JVC RX-6042S Instructions Manual

INSTRUCTIONS TA/NEWS/INFO DISPLAY MODE Cover_RX-6042[B]0.p65 04.12.23, 6:14 PM 3 ...

IMPORTANT for the U.K. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. If nonetheless the mains plug is cut off ensure to remove the ...

Caution: Proper Ventilation To avoid risk of electric shock and fire and to protect from damage. Locate the apparatus as follows: Front: No obstructions open spacing. Sides: No obstructions in 10 cm from the sides. Top: No obstructions in 10 cm from the top. Back: No obstructions in 15 cm from the back. Bottom: No obstructions, place on the level surface. In addition, maintain the best possible air circulation as illustrated. Floor ...

This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. Do read the operating instructions before you attempt to use the equipment. Do ensure that all electrical connections (including the mains plug, extension leads and int ...

This mark indicates that ONLY the remote control CAN be used for the operation explained. Remote NOT This mark indicates that the remote control CANNOT be used for the operation explained. Use the buttons and controls on the front panel. Adjusting Sound ........................................ 26 Basic Adjustment Items............................................................ 26 Basic Procedure......................................... ...

1 STANDBY/ON button and STANDBY lamp (11) 2 SURROUND/DSP OFF button (30, 32) 3 DSP button (31, 32) 4 SURROUND button (30) 5 Remote sensor 6 Display (For details, see “Display” on the next page.) 7 INPUT ANALOG button (14) INPUT ATT button (14) 8 INPUT DIGITAL button (13) 9 DIMMER button (14) p MASTER VOLUME control (12) q PHONES jack (13) w Source selection buttons (11, 14) DVD M ...

1 TV/STB selector (36) 2 10 keys for selecting preset channels (17, 34) 10 keys for sound adjustment (27, 34) 10 keys for operating audio/video components (34 – 36) 3 SOUND button (27, 34) 4 REC PAUSE button (35, 37) 5 Source selection buttons (11, 12) TAPE/CDR, CD, DVD, DVD MULTI, FM/AM, TV SOUND, VCR 6 FM MODE button (17, 34) 7 SURROUND button (30, 34) 8 DIMMER button (14, 34) 9 TV/VIDEO button (35 ...

DIGITAL IN (DVD) DIGITAL 3 ( TV ) SUBWOOFER OUT RIGHT LEFT FRONT SUB WOOFER AUDIO COAXIAL FM 75 8 16 RIGHT SURR LEFT MONITOR OUT DVD IN OUT (REC) VCR IN (PLAY) VIDEO S-VIDEO DVD IN VCR ...

power supply. Before Installation General Precautions • Be sure your hands are dry. • Turn the power off to all components. • Read the manuals supplied with the components you are going to connect. Locations � ...

Turn the loop until you have the best reception. Notes: • If the AM (MW) loop antenna wire is covered with vinyl, remove the vinyl by twisting it as illustrated. • Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception. • If reception is poor, connect an outdoor single vinyl-covered wire (not supplied) to the AM EXT terminal. Keep the AM (MW) lo ...

To audio input Cassette deck or CD recorder Connecting the subwoofer You can enhance the bass by connecting a subwoofer. Connect the input jack of a powered subwoofer to the rear panel, using a cable with RCA pin plugs (not supplied). Placing speakers Front speakers (L/R) and center speaker (C) • Place these speakers at the same height from the flo ...

R L R L VCR IN F G TV Å To audio output ı To component video input Ç To S-video input Î To composite video input TV Video component connections Use the cables with RCA pin plugs (not supplied). Connect the white plug to the audio left jack, the red plug to the audio right jack, and the yellow plug to the vi ...

output (5.1-channel reproduction) jacks: This connection is the best connection method for enjoying DVD Audio sounds. • When a DVD Audio disc is played back, the original hi ...

DIGITAL 3 (TV) Digital Connections By connecting the receiver and the source component through the digital terminals, sound reproduction quality will be much improved. In addition, you can enjoy multi-channel reproduction and some other convenient functions. IMPORTANT: • When connecting a video component using the digital terminals, you also need to connect it to the video jacks on the rear. Without connecting ...

Operations hereafter will be explained using the buttons on the front panel. You can also use the buttons on the remote control for the same functions if they have the same and similar names/marks. Selecting the Source to Play When you have connected digital source components using the digital terminals, first change the input mode for these components to the di ...

By checking the following indicators, you can easily confirm which speakers you are activating and which signals are coming into this receiver. What speaker indicators light depends on the speaker setting (for details, see “Setting the Speakers” on page 23). • The frames of “L,” “C,” “R,” “LS,” and “RS” light up, when the corresponding speakers ar ...

You can enjoy not only stereo software but also multi- channel software through the headphones. (Sounds are down-mixed to the front channels while playing multi-channel software.) 1 Press SPEAKERS ON/OFF to deactivate the speakers. “HEADPHONE” appears for a while, and the H.PHONE indicator lights on the display. • If the Surround or DSP mode has been activated, “3D H PHONE” appears for a while (and the DSP indicator ...

When the input level of the analog source is too high, the sounds will be distorted. If this happens, you need to attenuate the input signal level to prevent the sound distortion. • Once you have made adjustment, it is memorized for each analog source. Press and hold INPUT ATT (INPUT ANALOG) so that the INPUT ATT indicator lights up on the display. • Each time you press and hold th ...

remote control. Reinforcing the Bass You can boost the bass level. • Once you have made adjustment, it is memorized for each source. Press BASSBOOST to boost the bass level. The BASS BOOST indicator lights up on the display. • Each time you press the button, Bass Boost turns on (“BASSBOOST ON”) and off (“BASSBOOST OFF”) alternately. Note: This function affects only the sounds from th ...

You can browse through all the stations or use the preset function to go immediately to a particular station. VOLUME AUTO MUTING VOLUME TUNED STEREO AUTO MUTING VOLUME TUNED STEREO AUTO MUTING Tuning in to Stations Manually 1 Press FM or AM to select the band. The last received station of the selected band is tuned in. 2 Press FM/AM TUNING 5 or ∞ repeatedly until you find the frequency you want. • Pressing FM/AM TUNING ...