MTD 240-688A Operator's Manual

Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush- covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws a ...

Please do NOT return the unit to the retailer from which it was purchased, without first contacting Customer Support. Table of Contents BEFORE YOU START ASSEMBLING YOUR NEW EQUIPMENT, please locate the model plate on the equipment and copy the the model number and the serial number to the sample model plate provided to the right. You can locate the model plate by standing at the operating position and looking down at the frame. This Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says ...

out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before at- tempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol. HEED ITS WARNING! Your Responsibility Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine. FOR TURNING, NOT LIFTING POUR TOURNER, PAS POUR LE LEVAGE ...

machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts. 2. Be familiar with all controls and their proper operation. Know how to stop the machine and disengage them quickly. 3. Never allow children under 14 years old to operate this machine. Children 14 years old and over should read and understand the instructions and safe operation practices in this manual and on the machine and be trained and supervised by an adult. 4. Never allow adults to ...

auger/impeller housing or chute assembly. Contact with the rotating parts can amputate hands and feet. 2. The auger/impeller control lever is a safety device. Never bypass its operation. Doing so makes the machine unsafe and may cause personal injury. 3. The control levers must operate easily in both directions and automatically return to the disengaged position when released. 4. Never operate with a missing or damaged chute assembly. Keep all safety devices in place and working. 5. Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an ...

Carton contents are listed below with part numbers in parentheses. 1. Two Ignition Keys (725-0201) 2. 2.6 oz Bottle of 2 Cycle Oil (737-04037) 3. Extension Cord (if so equipped) (629-0236) WARNING: Disconnect the spark plug wire and ground it against the engine to prevent unintended starting. Positioning the Upper Handle 1. Remove packing material, if present. 2. Making sure not to pinch the cable in the process, pivot the upper handle into the operating position as illustrated in Figure 1 until it clicks into place. 3. Tighten the wing knobs to secure the handle in place as in Figure 1. Assembling the Discharge Chute For shipping ...

and oil. Do NOT operate the snow thrower without first reading the engines operator’s manual for instructions regarding proper fuel and engine oil. Choke Lever Activating choke control closes the choke plate on carburetor and aids in starting engine. Refer to the engine manual packed with unit for more detailed instructions. Primer Depressing primer forces fuel directly into engine’s carburetor to aid in cold-weather starting. Refer to engine manual packed with unit for more detailed instructions. Ignition Key Ignition key must be present, inserted in key switch, and in t ...

engine, read, understand, and follow all instructions and warnings on the machine and in this manual. 1. The spark plug wire was disconnected for safety. Attach spark plug wire to spark plug before starting. IMPORTANT: For complete and detailed engine starting, stopping and storing instructions, it is recom- mended that you read the engine manual also included with this unit. Fuel And Oil Mixture WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pip ...

rotate choke lever slowly to the 1/2 Choke position. When the engine begins to run smoothly, move the choke to the OFF position. If engine falters, return to FULL choke, then slowly move to 1/2 then OFF position. To Stop Engine 1. To stop engine, turn ignition key counter-clockwise. Disconnect the spark plug wire from the spark plug to prevent accidental starting while equipment is unattended. To help prevent possible freeze-up of starter, proceed as follows: 1. Run engine for a few minutes before stopping to help dry off any moisture on the engine. 2. Electric Starter: Connect power cord to switch ...

wire and ground it against the engine to prevent unintended starting. WARNING: NEVER attempt to make any adjustments while the engine is running, except where specified in the operator’s manual. Shave Plate 1. To check the adjustment of the shave plate, place the unit on a level surface. The wheels, shave plate and augers should all contact level surface. Note that if the shave plate is adjusted too high, snow may blow under the housing. If the shave plate wears out excessively, or the unit does not self-propel, the shave plate may be too low and needs to be adjusted. NOTE: On new units or units with a new shave ...

