Intel RS2WC080 Hardware User's Manual
Text of Intel RS2WC080 Hardware User's Manual
Intel RS2WC080 Intel® RAID Controller RS2WC080 Hardware User’s Guide
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL(R)
PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY
INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS
PROVIDED IN INTEL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL
ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY, RELATING TO SALE AND/OR USE
Intel® RAID Controller RS2WC080 Hardware User’s Guide iii
Preface
About this Manual
This is the primary hardware guide for the Intel® RAID Controller RS2WC080, for use
with the SAS and SATA disk drives. It contains installation instructions and
specifications.
For details on how to configure the storage adapters, and for an overview of the software
drivers, see the Intel® RAID Software User’s Guide on the Resource CD.
Audience
This document assumes
Intel® RAID Controller RS2WC080 Hardware User’s Guide v
Table of Contents
Preface ........................................................................................................................iii
About this Manual ................................................................................................................. iii
Audience ..........................................................................................................
Intel® RAID Controller RS2WC080 Hardware User’s Guide vii
List of Figures
Figure 1. Changing the Bracket................................................................................................. 8
Figure 2. Installing the Intel® RAID Controller RS2WC080....................................................... 9
Figure 3. Connecting Cables between the RAID Controller and Drives/Backplane................ 10
Figure 4. Card Layout.....................
Intel® RAID Controller RS2WC080 Hardware User’s Guide ix
List of Tables
Table 1. Jumper Description ...................................................................................................13
Table 2. Technical Specifications ............................................................................................14
Table 3. Array Performance Features .....................................................................................15
Ta
Intel® RAID Controller RS2WC080 Hardware User’s Guide 1
1
Overview
The Intel® RAID Controller RS2WC080 is an intelligent PCI Express* 2.0-compliant
SAS/SATA II RAID controller that offers reliability, good performance, and fault-tolerant
disk subsystem management. This is a RAID solution that meets the internal storage needs
of workgroup, department, or enterprise systems to use cost-effective SATA or high-
performance SAS media.
As a second-generation
Intel® RAID Controller RS2WC080 Hardware User’s Guide Intel® RAID Controller RS2WC080
The Intel® RAID Controller RS2WC080 is a PCI* Express 2.0, half-size, low profile
RAID controller based on the LSI*SAS2008 PCI* Express-SAS/SATA I/O Processor
chip, providing both a SAS controller and RAID engine. With eight independent ports
supporting 6Gb/s and 3Gb/s SAS data transfers using two SFF-8087 mini multi-lane
connectors, this controller supports up to
Intel® RAID Controller RS2WC080 Hardware User’s Guide 3
All operating systems supported by the RAID controller may not be supported by your
server board. To verify compatibility, see the Tested Operating System List for your server
board at http://www.intel.com/support/motherboards/server/.
To make sure the RAID controller supports your operating system, refer to the Tested
Hardware and Operating System List for the Intel® RAID Controller RS2WC080.
Usa
Intel® RAID Controller RS2WC080 Hardware User’s Guide Redundancy and Error Handling
•
In-band SES2.
•
Enclosure management support.
•
Drive coercion (auto-resizing to match existing disks).
•
Support the internal SAS Sideband signal SFF-8485 (SGPIO) interface.
•
Auto-detection of failed drives with transparent rebuild. There must be disk activity
(I/O to the drive) for a missing drive to be marked as failed.
•
Auto-resume on reboot of init
Intel® RAID Controller RS2WC080 Hardware User’s Guide 5
•
Supports SMP to communicate topology management information.
•
Supports single PHY or wide ports consisting of 2, 3, or 4 PHYs within a single
quad port.
•
Allows addressing of multiple SATA targets through an expander if using SATA 2.0-
compliant hard disk drives.
•
Allows multiple initiators to address a single target (in a fail-over configuration)
through an expander.
Note:
All expande
Intel® RAID Controller RS2WC080 Hardware User’s Guide 7
2
Intel® RAID Controller RS2WC080
Hardware Installation
Requirements
•
An Intel® RAID Controller RS2WC080 with the provided cables
•
A host system with an available x8 or x16 PCI-Express* slot
•
The Resource CD, which contains drivers and documentation
•
SAS or SATA 3.0 hard drives
Note:
SATA II is the only type of SATA supported by this RAID Controller.
In addition, Intel Corporation str
Intel® RAID Controller RS2WC080 Hardware User’s Guide Figure 1. Changing the Bracket
4.
Install the RAID controller into an available server system x8 or x16 PCI-Express*
slot (see Figure 2). To locate an appropriate slot and for instructions on installing an
add-in card, see your server system documentation.
AF003344
Intel® RAID Controller RS2WC080 Hardware User’s Guide 9
Figure 2. Installing the Intel® RAID Controller RS2WC080
5.
For the first four drives (ports 0 - 3), connect one 4-port combined end of an
internal cable to the right connector (see letter “A” in Figure 3). If you are using
more than four drives without using an expander backplane, connect the second
cable to the left connector (see letter “B” in Figure 3). Connect the other end of the
cab
Intel® RAID Controller RS2WC080 Hardware User’s Guide Figure 3. Connecting Cables between the RAID Controller and
Drives/Backplane
6.
Install the server system cover and connect the power cords. For instructions, see
your server system documentation.
AF003346
D
Ports 4-7
Ports 0-3
A
C
B