level – front to back, side to side. q All packaging material and tie straps removed, drip pans clean and empty. q Backguard attached if there is less than 12” clearance above the cooking surface to combustibles behind unit. q Radiant tray placed in grill unit (if equipped with grill section). The two grill racks in place. ELECT ...

unnecessary service charges. Be sure to check these items first: • Is there a power surge in the area? • Is the household fuse blown or the circuit breaker tripped? • Is the Range disconnected from the electrical supply? IF THE BURNERS DO NOT IGNITE: • Are the burner caps properly aligned on the burner bases (sealed burners)? • Are the burner ports clogged? • Is a fuse blown or is the c ...

For service, contact one of our PERFORMANCE SERIES SPECIALISTS at 1-866-402-4600. Before you call, please have the following information ready: • Model Number • Serial Number • Date of purchase and Installation • A brief description of the problem • Dealer name Your satisfaction is of the utmost importance to us. If a problem cannot be resolved to your satisfaction, please write or fax us at: Capital Cooking Equipment Attn ...

PERFORMANCE SERIES™ COOKTOPS WARRANTY Two (2) years parts and One (1) year labor, covers the entire unit. Five (5) years parts and Two (2) years labor, covers All Burners (does not include ignition systems). Five (5) years parts and One (1) year labor covers the porcelain enameling on the Burner Grates Limited Lifetime against rust on all stainless steel parts covers entire product. For the life of the product, Capital will re ...