disengage the control bail and stop engine. Wait until all moving parts have come to a complete stop. Discon- nect spark plug wire and ground it against the engine to prevent unintended starting. WARNING 6 Adjustments & Maintenance Figure 9 IMPORTANT: Do NOT allow the auger’s rubber paddles to wear to the point where portions of the metal auger itself can come in contact with the pavement. Doing so can result in serious damage to your snow thrower. Replacing Belt WARNING: Before servicing, repairing, or inspecting, disengage the control bail and stop engine. Wait until all moving parts have come to a co ...

thrower with fuel in tank indoors or in poorly ventilated areas, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Drain fuel into an approved container outdoors, away from any open flame. Be certain engine is cool. Do not smoke. Fuel left in engine during warm weather deteriorates and will cause serious starting problems. Do not drain carburetor if using fuel stabilizer. Never use engine or carburetor cleaning products in the fuel tank or permanent damage may occur. WARNING Observe the following, when preparing your snow thrower for off ...

addresses minor service issues. For further details, contact customer assistance. 8 Trouble- Shooting Cause Problem Remedy Engine runs erratic 1. Move choke lever to OFF position. 2. Clean fuel line; fill tank with clean, fresh gasoline. 3. Drain fuel tank. Refill with fresh fuel. 4. Contact Service Center. 1. Unit running on CHOKE. 2. Blocked fuel line or stale fuel. 3. Water or dirt in fuel system. 4. Carburetor out of adjustment. Engine overheats 1. Contact Service Center. 1. Carburetor not adjusted properly. Loss of power 1. Connect and tighten spark plug wire. 2. Remove ice and snow from gas cap. Be certain vent hole is cle ...

14 23 33 31 26 34 42 21 44 25 43 32 25 36 5 7 7 1 6 5 48 19 4 28 47 41 30 37 27 39 3 14 11 15 45 46 12 13 8 22 35 38 51 52 2 10 40 16 18 24 25 20 29 17 50 49 9 Models/Modèles 230-260 ...

page are standard equipment. REF PART NO. NO. N° DE N° DE RÉF PIÈCE DE SCRIP TION DE SCRIP TION 1 629-0236 Cord-Extension 110V3M 2 Prong Corde 2 710-0627 Hex L-Bolt 5/16-24 x .75 Gr. 5 Boulon hex 5/16-24 x 0,75 Qual. 5 3 710-1003 Hex Wash B-Tapp Scr #10 x .62" Lg. Vis taraudée no. 10 x 0,62 po de lg. * 4 710-0805 Screw-Hex Cap 5/16-18 x 1.5 Gr. 5 Vis à tête hex. 5/16-18 x 1,5 Qual. 5 ** 710-3025 Screw-Hex Cap 5/16-18 x .625 Gr. 5 Vis à tête hex. 5/16-18 x 0,625 Qual. 5 5 712-04063 Flange Locknut 5/16-18 Gr. F, Ny lon Contre-écrou ...

16 Models/Modèles 230-260 � �� �� �� �� �� �� �� �� �� � � �� � �� �� � � �� �� �� �� �� �� �� �� �� �� �� � �� �� �� � �� � � ...

DE SCRIP TION 1 684-04127 Lower Chute Ass’y (Incl. #5-7 and 10) Ens. de la goulotte inf. comp. les nos. 5-7 et 10 2 710-04071 Carriage Screw 5/16-18 x 1.0 Vis ordinaire 5/16-18 x 1,0 3 710-0451 Carriage Bolt 5/16-18 x .75 Boulon ordinaire 5/16-18 x 0,75 4 712-04063 Flange Locknut 5/16-18 Gr. F, Ny lon Contre-écrou à embase 5/16-18 Qual. F, ny lon 5 720-0284 Han dle Knob As sem bly Bou ton 6 731-04388A Chute Han dle Poignée - goulotte d’éjection 7 731-04354B Up per Chute Goulotte supérieur 8 736-0159 Flat Washer .349 ID x .879 OD x .063 Rondelle plate 0,349 D ...

The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the United States and/or its territories and possessions, and by MTD Products Limited with respect to new merchandise purchased and used in Canada and/or its territories and possessions (either entity respectively, “MTD”). MTD warrants this product (excluding its normal wear parts as described below) against defects in material and workman- ship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in ...