KENT Plus 24C User Manual Manual

Razor™ Plus 24D-26D-28D Razor™ Plus 24C-28C INSTRUCTIONS FOR USE KENT model: 908 7041 020 - 908 7038 020 - 908 7039 020 908 7042 020 - 908 7040 020 INSTRUCTIONS D’UTILISATION Modèle KENT: 908 7041 020 - 908 7038 020 - 908 7039 020 908 7042 020 - 908 7040 020 INSTRUCCIONES DE USO Modelo KENT: 908 7041 020 - 908 7038 020 - 908 7039 020 908 7042 020 - 908 7040 020 INSTRUÇÕES DE USO Modelo KENT: 908 7041 020 - 908 7038 020 - 908 7039 020 908 7042 020 - 908 7040 020 ...

ECO 1 4 7 8 9 9a 9b 9c 10 6 5 3 2 B S310170 C S310250 D S31 E S31 ...

Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01 1 INTRODUCTION ................................................................................................................................... 2 MANUAL PURPOSE AND CONTENTS ........................................................................................................... 2 TARGET ........................................................................................................................................................... 2 HOW TO KEEP THIS MANUAL ...................................................................................... ...

2 Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01 INTRODUCTION MANUAL PURPOSE AND CONTENTS The purpose of this manual is to provide the operator with all necessary information to use the machine properly in a safe and autonomous way. It contains information about technical characteristics, operation, machine storage, maintenance, spare parts and safety conditions. Before carrying out any procedure on the machine, the operators and technicians in charge of the maintenance must read this manual carefully. Contact an authorized Kent Service Center in case of doubts regarding the interpretation of the instr ...

Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01 3 – Carefully read all the instructions before carrying out any maintenance/repair operations. – Before using the battery charger, ensure that frequency and voltage values, indicated on the machine serial number plate, match the mains voltage. – Take all necessary precautions to prevent hair, jewelry and loose clothes from being caught in the moving parts. – Do not smoke while charging the batteries. – Do not leave the machine unattended without being sure that the machine cannot move independently. – Do not wash the machine with direct or pres ...

4 Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01 REAR OUTSIDE VIEW DESCRIPTION (See Fig. C) 1. Serial number plate/technical data 2. Machine handlebar 3. Handlebar inclination adjusting knobs 4. Paddle for forward/reverse gear activation and brush/pad-holder rotation 5. Can holder 6. Pocket 7. Tank cover 8. Rear steering wheel 9. Front wheels on fixed axle 10. Wheel cover 11. Brush/pad 12. Brush-holder/pad-holder deck 13a. Brush-holder/pad-holder deck front spoiler 13b. Cylindrical brush-holder deck front spoiler 14. Cylindrical brushes 15. Cylindrical brush-holder deck 16. Squeegee 17. Squeegee fixing ...

Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01 5 TECHNICAL DATA General technical characteristics Dimensions Razor™ Plus 24D Razor™ Plus 26D Razor™ Plus 28D Cleaning width 24.0in (610 mm) 26.0 in (660 mm) 29.1 in (740 mm) Squeegee width 32.0 in (812 mm) 34.0 in (860 mm) Machine height 42.0 in (1,065 mm) Solution tank capacity 21 gal (80 liters) Dirty water tank capacity 21 gal (80 liters) Front wheels diameter 10.5 in (267 mm) Front wheel specific pressure on the ground Less than 0.5 N/mm2 Rear wheels diameter 3.9 in (100 mm) Vacuum motor power 0.68 HP (500 W) Drive motor power 0.27 HP (200 W) Dr ...

6 Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01 WIRING DIAGRAMS (See Fig. K) BAT Battery 24V C1 Battery connector C2 Battery charger signal connector CH Battery charger 24V 25A EB1 Function electronic board EB2 Drive electronic board EB3 Electronic board LED EV1 Water solenoid valve EV2 Recirculation solenoid valve (optional) F1 Function electronic board fuse F2 Drive electronic board fuse HM Hour counter K1 Key switch LD1 Brush switch warning light LD2 Extra pressure warning light M1 Left brush motor M2 Right brush motor M3 Vacuum motor M4 Brush-holder deck actuator M5 Machine drive motor M6 Water re ...

Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01 7 The machine can be supplied in one of the following modes: a) Batteries (lead or gel) already installed on the machine and ready to be used. 1. Check that the batteries are connected to the machine with the connector (30, Fig. C). 2. Insert the ignition key (10, Fig. B) and turn it to “I” position. If the green warning light (9a, Fig. B) turns on, the batteries are ready to be used. If the yellow or red warning light (9b or 9c, Fig. B) turns on, it is necessary to charge the batteries (see procedure in Maintenance chapter). b) Lead batteries installe ...

8 Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01 BEFORE MACHINE START-UP DECK INSTALLATION/REPLACEMENT On the machines from Serial Number 1776829, it is possible to install either a brush-holder/pad-holder deck (12, Fig. C) or a cylindrical brush-holder deck (15). For deck installation/replacement see the procedure in the Maintenance chapter. Brush or pad-holder installation/replacement 1. According to the kind of cleaning to be carried out, the machine can be equipped both with brushes (15, Fig. J) and pad-holders (16) with pads(17) together with the appropriate deck. 2. Insert the ignition key (10, F ...

Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01 9 MACHINE START AND STOP Start 1. Prepare the machine as described in the previous paragraph. 2. Lower the squeegee (16, Fig. C) by means of the lever (25). When the lever (25) is lowered, the vacuum system starts operating. When the lever (25) is lifted, the vacuum system stops after a few seconds. 3. Position the solution flow control lever (4, Fig. B) in the most appropriate position, depending on the type of cleaning to be carried out: – “ECO” system: when the lever (4) is in the “ECO” position (5), the machine works in a special condition of ...

10 Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01 Brush overload safety system activation 7. In case of brush motor overload, due to foreign bodies which prevent the brushes/pad-holders from rotating, or to excessively aggressive floors/brushes, the safety system stops the brushes/pad-holders after about a minute of continuous overload. The overload is shown by the three warning lights (9a, 9b, 9c, Fig. B) flashing simultaneously. If the overload takes place during a cleaning with the extra pressure function activated, the system automatically reduces the pressure on the brushes/pad-holders deactivatin ...

Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01 11 Recovery water tank emptying 1. Stop the machine by releasing the paddle (4, Fig. C). 2. Lift the brushes/pad-holder by means of the switch (2, Fig. B). 3. Lift the squeegee by means of the lever (25, Fig. C). 4. Bring the machine to the appointed disposal area. 5. Empty the recovery tank by means of the hose (26, Fig. C). After working, rinse the tank with clean water. Solution tank emptying 6. Carry out steps 1 to 4. 7. Empty the solution tank by means of the hose (27, Fig. C). After working, rinse the tank with clean water. Cylindrical brush debris c ...

12 Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01 SCHEDULED MAINTENANCE TABLE (1): and after the first 8 working hours (2): this maintenance operation must be performed by a Kent authorized Service Center SQUEEGEE CLEANING 1. Drive the machine on a level ground. 2. Check that the ignition key (10, Fig. B) is to “0” position. 3. Lower the squeegee (16, Fig. C) by means of the lever (25). 4. Disconnect the vacuum hose (24, Fig. C) from the squeegee. 5. Loosen the handwheels (17, Fig. C) and remove the squeegee (16). 6. Wash and clean the squeegee; in particular, clean the compartments (1, Fig. D) and ...

Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01 13 SQUEEGEE BLADE CHECK (AND REPLACEMENT) 1. Clean the squeegee (as described in the previous paragraph). 2. Check that the edges (5 and 12, Fig. D) of the front and rear blades lay down on the same level, along all their length; otherwise adjust their height as described below: – disengage the retainer (6) and loosen the wing nuts (7) to adjust the rear blade (4); then tighten the wing nuts and engage the retainer; – loosen the wing nuts (8) to adjust the front blade (3); then tighten the nuts. 3. Check that the front blade (3) and rear blade (4) are ...

14 Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01 SOLUTION FILTER CLEANING 1. Drive the machine on a level ground. 2. Check that the ignition key (10, Fig. B) is to “0” position. 3. Operating on the right lower side of the machine, close the solution tap (5, Fig. F). The tap (5) is closed when it is on the position (6) as to the hoses; it is open when it is on the position (7). 4. Operating on the left lower side of the machine (at the “FILTER” mark), remove the transparent cover (1, Fig. F) and the wire gauze (2); clean and reinstall them on the support (3). 5. Reopen the tap (5, Fig. F). CHAR ...

Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01 15 DISASSEMBLY/ASSEMBLY OF THE BRUSH-HOLDER/PAD-HOLDER DECK OR CYLINDRICAL BRUSH-HOLDER DECK Disassembly 1. If there is recovery water in the tank (5, Fig. G) drain it through the hose (26, Fig. C). 2. If there is solution in the tank (4, Fig. G) drain it through the hose (27, Fig. C). 3. Drive the machine on a level ground. 4. Turn the ignition key (10, Fig. B) to “0” position. 5. Disconnect the battery connector (30, Fig. C). 6. Unscrew the handwheel (3, Fig. J). 7. By means of the handlebar (2, Fig. C) lift the tank assembly (4, Fig J) completely to ...

16 Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01 SCRAPPING Have the machine scrapped by a qualified scrapper. Before scrapping the machine, remove the following components: a) Battery b) Brush c) Pad d) Motors e) Electronic boards CAUTION! The removed components must be disposed of properly according to the Law in force. ...

1 INTRODUCTION ................................................................................................................................... 2 BUT ET CONTENU DU MANUEL .................................................................................................................... 2 DESTINATAIRES ............................................................................................................................................. 2 CONSERVATION DU MANUEL .................................................................................. ...

INTRODUCTION BUT ET CONTENU DU MANUEL Ce manuel se propose de fournir à l'opérateur toutes les informations nécessaires afin qu’il puisse utiliser la machine correctement et la gérer dans la manière la plus autonome et sûre. Il comprend des informations relatives à l’aspect technique, le fonctionnement, l’arrêt de la machine, l’entretien, les pièces de rechange et la sécurité. Avant d’effectuer toute opération sur la machine, les opérateurs et les techniciens chargés de l'entretien doivent lire attentivement ce manuel. En ca ...