Pro-Tech EB-471LF M1 Operation & User’s Manual

Text of Pro-Tech EB-471LF M1 Operation & User’s Manual

EB-471LF Celeron® M

3.5” Embedded Card With VGA /Sound/LAN OPERATION MANUAL COPYRIGHT NOTICE This operation manual is meant to assist both Embedded Computer manufacturers and end users in installing and setting up the system. The information contained in this document is subject to change without any notice. This manual is copyrighted in April, 2006. You may not reproduce or transmit in any form or by any means, electronic, or mechanica

Pro-Tech EB-471LF M1 This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may

TABLE OF CONTENTS

CHAPTER 1 INTRODUCTION 1-1 About This Manual ........................................................ 1-2 1-2 System Specification ...................................................... 1-3 1-3 Safety Precautions ......................................................... 1-5 CHAPTER 2 HARDWARE CONFIGURATION 2-1 Jumper & Connector Quick Reference Table ................ 2-2 2-2 Component Locations .

CHAPTER 3 SOFTWARE UTILITIES

3-1 Introduction …………..........................................…....... 3-2 3-2 VGA Driver Utility ……………………………….…… 3-2 3-3 Flash BIOS Update ..............................................…....... 3-4 3-4 LAN Driver Utility …...........................................…...... 3-6 3-5 Sound Driver Utility ……………………………………

Pro-Tech EB-471LF M1 This chapter gives you the information for EB-471LF. It also

outlines the System specification. Section includes: z About This Manual z System Specifications z Safety precautions Experienced users can skip to chapter 2 on page 2-1 for Quick Start. CHAPTER 1

Chapter 1 Introduction

Page: 1-2 EB-471LF USER′S MANUAL 1-1. ABOUT THIS MANUAL Thank you for purchasing our EB-471LF Celeron® M3.5” Embedded Card enhanced with VGA /Sound/ LAN, which is fully PC / AT compatible. EB- 471LF provides faster processing speed, greater expandability and can handle more task than before. This manual is designed to assist you how to install and set up the system. It contains four chapters. The user can apply this manual for
Chapter 1 Introduction EB-471LF USER′S MANUAL Page: 1-3 1-2. SYSTEM SPECIFICATION z CPU : Intel® Celeron® M processor Ultra Low Voltage without L2 cache onboard Available at 600MHz System bus frequency at 400MHz Auto detect voltage regulator z SYSTEM CHIPSET : Intel® 852GM chipset z MEMORY : Supports up to 1 GB DDR SDRAM. One 200-pin DDR SO-DIMM sockets on board z CACHE : Built-in CPU z REAL-TIME CLOCK / CALENDAR : 256-byte battery backed CMOS RAM.
Chapter 1 Introduction Page: 1-4 EB-471LF USER′S MANUAL z DISPLAY : Built in Intel 852GM, support CRT, LCD. z IDE INTERFACE : One IDE ports support up to two IDE devices. Supports UDMA 33/66/100. z LAN INTERFACE : Intel® 82562ET 10/100 Base-T z SOUND: AC '97 Codec. Reatel ALC202A. Fully Compliant AC '97 Analog I/O Component z SERIAL PORT : Two high speed 16550 Compatible UARTs with Send / Receive 16 Byte FIFOs. COM1 for RS232; COM2 for RS232/422/4
Chapter 1 Introduction EB-471LF USER′S MANUAL Page: 1-5 z OPERATING TEMPERATURE : 0 to 60°C (32°F to 140°F) z INPUT POWER REQUIREMENT : AT power: +5V, +12V Only +5V: +5V only provide power for SBC, It does not have enough power to support expansion card. z BOARD DIMENSION : 102mm x 145mm (4.02” x 5.71”) z BOARD NET WEIGHT : 290 grams (0.64 lb) 1-3. SAFETY PRECAUTIONS Follow the messages below to avoid your systems from damage: 1. Avoid your syst

** QUICK START **

CHAPTER 2 Helpful information describes the jumper & connector settings, and component locations. Section includes: z Jumper & Connector Quick Reference Table z Component Locations z Configuration and Jumper settings z Connector’s Pin Assignments

