Precor M9.1 Owner's Manual

Text of Precor M9.1 Owner's Manual

21. Insert the upper end of a handrail into the upper handrail clamp until the black foam wrap just

touches the clamp. See Diagram 9. Set the base of the handrail on the floor. Repeat this step for the other handrail. Note: Look underneath the upper handrail clamp to be sure that the handrail ends meet in the middle of the clamp. 22. Insert the four u ...

19. Install the incline crank handle (M9.1 only) onto the lift column shaft as shown in Diagram 7.

Precor M9.1 Align the handle with the flat portion of the shaft end. Insert a screw (D) through the handle and crank shaft and tighten the screw securely with the hex key (G) provided. Do not overtighten. 20. Attach the lift column trim by following these steps. Whi ...

The M9.1 or M9.2s Precision Electronic Treadmill must be grounded. If it should malfunction or

Precor M9.1 break down, grounding provides a path of least resistance for electric current which reduces the risk of electrical shock. The treadmill is equipped with a power cord having an equipment- grounding conductor and a grounding plug. The plug m ...

Information Regarding International Use

FCC Communications Commission, part 15 The M9.1 or M9.2s treadmill has tested and it complies with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The M9.1 or M9.2s tr ...

12. Place two external star washers (E) onto two of the upper handrail console screws (B) and

Precor M9.1 align the upper handrail clamp with the mounting holes on the lift column. See Diagram 4. 13. Insert the screws (B) through the handrail clamp and into the lift column. Tighten the screws securely with the hex key (F) provided. 14. Carefully route the ribbon ...

Pick up and rotate the lift column so that the crossbar is at a 90 degree angle to the base of

the treadmill. The guide tube, on the M9.1 only, should align with the grommet hole in the crossbeam. Refer to Diagram 2. If necessary, remove the lower cable connector from inside the crossbar. 4. Slide the crossbar a few inches out of the lift column. I ...

Setting Up the M9.1 or M9.2s Treadmill

Precor M9.1 2 You do not need any special knowledge or experience to set up the M9.1 or M9.2s treadmill. However, you must carefully review and follow the instructions in this manual. If you do not assemble and use this treadmill according to the following guidelines, you could void the Precor limited warranty. Installation ...

Understanding the Electronic Console

Precor M9.1 The electronic console lets you control your workout session. As you work out, the electronic display provides constant feedback about your progress. Information about distance covered, elapsed time, speed, calories burned, and degree of incline is available at any time. Diagram 12 shows an example of the M9.2s el ...

16. Hold the electronic console over the handrail clamp to attach the ribbon cable connector into

Precor M9.1 its receptacle. On the M9.1, make sure that you hold the potentiometer cable away from the receptacle as you push the connector into place. See Diagram 5. Align the tab on the ribbon cable connector with its counterpart located on the receptacle and plug ...

Once you locate your pulse, look at a clock with a second hand, and count the beats for six

Precor M9.1 seconds. Multiply that number by 10 to determine the total number of beats per minute. For example, if you count 14 beats over six seconds, the total number of beats per minute is 140. Compare the total number of beats with your training zone as identified in ...

*Several versions of this owner’s manual exist. This

is a copy of the last version published. If the assembly instructions do not coincide with your treadmill, please call Precor Customer Service.

When using an electrical appliance, basic precautions should always be taken, including the

following: • Read all instructions before using the M9.1 or M9.2s Precision Electronic Treadmill. These instructions are written to ensure your safety and to protect the treadmill. Before beginning any fitness program, you should obtain a complete physical examination by your physician. Il est conseillé de subir un examen médical complet avant d’entreprendr

Always attach the safety clip to your clothing at waist level prior to beginning your workout.

The safety clip is connected by a cord to the magnetic safety key in the electronic console. If you encounter difficulties, you can stop the running belt by pulling on the cord to disengage the magnetic safety key from inside the console. To resume operation, the magnetic safety key must be replaced. • When the treadmill is not being use

Information Regarding International Use

FCC Communications Commission, part 15 The M9.1 or M9.2s treadmill has tested and it complies with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The M9.1 or M9.2s treadmill generates, uses, and can radiate radio frequency energy and, if not installed and used in ac

The M9.1 or M9.2s Precision Electronic Treadmill must be grounded. If it should malfunction or

break down, grounding provides a path of least resistance for electric current which reduces the risk of electrical shock. The treadmill is equipped with a power cord having an equipment- grounding conductor and a grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance wit

Table of Contents

Safety Information ........................................................................................................... ii Important Safety Instructions ........................................................................................... ii Personal Safety................................................................................................................. iii Precor Smart Weight Option—Safety Guidelines ....

