Kyocera KM-C2520 Installation Manual

GUIDE D’INSTALLATION DU BUREAU PAPIER GUÍA DE INSTALACIÓN PARA EL ALIMENTADOR DE PAPEL INSTALLATIONSANLEITUNG FÜR PAPIEREINZUG GUIDA ALL’INSTALLAZIONE UNITÀ DI ALIMENTAZIONE DELLA CARTA 供纸工作台安装手册 ペーパーフィーダ設置手順書 PF-750 ...

B Pin ................................................................2 C Retainer........................................................1 D TP screw, M4 × 06........................................ 2 E Stay ..............................................................1 English F Binding screw, M4 × 16.................................2 G Paper siz ...

disconnect the MFP power plug from the wall outlet before starting to install the paper feeder. 1. Remove the lower paper cassette (1) from the MFP. 2. Place the MFP (4) on top of the paper feeder (A) with the positioning pins (2) at the front left and right of the paper feeder (A) aligned with the holes (3) in the base of the MFP. 3. Secure the MFP to the paper feeder (A) using the two pins (B). Proc ...

step 1 to the MFP. 5. Remove the screw (5) and then the cover (6) from the rear of the paper feeder. 6. Remove the screw (7) from the MFP. 4. Remettre en place sur le MFP le tiroir inférieur (1) qui a été retiré auparavant à l’étape 1. 5. Retirer la vis (5) puis le couvercle (6) de l’arrière du bureau papier. 6. Retirer la vis (7) du MFP. 4. Vuelva a colocar el cajón de papel infe ...

drawing, and install the retainer (C) using the screw (7) removed in step 6 and the two M4 × 06 TP screws (D). 9. Refit the cover (6) using the screw (5) removed in step 5. 10.Turn the four adjusters (10) until they reach the floor and adjust them to level the machine. 8. Séparer le câble (8) recouvert par le tube noir et les câbles de signaux comme montr� ...

11. Fit the stay (E) to the lower left of the large paper deck toward the rear using the two M4 × 16 binding screws (F) such that it makes contact with the floor. Note: Do not fit the stay (E) if the document finisher is to be installed. Setting the paper size At the time of shipping, the paper size is set to Letter for inch specifications and A4 for metric specifications. To change the size, follow the pr ...

(13)1 本で固定する。 前側は、上爪 (15) を上溝 (17) の差し込む位置で用紙サイズを確認する。 上溝 (17) の位置：手前（A4）� ...

20 (I) 22 21 21 23 8. Connect the MFP power plug to the wall outlet and turn the MFP main switch on. 9. Run maintenance item 208 and set the paper size for the paper feeder (B5/A4/ Letter). 8. Insérer la fiche d’alimentation du MFP dans la prise murale et mettre l’interrupteur principal du MFP sous tension. 9. Exécuter l’élément d’entretien 208 et régler la taille du papier pour le bureau papier (B5/ A4/Lett ...

1. Connect the MFP power plug to the wall outlet and turn the MFP main switch on. 2. Run maintenance item 993. Select “VTC PG1” and output a test pattern. For full-color machines, run maintenance item 402 and output the test pattern. 3. If the center of the paper (24) and that of the test pattern output (25) do not meet the reference value, perform the following adjustment. Deviation to the left or rig ...

7. Repeat steps 4 to 6 until the centers of the paper and the test pattern meet the reference value. Deviation to the left or right: 1.5 mm or less 6. Reproduire une nouvelle mire. 7. Répéter les étapes 4 à 6 jusqu’à ce que le centre du papier et celui de la mire correspondent à la valeur de référence. Déviation vers la gauche ou la droite : 1,5 mm ou moins 6. Saque un p ...

Note: If the position of the adjuster is changed, adjust the front cover position. If the front cover position is not proper, the cassette may not be fixed with the magnet or the gap between the front cover and the paper feeder body may be opened. 8. Loosen the five screws (28). 9. Move the position of the front cover (29) by the amount of divisions of the level that corresponds to the mov ...