Chapter 2 Hardware Configuration

Page: 2-2 EB-471LF USER′S MANUAL 2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE COM Port Connector ....................…..................……… COM1, COM2 RS232/422/485 (COM2) Selection .....................……… JP1 Keyboard/Mouse Connector ..........…………......…… DIN1 Reset Connector .........................…....................………. JPANEL1(7,8) Hard Disk Drive LED Connector .........
Chapter 2 Hardware Configuration EB-471LF USER′S MANUAL Page: 2-3 2-2. COMPONENT LOCATIONS J2 1 LVDS1 2 JSFAN1 PW1 43 44 USB1 IDE1 1 2 JP1 2 1 J1 2 1 JPANEL1COM1 COM2 2 1 JP2 JTV1 JP4 DIN1 VGA1 LED1 JP5 BZ1 AC97 INTEL Celeron-M 1 30 LAN1 1 5 6 10 11 15 EB-471LF Connector, Jumper and Component locations
Chapter 2 Hardware Configuration Page: 2-4 EB-471LF USER′S MANUAL 2-3. HOW TO SET THE JUMPERS You can configure your board by setting jumpers. Jumper is consists of two or three metal pins with a plastic base mounted on the card, and by using a small plastic "cap", Also known as the jumper cap (with a metal contact inside), you are able to connect the pins. So you can set-up your hardware configuration by "open" or "close" pins. The jumper can be comb
Chapter 2 Hardware Configuration EB-471LF USER′S MANUAL Page: 2-5 JUMPER DIAGRAMS 2 pin Jumper looks like this Jumper Cap looks like this 3 pin Jumper looks like this Jumper Block looks like this JUMPER SETTINGS Looks like this 3 pin Jumper 2-3 pin close(enabled) Looks like this Jumper Block 1-2 pin close(enabled) 2 pin Jumper close(enabled) 1 1 1 2 1 2 1 1 Looks like this
Chapter 2 Hardware Configuration Page: 2-6 EB-471LF USER′S MANUAL 2-4. COM PORT CONNECTOR COM1 : COM1 Connector COM1 is fixed as RS-232. The pin assignment is as follows : PIN ASSIGNMENT 1 DCD1 2 RX1 3 TX1 4 DTR1 5 GND 6 DSR1 7 RTS1 8 CTS1 9 RI1 10 NC COM2 : COM2 Connector The COM2 is selectable as RS-232/422/485. The pin assignment is as follows : ASSIGNMENT PIN RS-232 RS-422 RS-485 1 DCD2 TX- TX- 2 RX2 TX+ TX+ 3 TX2 RX+ RX+ 4 DTR2 RX- RX- 5 GND GND G
Chapter 2 Hardware Configuration EB-471LF USER′S MANUAL Page: 2-7 2-5. RS232/422/485 (COM2) SELECTION JP1 : RS-232/422/485 (COM2) Selection This connector is used to set the COM2 function. The jumper settings are as follows : COM 2 Function Jumper Settings (pin closed) Jumper Illustrations RS-232 Open RS-422 1-2, 3-4, 9-10 RS-485 1-2, 5-6, 7-8 *** Manufactory default --- RS-232.
Chapter 2 Hardware Configuration Page: 2-8 EB-471LF USER′S MANUAL 2-6. KEYBOARD/MOUSE CONNECTOR DIN1 : Keyboard/Mouse Connector The pin assignments are as follows : PIN ASSIGNMENT 1 KB_DATA 2 MS_DATA 3 GND 5 K/B_VCC 6 KB_CLK 8 MS_CLK 2-7. RESET CONNECTOR JPANEL1 (7,8) : Reset Connector. The pin assignment is as follows : PIN ASSIGNMENT 7 GND 8 RST_SW 2-8. HARD DISK DRIVE LED CONNECTOR JPANEL (2, 4) : Hard Disk Drive LED Connector The pin assignment is

Pro-Tech Computer Hardware Owners Instructions: