Metra Electronics 99-7013 Installation Instructions Manual

99-7013 APPLICATIONS Mitsubishi Outlander 2007-2010 KIT FEATURES • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Double DIN Radio Provision • Stacked ISO Mount Units Provision A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DINBrackets • E) Double DIN Trim Plate • F) Snap In Pocket Harness & Antenna Connections (sold seperately) 70-7005 - Mitsubishi Harness 07-up KIT COMPONENTS A Small Flat Blade Screwdriver/ Panel Removal Tool • Phillips Screwdriver • Socket Set 1-800-221-0932 © COPYRIGHT 2007-2010 METRA ELECTRONICS CORPORATION www.metraonline.com B C D TOOLS REQUIRED: E F

Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . 5 - Double DIN/Stacked ISO Units Provision . . . . . . . . . . . . . . . . . . . . . . . 6 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 TABLE OF CONTENTS 99-7013 *Note: Refer also to the instructions included with the aftermarket radio.

MITSUBISHI OUTLANDER 2007-2010 PASSENGER AIRBAG OFF PASSENGER PASSENGER AIRBAG OFF PASSENGER B C 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 1 Unclip and remove the vents from the left and right side of the factory radio panel. (Figure A) Remove (4) Phillips screws securing the radio chassis. Unplug and remove the chassis. (Figure C) 2 Remove (2) Phillips screws securing the radio trim panel then unclip and remove the panel. (Figure B) 3 4 A Continued on page 2.

MITSUBISHI OUTLANDER 2007-2010 2 Remove the labels from the front of the radio trim panel at each side of the hazard switch by pushing them out from behind the panel. (Retain the labels to be reused during kit prepa- ration) (Figure F) 6 E F Continued to kit preparation. REMOVE “9” PHILLIPS SCREWS (RETAIN SCREWS) D Remove (7) Phillips screws securing the hazard switch assembly to the back of the factory radio trim panel. Unplug the ribbon cable from the hazard switch assembly and remove assembly from panel from rear. (Retain the screws and switch assembly to be reused during kit preparation) (Figure D,E) 5

3 Secure the hazard switch panel into the radio housing using the factory hardware removed previously and apply labels from the front of the factory radio trim panel to front of the Metra radio panel. (Figure A,B) 5 Continue to kit assembly. A PASSENGER AIRBAG OFF PASSENGER B MITSUBISHI OUTLANDER 2007-2010

A B C DIN RADIO PROVISION WITH POCKET Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 1 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) 2 Snap the pocket into the radio housing. (Figure C) 3 Continue to final assembly. *Note: Refer also to the instructions included with the aftermarket radio.

5 B C D ISO MOUNT RADIO PROVISION WITH POCKET Mount the ISO Brackets to the after- market radio using the screws sup- plied with the radio. (Figure A) 1 Slide the radio into the Radio Housing until it snaps into place. (Figure B) 2 Snap the Trim Plate onto the front of the Radio Housing. (Figure C) 3 Snap the pocket into the Radio Housing. (Figure D) 4 Continue to final assembly. *Note: Refer also to the instructions included with the aftermarket radio. A

6 B C DOUBLE DIN/STACKED ISO UNITS PROVISION Cut and remove the center bar from the Radio Housing. (Figure A) 1 Snap the Double DIN Brackets to the inside edge of the Radio Housing. (Figure B) 2 Slide the Double DIN or stacked ISO unit(s) into the bracket/radio housing assembly and secure the Double DIN or stacked ISO unit(s) to the assembly using the screws supplied with the unit(s). (Figure C) 3 Snap the Double DIN Trim Plate onto the front of the Radio Housing. (Figure C) 4 Continue to final assembly. *Note: Refer also to the instructions included with the aftermarket radio. A

FINAL ASSEMBLY (A) Strip wire ends back 1/2" B) Twist ends together C) Solder D) Tape A B C D Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassembly. 1 2 3 FINAL WIRING CONNECTIONS METRA / EIA WIRING CODE 12V Ignition / Acc. . . . . . . . . . Red 12V Batt / Memory. . . . . . . . . Yellow Ground. . . . . . . . . . . . . . . . . . Black* Power Antenna. . . . . . . . . . . . Blue Amp Turn-On . . . . . . . . . . . . . Blue / White Amp Ground. . . . . . . . . . . . . . Black / White Illumination . . . . . . . . . . . . . . Orange Dimmer . . . . . . . . . . . . . . . . . Orange / White Right Front (+) . . . . . . . . . . . . Gray Right Front (-). . . . . . . . . . . . . Gray/ Black Left Front (+) . . . . . . . . . . . . . White Left Front (-). . . . . . . . . . . . . . White / Black Right Rear (+) . . . . . . . . . . . . Violet Right Rear (-) . . . . . . . . . . . . . Violet / Black Left Rear (+) . . . . . . . . . . . . . Green Left Rear (-) . . . . . . . . . . . . . . Green / Black *NOTE: When a Black wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer’s specifications. Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.

www.metraonline.com