Optoma Projectors Operation & User’s Manual

Usage Notice ...................................2 Safety Information ...............................2 Precautions .........................................3 Eye Safety Warnings ..........................5 Product Features ................................5 Introduction ......................................6 Package Overview ..............................6 Product Overview ........................... ...

intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servici ...

maintenance as recommended in this user’s guide. ▀■ Warning- Do not look into the projector’s lens when the lamp is on. The bright light may hurt and damage your eyes. ▀■ Warning- To reduce the risk of fire or electric shock, do not expose this projector to rain or moisture. ▀■ Warning- Please do not open or disassemble the projector as this may cause electric sh ...

sides, and rear of the projector cabinet is critical for proper air circulation and cooling of the unit. The dimensions shown here indicate the minimum space required. If the projector is to be built into a compart- ment or similarly enclosed, these minimum distances must be maintained. 12” (30cm) 12” (30cm) 12” (30cm) 4” (10cm) Do: � �Turn off and unplug ...

▀■ Avoid staring/facing directly into the projector beam at all times. Keep your back to the beam as much as possible. ▀■ When projector is used in a classroom, adequately supervise students when they are asked to point out something on the screen. ▀■ In order to minimize the lamp power, use room blinds to reduce ambient light levels. Product Features ▀■ WUXGA (1920 x 1200) Native resolution ▀■ ...

� WEEE Card (for EMEA only) �Due to different applications in each country, some regions may have different accessories. Power Cord 3.0m Package Overview Unpack and inspect the box contents to ensure all parts listed below are in the box. If something is missing, please contact your nearest customer service center. 2 × AAA Batteries Project ...

2. Lens Door 3. IR Receivers 4. Lamp Door 5. Ventilation (outlet) 6. Indicator LED 7. Projector Cap 8. Tilt-Adjustment Feet 9. Control Panel 10. Input / Output Connections 11. Power Socket 12. Power Switch 1 7 Main ...

2. SOURCE 3. RE-SYNC 4. LENS 5. Information 6. SHUTTER 7. MENU 8. Four Directional Select Keys 9. ENTER 10. ZOOM 11. FOCUS Control Panel 2 5 7 8 3 4 10 11 9 ...

2. Composite Video Input Connector 3. Component Video Input Connector (YPbPr) 4. BNC Input Connector (YPbPr/RGBHV) 5. KensingtonTM Lock Port 6. Wired Remote Input Connector 7. RJ-45 Networking Connector 8. VGA-Out Connector (Mo ...

2. Shutter 3. Function 2 (Program- mable see P.51) 4. Display Mode 5. Freeze 6. Lens Zoom +/- 7. All 8. HDMI 2 9. HDMI 1 10. DVI (Reserved Key) 11. Information 12. Re-Sync 13. Video 14. YPbPr 15. Numbered keypad (for password input) 16. Power Off 17. Pattern 18. Function 1 (Program- mable see P.51) 19. Enter/Help 20. Four Directional Select Keys 21. Menu 22. Lens Shift 23. Format (Image Aspect Ratio) 2 ...

Install the Projection Lens 1 2 5 �Before install or replacing the lens, switch off the power to the projector �Avoid using the remote control or projector keypad button to adjust the lens shift or zoom/ focus while the lens attachment process is carried out. Install Lens Procedure: 1. Unscrew the 2 screws and lift up the lens door. 1 2. Remove the projector cap. 2 3. Push the release lever up to r ...

1 5 4 3 1....................................................................................................Power Cord 2................................................................................................. RS232 Cable 3...... ...

1....................................................................................................Power Cord 2................................................................................................... *BNC Cable 3................. ...

�Turn on the projector first and then select the signal sources. Powering On the Projector 1. Remove the projector cap. 1 2. Securely connect the power cord and signal cable. Power on the switch 2 and the Power LED flashes Red. 3. Turn on th ...

1. Press the “ ” button on the remote control or press the “ ” button on the control panel to turn off the projector. 4 The following message will be displayed on the screen. Press the “ ” button on the remote control or press the “ ” button on the control panel again 4 to confirm otherwise the message will disappear after 15 seconds. When you pressing for the second time, the projector wi ...

projector displays these symptoms. See pages 78-79 for more information. Warning Indicator When the warning indicators (see below) come on, the projector will automatically shutdown:  “LAMP1” or “LAMP2” LED indicator is lit red and if “POWER” LED indicator flashes red.  “TEMP” LED indicator is lit red and if “POWER” LED indicator flashes red. This indicates th ...

Adjusting the Projector’s Height The projector is equipped with elevator feet for adjusting the image height. 1. Locate the adjustable foot you wish to modify on the underside of the projector. 2. Rotate the adjustable ring clockwise to raise the projector or counter clockwise to lower it. Repeat with the remaining feet as needed. Tilt-Adjustment Feet Tilt-Adjustment Ring ...

To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Example:  ST1 Lens: The projector will focus at distances from 3.08 to 68.6 feet (0.94 to 20.9 meters). 10%W 10%W 60%H 20%H Width(W) Height (H) ...

Optoma Model Name WT1 WT2 ST1 TZ1 TZ2 Focal Length (f) (mm) 11.73 18.1~21.72 21.5~28.7 28.6~54.33 54.06~102.7 F number 2.2 2.2-3.33 2.0-3.0 2.2-3.0 2.3~3.16 Zoom Range (Ratio) Fixed 1.2x 1.33x 1.9x 1.9x Zoom & Focus Adjust- ment Motorized Throw Ratio 0.77 1.2~1.45 1.45~1.94 1.94~3.67 3.67~6.98 Throw Distance (m) 0.5~8.3 0.78~15.6 0.94~20.9 1.25~39.5 2.37~75.2 Throw Distance (feet) 1.64~ ...

Power Refer to the “Power On/Off the Projector” section on pages 14-15. SOURCE Press “SOURCE” to select an input signal. RE-SYNC Automatically synchronize the projector to the input source. LENS Adjust Lens shift up/down/left/right Information Display the projection’s information. SHUTTER Open/close the built-in shutter. MENU Press “Menu” to launch the on-screen display (OSD) menu. To exit OSD, ...