Mace MAS-WA-SYS Operation & User’s Manual

1.1 General system overview 1.2 Introduction to the system 1.3 Items included with the system 1.4 Introduction to the Wireless Alarm Panel 1.5 Introduction to the Panel Sound Alert & Backlight Section 2: Installing the Wireless Alarm System ......................................... ...

A. Powering up the Door/Window Sensor B. Installing the Door/Window Sensor C. Mounting with the double-sided adhesive pad 4.2.2 Installing the Motion Sensor A. Powering up the Motion Sensor B. Installing the Motion Sensor C. Sensor sensitivity D. Walk test E. Mounting using screws 4.2.3 Introduction of Keychain Remote Control A. Introduction B. Operation i. Powering up the Keychain Remote Control ii. Enrolling the ...

1.1 General SyStem Overview CAUTION! The 9V battery in the Wireless Alarm Panel is for power back-up purposes only, and the unit should be supplied with main power (through the AC adaptor) at all times. Difficulty in disarming the Wireless Alarm Panel in ALARM mode may occur when it is powered by the back-up battery alone. This is not a malfunction, and can be resolved by the use of a fresh 9V battery and main power supplied th ...

Other: 9V DC INPUT port For AC/DC adaptor Siren output 120dB Battery compartment: For 9V Alkaline back-up battery 4 x Pin header, 4 x Jumper For House Security Code setting 8 x Pin header, 1 x Jumper For Zone Code setting “RESET” button If you forget the 4-digit PIN, press the “RESET” button located in the battery compartment and enter factory default PIN “ 1–2–3–4 ” followed by to restore f ...

Operating Mode Situation Sound Alert and Backlight Indication 1 ARM Zone triggered under ARM status Alarm duration: Adjustable between 1 – 6 minutes (siren). Default is 1 minute Panel — flashes RED every 1.5 seconds with triggered zone indicated (to stop - enter 4-digit PIN and press ) Alarm set under ARM status No siren. Panel — flashes RED every 5 seconds providing an intruder deterrent (diff ...

• Mark on the wall the points for drilling holes for the wall plugs and mounting screws, and the position for mounting the tamper proof magnet. • Drill the holes, insert wall plugs and locate the mounting screws for the Wireless Alarm Panel. • Ensure the mounting surface for the tamper proof magnet is clean. • Peel back one layer of the protective f ...

Battery icon shows power status: FULL HIGH MIDDLE LOW Battery icon shows when the AC power supply is unplugged or interrupted. 9V battery functions as BACK-UP only and the symbol means LOW BATTERY. The LCD backlight flashes YELLOW for 30 seconds and will blink until the new battery is replaced or the mains power supply (with AC adaptor) is plugged in. AC Adaptor icon When the AC adaptor to the Wireless Al ...

3.2.1 uSinG the Panic alarm Pressing & buttons together on the Keypad or Keychain Remote Control will immediately transmit an alarm signal to the Wireless Alarm Panel, activating the siren, and transmitting an alarm signal to any optional response devices. To disarm the Panic alarm On the Wireless Alarm Panel: Enter your 4-digit PIN followed by to exit from the Panic alarm. On the Keychain Remote Control: Pr ...

The default setting of the Wireless Alarm Panel allows the user 20 seconds to exit the property before the alarm is ARMED. However, this Exit Delay can be adjusted to between 10 — 60 seconds as follows: Keys Description Note 1 (1234 or 4-digit PIN) + You must be in STANDBY mode before adjusting the Exit Delay *To make sure you are in STANDBY mode: - Enter the default PIN “ 1–2–3–4 ” OR your new 4-digit PIN - Press - T ...

to set the new Entry Delay • When is pressed the first time the panel flashes with the number of seconds currently set for the Entry Delay (The factory default setting is 30 seconds) • Each time is pressed the Entry Delay is increased by a further 10 seconds between the adjustable range of 10 — 60 seconds • The Entry Delay time on the LCD display will flash until the setting is completed 4 Press to co ...

On the Keychain Remote Control: Press to ARM the system. On the Wireless Alarm Panel: First make sure the panel is in STANDBY mode, and then ARM the system by taking the following steps: Keys Description Note 1 (1234 or 4-digit PIN) + You must be in STANDBY mode before turning to ARM mode *To make sure you are in STANDBY mode: - Enter the default PIN “ 1–2–3–4 ” OR your new 4-digit PIN - Press . - The panel will display t ...

PIN) + Enter 4-digit PIN for setting followed by The panel will display the below image: 3 Press then to set the ARM mode – Toggle 1, 2, 3, 4, 5, 6, 7, 8 to turn each zone ON or OFF – If no number appears, the zone is turned OFF – The panel will display the below image: 4 Press to complete the setting Confirm the setting and return the panel to STANDBY by pressing h. triGGerS in arm mOde Example: Zone 1 trigger Step Descripti ...

• On the Keychain Remote: Press to activate. • On the Wireless Alarm Panel: First make sure the panel is in STANDBY mode, and then enter into ALERT mode by taking the following steps: Keys Description Note 1 (1234 or 4-digit PIN) + You must be in STANDBY mode before turning to ALERT mode *To make sure you are in STANDBY mode: - Enter the default PIN “ 1–2–3–4 ” OR your new 4-digit PIN - Press . - The panel will disp ...

There are default settings that allow the system to operate after opening the package. These settings can be adjusted to suit your individual requirements The HOME mode allows the system operate in both the ARM and ALERT modes in different zones. HOME mode default setting: Sensor Zone Status (MODE) • Door/Window Sensor 1 ALERT • Door/Window Sensor 2 ALERT • Motion Sensor 8 ARM a. enterinG the hOme mOde • On the Keychain Remote Co ...

Enter 4-digit PIN for setting followed by The panel will display the below image: (One beep indicates that you entered a valid PIN, three beeps indicate that an invalid operation was performed). 3 Press then to set the HOME mode Toggle 1, 2, 3, 4, 5, 6, 7, 8 to turn each zone in different mode Indicates ALERT mode for a zone Indicates ARM mode for a zone Indicates the zone is turned OFF, number will not appear The panel will display ...

• Remove the battery cover; insert new batteries noting the polarity as shown in the diagram below and replace the cover. (Requires 2 x AAA batteries) • Low battery indication: If the batteries need to be replaced, the RED LED on the transmitter will flash slowly. B. inStallinG the dOOr/windOw SenSOrS • Mount the transmitter on a fixed surface such as a door or a window frame. • Mount the magnet on a movabl ...

After mounting the sensor at the desired location, it is important to perform a walk test in order to determine if the sensor is detecting the correct area. The distance at which the sensor can detect motion can be adjusted by altering the angle of the sensor. To reduce the detection range, simply move the sensor downward and move the sensor upward to maximize the range. Note: Enter into ALERT mode before you perform the walk test, so that ...

PIN) + You must be in STANDBY mode before enrolling a new Remote Control onto the Wireless Alarm Panel *To make sure you are in STANDBY mode: - Enter the default PIN “ 1–2–3–4 ” OR your new 4-digit PIN - Press - The panel will display the below image while you are in STANDBY mode: (One beep indicates that you entered a valid PIN, three beeps indicate that an invalid operation was performed). 2 (1234 or ...

If a Remote Control device is damaged or lost, it can be deleted from the system as follows: Keys Description Note 1 (1234 or 4-digit PIN) + You must be in STANDBY mode before deleting a Remote Control from the Wireless Alarm Panel *To make sure you are in STANDBY mode: - Enter the default PIN “ 1–2–3–4 ” OR your new 4-digit PIN - Press - The panel will display the below image while y ...