Mopar K6860631 Instruction Manual
Read Online
Read the Mopar K6860631 Instruction Manual online using the built-in PDF viewer.
Key Pages of Document
Click on the desired vehicle to take you directly to the vehicle specific instructions. 08 RAM/09 RAM HEAVY DUTY – REGULAR CAB 08 RAM/09 RAM HEAVY DUTY – QUAD CAB 09 RAM – REGULAR CAB 09 RAM – QUAD/CREW CAB 300/CHARGER/CHALLENGER CALIBER COMMANDER COMPASS DAKOTA DURANGO/ASPEN GRAND CHEROKEE JOURNEY MINIVAN NITRO/LIBERTY PACIFICA PATRIOT PT CRUISER SEBRING SEDAN/AVENGER SPRINTER WRANGLER Aug 08, 2008 K6860631 Rev. 1 ...
PROCEDURE STEPS: NOTE: Using a test light, verify the cigarette lighter outlet being used is ignition switched. Power must not be supplied with the ignition in the OFF position. NOTE: If equipped with the mini console, proceed to step 4. If equipped with a full console, proceed to step 11. 1. Disconnect and isolate the battery negative cable. 2. Using a trim stick C-4755 or equivalent, disengage the retaining tabs and r ...
shift boot, if equipped. 5. If equipped with a manual transmission, remove the transmission gear shift lever extension. 6. Remove the console inserts, if equipped. 7. Remove the bolts (2) that secure the rear console (1) to the floor panel. 8. Lift up the rear of the floor console to clear the gear shift lever, if equipped. Aug 08, 2008 K6860631 Rev. 1 ...
(3) from the floor. 10. Separate the front clips (1) and remove the mini con- sole. 11. On vehicles with a full center console, using a trim stick C-4755 or equivalent, separate the seven front console bezel clips (2), lift up the back of the bezel (1) and remove. 12. Remove the bolts (1) and lift the rear of the base up to release the front guide pins (5). 13. Remove the front base (2). Aug 08, 200 ...
15. Using a trim stick C-4755 or equivalent, disengage the retainer clips that secure the instrument panel center bezel (1) to the instrument panel. 16. Disconnect the wire harness connectors and remove the center bezel from the vehicle. 17. Open the glove box (1). 18. Release the two glove box stops (2) and lower the glove box downward past the stops. 19. Disengage the glove box hinges from the instrument panel and remove the ...
age compartment (2) to the floor panel (3) and remove the storage compartment from the rear cab trim panel (4). 23. Remove the cap (1) and then the bolt (2) that secures the seat belt (3) to the top of the B-pillar (4) and posi- tion the seat belt out of the way. 24. Using a trim stick C-4755 or equivalent, disengage the retaining tabs that secure the upper B-pillar trim panel (5) to the B-pillar ...
panel (1) and remove the trim panel. 29. Install the Wi-Fi router to the rear cab trim panel with the provided materials. 30. Make a small cut in the rear cab trim panel and route the Wi-Fi router connector through 31. Place the rear cab trim panel into position in the vehi- cle. 32. Connect the wire harness to the Wi-Fi router connec- tor. 33. Route the wire harness down the back of the rear panel ...
other inside of the splice clip (1). 41. Using crimping tool (1), Mopar® p/n 05019912AA or equiv- alent, crimp the splice clip and wires together. 42. Repeat the previous two steps for the ground side wires. CAUTION: Do not use acid core solder. 43. Solder (3) the connection (2) together using rosin core sol- der (1). Aug 08, 2008 K6860631 Rev. 1 ...
heat using a heat gun. Heat the joint until the tubing is tightly sealed and sealant (1) comes out of both ends of the tubing. 45. Place the lower B-pillar trim panel (3) into position and engage the retaining tabs that secure the trim panel to the B-pillar (4). 46. Route the seat belt through the slot provided in the B-pillar trim panel. 47. Install the bolt (2) that secures the seat belt ( ...
install the three fasteners (1) that secure the rear stor- age compartment to the floor panel (3). 51. Place the cowl trim panel (1) into position and engage the retaining tabs to the door sill (3). Aug 08, 2008 K6860631 Rev. 1 ...
panel. 53. Press the two glove box stops (2) and raise the glove box upward. 54. Close the glove box. 55. Position the instrument panel center bezel (1) near the IP and connect the wire harness connectors. 56. Install the instrument panel center bezel onto the IP and fully engage the retainer clips. 57. Install the two lower screws (2). 58. If necessary, install the close out panel (2) or cupholder a ...
tabs engage. 60. If equipped with a mini console, position the console and seat the front clips (1) fully. 61. Install the bolts (2). Aug 08, 2008 K6860631 Rev. 1 ...
the floor panel. 63. Install the inserts. 64. Install the gear shift lever extension. 65. Install the 4WD gear shift boot, if equipped. Aug 08, 2008 K6860631 Rev. 1 ...
(2). 67. Seat the rear of the base to engage the front guide pins (5) and Install the bolts (1). 68. Install the console bezel (1) and engage the seven front console bezel clips (2). 69. Connect the battery negative cable. Aug 08, 2008 K6860631 Rev. 1 ...
PROCEDURE STEPS: NOTE: Using a test light, verify the cigarette lighter outlet being used is ignition switched. Power must not be supplied with the ignition in the OFF position. NOTE: If equipped with the mini console, proceed to step 4. If equipped with a full console, proceed to step 11. 1. Disconnect and isolate the battery negative cable. 2. Using a trim stick C-4755 or equivalent, disengage the retaining tabs and remo ...
shift boot, if equipped. 5. If equipped with a manual transmission, remove the transmission gear shift lever extension. 6. Remove the console inserts, if equipped. 7. Remove the bolts (2) that secure the rear console (1) to the floor panel. 8. Lift up the rear of the floor console to clear the gear shift lever, if equipped. Aug 08, 2008 K6860631Rev. 1 ...
(3) from the floor. 10. Separate the front clips (1) and remove the mini con- sole. 11. On vehicles with a full center console, using a trim stick C-4755 or equivalent, separate the seven front console bezel clips (2), lift up the back of the bezel (1) and remove. 12. Remove the bolts (1) and lift the rear of the base up to release the front guide pins (5). 13. Remove the front base (2). Aug 08, 200 ...
15. Using a trim stick C-4755 or equivalent, disengage the retainer clips that secure the instrument panel center bezel (1) to the instrument panel. 16. Disconnect the wire harness connectors and remove the center bezel from the vehicle. 17. Open the glove box (1). 18. Release the two glove box stops (2) and lower the glove box downward past the stops. 19. Disengage the glove box hinges from the instrument panel and remove the ...
fastener covers (2) located on the grab handle (1). 23. Remove the two bolts (3) that secure the grab handle to the B-pillar and remove the grab handle. 24. Remove the cap (1) and the bolt (2) that secures the seat belt (3) to the top of the B-pillar (4) and position the seat belt out of the way. 25. Using a trim stick C-4755 or equivalent, disengage the retaining tabs that secure the upper B-pi ...
retaining tabs that secure the lower B-pillar trim panel (1) to the B-pillar (2). 27. Remove the seat belt (3) from the lower B-pillar trim panel through the slot provided and remove the trim panel. 28. Remove the cap (1) and then the bolt (2) that secures the seat belt (3) to the top of the C-pillar (4) and posi- tion the seat belt out of the way. 29. Using a trim stick C-4755 or equivalent, dis ...
