Husqvarna 455 Operator's Manual

Oper ator’s manual (EPA II) Please r ead the operator’s manual carefully and make sure you understand the instructions before using the machine. ...

hine: W ARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: • Approved protective helmet • Approved hearing protection • Protective goggles or a visor Both of the operator ′ s hands must be used ...

.............................................. 2 Symbols in the operator’s manual: ................................ 2 CONTENTS Contents ....................................................................... 3 INTR ODUCTION Dear customer! ............................................................. 4 WHA T IS WHAT? What is what on the chain sa w? ................................... ...

Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant. During over 300 years of continuous operation, ...

hain saw? 23 31 32 26 28 15 16 11 12 13 14 25 24 22 21 20 19 18 17 23 27 1 4 2 5 7 6 9 10 8 3 29 30 1 Cylinder cover 2 Starter handle 3 Air purge 4 Stop switch (Ignition on/off switch.) 5 Rear handle 6 Choke control/Start throttle lock 7 Fuel tank 8 Adjuster screws carburetor 9 Starter 10 Chain oil tank 11 Throttle lockout 12 Decompression valve 13 Front handle 14 Front hand guard 15 Muffler 16 Bar tip ...

UTIONS Bef ore using a new chain saw • Please read this manual carefully. • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly. • Refuel and start the chain saw. See the instructions under the headings Fuel Handling and Starting and Stopping. • Do not use the chain saw until sufficient chain oil has reached the chain. See instructions under the heading ...

UTIONS chain sa w usage if possible. Your dealer, forestry school or your library can provide information about which training materials and courses are available. Work is constantly in progress to improve the design and technology - improvements that increase your safety and efficiency. Visit your dealer regularly to see whether you can benefit from new features that have been introduced. P ersonal protective equipmen ...

UTIONS • The chain brake (A) can either be activated manually (by your left hand) or automatically by the inertia release mechanism. • The brake is applied when the front hand guard (B) is pushed forwards. • This movement activates a spring-loaded mechanism that tightens the brake band (C) around the engine drive system (D) (clutch drum). • The front hand guard is not designed solely to activate the chain brake. ...

• In the felling position the left hand is in a position that makes manual activation of the chain brake impossible. With this type of grip, that is when the left hand is placed so that it cannot affect the movement of the front hand guard, the chain brake can only be activated by the inertia action. Will my hand always activate the chain brake during a kickback? No. It takes a certain force to move the hand guar ...

GENERAL SAFETY PRECAUTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier. The machine′s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine′s handle unit. The body of the chain saw, including the cutting equipment, is insulated from the handles by vibration damping units. Cutt ...

GENERAL SAFETY PRECAUTIONS General rules • Only use cutting equipment recommended by us! See instructions under the heading Technical data. • Keep the chain’s cutting teeth properly sharpened! Follow our instructions and use the recommended file gauge. A damaged or badly sharpened chain increases the risk of accidents. • Maintain the correct depth gauge setting! Follow our instructions and use the recommended depth gauge clearance. ...

GENERAL SAFETY PRECAUTIONS Chain • Chain pitch (inches) • Drive link width (mm/inches) • Number of drive links. Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teeth • Never use a blunt chain. When the chain is blunt you have to exert more pressure to force the bar through the wood and the chips will be very small. If the chain is very blunt it will produce wood powder and no chips or ...

GENERAL SAFETY PRECAUTIONS • File all the teeth to the same length. When the length of the cutting teeth is reduced to 4 mm (0.16") the chain is worn out and should be replaced. General advice on adjusting depth gauge setting • When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recommended depth gauge setting. S ...

GENERAL SAFETY PRECAUTIONS 455e Rancher • Release the knob by folding it out. • Turn the knob anti clockwise to loosen the bar cover. • Adjust the tension on the chain by turning the wheel down (+) for tighter tension and up (-) to loosen the tension. • Tighten the bar clutch by turning the knob clockwise. • Fold the knob back in to lock the tensioning. Lubricating cutting equipment Chain oil Chain oil must demonstrate good adhesio ...

GENERAL SAFETY PRECAUTIONS Checking chain lubrication • Check the chain lubrication each time you refuel. See instructions under the heading Lubricating the bar tip sprocket. Aim the tip of the bar at a light coloured surface about 20 cm (8 inches) away. After 1 minute running at 3/4 throttle you should see a distinct line of oil on the light surface. If the chain lubrication is not working: • Check that the oil channel in the bar is not ...

GENERAL SAFETY PRECAUTIONS Bar Check regularly: • Whether there are burrs on the edges of the bar. Remove these with a file if necessary. • Whether the groove in the bar has become badly worn. Replace the bar if necessary. • Whether the tip of the bar is uneven or badly worn. If a hollow forms on the underside of the bar tip this is due to running with a slack chain. • To prolong the life of the bar you should turn it over daily. ! ...

ASSEMBLY Fitting the bar and chain 455 Rancher, 460 Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle. Remove the bar nuts and remove the clutch cover (chain brake). Take off the transportation ring (A). Fit the bar over the bar bolts. Place the bar in its rearmost position. Place the chain over the drive sprocket locate it in the groove on the bar. Begin on the top edge of the bar. ...

ASSEMBLY Tension the chain by turning the wheel down (+). The chain should be tensioned until it does not sag from the underside of the bar. The chain is correctly tensioned when it does not sag from the underside of the bar, but can still be turned easily by hand. Hold up the bar tip and tighten the bar clutch by turning the knob clockwise. When fitting a new chain, the chain tension has to be checked frequently until the chain is run-in. ...

FUEL HANDLING Fuel Note! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and two- stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture. Gasoline • Use good quality unleaded gasoline. • CAUTION! Engines equi ...

FUEL HANDLING Fueling Clean the area around the fuel cap. Clean the fuel and chain oil tanks regularly. The fuel filter must be replaced at least once a year. Contamination in the tanks causes malfunction. Make sure the fuel is well mixed by shaking the container before refuelling. The capacities of the chain oil tank and fuel tank are carefully matched. You should therefore always fill the chain oil tank and fuel tank at the same time. Fu ...