Motorola H720 Quick Start Manual

connections, clear calls, and lasting comfort. We’ve crammed all of the main features of your headset into this handy guide, and in a matter of minutes we’ll show you just how easy your headset is to use. So go on, check it out. more information on the Web: www.motorola.com/support Caution: Before using your headset for the first time, please read the important Safety, R ...

Earhook Charging Port Volume Buttons Call Button Indicator Light Microphone Boom ...

Note: Your battery is designed to last the life of your product. It should only be removed by a recycling facility. Any attempt to remove or replace your battery will damage your headset. ...

turn it on & off To turn on your headset, flip the boom to open (extended) position. To turn off your headset, flip the boom closed (folded under the headset body). wear it Your headset comes ready for the right ear. Just open the boom, flex the earhook and loop it over your ear. Make sure the speaker aligns with your ear canal, and the microphone is pointing towards your mouth. Note: To use your headset w ...

5 pair & connect connect and go 1 Turn off any Bluetooth devices previously paired with your headset. 2 Turn on the Bluetooth feature on your phone. 3 Turn on your headset (see page 4 for help). The indicator light becomes steadily lit in blue. 4 Set your phone to search for Bluetooth devices. 5 Select Motorola H720 from the search results on your phone. 6 Select Ok or Yes to pair your headset with your phone. Note: If prompted for the pass ...

6 For daily use, make sure your headset is turned on, and your phone’s Bluetooth feature is on. Your headset and phone will connect automatically! test your connection 1 Turn on your headset and put it on. 2 On your phone, dial a phone number and press the Call/Send key. If your phone and headset are successfully connected, you hear ringing on the headset. ...

Note: Some features are phone/network dependent. To answer a call Press the Call button. ignore a call Press and hold a Volume button until you hear a tone. make a voice dial call Press the Call button and wait for voice prompt. redial last call Press and hold the Call button until you hear two tones. mute or unmute a call Press both Volume buttons. end a call Press the Call button. answer or reject second incoming call Use ...

Press and hold both Volume buttons while not on a call. To save battery power, turn off the headset when not using it. If light shows... your talk time is... red less than 4 hours purple between 4 to 7.5 hours blue up to 8 hours ...

when charging when operating If light shows... your headset is... red charging (battery level less than 50% charge) purple charging (battery level more than 50% charge) blue fully charged If light shows... your headset is three blue flashes powering on/off steady blue in pairing/connect mode rapid blue/purple flashes connecting to your phone quick blue flash receiving or making a call slow blue pulse on a call ...

stops flashing to conserve power, but the headset remains on. slow red flash idle (not connected to a phone) slow purple pulse muting the call steady red trying to connect to your phone quick red flash in a low battery state If light shows... your headset is ...

Your headset is... when you hear... powering on an ascending tone powering off two descending tones receiving a call a ring tone at maximum or minimum volume two short tones when pressing Volume button in a low battery state high/low tones repeated every 60 seconds out of range of your phone no audio indications; deteriorating quality connected to your phone three ascending tones enabling call mute two r ...

a low tone every 10 seconds Your headset is... when you hear... ...

13 tips & tricks a few shortcuts To... reset your headset Caution: This action erases all pairing information stored in your headset. With the headset on, press and hold both Volume buttons and Call button for 10 seconds until the indicator light is steady blue. ...

change for left ear use Open the boom and earhook and gently lift top of the earhook up and off, flip the headset over, and then hook bottom of the earhook onto the lower hinge pin and lift top of the earhook up and on to the upper hingepin. set volume button Close the boom on your headset, press and hold the Volume button you want to assign as “volume up”, and then open the boom. The light flashes blue three ti ...

My headset will not enter pairing mode Make sure that any devices previously paired with the headset are turned off. If the indicator light is not steadily lit in blue, turn off both the other device and headset, wait 10 seconds, then turn headset back on. Wait for the indicator light to become steadily lit in blue, indicating the headset is now in pairing mode. My phone doesn't find my headset Make sure the ind ...

If you have questions or need assistance, contact us at 1-877-MOTOBLU, or visit us at www.motorola.com/ Bluetoothsupport or www.motorola com/bluetoothconnect. ...

Safety Information European Union Directives Conformance Statement EU Conformance Hereby, Motorola declares that this product is in compliance with: • The essential requirements and other relevant provisions of Directive 1999/5/EC • All other relevant EU Directives The above gives an example of a typical Product Approval Number. You can view your product’s Declaration of Conformity (DoC) to Directive 1999/5/EC (to R&TTE ...

license under the copyrights, patents, or patent applications of Motorola or any third-party software provider, except for the normal, non-exclusive, royalty-free license to use that arises by operation of law in the sale of a product. Safety & General Information Safety Information IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION. READ THIS INFORMATION BEFO ...