Millennia HV-3C Manual
Text of Millennia HV-3C Manual
READ THIS FIRST!
Any changes or modifications not expressly approved by MILLENNIA MEDIA, INC. could
void your authority to operate this equipment under the EC or FCC rules.
1. Copyright: You acknowledge that no title to the intellectual property in the HV-3C is trans-
ferred to you.
2. Inspection: Inspect packing box(es), HV-3C, and cable(s) for damage, unusual marks, or
shortages. It is your responsibility to report damage, shortage, or misshipmen
For your safety and the safety of others, be sure to read and understand all safety and opera-
tional instructions before attempting to use the HV-3C. WARNING: The HV-3C internal
circuitry carries lethal voltages. Carefully observe all warnings, precautions, and instructions
on the HV-3C and as described in the instructions supplied with the unit.
1. WATER, MOISTURE, AND SPILLAGE
Do not attempt to use the HV-3C in, near, or aroun
READ THIS!! The HV-3C operates with lethal operat-
ing voltages — the voltage inside the HV-3C can kill you.
Never, under any circumstances, remove the top cover. Re-
fer to a qualified electronics technician any and all servic-
ing and other operations which require the top cover to be
removed.
Congratulations on your purchase of the Millennia Media HV-3C High Voltage Microphone
Preamplifier. The HV-3C is the result of meticulous
voltage mic input option, a fully balanced audio path, enormous non-padded input and output
headroom, superior technical specifications, world-class internal componentry, optional A/D
conversion, and unparalleled sonic performance, the HV-3 series of microphone preamps is
already becoming a true classic in the professional audio industry — and will remain contempo-
rary well into the next century. Hence, Millennia Media.
HV-3C REAR PANEL
(1) CONV
Millennia HV-3C (5) POWER ENTRY "IEC Power Receptacle"
An IEC-type AC line-power receptacle for use with removable cords. Use only the power cord
provided with the HV-3C unit or equivalent U/L approved type SV, SVT, SJ, or SJT AC power
supply cord. Do not defeat the third pin earth ground.
HV-3C FRONT PANEL
(1) HIGH RESOLUTION GAIN CONTROL
Detented, 36-position gain control employing a superior quality Grayhill mil-spec gold plated
rotary switch. Switch gain is a
(4) SIGNAL INDICATORS "OL" & "SP" LEDs
The green "signal present" (SP) LED indicates that a nominal signal is present at the microphone
input. It is set to illuminate in the neighborhood of -35 dBu. The red "overload" (OL) LED has
been set to illuminate when the balanced output reaches a level of +25 dBu. However, the
HV-3C can produce unclipped, undistorted levels over twice this voltage. Hence, the overload
LED is not an indication of preamp clip
HV-3C GENERAL SPECIFICATIONS
THD + Noise, 20 Hz - 30 kHz, 35 dB gain < .0007%, typ .002 % maximum, +27 dBu out
Frequency Response -3 dB points
Sub 2 Hz to beyond 500 kHz
Frequency Response, Interchannel Deviation < 0.1 dB
Maximum Input Level
+23 dBu
Maximum Output Level
+32 dBu
Input Impedance
6,200 ohms, nominal
Output Impedance
24.3 ohms
Noise (Common source)
-73 dB @ 60 dB gain (-133 dB EIN)
(30 ohm source)
-71 dB @ 60 dB gain (-131 dB EIN)
(15
A WORD ABOUT DPA (Brüel & Kjær) MICROPHONES
At present, Danish Pro Audio (formerly Brüel & Kjær Pro Audio Division) manufactures two
families of 4000-series professional recording microphones. One family is +48VDC phantom
powered, the other is +130VDC direct powered. A primary difference between omni fami-
lies (4003/4 vs. 4006/7) is that the high voltage microphones are transformerless whereas the
phantom powered varieties are transformer cou
Millennia Media will repair this product, free of charge, in the USA, in the event of defect of
materials or workmanship for one (1) year following date of purchase. This warranty is ex-
tended only to the original purchaser. This limited warranty covers failures due only to defects
in materials and workmanship which occur during normal, intended use and does not cover
damage which occurs in shipment or failures which are caused by produc