Jensen UV9 Instruction Manual

in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new Jensen Phase Linear UV9 Mobile Multimedia Receiver for maximum enjoyment. Preparation....................................................................................................................... ...

Linear UV9 Mobile Multimedia Receiver. It’s a good idea to read all of the instructions before beginning the installation. We recommend having your Jensen Phase Linear UV9 installed by a reputable installation shop. Features DVD • Aspect Ratio - Full and Normal • Fast Forward - 2X, 4X, 8X and 32X • Slow Motion - 1/2, 1/4, 1/6 and 1/7 • Play, Pause, Stop, Next Chapter and Previ ...

navigation features, you must purchase and install the avigation module (NAV101 or NAV102). All installation and operating instructions will be included with the navigation module. Once the navigation module is connected and operating properly, the NAV source mode will become active. While the navigation module is not installed, the NAV option appears gray, indic ...

control lead & power supply of antenna amplifier) External power amplifier control Antenna Jack SUR-R FRONT L FRONT R SUR- L BLUE BLUE/WHITE WHITE/BLACK - GREEN/BLACK - WHITE + GREEN + PURPLE + PURPLE/BLACK - GREY/BLACK - GREY + FRONT L+ FRONT L- FRONT R+ FRONT R- REAR R+ REAR R- REAR L+ REAR L- Car Mute (leave open if not connected) BROWN Car Phone FRONT L FRONT R REAR R REAR L MUTE P.CONT ANT.CO ...

sleeve from the radio. 2. Install the half-sleeve. a. Install adapter if necessary (optional). b. Install half-sleeve into adapter or dashboard (use only the supplied screws). Do not force the sleeve into the opening or cause it to bend or bow. c. Locate the series of bend-tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserte ...

1. CLOSE/OPEN Press to activate the automatic mechanical system and move the TFT monitor into viewing position. Press again to close the TFT. 2. PIC/DISP Press to adjust the Brightness and Contrast (see “Image/ Display Settings” on page 8). With the monitor closed, press to view alternate LCD display information. When the navigation module is connected to the UV9, press and hold to display the navigation user interface. Th ...

Button Function Name Ref# DVD VCD TUNER CD/MP3/USB MENU 1 Enters the main menu of the disc Turns on/off PBC when playing VCD TITLE 2 Enters the title menu of the disc Plays first ten seconds of each chapter/title MUTE 3 Toggles on/off audio output Toggles on/off audio output Toggles on/off audio output Toggles on/off audio output POWER/ 4 Turns the power on/off Turns the power on/off Turns the power on ...

angle Decreases monitor tilt angle Decreases monitor tilt angle Decreases monitor tilt angle 25 Increases monitor tilt angle Increases monitor tilt angle Increases monitor tilt angle Increases monitor tilt angle DISP 26 Selects display mode: FULL or NORMAL Selects display mode: FULL or NORMAL 1, 2, 3, 4, 5, 6, 7, 8, 9, 0 (Numeric Keypad) 27 Directly accesses chapter 1- ...

Open/Close TFT Monitor Open TFT Monitor Press the OPEN button (1) on the front panel or press the ( ) button (31) on the remote control to activate the mechanism that moves the display panel into the viewing position. Close TFT Monitor Press the OPEN button (1) on the front panel or press the ( ) button (31) on the remote control to load the display panel back into the compartment. TFT Monitor Auto Open If “TFT Auto Open” is ...

Press the /SRC button (10) on the unit (or the button (4) on the remote control) to turn the unit on. The buttons on the front of the unit light up and the current mode status appears in the LCD (7). You can also turn on the unit by pressing the OPEN button (1) and opening the TFT screen. Press and hold the button to power off the unit.The monitor is drawn back into the main compartment. Audible Beep Confirmati ...

inactivity. To exit quickly, touch the top left corner of the screen or press and hold the rotary encoder (11). System Reset To correct a system halt or other illegal operation, use the tip of a pen to press the reset button (12) located on the front bottom-right corner of the unit. After a system reset, the unit restores all factory default settings. NOTE: If the unit is reset while a DV ...

the remote control or touch the button on the screen to enter the “SETUP” menu. The “GENERAL” sub-menu appears highlighted in blue. Accessing Menu Items Touch the sub-menu name, press the <<, >>, |<<, or >>| direction buttons (20, 12, 15, 17) on the remote control to select a sub-menu (Language, Audio, RDS, etc.). The features available for adjustment under the highlighted ...

Demo Sub-Menu Features You can stop/run demonstration mode or turn Demo Auto Run on/off by chooing the “Demo” option from the SETUP MENU. When "Demo Auto Run" is Off, you can select "Demo Mode > Run" to start Demo Mode. Demo Mode scrolls through the various source screens, simulating activity on the display. “Demo Mode” is discreetly displayed in yellow text (below the clock), to indicate the unit is in Demo Mode. To ...

1. Current radio band indicator 2. Radio frequency indicator 3. Clock 4. Stereo broadcasting indicator 5. Strong Local signal broadcasting indicator 6. Preset radio stations: Touch to recall preset stations 7. Information about the current function 8. Touch for quick access to Equalizer level settings 9. Touch to access the direct entry screen 10. Current preset station indicator 11. |<<: Touch to seek backward 12. ...

Auto Store (AS) To select six strong stations and store them in the current band: 1. Select a band (if needed). 2. Press the AS button (3) on the control panel or touch AS (16) on the screen for 2 seconds to activate the Auto Store function. The new stations replace stations already stored in that band. Preview Scan (PS) To scan the AM or FM band for a preview of available stations in your particular area, touch the P ...

NOTE: When properly installed, DVD video cannot be displayed on the main TFT screen unless the parking brake is applied. If you attempt to play a DVD while the vehicle is moving, the TFT screen displays “PARKING” with a blue background. Rear video screens, if applicable, will operate normally. Opening/Closing the TFT Video Screen Opening the TFT Screen To open the TFT video screen, press the OPEN button (1). The unit beep ...

Chapter search. • For VCD mode, press the GOTO button to choose between Track Search, Disc Search and Exit. 3. Enter a time into the field using the numeric keypad (29) on the remote control. 4. Press the >/|| button (18) on the remote control or press the rotary encoder (11) to go to the specified location on the disc. 5. Press the GOTO button again to exit. Direct Chapter / Track Selection Remote C ...