Lindy 42799 Operation & User’s Manual

USB to VGA Adapter User Manual English LINDY No. 42799 www.lindy.com ...

connect an additional display device (CRT/LCD monitor, projector) to your desktop or notebook PC. The connected display can act as mirrored or extended desktop (it can also be used as the primary display) of the main display on your PC. The flexibility of USB 2.0 technology saves the need to open the computer and install a V ...

16bit, 32bit 60Hz,75Hz 1024 *768 16bit, 32bit 60Hz,75Hz 1152 * 864 16bit, 32bit 60Hz 1280 * 720 16bit, 32bit 60Hz 1280 * 768 16bit, 32bit 60Hz 1280 * 800 16bit, 32bit 60Hz 1280* 960 16bit, 32bit 60Hz 1280 * 1024 16bit, 32bit 60Hz 1360 * 768 16bit, 32bit 60Hz 1400 * 1050 16bit, 32bit 60Hz 1440 * 900 16bit, 32bit 60Hz 1680 * 1050 16bit, 32bit 60Hz 1600 * 1200 16bit, 3 ...

continue. Step 3 License Agreement; please read it and select “I accept the terms of the license agreement.” Click “Next” to accept the License Agreement. Step 4 The Microsoft Software Installation Certificate warning dialogue box, please select “Continue Anyway” to continue with the device driver installation. This will not affect the device driver i ...

computer now”. Then, click “Finish” to complete the software installation. Step 6 (After System Reboot) Please connect the external display device (monitor/projector) to the VGA connector of USB VGA Adapter and switch it on. Then plug the USB VGA Adapter into an available USB 2.0 port of your PC or Notebook. Step 7 A Hardware Installation Wizard dialog will show ...

automatically (Recommended)”. And click ”Next” to continue. Step 9 The Microsoft Software Installation Certificate warning dialogue box, please select “Continue Anyway” to continue with the hardware installation. This will not affect the device driver installation and the device usage. The extended display will be shown on 2nd display device. Step 10 Click “Fin ...

Please plug the additional USB VGA Adapter into an available USB 2.0 port of your PC or Notebook. a. A Hardware Installation Wizard dialog will show up, please select “No, not this time” and click “Next” to continue. b. Please select “Install the software automatically (Recommended)”. And click ”Next” to continue. c. Please select “Continue Anyway� ...

correctly, please reboot the computer after the installation. After rebooting the computer, the USB extended display will be shown on the display device. Verifying the device driver installation The following procedure allows you to verify the device driver installation. Please right click “My Computer” � “Properties” � “Hardware” � “Device Manager”. Plug-i ...

Step 1. Start menu: Click “Start” � “ “Control Panel” � “Add or Remove Programs” Select “ USB Display Device (Trigger 1+) 9.xx.xxxx.0159” (driver ver.). Click “Remove” button. Step 2. Unplug the USB VGA ADAPTER and click “OK” to continue. Step 3. Select “Yes, I want to restart my computer now” and click “Finish” to reboot. After reboot, you will com ...

adapter once it’s connected. Please check your operating system and refer to the appropriate installation procedure to begin installing the device driver. Please make sure the USB VGA Adapter is unplugged from your PC or Notebook before executing the setup program. This section illustrates the simple device drive ...

Step 6 Please select “Yes, I want to restart my computer now”. Then, click “Finish” to complete the software installation. Step 7 (After System Reboot) Please connect the external display device (monitor/projector) to the VGA connector of the USB VGA Adapter and switch it on. Step 8 Hardware Driver Setup Process Plug the USB VGA Adapter into an available USB ...

Please plug the additional USB VGA Adapters into another available USB 2.0 port of your PC or Notebook. The setup process will begin automatically. You may see below notification balloons for each additional adapter. Verifying Device Driver Installation The following procedure allows you to verify the device driver installation. Please right click “Computer” � ...

Step 1 Access Program Uninstall: Click “Start” �“Control Panel” Under “Programs”, click “Uninstall a program” Look for “ USB Display Device (Trigger 1+) 9.xx.xxxx.0159” (driver ver.) Click “Uninstall” button. Step 2 Unplug the USB VGA Adapter and click “OK” to continue. Step 3 Select “Yes, I want to restart my computer now” and click “Finish” to r ...

display device described in this section means devices such as CRT, LCD monitor, TV display, projector. Access USB VGA Adapter Utility Make sure the USB VGA Adapter is attached to the PC. Look for this on your Windows Start bar. Right-click this icon to access the variety of functions associated to the adapter ...

under the Extended or Primary display modes. It is a useful function for some rotatable display device. DISPLAY MODES � “EXTENDED” DISPLAY MODE (DEFAULT) The default display mode; this feature allows the attached USB display device to work as an “Extended” display of the on-board screen. The extended working space improves work efficiency. Y ...

A feature to allow the USB display device to act as the main working display. The USB VGA Adapter will work as the main graphics adapter of the computer. The screen connected to the on-board graphics card will then work as the extended display. Please be advised that some display utilities and drivers that ship with certain AGP and built-in display adapters may prevent this option ...