Before You Begin

1 Thank you for purchasing the Precor M9.1 or M9.2s Precision Electronic Treadmill. These treadmills feature one of the most sophisticated and beneficial technologies Precor has ever created: Integrated Footplant Technology. Integrated Footplant Technology (IFT) is a microprocessor-regulated motor control system. This patented technology collects motor and belt speed data and uses it to monitor your workout and enhance your safety a

After unpacking the treadmill, open the hardware kit (refer to Diagram 1) and make sure that you

have the following items: (A) Five flanged nuts — for installing the base plate (B) four upper handrail console screws (C) four upper handrail clamp screws (D) one crank handle screw (M9.1 only) (E) two external star washers — handrail clamp to column (F) one 5/32" hex key — upper handrail clamp and display console (G) one 3/

Setting Up the M9.1 or M9.2s Treadmill

2 You do not need any special knowledge or experience to set up the M9.1 or M9.2s treadmill. However, you must carefully review and follow the instructions in this manual. If you do not assemble and use this treadmill according to the following guidelines, you could void the Precor limited warranty. Installation Requirements Follow these installation requirements when installing the treadmill: • Fill out and

Pick up and rotate the lift column so that the crossbar is at a 90 degree angle to the base of

the treadmill. The guide tube, on the M9.1 only, should align with the grommet hole in the crossbeam. Refer to Diagram 2. If necessary, remove the lower cable connector from inside the crossbar. 4. Slide the crossbar a few inches out of the lift column. Insert the top of the lift column into the crossbeam. Push the lift column through until the base pla

12. Place two external star washers (E) onto two of the upper handrail console screws (B) and

align the upper handrail clamp with the mounting holes on the lift column. See Diagram 4. 13. Insert the screws (B) through the handrail clamp and into the lift column. Tighten the screws securely with the hex key (F) provided. 14. Carefully route the ribbon cable through the slot on the left-hand side of the handrail clamp. Note: Right and left are determi

16. Hold the electronic console over the handrail clamp to attach the ribbon cable connector into

its receptacle. On the M9.1, make sure that you hold the potentiometer cable away from the receptacle as you push the connector into place. See Diagram 5. Align the tab on the ribbon cable connector with its counterpart located on the receptacle and plug the connector into the receptacle using your fingers as shown in Diagram 5. The plastic flanges on t

19. Install the incline crank handle (M9.1 only) onto the lift column shaft as shown in Diagram 7.

Align the handle with the flat portion of the shaft end. Insert a screw (D) through the handle and crank shaft and tighten the screw securely with the hex key (G) provided. Do not overtighten. 20. Attach the lift column trim by following these steps. While performing these steps, refer to Diagram 8 for further clarification. a. Position the trim strip

21. Insert the upper end of a handrail into the upper handrail clamp until the black foam wrap just

touches the clamp. See Diagram 9. Set the base of the handrail on the floor. Repeat this step for the other handrail. Note: Look underneath the upper handrail clamp to be sure that the handrail ends meet in the middle of the clamp. 22. Insert the four upper handrail clamp screws (C) into the upper handrail clamp and finger- tighten. Do not tighten the

Note: After extensive use, vibrations from the treadmill may cause the clamp to loosen.

You may need to periodically inspect the screws and, if necessary, tighten the handrail clamp screws using the hex key (G) provided. e. Proceed to the other side of the treadmill and follow steps a through d to complete the installation of the lower handrails. 24. Return to the upper handrail clamp, look underneath the clamp to be sure that the handrail ends meet

Using the M9.1 or M9.2s Treadmill

3 As simple as using the M9.1 or M9.2s treadmill might seem, you should read this section so that you can use it safely and effectively. This section provides information about the electronic console features which include the following: • information about the ON/OFF (I/O) switch • instructions for using the magnetic safety key • a brief description of the electronic console • instructions for changing the

Understanding the Electronic Console

The electronic console lets you control your workout session. As you work out, the electronic display provides constant feedback about your progress. Information about distance covered, elapsed time, speed, calories burned, and degree of incline is available at any time. Diagram 12 shows an example of the M9.2s electronic console display. Displays on the Electronic Console The indicator lights on the electronic

Keys on the Electronic Console

The keys on the electronic console let you change the speed, stop the treadmill, reset the displays, or control which features appear on the display. Each key and its function is explained below: SPEED : Use the SPEED keys to change belt speed. Belt speed starts at .5 miles per hour (mph) and increases in .1 mph (.2 kph) increments while you hold the key. You can increase speed up to 9 mph (14 kph). When you decreas

Changing the Display to U.S. Standard or Metric

The M9.1 or M9.2s treadmill can display speed in either miles per hour (mph) or kilometers per hour (kph). When the treadmill is shipped from the factory, it is set to display in U.S. Standard units of measure. You can easily change these settings by taking the following steps: Note: The treadmill will retain your selection even when it is turned OFF and unplugged. You can change your selection at any

Precor Treadmill Owners Instructions: