PrimaLuna ProLogue Five Owner's Manual
Text of PrimaLuna ProLogue Five Owner's Manual
Table of Contents
Thank you
3
Specifications
4
Warning - Package Contents - Initial Setup
5
Inputs & Controls
6
Adaptive AutoBias™
7
Tube Replacement
8
Fuse Protection
9
Troubleshooting
10
Warranty Information
11
Copyright Durob Audio BV - 2005. All rights reserved.
Reproduction in whole or part of text, logo, graphics or schematics is strictly forbidden
without permission, in writing, of Durob Audio BV
The information in this manual is subject to
We would like to thank you for choosing our PrimaLuna ProLogue Five vacuum tube power amplifier
as part of your music system. The ProLogue Five is the second tube power amplifier of our family of
affordable, high-quality tube products. The designers and builders of the PrimaLuna equipment all
have a long history in high-end audio. We feel that it's time to offer a range of affordable audio
instruments that can easily compete with today's most
36 Watts per channel
Frequency Response
20Hz - 85kHz +/- 0,2dB at rated power; 4Hz - 110kHz -3dB @ 1W
THD with AABB
<0,1% @ 1W; <1% @ 10W; max 2% at rated power into resistive load
S/N Ratio
89 dB (unweighted) ref 1W
Input Impedance
100 kOhm
Input Sensitivity
600mV rms input for rated output power
Gain
28x (29dB)
Power Consumption
125W @ idle; 225W @ rated max. power
Net Weight
37.5 lbs / 17 kg
Shipping Weight
41.9 lbs / 19 kg
Di
To prevent serious injury, electrical shock or fire:
• Do not operate with bottom plate removed.
• Keep away from rain and moisture.
• Always disconnect all cable connections to and from amplifier before changing fuses and/or
tubes.
• Do not replace fuses with any fuse other than the same type and rating as used by the factory.
• Do not replace tubes without reading instructions.
• Do not replace fuses or tubes if you have any doubt a
Inputs and Controls
Front Panel
The front panel of the PrimaLuna models is made from machined aluminium, finished to match the
blue metallic chassis. No controls are available from the front. The power switch is located on the left
side of the amp, just behind the front plate.
Rear Panel
Looking at the rear panel, you will note you have one set of inputs and the pair of speaker terminals.
Attach the positive (+) from your loudspeaker to the 4 or 8 ohm term
Exclusive to PrimaLuna, this circuit monitors and smoothly adjusts bias constantly and instantly. The
genius of this design is that the Adaptive AutoBias™ actually improves the overall sound quality and
performance of the amp. Between 12 and 30 Watts, measured distortion levels drop by over 40%. In
addition, tubes do not have to be matched, and there is no bias (re-)adjustments needed, ever.
Furthermore, the PrimaLuna is equipped w
The 12AX7 and 12AU7 tubes will have a life of about 5,000 to 10,000 hours. The lives of powertubes
are more difficult to predict. This also depends on how "gently" or "roughly" you use your amplifier. In
general -under normal conditions- you can say between 2,000 and 3,000 hours.
Here are some tips on using tubes:
• Do not use treatments on tube pins or in sockets.
• If you decide to experiment with other tube types, it's best not to swap
A note on fuses: If "someone who knows" tells you to wrap fuses with aluminium foil to avoid wasting
money on new ones, it's best not to take his advice. Fuses are safety valves. They should always be
replaced with the exact same value and type.
Warning: Never attempt to check or replace a fuse while the amp is plugged in. Turn it off and unplug
all speakers, components and AC cords before continuing. Wait 10 minutes to let tubes cool do
• No output. Power is on, but power LED is off and tubes do not light up.
Mains fuse is out. Replace fuse as per instructions on page 9.
• No output. Power LED is on and tubes do light up normally.
Plate fuse may be out. Replace fuse as per instructions on page 9.
If the new fuse goes out immediately after replacement, contact us for further assistance.
• Noise coming from one channel.
Noisy tube. First swap the 12AX7 t