Maytag 120 V Installation Instructions Manual

Both numbers are listed on the model/serial rating plate located under the lid. Model # _______________________________ Serial # _______________________________ Date of Purchase _______________________ Prendre note des numéros de modèle et de série avant d'installer la laveuse. Les deux numéros sont indiqués sur la plaque signalétique sous le couvercle. Numéro de modèle______________ ...

You can be killed or seriously injured if you don't follow All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and ...

exposed to the weather. Do not store or operate the washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. Proper installation is your responsibility. INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Tools needed Level Utility knife Scissors ...

The standpipe drain requires a minimum diameter standpipe of 2" (50 mm). The minimum carry-away capacity can be no less than 17 gal. (64 L) per minute. The top of the standpipe must be at least 39" (990 mm) high and no higher than 72" (1.8 m) from the bottom of the washer. Recessed Area and Closet Installation Instructions This washer may be installed in a recessed area or closet. The installation spacing shown is in i ...

accordance with local codes and ordinances or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, latest edition. If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path is adequate. Do not ground to a gas pipe. Do not have a fuse in the neutral or ground circuit. A ...

NOTE: Slide washer onto cardboard or hardboard before moving across floor. 1. Move washer close to final position. 2. Put “hook” end of drain hose into laundry tub or standpipe. 3. Estimate the length of drain hose needed when washer is in final position. Hose must be cut exactly to length so “hook” end is held tightly over edge of standpipe. Remove Shipping Strap 1. Remove tape that covers shipping strap. Pull to completel ...

1. Before attaching water inlet hoses, run water through both faucets into a bucket. This will get rid of particles in the water lines that might clog hoses. Mark which is the hot water faucet. 2. Attach bottom hose (inlet marked “H”) to hot water faucet. Tighten coupling to faucet by hand. 3. Attach top hose (inlet marked “C”) to cold water faucet. Tighten coupling to faucet by hand. 4. Use pliers to ...

NOTE: On some models, during factory testing, the timer is advanced partially into the cycle causing the start button to be depressed. Allow timer to advance to the end of the cycle. When the cycle is complete, the timer will reset and the start button will return to the start position. If the timer is not allowed to advance to the end of the first cycle and reset, the wash load will not be comple ...

Check the following if the washer is not operating properly: 1. Power supply cord is plugged in. 2. Circuit breaker is not tripped or fuse is not blown. 3. Timer has been advanced to start of a cycle. 4. Water faucets are turned on. 5. Inlet and drain hoses are not kinked. 6. Washer lid is closed. 7. Inlet valve is not frozen if not protected from the weather. 8. Suds level. Excess suds will slow the spin and cause poor ri ...

Sensitive Electronics ESD problems are present everywhere. ESD may damage or weaken the electronic control assembly. The new control assembly may appear to work well after repair is finished, but failure may occur at a later date due to ESD stress. Use an anti-static wrist strap. Connect wrist strap to green ground connection point or unpainted metal in the washer. -OR- Touch your finger repeatedly to a green grou ...

IMPORTANT: Read all instructions before operating. The lower fabric setting key pads and the digital display are used to set up the controls. The display can contain 4 numbers and/or letters and a decimal point. These are used to indicate the set-up codes and related code values available for use in programming the washer. How to use the key pads to program the controls 1. The LOWER LEFT key pad is used to adjust the values ass ...

TIME-OF-DAY CLOCK, MINUTES This is the TIME-OF-DAY CLOCK, minute setting; select 0-59 minutes by pressing the LOWER LEFT key pad. � Press the LOWER MIDDLE key pad once to advance to next code. TIME-OF-DAY CLOCK, HOURS NOTE: Uses military time or 24 hr. clock. This is the TIME-OF-DAY CLOCK, hour setting; select 0-23 hours by pressing the LOWER LEFT key pad. � Press the LOWER MIDD ...

Coins selected, debit disabled. Press the LOWER RIGHT key pad for this selection. Debit Card selected, coins disabled. Press the LOWER RIGHT key pad for this selection. Enhanced Debit is self-selected when a Generation 2 card reader is installed in the washer.The Ed option cannot be manually selected or deselected. � Press the LOWER MIDDLE key pad once to advance to next code. PRICE SUPPRE ...

MULTI-LOAD WASHER AND DRYER WARRANTY LIMITED WARRANTY ON PARTS For the first five years from the date of purchase, when this commercial appliance is installed, maintained and operated according to the instructions attached to or furnished with the product, Maytag brand of Whirlpool Corporation (thereafter “Maytag”) will pay for factory specified parts or original equipment manufacturer parts to correct ...

CONSERVEZ CES INSTRUCTIONS Lire toutes les instructions avant d’utiliser la laveuse. Ne pas laver des articles qui ont été nettoyés ou lavés avec de l’essence ou imbibés d’essence, solvants de nettoyage à sec, ou autres substances inflammables ou explosives; ces substances peuvent émettre des vapeurs susceptibles de s’enflammer ou d’exploser. Ne pas ajouter d’essence, solvant de nettoyage à sec ...

Rassembler les outils et pièces nécessaires avant d'entreprendre l’installation. Outils nécessaires Niveau Couteau utilitaire Ciseaux Clé à mollette de 8" ou 10" Tournevis à lame plate Pince Seau Pièces fournies Retirer les pièces de la laveuse. Vérifier la présence de toutes les pièces. 1 bride de fixation 2 tuyaux d'arrivée d'eau 4 rondelles plates de tuyau d'arrivée d'eau 2 pieds de nivel ...

Système de vidange avec tuyau de rejet à l'égout Le système de rejet à l'égout nécessite un tuyau de diamètre minimum de 50 mm (2"). La capacité minimum de vidange ne peut pas être inférieure à 64 L (17 gal.) par minute. Le sommet du tuyau de rejet à l'égout doit être au moins à 990 mm (39") de hauteur et au maximum à 1,8 m (72") de la base de la laveuse. Instructions d’installation dans un encastrement ou un placa ...

en conformité avec les codes et règlements locaux en vigueur ou, en l'absence de tels codes, avec le National Electrical Code, ANSI/NFPA 70 - dernière édition. Si les codes le permettent et si on utilise un conducteur distinct de liaison à la terre, il est recommandé qu’un électricien qualifié vérifie la qualité de la liaison à la terre. Ne pas u ...

REMARQUE : Faire glisser la laveuse sur un carton ou une plaque de contreplaqué avant de la déplacer sur le plancher. 1. Placer la laveuse près de son emplacement d'installation final. 2. Mettre l'extrémité en crochet du tuyau de vidange dans l'évier de buanderie ou dans le tuyau de rejet à l'égout. 3. Estimer la longueur de tuyau de vidange nécessaire lorsque la laveuse est à son emplacement d'installation final. ...

robinets d'eau 1. Avant de fixer les tuyaux d’alimentation, faire s'écouler l'eau des deux robinets dans un seau. Ceci éliminera les particules se trouvant dans les canalisations d'eau qui pourraient obstruer les tuyaux. Marquer le robinet d’eau chaude. 2. Fixer le tuyau d’alimentation inférieur (marqué “H”) au robinet d’eau chaude. Serrer à la main les raccords au robinet. 3. Fixer le tuyau d’a ...