TC Electronic Desktop Konnekt 6 User's Manual And Operation Manual

2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9 Do not defeat the saf ...

Manual revision 1.1 – SW – V 1.00 English Version INTRODUCTION Safety Instructions...................................................a EMC/EMI & Certificate of Conformity..................b Table of Contents......................................................3 Introduction...............................................................4 Quick Setup Guide........................... ...

SOFTWARE INSIDE TC Near Control Panel with direct monitor mixer and reverb control EFFECT INSIDE M40 Studio Reverb for PC and Mac - Powered by AlgoFlex™ FEATURES • Big volume control • IMPACT™ mic preamp with 48v phantom power • High-resolution meter • M40 Studio Reverb powered by AlgoFlex™ • Direct monitor control with input/DAW control • Headphone out with separate level control and separate s ...

This quick-guide will help you set up the Desktop Konnekt 6 in a typical application. For further details please refer to later sections of this manual. Unpacking • Open the box from the top and remove cabling. • Lift out the styrofoam insert, then lift out the Desktop Konnekt using both hands. • Remove the Konnekt from its plastic bag. • Inspect your Konnekt for signs of transit damage. • In the unlikely event ...

TYPICAL SETUPS: STEREO IN 9 8 Separate level control is ideal such as when you are in the control-room and a singer in the recording room needs a different headphone level. Linked level control is ideal if you record yourself in front of the computer using headphones, simply because of using the big volume knob is more comfortable. 4 Computer Use the Desktop Konnekt 6 with a laptop or desktop computer with a FireWire interf ...

Use these controls to set the appropriate input level. Set meters to “Input” using the Meter switch button (12). Then adjust the Gain 1 and Gain 2 trims until the meters show a level as close to “0 dB” as possible without clipping. 2 Input Overload LEDs Green: A signal is present on the inputs. Yellow: Indicates that the level is just above -6 dB. Ideally the yellow color should flash at peaks. Red: Indicates th ...

power-supply with equivalent specifications. (12V DC 0.3 Amp). 2 FireWire connector This is an IEEE 1394 connector for connecting the Desktop Konnekt 6 to a computer. The Desktop Konnekt can be bus-powered via FireWire if your computer supports bus power. Please refer to the Appendix section of this manual. Before plugging in the FireWire connector, make sure that the plug is positioned correc ...

The meter indicates the input level. The best signal to noise ratio is achieved when peaks are as close to 0 dB as possible without clipping. Adjust the gain using the GAIN knobs on the Desktop Konnekt 6 and the output level of the external source. 5 – Pan/Balance When the “Mic+Inst” or the “Inst+Inst” scene is selected, this knob acts as the pan control for a channel. When the “Stereo In� ...

will be lit after an overload is detected. vMeterHoldFall: This parameter sets how fast the meter should fall back to normal metering after the OVERLOAD LED has been invoked. 2 File Pressing the File button will open the File menu that allows you to load or save a preset. Load By selecting “Load”, you can navigate to any folder on the system, including shared folders. By default, you will be ...

Press to select one of the following three algorithms: Hall: The Hall reverb simulates a rather large hall while preserving the natural characteristics of the source material. This is excellent for many studio applications requiring medium to long decay times and especially on vocal material. Room: The Room algorithm simulates a relatively small, well furnished room. In such a room, many reflections are absorbed by soft mater ...

the described parameters are relevant for specific Konnekt models only. These parameters are marked! Also notice that the System Settings page handles all units connected as part of your setup. SETUP PAGE 20 When the “Headphone control” option is checked, the big VOLUME knob on the Desktop Konnekt 6 controls both th ...

settings. 2 ASIO Buffer Size (relevant for PCs only) The buffer size* can be set from 32 to 8192 samples. The default buffer size is set to 512 samples. The driver latency is also indicated in ms (milliseconds). The displayed latency is the driver latency only! To calculate the complete latency in your setup you need to add the latency of converters, host (DAW), and plug-i ...

(iTunes, Cubase etc.) to stop playing momentarily. Therefore it is possible to set a safety buffer level preventing these spikes. Select between: Normal Level 1 Level 2 Level 3 Use only as high a buffer level as necessary as the system latency increases with the buffer level. 9 Check For Software Updates If your computer has Internet access, you can allow TC Near to connect to www.tcelectronic.com and che ...

GENERAL Enable WDM WDM is Windows’ audio driver system, and is used for Windows sounds, media player and other applications that don’t support ASIO. Also, applications such as PowerDVD use WDM as their audio driver system. If your audio application supports ASIO, we recommend using the ASIO driver. INPUT/OUTPUT Configuration Desktop Konnekt 6 has two input channels and handles up to four output channels. ...

Before setting your computer in standby mode, the TC Near Control Panel must be shut down. Computers handle standby mode and hibernation in different ways. To prevent instability on the audio interface after the computer is turned back on, the TC Near Control Panel must be closed. Most likely you will also need to close you host application (e.g. Cubase or Logic). No Reverb There can be several reasons why y ...

Firewire: Digital IO Engine: Clock and Jitter Internal Sample Rates: Jitter Rejection Engine: Jitter Rejection Filter: AD/DA Conversion Jitter: Processing Delay DIO @ 96/48 kHz: Unbal. Line/HiZ Inputs Ch. 1/2 Connectors: Sensitivity Range: Impedance: Full Scale Input Level: THD: Dynamic Range: Freq. Response: Crosstalk: ADC A to D Conversion: A to D Delay: Mic. Inputs Ch. 1 Connectors: Sensitivity Full Range: Mic Boost: Impeda ...